Z3K-CTXCUP HOLDER LIGHT-TRANSMITTER

NISSAN LIGHTING System Owner’s Manual Accent Lighting Reference Guide Product Name: PANORAMIC HEADLINER ILLUMINATION / INTERIOR ACCENT LIGHTING Model Number: T99F3 7VA1C / T99F3 7VA2C Indoor accent lighting (if only a lighting system is installed) 1. Control Module (ECU) Power Connector Pin Number Name and type of signal Input / Output Electrical Characteristics Cable type 1 GND N/A GND Single wire 2 Ignition Signal Input 0V (LOW) - 9 to16V (High) Single wire 3 Room Lamp Signal Input 4-16V PWM Single wire 4 BAT_ Saver Power Input 9 – 16 Volt input Single wire 2. Switch Location • The switch is located on the panel left of the steering wheel shown below. Note: Adjustment of the lighting should be done while parked, not while moving to prevent distraction. 3. Control Switch : This compact and intuitive control switch features two responsive buttons for easy operation and a built-in backlight for enhanced visibility in any environment. The "Accent" button allows you to seamlessly toggle between different systems, streamlining your control experience. 4. Switch Logic • 5. Front and Rear Footwell Lights Each footwell light is equipped with an independent white LED, with a maximum current of 20mA per light. These footwell lights are seamlessly managed by a main control box, which is meticulously designed to blend perfectly with any desired ambiance. By interpreting vehicle signals, the control box can seamlessly switch between two brightness levels, ensuring adjustable brightness to meet different preferences. 6. Panoramic Headliner Illumination (If only system equipped) Lightbar strip parameters for reference: • Of the shelf lightbars • Max LED Strip Length: 900 mm • LED: 6500k LEDs • 240 LEDs per meter • IP67 • Typical dissipation of ~6w/meter at max current. 7. Door Pocket Light : • Left and Right Door Pocket white LED Light. 8. Cupholder Transmitter : • The Cupholder Transmitter is securely attached to the cupholder using double-sided adhesive. Its primary function is to wirelessly power the LEDs located at the base of the cupholder, eliminating the necessity for complex wiring. 9. Cupholder Receiver • IP67 • White LED Light FCC certification of this device refers to RF exposure testing under typical operating conditions, taking into account that this device can only be installed in designated vehicles. To demonstrate compliance with RF exposure 2.1093- Portable category, it is acceptable for the passenger to be no more than 9.5 cm from the equipment surface and the driver no more than 17 cm from the equipment surface, according to KDB 951290 Section 3.3. This device is certified as fully compliant with FCC Wireless Power Transmission KDB 680106 requirements only under specified conditions. The FCC certification of this device refers to RF exposure testing performed in typical operating conditions, where a person is no closer than 17cm centimeters from the device surface at all times, except for non-repetitive patterns with transient time intervals in the order of a second. Only in the stated conditions, the device is shown to fully comply with the FCC RF Exposure requirements of KDB 447498. Compliance Information FCC ID: Z3K-CTX IC: 9930A-CTX FCC Notice This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause unacceptable interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the device and receiver. • Connect the device into an outlet on a circuit different from that to which the receiver is connected. • Consult your dealer or an experienced radio/TV technician for help. FCC Warning: To assure continued FCC compliance, the user must use the provided grounded power supply cord and the shielded video interface cable with bonded ferrite cores. Also, any unauthorized change or modifications to this device would void the user’s authority to operate this device. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. ISED Notice: This Class B digital apparatus complies with Canadian ICES-003. Cet Appareil numérique de la classe B est conforme à la narme NMB-003 du Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de rouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 17cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition aux rayonnements IC RSS-102 définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 17 cm entre le radiateur et votre …

Text truncated - open the document above for the full version.

iCertifi Control Number - IC2026ASOP12373 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 22/05/2026 Ref: Attestation Statement Part 2.911(d)(7) Filing FCC ID: Z3K-CTX JET OPTOELECTRONICS CO.,LTD. certifies that, as of the dates of this application, Americas Compliance Consulting LLC dba iCertifi is our designated U.S. agent for service of process for the above referenced FCC ID. Manufacturer accepts to maintain an agent for no less than two year after the grantee has terminated all marketing and importation or the conclusion of any commission-related proceeding involving the equipment. iCertifi accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Americas Compliance Consulting LLC dba iCertifi FCC FRN: 0033399411 Address: 5809 US-2, Suite B, Albeni Plaza Priest River, Idaho 83856, United States Contact Person: Paul Preston Tel: +1 (866) 885-4575 Email: [email protected] Sincerely, JET OPTOELECTRONICS CO.,LTD.Americas Compliance Consulting LLC dba iCertifi FRN: 0021180203FRN: 0033399411 CHI OWENPaul Preston [email protected]@icertifi.com 886-2-5582-1818+1 (866) 885-4575 Signature: Signature:

