Z52NAS-PD07Z1UMotion sensor

1 Motion 5In1 User Manual (NAS-PD07Z1U) VersionWritten ByDateChange List 1.0Yongqi20200330Initial 1.1Yongqi20200529Change Some Errors. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help 2 Thissensorhasmotiondetector,lightintensitysensorandambienttemperature/humiditysensors inonewhichbasedonZ-Wave™Plustechnology. ThisproductcanbeincludedandoperatedinanyZ-Wave™networkwithotherZ-Wave™certified devicesfromothermanufacturersand/orotherapplications.Allnon-batteryoperatednodeswithin thenetworkwillactasrepeatersregardlessofvendortoincreasereliabilityofthenetwork. Z-Wave™NetworkInclusion/Exclusion/Reset Thereisonebuttoninthebacksideofthesensor,itcanbeexecutedinclusion,exclusionandreset fromZ-Wave™network. Add¹ 1 、 Powerupthedevice. 2 、 SetZ-Wave™Controllerintoinclusionmode 3、Pressandholdthebuttonfor5suntilwhite ledlightsison,thenreleasethebutton beforeledturnoff. Blueledwillblinkwith1s intervaluntilinclusion successful. Remove 1 、 Powerupthedevice. 2 、 SetZ-Wave™Controllerintoexclusionmode 3、Pressandholdthebuttonfor5suntilwhite ledlightsison,thenreleasethebutton beforeledturnoff. Blueledwillblinkwith0.5s intervaluntilexclusion successful. FactoryReset² 1、Powerupthedevice. 2 、 Pressandholdthebuttonfor10suntilpink ledlightsison,thenreleasethebutton beforeledturnoff. ProductTestMode 1、Pressandholdthebutton. 2、Poweronthedevice,devicewillenterinto factoryproducttestmodewithwhitelight blinkonetime. SendNIF³ Pressandholdthebuttonfor5suntilwhite ledlightsison,thenreleasethebutton beforeledturnoff. Notice1:Whendeviceentersintoinclusionmode,thedeviceallfunctionalitywillbeuseless.The inclusionmodewillbetimeoutafter30s,usercanimplementstep3toterminateinclusionmode. Notice2:FactoryResetwillclearthedeviceallZ-Wave™Networkdata(includehomeid,nodeid, etc...)savedinmemory,andrestoreallconfigurationparameterstofactorydefault.Pleaseusethis 3 procedureonlywhenthenetworkprimarycontrollerismissingorotherwiseinoperable. Association Thedevicesupports2associationgroups,andeachgroupsupportsmax5associatednodes. 4 Group1islifelinegroup;allnodeswhichassociatedinthisgroupwillreceivethemessagessentby devicethroughlifeline. Group2iscontrollinggroup,allnodesassociatedinthisgroupwillbecontrolledthroughBASIC_SET commandbythedevicewhendevicedetectsamovementevent. TheCommandClasssupportedbyeachassociationgroupisshowninthetablebelow: GroupCommandClassEvent COMMAND_CLASS_NOTIFICATIONNOTIFICATION_REPORT COMMAND_CLASS_SENSOR_BINARYSENSOR_BINARY_REPORT 1(Lifeline)COMMAND_CLASS_SENSOR_MULTILEVELSENSOR_MULTILEVEL_REPORT COMMAND_CLASS_BATTERY¹BATTERY_REPORT¹ COMMAND_CLASS_DEVICE_RESET_LOCALLYDEVICE_RESET_LOCALLY_NOTIFICATION 2(Control)COMMAND_CLASS_BASICBASIC_SET Notice1:{COMMAND_CLASS_BATTERY,BATTERY_REPORT}isvalidonlywhenincludedwithLPM.Pleasesee Page10fordetail. Z-Wave™MessageReport Oncethedevicedetectsamovement,itwillreporttheeventtothecontrollerandcurrentlight intensityvaluewillbefollowed. Indefault,devicewilluseCOMMAND_CLASS_NOTIFICATIONtorepresentthemotionevent.User canalsoenableCOMMAND_CLASS_SENSOR_BINARYreportbysettingthe“ConfigurationNo.5”to ‘1’. NotificationReport MotionDetector Whendevicedetectsamotionevent,itwillautomaticallysendthenotificationreporttonodes associatedinlifeline. CommandClass COMMAND_CLASS_NOTIFICATION Command NOTIFICATION_REPORT Type HOME_SECURITY(0x07) Event MotionDetected HOME_SECURITY_MOTION_DETECTION_UNKNOWN_LOCATION(0x08) MotionCleared HOME_SECURITY_NO_EVENT(0x00) CoverRemovedDetector Whendevicedetectsacoverremovedevent,itwillautomaticallysendthenotificationreportto nodesassociatedinlifeline. COMMAND_CLASS_NOTIFICATIONCommandClass 5 Command NOTIFICATION_REPORT Type HOME_SECURITY(0x07) Event CoverRemoved TAMPERING_COVERING_REMOVED(0x08) CoverClosed HOME_SECURITY_NO_EVENT(0x00) MultilevelSensorReport Thisdeviceembedsinadigitallightsensorandadigitaltemperaturesensor.Thedevicemeasures theambientlightintensityandtemperaturewithacertaintimeintervalthatdecidesby ConfigurationNo.17. LightSensor Whentheambientlightintensitydifferentialover50lux(indefault,anddecidesbyConfiguration No.11),thedevicewillunsolicitedtosenda“SENSOR_MULTILEVEL_REPORT”tonodeswhich associatedinlifeline. CommandClassCOMMAND_CLASS_SENSOR_MULTILEVEL CommandSENSOR_MULTILEVEL_REPORT TypeLuminance ScaleLux TemperatureSensor Whentheambienttemperaturedifferentialover1°C(indefault,anddecidesbyConfigurationNo. 9),thedevicewillunsolicitedtosenda“SENSOR_MULTILEVEL_REPORT”tonodeswhichassociated inlifeline. CommandClassCOMMAND_CLASS_SENSOR_MULTILEVEL CommandSENSOR_MULTILEVEL_REPORT TypeAirTemperature ScaleFahrenheit(US)/Celsius(OtherRegion) HumiditySensor Whentheambienthumiditydifferentialover2RH%(indefault,anddecidesbyConfigurationNo. 10),thedevicewillunsolicitedtosenda“SENSOR_MULTILEVEL_REPORT”tonodeswhich associatedinlifeline. CommandClassCOMMAND_CLASS_SENSOR_MULTILEVEL CommandSENSOR_MULTILEVEL_REPORT TypeHumidity ScaleRH% 6 CommandClassConfiguration ThedevicesupportsthecontrollertoconfigureparametersofthedevicethroughConfiguration CommandClass,andth…

