ZAT-1312PSIP-1CC1312PSIP

Texas Instruments Inc. 12500 TI Blvd. Dallas, TX 75243 USA +1-214-620-4261 Page 1 of 5 OEM/Integrators Installation Manual Important Notice to OEM integrators 1. This module is limited to OEM installation ONLY. 2. This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). 3. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations 4. For FCC Part 15.31 (h) and (k): The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with Part 15 Subpart B, the host manufacturer is required to show compliance with Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the module's intentional emissions are compliant (i.e. fundamental and out of band emissions). The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in Part 15 Subpart B or emissions are complaint with the transmitter(s) rule(s). Antenna Installation (1) The antenna must be installed such that 20 cm is maintained between the antenna and users, (2) The transmitter module may not be co-located with any other transmitter or antenna. (3) Only antennas of the same type and with equal or less gains as shown below may be used with this module. Other types of antennas and/or higher gain antennas may require additional authorization for operation. Texas Instruments Norway AS Page 2 of 5 Brand Antenna Type Peak Gain (dBi) TI Integrated PCB antenna +2.69 dBi Kaadas Flexi PCB antenna -5.82 dBi Leederson Integrated PCB antenna -4.51 dBi Leederson Integrated PCB antenna -1.83 dBi Leederson Stanced antenna -9.48 dBi Leederson Stanced antenna +0.37 dBi Leederson Integrated PCB antenna -1.74 dBi Pulse External whip antenna +0.90 dBi Johanson Technology Chip antenna -0.50 dBi Johanson Technology Chip antenna +1.00 dBi Pulse Wire antenna +0.80 dBi Table 1 – Antenna Specifications In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC/IC authorization is no longer considered valid and the FCC ID/IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/IC authorization. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Texas Instruments Norway AS Page 3 of 5 - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. CAN ICES-3(B)/ NMB-3(B) Radiation Exposure Statement This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Texas Instruments Norway AS Page 4 of 5 End Product Labeling In order to comply with the CC1312PSIP modular approval for use in Canada and the United States. OEM/Host manufacturers must include the following example label as shown in Figure 5 on their end-product and use…

Text truncated - open the document above for the full version.