Applicant Declaration QSF27-14-04 Rev 1.3 March 4, 2025 Page 1 of 2 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Legal Business Name JET OPTOELECTRONICS CO.,LTD. Address 7F-2, No. 300, Yangguang St., Neihu Dist., Taipei City 11491,Taiwan FRN 0021180203 Grantee Code Z3K FCC ID: Z3K-CTX Authorized Contact Name CHI OWEN Contact Phone 886-2-5582-1818 ext. 2202 Contact Email [email protected] I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare; a) in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. b) in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for: (1) labeling the equipment with the exact FCC ID as specified in this application, (2) compliance statement labeling pursuant to the applicable rules, (3) compliance of the equipment with the applicable technical rules, c) if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCC’s technical requirements. d) in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. e) in accordance with ISO 17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements. (1) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. (2) the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. (3) the Applicant shall, upon request by SGS, at the Applicant’s expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. f) neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a “party” for these purposes. g) the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc. terms and conditions as specified in the TCB Application Form 731 (QSF27-14-01). Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Link to the Covered List: Covered List JET OPTOELECTRONICS CO.,LTD. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. JET OPTOELECTRONICS CO.,LTD. (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not] identified on the Covered list, established pursuant to §1.50002, as an entity producing “covered” equipment. JET OPTOELECTRONICS CO.,LTD. (“the applicant”) certifies that the equipment for which authorization is sought does not contain cybersecurity and anti-virus software produced or provided by Kaspersky Lab, Inc. or any of its successors and assignees, including equipment with integrated Kaspersky Lab, Inc. (or any of its successors and assignees) cybersecurity or anti-virus software. Applicant Signature: Date: May 13, 2026 Print Name: CHI OWEN Title: Deputy Manager Applicant Declaration QSF27-14-04 Rev 1.3 March 4, 2025 Page 2 of 2 Original Issue: Jan. 4, 2021 SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States *NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database

Date: May 13, 2026 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding FCC ID: Z3K-CTX To whom it may concern: We, the undersigned, hereby authorize Kevin Tsai / Deputy Manager of Compliance Certification Services Inc. to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with JET OPTOELECTRONICS CO.,LTD. This authorization is valid until further written notice from the applicant. Printed Name: CHI OWEN Title: Deputy Manager Company Name: JET OPTOELECTRONICS CO.,LTD.

Date: May 13, 2026 To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From: JET OPTOELECTRONICS CO.,LTD. 7F-2, No. 300, Yangguang St., Neihu Dist., Taipei City 11491,Taiwan Regarding: Confidentiality Request regarding application for FCC ID: Z3K-CTX LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Printed Name: CHI OWEN Title: Deputy Manager Company Name: JET OPTOELECTRONICS CO.,LTD.

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 1 / 13 Project No.: TM-2603000406P Rev. 00 APPENDIX 1 - PHOTOGRAPHS OF EUT EXTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 2 / 13 Project No.: TM-2603000406P Rev. 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 3 / 13 Project No.: TM-2603000406P Rev. 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 4 / 13 Project No.: TM-2603000406P Rev. 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 5 / 13 Project No.: TM-2603000406P Rev. 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 6 / 13 Project No.: TM-2603000406P Rev. 00 Rear Footwell Light assembly Front Footwell Light assembly This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 7 / 13 Project No.: TM-2603000406P Rev. 00 CUP Holder light Receiver assembly CUP Holder light Receiver This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 8 / 13 Project No.: TM-2603000406P Rev. 00 Light assembly–LH Light assembly–RH This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 9 / 13 Project No.: TM-2603000406P Rev. 00 Switch Cable Power Cable This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 10 / 13 Project No.: TM-2603000406P Rev. 00 Control module

