ZKJ-BLEACMA001Bluetooth Low Energy Appliance Control Module

06-15 GE monogram.com Owner’s Manual Precision Cooking Probe JXSOUSV1 For Use With 30” and 36” Induction Cooktop Models: ZHU30RSJSS ZHU36RSJSS ZHU30RDJBB ZHU36RDJBB CHP9530SJSS CHP9536SJSS 49-80776 Printed in the United States Consumer Information Precision Cooking Probe 2 Introduction Thank you for purchasing the new Precision Cooking Probe for use with your GE Café or Monogram Induction Cooktop! This device works in conjunction with your induction cooktop to accurately control the temperature within ±1 degree Fahrenheit. You can select any temperature within the range of 85°F to 200°F. This will enable you to perform such cooking operations as slow cooking, simmering liquids, and even sous vide cooking. Precision cooking has been used by high-end restaurants and steakhouses for decades to achieve precise internal temperatures and consistently cooked proteins and vegetables. When done properly it essentially eliminates the possibility of overcooked foods and locks in juices to guarantee a moist, tender creation every time. The Precision Cooking Probe is designed to work on the largest induction element. For 36” models, this is the center element. For 30” models, this is the rightmost element. When selecting a stockpot, choose one large enough to hold your food. We recommend using a pot at least 4 inches tall with a minimum diameter of 7 inches. If you have any questions, visit our Website at: monogram.com Contents Care and Cleaning Glass Cooktop ...................................................... 19–20 Consumer Services Before You Call for Service .....................................20 Important Phone Numbers ...................................... 7 Model and Serial Number ........................................ 2 Safety Instructions ................................................... 4–5 Warranty .......................................................................... 6 Operating Instructions Cookware Recommendations ....................... 16–17 Features of Your Cooktop ..................................... 8-9 How Induction Cooking Works ..................................15 Kitchen Timer .........................................................12-13 Locking the Cooktop ..................................................12 Setting the Controls............................................ 10–14 Surface Elements ....................................................... 10 Before using your precision cooking probe Read this manual carefully. It is intended to help you operate and maintain your new precision cooking probe properly. Keep it handy for answers to your questions. If you don’t understand something or need more help, there is a list of toll-free on Consumer Service page. OR Visit our Website at: monogram.com Write down the model & serial numbers You’ll find them on a label under the cooktop. Fill out and return the Consumer Product Registration Card that is packed with this product. Before sending in the card, please write the numbers here: Model Number Serial Number Use these numbers in any correspondence or service calls concerning your precision cooking probe. 7” min. 4” min. 3 If you received a damaged precision cooking probe Immediately contact the dealer (or builder) that sold you the precision cooking probe. Save time & money Read this manual. Inside you will find many helpful hints on how to use and maintain your precision cooking probe properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your precision cooking probe. You’ll find many answers to common problems in the Before You Call for Service section. If you review our chart of Troubleshooting Tips first, you may not need to call for service at all. If you need service To obtain service, see the Consumer Services page. We’re proud of our service and want you to be pleased. If for some reason you are not happy with the service you receive, here are some steps to follow for further help. FIRST, contact the people who serviced your accessory. Explain why you are not pleased. In most cases, this will solve the problem. NEXT, if you are still not pleased, write all the GHWDLOV³LQFOXGLQJ\RXUSKRQHQXPEHU³WR Manager, Customer Relations GE Appliances Appliance Park Louisville, KY 40225 Consumer Information Precision Cooking Probe IMPORTANT SAFETY INSTRUCTIONS WARNING! Read all safety instructions before using the product . Failure to follow these instructions may result in fire, electrical shock, serious injury or death. • This device shall only be used for its intended purpose as described in this Owner’s Manual. • Consuming raw or undercooked meats, poultry, seafood, shellfish, or eggs may increase your risk of foodborne illness, especially if you have a medical condition. Consult the guidelines for safe minimum internal cooking temperatures provided by the U.S. Department of Health & Human Services at www.foodsafety.gov. ‡'RQRWOHDYHFKLOGUHQDORQH³FKLOGUHQVKRXOGQRW be left alone or unattended in an area where the appliance is in use. They should never be allowed to climb, sit or stand on any part of the cooktop. • Use of equipment or accessories not included with this kit is prohibited and may compromise the built in protections and safeguards. • Do not use a flammable liquid as a bath fluid; do not use with any non-food products. • Do not operate in Precision Cooking Mode without bath fluid in the cooking vessel. • Periodically check to ensure that the liquid depth is within the acceptable range. Refill bath fluid if it is nearing the probe tip. • Do not touch hot surfaces. Use of an oven mitt when handling probe and cooking vessel is recommended. • Do not allow cooking vessel or any cords to hang over the edge of cooktop or counter. • If the Precision Cooking Probe or Bluetooth ® Module is damaged or malfunctioning, cease use of the device. READ AND SAVE THESE INSTRUCTIONS 4 This device complies with Industry Canada’s license- exempt RSSs. Operatio…

Text truncated - open the document above for the full version.