TI Confidential – NDA Restrictions CC1312PSIP SimpleLink™ Sub-1-GHz Wireless System-in-Package 1 Features Wireless microcontroller •Powerful 48-MHz Arm ® Cortex ® -M4F processor •352KB flash program memory •256KB of ROM for protocols and library functions •8KB of cache SRAM •80KB of ultra-low leakage SRAM with parity for high-reliability operation •Dynamic multiprotocol manager (DMM) driver •Programmable radio includes support for 2- (G)FSK, 4-(G)FSK, MSK, OOK, IEEE 802.15.4 PHY and MAC •Supports over-the-air upgrade (OTA) Ultra-low power sensor controller •Autonomous MCU with 4KB of SRAM •Sample, store, and process sensor data •Fast wake-up for low-power operation •Software defined peripherals; capacitive touch, flow meter, LCD Low power consumption •MCU consumption: –2.9 mA active mode, CoreMark ® –60 μA/MHz running CoreMark® –0.9 μA standby mode, RTC, 80KB RAM –0.1 μA shutdown mode, wake-up on pin •Ultra low-power sensor controller consumption: –30 μA in 2-MHz mode –808 μA in 24-MHz mode •Radio Consumption: –5.8-mA RX at 868 MHz –28.7-mA TX at +14 dBm at 868 MHz Wireless protocol support •Wi-SUN® •mioty® •Wireless M-Bus •SimpleLink™ TI 15.4-stack •6LoWPAN •Proprietary systems High-performance radio •–119 dBm for 2.5-kbps long-range mode •–108 dBm at 50 kbps, 802.15.4, 868 MHz Regulatory compliance •Pre-certified for: –FCC CFR47 Part 15 •Suitable for systems targeting compliance with: –ETSI EN 300 220 Receiver Cat. 1.5 and 2, EN 303 131, EN 303 204 –ARIB STD-T108 MCU peripherals •Digital peripherals can be routed to 30 GPIOs •Four 32-bit or eight 16-bit general-purpose timers •12-bit ADC, 200 kSamples/s, 8 channels •8-bit DAC •Two comparators •Programmable current source •Two UART, two SSI, I 2 C, I 2 S •Real-time clock (RTC) •Integrated temperature and battery monitor Security enablers •AES 128- and 256-bit cryptographic accelerator •ECC and RSA public key hardware accelerator •SHA2 Accelerator (full suite up to SHA-512) •True random number generator (TRNG) Development tools and software •LP-CC1312PSIP Development Kit •SimpleLink™ CC13xx and CC26xx Software Development Kit (SDK) •SmartRF™ Studio for simple radio configuration •Sensor Controller Studio for building low-power sensing applications •SysConfig system configuration tool Operating range •1.8-V to 3.8-V single supply voltage •–40 to +105°C (+14 dBm PA) All necessary components integrated •48-MHz crystal: RF accuracy ±10 ppm •32-kHz crystal: RTC accuracy ±50 ppm •DC/DC converter components and decoupling capacitors •RF front-end components with 50-Ohm output Package •7-mm × 7-mm MOT (30 GPIOs) •Pin-to-pin compatible with CC2652RSIP and CC2652PSIP •RoHS-compliant package ADVANCE INFORMATION CC1312PSIP SWRS293 – MAY 2023 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. ADVANCE INFORMATION for preproduction products; subject to change without notice. TI Confidential – NDA Restrictions 2 Applications •868 and 902 to 928 MHz ISM and SRD systems 1 with down to 4 kHz of receive bandwidth •Building automation –Building security systems – motion detector, electronic smart lock, door and window sensor, garage door system, gateway –HVAC – thermostat, wireless environmental sensor, HVAC system controller, gateway –Fire safety system – smoke and heat detector, fire alarm control panel (FACP) –Video surveillance – IP network camera –Elevators and escalators – elevator main control panel for elevators and escalators •Grid infrastructure –Smart meters – water meter, gas meter, electricity meter, and heat cost allocators –Grid communications – wireless communications – long-range sensor applications –EV Charging infrastructure – AC charging (pile) station –Other alternative energy – energy harvesting •Industrial transport – asset tracking •Factory automation and control •Medical •Communication equipment –Wired networking – wireless LAN or Wi-Fi access points, edge router 3 Description The SimpleLink ™ CC1312PSIP device is a System-in-Package (SiP) Sub-1 GHz wireless module supporting IEEE 802.15.4, IPv6-enabled smart objects (6LoWPAN), mioty, proprietary systems, including the TI 15.4-Stack. The CC1312PSIP microcontroller (MCU) is based on an Arm ® Cortex ® M4F main processor and optimized for low-power wireless communication and advanced sensing in grid infrastructure, building automation, retail automation and medical applications. The CC1312PSIP has a low sleep current of 0.9 μA with RTC and 80KB RAM retention. In addition to the main Cortex® M4F processor, the device also has an autonomous ultra-low power Sensor Controller CPU with fast wake-up capability. As an example, the sensor controller is capable of 1-Hz ADC sampling at average 1-μA system current. The CC1312PSIP has Low SER (Soft Error Rate) FIT (Failure-in-time) for long operational lifetime. Always-on SRAM parity minimizes risk for corruption due to potential radiation events. Consistent with many customers’ 10 to 15 years or longer life cycle requirements, TI has a product life cycle policy with a commitment to product longevity and continuity of supply including dual sourcing of key components in the SIP. The CC1312PSIP device is part of the SimpleLink™ MCU platform, which consists of Wi-Fi®, Bluetooth® Low Energy, Thread, Zigbee, Wi-SUN®, Amazon Sidewalk, mioty, Sub-1 GHz MCUs, and host MCUs. CC1312PSIP is part of a portfolio that includes pin-compatible 2.4-GHz SIPs for easy adaption of a wireless product to multiple communication standards. The common SimpleLink™CC13xx and CC26xx Software Development Kit (SDK) and SysConfig system configuration tool supports migration between devices in the portfolio. A comprehensive number of software stacks, application examples and SimpleLink ™ Academy training sessions are included in the SDK. For more information, visit wireless connectivity. Device Information PART NUMBER (1) PACKAGEBODY SIZE (…

Text truncated - open the document above for the full version.