3 4 1.刪除RoSH的QR Code及TRA NO XXXXXXXXX 2.將EAC換成UKCA，更新阿根廷認證碼C-26450 3.VRM WS/WL/RU標籤不再共用，料號進版成R056616505P，變成WS機種專用 20210902Veronica 1 20220223Veronica IFETEL認證碼修改為RCPST6821-3183,料號進版成R056618203P 2026/04/23 1 //// //// 1. Material: 50# Anti-silver Dragon / Matte Varnish 2. Adhesive: Acrylic adhesive 3. Color: Printing in black 4. Tolerance: ±0.5mm 5. Feeding method: Roll feeding 6. The surface shall be free from oil stains, dirt, and damage. 7. The content of lead, cadmium, mercury, hexavalent chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl ethers (PBDE) in the material(s) shall comply with the RoHS Directive. // / / / Ferner LN006 KevinFJ Evans Label Placement Guide YC’s coding principle for S/N. S/N coding principle U25XXXXXXXX Supplier: U YY: The last two digits of Gregorian year MM: Month (01~12) WW: Week number (01~53) XXXX: 0001~9999 (Production quantity) Bartcode: code39 Font: Arial LN006 Cup holder transmitter Product Label printing R115500700T SUPPLIER: JET CUP HOLDER TRANSMITTER ASSEMBLY POWER: DC12V/1.1 WATT MADE IN TAIWAN FCC ID: This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation S/N: U2502XXXXXX JET P/N: R115500700T 10mm 7mm 25mm 30.0mm SUPPLIER: JET CUP HOLDER TRANSMITTER ASSEMBLY POWER: DC12V/1.1 WATT MADE IN TAIWAN FCC ID: This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation S/N: U2502XXXXXX JET P/N: R115500700T Z3K-CTX Z3K-CTX

This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 11 / 13 Project No.: TM-2603000406P Rev. 00 INTERNAL PHOTOGRAPHS OF EUT This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 12 / 13 Project No.: TM-2603000406P Rev. 00 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Page 13 / 13 Project No.: TM-2603000406P Rev. 00 Module Antenna

Project No: TM-2603000406P Page: 1 / 12 Report No.: TMWK2603001361KS FCC ID: Z3K-CTX Rev.: 00 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group 47 C.F.R. Part 2, Subpart J, Section 2.1093 KDB 680106 D01 v04 Maximum Permissible Exposure Report For CUP HOLDER LIGHT-TRANSMITTER Model: R115500700T Trade Name: JET OPTOELECTRONICS CO., LTD. Issued to JET OPTOELECTRONICS CO.,LTD. 7F-2, No. 300, Yangguang St., Neihu Dist., Taipei City 11491,Taiwan Issued by Compliance Certification Services Inc. Wugu Laboratory No.11, Wugong 6th Rd., Wugu Dist., New Taipei City, Taiwan Issued Date: May 13, 2026 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No: TM-2603000406P Page: 2 / 12 Report No.: TMWK2603001361KS Rev.: 00 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 May 13, 2026 Initial Issue ALL Peggy Tsai This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No: TM-2603000406P Page: 3 / 12 Report No.: TMWK2603001361KS Rev.: 00 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ....................................................................................4 2. ACCREDITATION ...........................................................................................................5 3. EUT SPECIFICATION .....................................................................................................6 4. MEASUREMENT EQUIPMENT USED ............................................................................7 4.1 EQUIPMENT USED FOR EMISSIONS MEASUREMENT .......................................7 4.2 MEASUREMENT UNCERTAINTY ..........................................................................7 5. LIMIT ..............................................................................................................................8 6. HUMAN EXPOSURE ASSESSMENT .............................................................................9 6.1 SUPPORT EQUIPMENT .........................................................................................9 6.2 TEST SETUP ..........................................................................................................9 6.3 WORST CASE TEST RESULTS ........................................................................... 10 7. TEST SETUP PHOTO ................................................................................................... 11 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No: TM-2603000406P Page: 4 / 12 Report No.: TMWK2603001361KS Rev.: 00 1. TEST RESULT CERTIFICATION APPLICABLE STANDARDS STANDARD TEST RESULT 47 C.F.R. Part 2, Subpart J, Section 2.1093 KDB 680106 D01 Wireless Power Transfer v04 Compliance Statements of Conformity Determination of compliance is based on the results of the compliance measurement, not taking into account measurement instrumentation uncertainty. Approved by: Tested by: Sky Zhou KW Huang Asst. Section Manager Engineer Compliance Certification Services Inc. Compliance Certification Services Inc. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No: TM-2603000406P Page: 5 / 12 Report No.: TMWK2603001361KS Rev.: 00 2. ACCREDITATION Test Laboratory Name: Compliance Certification Services Inc. Wugu Laboratory Test Laboratory Address: No.11, Wugong 6th Rd., Wugu Dist., New Taipei City, Taiwan. FCC Registration No. : 444940 MRA: APEC TEL This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No: TM-2603000406P Page: 6 / 12 Report No.: TMWK2603001361KS Rev.: 00 3. EUT SPECIFICATION EUT CUP HOLDER LIGHT-TRANSMITTER Model R115500700T Trade Name JET OPTOELECTRONICS CO., LTD. Model Discrepancy N/A Frequency Range 81 ~ 89 KHz Others Device category Portable (<20cm separation) Mobile (>20cm separation) Others Exposure classification Occupational/Controlled exposure General Population/Uncontrolled exposure Antenna Specification Coil Antenna Received Date March 25, 2026 Date of Test April 22, 2026 Remark: 1. For more details, please refer to the User’s manual of the EUT. 2. Disclaimer: Antenna information is provided by the applicant, test results of this report are applicable to the sample EUT received. This document cannot be reproduced except in full, without prior written approval of the Company…

Text truncated - open the document above for the full version.