Text truncated - open the document above for the full version.

FCCID:Z52NAS-PD07Z1U

LabelLocationOnEUT Label ProductName:Motionsensor ModelNo.:NAS-PD07Z1U FCCID:Z52NAS-PD07Z1U

FCCID:Z52NAS-PD07Z1U ANT

version01 SHENZHENNEOELECTRONICSCO.,LTD DeclarationconcerningAntennaSpecification Itisherebydeclaredthattheproduct ModelNo.: NAS-PD07Z1U FCCID:Z52NAS-PD07Z1U fulfillstherequirementinFCCtestrelatingtotheantennatype. ThedevicespecifiedaboveconfirmstotheFCCrecommendationsforinternalantennatype(s) describedbelow: ModelNo.ofantenna:NAS-PD07Z1U Typeofantenna: Springantenna Gainoftheantenna:2dBi Frequencyrange:908.4MHz,916MHz Themountingoftheantennaisfixedtotheradiomoduleandnootherantennashouldbeused. Companyname:SHENZHENNEOELECTRONICSCO.,LTD Address:East6/FBuilding2,Laobingindustry,BaoanDistrict,Shenzhen City:BaoanDistrict ZIP/Postalcode:N.A. Country:China Place:Shenzhen Date:2021-08-10 Signature:

RF EXPOSURE EVALUATION EUT Specification EUTMotion sensor Model Name Frequency band (Operating) WLAN: 2.412GHz ~ 2.462GHz WLAN: 5.18GHz ~ 5.32GHz / 5.50GHz ~ 5.70GHz WLAN: 5.745GHz ~ 5825GHz Others(908.4MHz, 916MHz) Device categoryPortable (<20cm separation) Mobile (>20cm separation) Others ___ Antenna diversity Single antenna Multiple antennas Tx diversity Rx diversity Tx/Rx diversity Max. output power 68.02dBuV/m (-27.248dBm)(0.002mW) Antenna gain2 dBi Evaluation appliedMPE Evaluation SAR Evaluation Standard Requirement Portable Device According to §15.247(i) and §1.1307b(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the Commission’s guidelines. See KDB 447498 D01 General RF Exposure Guidance V6, section 4.3.1. The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances≤50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)]·[√f(GHz)]≤3.0 for 1-g SAR and≤7.5 for 10-g extremity SAR, 16 where ·f(GHz) is the RF channel transmit frequency in GHz ·Power and distance are rounded to the nearest mW and mm before calculation17 ·The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is≤50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. FCC ID: Z52NAS-PD07Z1U NAS-PD07Z1U FCCID:Z52NAS-WR12Z1U MeasurementResult Channel Frequency (GHz) MaxOutput power (dBm) Maxtune-up tolerance Outputpower (dBm) Max Output power (dBm) MaxOutput power (mW) Calculation Value (Note1) Threshold Value -27.248 -27.398 ± 1 -26.2480.0020.0013.0 EIRP=E-104.8+20logD=68.02-104.8+20log3=-27.248dbm Note1:CalculationValue=[(max.powerofchannel,mW)/(min. testseparationdistance,mm)]·[√f(GHz)]. Foxexample:0.002/5*√0.916=0.001≤3.0 AccordingtoKDB447498D01V6,thresholdatwhichnoSARrequiredis≤3.0for1-gSAR, separationdistanceis5mm,andnosimultaneousSARmeasurementisrequired. TheSARmeasurementisnotnecessary. 0.9160