Texas Instruments Incorporated 12500 TI Boulevard, DALLAS, Texas, United States 75243 Tel: 2145672462 ; Fax: +4722958546 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Certification designating a U.S. agent for service of process pursuant to Part 2.911(d)(7) To whom it may concern, Texas Instruments Incorporated, Grantee Code ZAT, FRN 0020623971] (“the applicant”) certifies that, as of the date of the filing of application, CT Corporation Systems (“the agent”) is designated as the U.S. agent for the purpose of accepting service of process on behalf of the applicant. The physical U.S. address, email for the designated agent are: Physical U.S. address: The Corporation Trust Company 1209 Orange Street Wilmington, DE 19801 Email [email protected] The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The agent accepts the designation by (the applicant) as the U.S. agent to receive and forward service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. Signed by the Applicant Signed by the Agent (if different from the Applicant) Name: Texas Instruments Incorporated Name: Eric Carlson Title: Product Line Manager, Connectivity Title: Assistant Secretary Email: [email protected] TEL: +4793696595 TEL: 214-979-1172 Date: June 22, 2023 Date: June 22, 2023 DocuSign Envelope ID: 84C3872A-8723-45B5-9998-632DD366339F

Texas Instruments Inc. 12500 TI Boulevard, DALLAS, Texas, United States 75243 Te l : 2145672462 ; Fax: +4722958546 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Date: May 24, 2023 Subject: Certifications concerning “covered” equipment pursuant to Part 2.911(d)(5)(i) and (ii) To whom it may concern, [Texas Instruments Inc.] (“the applicant”) certifies that the equipment [FCC ID: Z AT-1312PSIP-1] for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. [Texas Instruments Inc.] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant [is not] identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, ________________________ Name: Peder Rand Title: Product Line Manager, Connectivity E- mail: [email protected] DocuSign Envelope ID: 558CD76B-8C61-42F3-8EB4-79E7A2B3CE42

September 21, 2021 To: Peder Rand From: Marian Kost Subj: Delegation of Authority Under our corporate policy, all delegations are to be made to positions rather than individuals. Therefore, this delegation applies to you while you hold the position listed and will immediately terminate as to you if you change jobs or leave TI. The delegation will continue to be effective as to any employee assuming the position listed above. Commitment Authorizations Authorization is hereby granted to the employee holding the following position to approve and sign on behalf of Texas Instruments Incorporated all contracts, agreements, bids, quotations, purchase orders and other instruments evidencing commitments of Texas Instruments Incorporated within the usual conduct of his/her organization, limited to the amount shown. You are personally responsible to ensure that you exercise the authority consistent with this document and TI’s corporate procedures. Sub-1 GHz Business Manager $1,000,000 Delegation of Commitment Authorizations You may not re-delegate your authority. You may re-delegate your authority on an “acting for” basis or through issuance of “one shots,” as described in SP&P 11-03-01. Marian Kost Business Unit Manager, Connectivity Texas Instruments Incorporated DocuSign Envelope ID: FD4A24EF-51D5-4269-B549-7865596A09AA

Texas Instruments Incorporated 12500 TI Boulevard, M/S D2000, Dalllas, TX, United States 75243 Te l : 1-469-668-2176 ; Fax: 214-479-5605 Date: May 24, 2023 FCC Laboratory 7435 Oakland Mills Rd Columbia MD 21046 Subject: Request for Confidentiality FCC ID: ZAT-1312PSIP-1 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) from public disclosure indefinitely as confidential information.  Schematic Diagram  Block Diagram  Part List  Operational Description  Tune-up Procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’ s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705.  External Photos  Internal Photos  Test Setup Photos  User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and that information will be available for public review once the grant of equipment authorization is issued. Best Regards, ______________________ Peder Rand [email protected] DocuSign Envelope ID: 558CD76B-8C61-42F3-8EB4-79E7A2B3CE42