SPECIFICATION FOR APPROVAL PART CCIL-1202-130K VERSIONA PAGE1 BILL OF MATERIAL CORE: FERRITE, FERROXCUBE OR ACME OR EQUIV. TAPE: #1350F-1. 3M UL FILE NO E17385. OR EQUIV. WIRE: 2UEW JUNG SHING UL FILE NO E174837 OR EQUIV. EPOXY: 6020H WELLS. UL FILE NO E229633 OR EQUIV. TIN : D9930C/SN100 DYFENCO OR EQUIV. ELECTRICAL SPECIFICATION INDUCTANCE: 12.9 uH ± 10% MEASURE AT 100 KHZ 1V. D. C. R. : 0.165 Ω ± 10% MEASURE AT 25 °C. SCHEMATICS PHYSICAL DIMENSION (UNIT:mm): Ø24.5±0.5 19.5 TYP. 10.0 TYP. FRONT VIEW SIDE VIEW BACK VIEW 5.0 TYP. 2.54 MAX. 2.38 TYP.

Project No: TM-2603000406P Page 1 / 29 Report No.: TMWK2603001360KR FCC ID: Z3K-CTX Rev. 01 No.11, Wugong 6th Rd., Wugu Dist., New Taipei City , Taiwan /新北市五股區五工六路11號 t:(886-2) 2299-9720 f:(886-2) 2299-9721 www.sgs.com.tw Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com.tw/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com.tw/Terms-and-Conditions. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of client’s instruction, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced, except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Compliance Certification Services Inc. 程智科技股份有限公司 Member of the SGS Group FCC 47 CFR PART 15 SUBPART C TEST REPORT For CUP HOLDER LIGHT-TRANSMITTER Model: R115500700T Trade Name: JET OPTOELECTRONICS CO., LTD. Issued to JET OPTOELECTRONICS CO.,LTD. 7F-2, No. 300, Yangguang St., Neihu Dist., Taipei City 11491,Taiwan Issued by Compliance Certification Services Inc. Wugu Laboratory No.11, Wugong 6th Rd., Wugu Dist., New Taipei City, Taiwan Issued Date: June 9, 2026 This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No: TM-2603000406P Page 2 / 29 Report No.: TMWK2603001360KR Rev. 01 Revision History Rev. Issue Date Revisions Effect Page Revised By 00 May 13, 2026 Initial Issue ALL Peggy Tsai 01 June 9, 2026 See the following Note Rev.(01) P. 17 Peggy Tsai Rev. (01) 1. Modify Test Data in section 7.1. This document cannot be reproduced except in full, without prior written approval of the Company. 本報告未經本公司書面許可，不可部份複製。 Project No: TM-2603000406P Page 3 / 29 Report No.: TMWK2603001360KR Rev. 01 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION ......................................................................................... 4 2. EUT DESCRIPTION ............................................................................................................. 5 3. TEST SUMMARY ................................................................................................................. 6 4. TEST METHODOLOGY ....................................................................................................... 7 4.1 EUT CONFIGURATION .................................................................................................. 7 4.2 EUT EXERCISE .............................................................................................................. 7 4.3 GENERAL TEST PROCEDURES ................................................................................... 7 4.4 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ........................................ 8 4.5 DESCRIPTION OF TEST MODES .................................................................................. 9 5. INSTRUMENT CALIBRATION ........................................................................................... 10 5.1 MEASURING INSTRUMENT CALIBRATION ................................................................ 10 5.2 MEASUREMENT EQUIPMENT USED .......................................................................... 11 5.3 MEASUREMENT UNCERTAINTY ................................................................................ 12 5.4 FACILITIES AND TEST LOCATION .............................................................................. 12 6. SETUP OF EQUIPMENT UNDER TEST ............................................................................ 13 6.1 SUPPORT AND EUT ACCESSORIES EQUIPMENT .................................................... 13 6.2 TEST SETUP DIAGRAM ............................................................................................... 14 6.3 TEST PROGRAM .......................................................................................................... 14 7. TEST REQUIREMENTS ..................................................................................................... 15 7.1 20DB BANDWIDTH ....................................................................................................... 15 7.2 TRANSMITTER RADIATED EMISSION ........................................................................ 18 7.3 AC POWER-LINE CONDUCTED EMISSION ................................................................ 28 7.4 COIL …

Text truncated - open the document above for the full version.