ReportNo.:18220WC00184601FCCID:Z52NAS-PD07Z1UPage1of39 Code:AB-RF-05-a FCCTESTREPORT ClientName:SHENZHENNEOELECTRONICSCO.,LTD Address: East6/F,Building2LaoBingIndustry,No.44TieZaiRoad, BaoanDistrict,Shenzhen,China ProductName:Motionsensor Date:Aug.10,2021 ShenzhenAnbotekComplianceLaboratoryLimited ReportNo.:18220WC00184601FCCID:Z52NAS-PD07Z1UPage2of39 Code:AB-RF-05-a Contents 1.GeneralInformation ............................................................................................................................................... 4 1.1.ClientInformation ....................................................................................................................................... 4 1.2.DescriptionofDevice(EUT) ..................................................................................................................... 4 1.3.AuxiliaryEquipmentUsedDuringTest ................................................................................................... 5 1.4.DescriptionofTestModes ........................................................................................................................ 5 1.5.ListofChannels .......................................................................................................................................... 5 1.6.DescriptionofTestSetup .......................................................................................................................... 6 1.7.TestEquipmentList .................................................................................................................................... 7 1.8.MeasurementUncertainty ......................................................................................................................... 8 1.9.DescriptionofTestFacility ........................................................................................................................ 8 2.SummaryofTestResults ..................................................................................................................................... 9 3.ConductedEmissionTest ................................................................................................................................... 10 3.1.TestStandardandLimit .......................................................................................................................... 10 3.2.TestSetup .................................................................................................................................................. 10 3.3.TestProcedure .......................................................................................................................................... 10 3.4.TestData .................................................................................................................................................... 10 4.RadiatedEmissionandBandEdge .................................................................................................................. 15 4.1.TestStandardandLimit .......................................................................................................................... 15 4.2.TestSetup .................................................................................................................................................. 15 4.3.TestProcedure .......................................................................................................................................... 17 4.4.TestData .................................................................................................................................................... 18 5.20dBBandwidthTest .......................................................................................................................................... 27 5.1.TestStandardandLimit .......................................................................................................................... 27 5.2.TestSetup .................................................................................................................................................. 27 5.3.TestProcedure .......................................................................................................................................... 27 5.4.TestData .................................................................................................................................................... 27 6.AntennaRequirement ......................................................................................................................................... 29 6.1.TestStandardandRequirement ............................................................................................................ 29 6.2.AntennaConnectedConstruction .......................................................................................................... 29 APPENDIXI--TESTSETUPPHOTOGRAPH ................................................................................................... 30 APPENDIXII--EXTERNALPHOTOGRAPH ..................................................................................................... 32 APPENDIXIII--INTERNALPHOTOGRAPH ..................................................................................................... 36 ReportNo.:18220WC00184601FCCID:Z52NAS-PD07Z1UPage3of39 Code:AB-RF-05-a TESTREPORT Applicant:SHENZHENNEOELECTRONICSCO.,LTD Manufacturer:SHENZHENNEOELECTRONICSCO.,LTD ProductName:Motionsensor ModelNo.: NAS-PD07Z1U TradeMark: NEO Rating(s):Input:DC5V Standard(s): FCCPart15SubpartC,Paragraph15.249 TestMethod(s): ANSIC63.10:2013 ThedevicedescribedaboveistestedbyShenzhenAnbotekComplianceLaboratoryLimitedto determinethemaximumemissionlevelsemanatingfromthedeviceandtheseverelevelsofthedevice canendureanditsperformancecriterion.Themeasurementresultsarecontainedinthistestreportand ShenzhenAnbotekComplianceLaboratoryLimitedisassumedfullofresponsibilityfortheaccuracy andcompletenesso…

Text truncated - open the document above for the full version.

PhotoofPowerLineConductedEmissionTest PhotoofRadiationEmissionTest