Texas Instruments Incorporated 12500 TI Boulevard, M/S F2000, Dalllas, TX, United States 75243 Te l : 1-469-668-2176 ; Fax: 214-479-5605 Date: May 24, 2023 Request for Modular Approval for FCC ID: Z AT-1312PSIP-1 Item Requirements EUT 1. The modular transmitter must have its own RF shielding. The module is equipped with its own sputter shield and cannot be removed by the customer. 2. The modular transmitter must have buffered modulation / data inputs. The module has buffer modulation / data inputs. 3. The modular transmitter must have its own power supply regulation. The module has its own power supply regulation. 4. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per §§ 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b) The requirements of the antenna(s) and spurious emissions have been fulfilled. Please refer to the test report and the integrator instructions of this filing. 5. The modular transmitter must be tested in a stand-alone configuration. The module was tested on a stand-alone evaluation board and it’s not inside of another device during testing 6. The modular transmitter must be labeled with its own FCC ID number. For OEM integration the integration manual contains labeling instructions for the host device per Part 15.212 (vi) as the module is too small to hold it’s the FCC ID on the shield. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. The module approved transmitter complies with all applicable rules and the integration manual contains any specific requirements addressed to the integrator and/or to the end-user of the final end-product. 8. The modular transmitter must comply with any applicable RF exposure requirement. The module complies with the FCC RF exposure requirements for fixed and mobile applications. RF exposure is addressed in the RF exposure exhibit. ______________________ Peder Rand [email protected] DocuSign Envelope ID: 558CD76B-8C61-42F3-8EB4-79E7A2B3CE42

PHOTOGRAPHS OF EUT Report No.: EP341305 TEL : 886-3-327-3456 Page Number : 1 of 4 FAX : 886-3-328-4978 Issue Date : Jun. 29, 2023 Report Version : 01 1. Photograph of the EUT CC1312PSIP (Brand Name: Texas Instruments / Model Name: CC1312PSIP SimpleLink™ Sub-1-GHz Wireless System-in-Package) PHOTOGRAPHS OF EUT Report No.: EP341305 TEL : 886-3-327-3456 Page Number : 2 of 4 FAX : 886-3-328-4978 Issue Date : Jun. 29, 2023 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP341305 TEL : 886-3-327-3456 Page Number : 3 of 4 FAX : 886-3-328-4978 Issue Date : Jun. 29, 2023 Report Version : 01

Label Information The product ID will not be placed on the label because it is too small, and will be placed in the user manual instead. The Module’s dimensions are 6.96 X 6.96 X 1.47 mm, and its weight is 0.182 grams. The user manual is the CC1312PSIP datasheet will be readily available online at ti.com, and will show the label as seen below:

PHOTOGRAPHS OF EUT Report No.: EP341305 TEL : 886-3-327-3456 Page Number : 4 of 4 FAX : 886-3-328-4978 Issue Date : Jun. 29, 2023 Report Version : 01 2. Internal Photograph of the EUT CC1312PSIP (Brand Name: Texas Instruments / Model Name: CC1312PSIP SimpleLink™ Sub-1-GHz Wireless System-in-Package) ─────THE END──── Sub-1GHz Antenna

TEL : 886-3-327-3456 Page : 1 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 28, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA341305 RF EXPOSURE EVALUATION REPORT FCC ID : ZAT-1312PSIP-1 Equipment : CC1312PSIP Brand Name : Texas Instruments Model Name : CC1312PSIP SimpleLink™ Sub-1-GHz Wireless System-in-Package Applicant : Texas Instruments Incorporated 12500 TI BLVD., Dallas, Texas, 75243 Manufacturer : Texas Instruments Incorporated 12500 TI BLVD., Dallas, Texas, 75243 Standard : 47 CFR Part 2.1091 We, SPORTON INTERNATIONAL INC has been evaluated this product in accordance with 47 CFR Part2.1091 and it complies with applicable limit. Sporton Lab is accredited to ISO 17025 by Taiwan Accreditation Foundation (TAF code: 1190) and the FCC designation No. TW1190 under the FCC 2.948(e) by Mutual Recognition Agreement (MRA) in FCC evaluation. The results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. Laboratory, the test report shall not be reproduced except in full. SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) Approved by: Cona Huang / Deputy Manager TEL : 886-3-327-3456 Page : 2 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 28, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA341305 Table of Contents 1. DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ............................................................................. 4 2. MAXIMUM RF AVERAGE OUTPUT POWER AMONG PRODUCTION UNITS ........................................ 4 3. DETERMINATION OF EXEMPTION ........................................................................................................... 5 4. RF EXPOSURE EVALUATION ................................................................................................................... 6 4.1. Standalone assessment .................................................................................................................... 6 TEL : 886-3-327-3456 Page : 3 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 28, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA341305 History of this test report Report No. Version Description Issued Date FA341305 Rev. 01 Initial issue of report Jun. 28, 2023 TEL : 886-3-327-3456 Page : 4 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 28, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA341305 1. Description of Equipment Under Test (EUT) Product Feature & Specification EUT Type CC1312PSIP Brand Name Texas Instruments Model Name CC1312PSIP SimpleLink™ Sub-1-GHz Wireless System-in-Package FCC ID ZAT-1312PSIP-1 Wireless Technology and Frequency Range RFID: 902 MHz-928 MHz Mode RFID: GFSK Reviewed by: Jason Wang Report Producer: Paula Chen Antenna Information Brand Antenna Type Model 915MHz Gain 1 TI Integrated PCB antenna LP-EM-CC1312PSIP antenna +2.69 dBi 2 Kaadas Flexi PCB antenna K1 -5.82 dBi 3 Leederson Integrated PCB antenna L1 -4.51 dBi 4 Leederson Integrated PCB antenna L2 -1.83 dBi 5 Leederson Stanced antenna L3 -9.48 dBi 6 Leederson Stanced antenna L4 +0.37 dBi 7 Leederson Integrated PCB antenna L5 -1.74 dBi 8 Pulse External whip antenna W5017 +0.90 dBi 9 Johanson Technology Chip antenna 0900AT43A0070 -0.50 dBi 10 Johanson Technology Chip antenna 0915AT43A0026 +1.0 dBi 11 Pulse Wire antenna W3113 +0.80 dBi 2. Maximum RF average output power among production units Band Maximum Average Power (dBm) RFID 14 TEL : 886-3-327-3456 Page : 5 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 28, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA341305 3. Determination of exemption Per 1.1307(b)(3), (i) For single RF sources (i.e., any single fixed RF source, mobile device, or portable device, as defined in paragraph (b)(2) of this section): A single RF source is exempt if: (A) The available maximum time-averaged power is no more than 1 mW, regardless of separation distance. This exemption may not be used in conjunction with other exemption criteria other than those in paragraph (b)(3)(ii)(A) of this section. Medical implant devices may only use this exemption and that in paragraph (b)(3)(ii)(A); (B) Or the available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold Pth (mW) described in the following formula. This method shall only be used at separation distances (cm) from 0.5 centimeters to 40 centimeters and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by: (C) Or using Table 1 and the minimum separation distance (R in meters) from the body of a nearby person for the frequency (f in MHz) at which the source operates, the ERP (watts) is no more than the calculated value prescribed for that frequency. For the exemption in Table 1 to apply, R must be at least λ/2π, where λ is the free-space operating wavelength in meters. If the ERP of a single RF source is not easily obtained, then the available maximum time- averaged power may be used in lieu of ERP if the physical dimensions of the radiating structure(s) do not exceed the electrical length of λ/4 or if the antenna gain is less than that of a half-wave dipole (1.64 linear value). Table 1 to § 1.1307(b)(3)(i)(C) - Single RF Sources Subject to Routine Environmental Evaluation TEL : 886-3-327-3456 Page : 6 of 6 FAX : 886-3-328-4978 Issued Date : Jun. 28, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA341305 4. RF Exposure Evaluation 4.1. Standalone assessment General Note: 1. Pi is mean the available maximum time-averaged power or the ERP, whichever is greater, for fixed, mobile, or portable RF source i at a distance between 0.5 cm and 40 cm. 2. Pth is mean the exemption threshold power (Pth) according to the § 1.1307(b)(3)(i)(B) formula for fixed, mobile, or portable RF source i. 3. In this report, use Part1.1307(b)(3)(i)(B) to per…

Text truncated - open the document above for the full version.

Home Hardware R&S®TS8991 OTA (Over The Air) performance test system. Additional RSE (Radiated Spurious Emission) test capability with additional filter/LNA support for spurious emissions measurements. SoftwareR&S®EMC32 measurement software for Automation for EMC compliance and pre-compliance Table of Calibrated InstrumentsSA30 - R&S FSW26 - Due 30th March 2023 Test Site InformationTI Norway, Validation Lab, Hoffsvein 70C, 0377 Oslo Completed Test Dates2nd February 2023 Test PersonnelRichard Wallace Test Setup Photos: Placement of AUT on turn arm in chamber: Receiving antenna in chamber: Home LP-EM-CC1312PSIP 902 MHz915 MHz928 MHz TRP=-103.68131265E-3TRP=-880.12967319E-3TRP=-1.4022013807E+0 MaxEIRP=3.8378104306E+03.84MaxEIRP=2.6865205357E+02.69MaxEIRP=2.1021809249E+02.10 MinEIRP=-23.269187494E+0MinEIRP=-26.749749107E+0MinEIRP=-22.318906496E+0 MaxEIRPTheta=90.000000000E+0MaxEIRPTheta=90.000000000E+0MaxEIRPTheta=90.000000000E+0 MaxEIRPPhi=210.00000000E+0MaxEIRPPhi=210.00000000E+0MaxEIRPPhi=180.00000000E+0 MinEIRPTheta=0.0000000000E+0MinEIRPTheta=0.0000000000E+0MinEIRPTheta=180.00000000E+0 MinEIRPPhi=120.00000000E+0MinEIRPPhi=30.000000000E+0MinEIRPPhi=90.000000000E+0 MinEIRPPos=28.000000000E+0MinEIRPPos=7.0000000000E+0MinEIRPPos=27.000000000E+0 MaxEIRPPos=52.000000000E+0MaxEIRPPos=52.000000000E+0MaxEIRPPos=45.000000000E+0 BackPos=10.000000000E+0BackPos=10.000000000E+0BackPos=3.0000000000E+0 BackPosTheta=90.000000000E+0BackPosTheta=90.000000000E+0BackPosTheta=90.000000000E+0 BackPosPhi=30.000000000E+0BackPosPhi=30.000000000E+0BackPosPhi=0.0000000000E+0 Directivity=3.9414917433E+0Directivity=3.5666502088E+0Directivity=3.5043823056E+0 Total Power (dBm)Total Power (dBm)Total Power (dBm) 0-1.82E+01-1.02E+01-2.84E+009.07E-016.85E-02-2.07E+00-1.65E+010-2.12E+01-1.25E+01-2.75E+003.90E-01-7.05E-01-2.37E+00-1.79E+010-1.98E+01-1.59E+01-3.47E+002.82E-01-7.39E-01-2.91E+00-1.63E+01 30-2.28E+01-1.00E+01-6.48E-019.95E-01-3.53E-01-8.76E-01-2.30E+0130-2.67E+01-1.14E+01-8.33E-015.14E-01-8.59E-01-1.37E+00-2.34E+0130-2.17E+01-1.38E+01-1.62E+003.54E-01-8.44E-01-1.98E+00-1.73E+01 60-2.06E+01-8.45E+001.54E+005.63E-01-2.48E-013.83E-02-1.93E+0160-2.25E+01-9.23E+008.68E-01-4.57E-02-1.06E+00-9.49E-01-2.49E+0160-2.01E+01-1.19E+01-8.28E-02-1.51E-01-1.04E+00-1.70E+00-1.98E+01 90-1.94E+01-7.07E+002.27E+005.16E-01-6.66E-01-2.20E-01-1.61E+0190-2.42E+01-8.46E+001.26E+00-2.04E-01-1.49E+00-1.50E+00-1.86…

Text truncated - open the document above for the full version.