Serial: X XXXXXXXXXXX Model: 265D1664G008 FCC ID: ZKJ-BLEACMA001 IC: 10229A-BLEACMA001 LABEL SPEC SHEET 26JUNE2015 BLE ACM UNIT: MM DESC: LABEL SPECIFICATION I SCALE: 100%DRAWN BY: PETER BENSEL C O N F I D E N T I A L 20% COOL GREY 1 COOL GREY 7 BLACK Please ref er to further use and care instructions online at geapplianceparts .c om

731 Enterprise Drive Lexington, KY 40510 Telephone: 859-226-1000 Facsimile: 859-226-1040 www.intertek-etlsemko.com Standalone SAR Test Exclusion Calculation 1.1 Test Procedure Per KDB447498 D01 Section 4.3.1 Standalone SAR test exclusion, the following formula was used to determine if the device was excluded from a SAR evaluation: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, 25 where • f(GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation26 • The result is rounded to one decimal place for comparison For Industry Canada, an exemption from routine SAR evaluation is achieved by meeting the exemption limits shown in the table below: 731 Enterprise Drive Lexington, KY 40510 Telephone: 859-226-1000 Facsimile: 859-226-1040 www.intertek-etlsemko.com 1.2 Results: The following were used in the calculation: • Maximum Conducted Output Power = -3.110dbm (0.488mW) • Min Separation Distance = 0mm (5mm used in calculation) • Frequency (GHz) = 2.480 [.488mW / 5mm] x SQRT[2.48GHz] = 1.536 Since 1.536 is less than 3 then the device is excluded from standalone SAR evaluation for the FCC. Since the conducted output power is less than 4mW, the device is also excluded from standalone SAR evaluation for Industry Canada.

This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. EMC Report for GE Digital Energy on the Bluetooth Low Energy Dongle Page 1 of 33 731 Enterprise Drive Lexington, KY 40510 Telephone: 859-226-1000 Facsimile: 859-226-1040 www.intertek-etlsemko.com TEST REPORT Report Number: 102063374LEX-001 Project Number: G102063374 Report Issue Date: 7/7/2015 Model Number: 265D1664G008 Standards: Radios Under Test: CFR Title 47 Part 15 Subpart C Low Energy Bluetooth (BTLE) Tested by: Client: Intertek Testing Services NA, Inc. 731 Enterprise Drive Lexington, KY 40510 GE Digital Energy AP2-315, AP6-1NW Appliance Park Louisville, KY 40225 Report prepared by Report reviewed by Toby Carrier, Technician Bryan Taylor, Team Leader – EMC Intertek Report Number: 102063374LEX-001 Issued: 7/7/2015 EMC Report for GE Digital Energy on the 265D1664G008 Page 2 of 33 TABLE OF CONTENTS 1 Introduction and Conclusion .............................................................................................................. 3 2 Test Summary ...................................................................................................................................... 3 3 Description of Equipment Under Test ............................................................................................... 4 4 Peak Conducted Power ....................................................................................................................... 6 5 Occupied Bandwidth ........................................................................................................................... 9 6 Conducted Spurious Emissions ....................................................................................................... 12 7 Power Spectral Density ..................................................................................................................... 14 8 Radiated Spurious Emissions (Transmitter) ................................................................................... 17 9 Radiated Spurious Emissions (Receiver) ........................................................................................ 22 10 AC Powerline Conducted Emissions ........................................................................................... 26 11 Antenna Requirement per FCC Part 15.203 ................................................................................. 31 12 Measurement Uncertainty.............................................................................................................. 32 13 Revision History ............................................................................................................................. 33 Intertek Report Number: 102063374LEX-001 Issued: 7/7/2015 EMC Report for GE Digital Energy on the 265D1664G008 Page 3 of 33 1 Introduction and Conclusion The tests indicated in section 2 were performed on the product constructed as described in section 3. The remaining test sections are the verbatim text from the actual data sheets used during the investigation. These test sections include the test name, the specified test method, a list of the actual test equipment used, documentation photos, results and raw data. No additions, deviations, or exclusions have been made from the standard(s) unless specifically noted. Based on the results of our investigation, we have concluded the product tested complied with the requirements of the standard(s) indicated. The results obtained in this test report pertain only to the item(s) tested. The INTERTEK-Lexington is located at 731 Enterprise Drive, Lexington Kentucky, 40510. The radiated emission test site is a 10-meter semi-anechoic chamber. The chamber meets the characteristics of CISPR 16-1 and ANSI C63.4. For measurements, a remotely controlled flush-mount metal-top turntable is used to rotate the EUT a full 360 degrees. A remote controlled non-conductive antenna mast is used to scan the antenna height from one to four meters. The test site is listed with the FCC under registration number 485103. The test site is listed with Industry Canada under site number IC 2042M-1. 2 Test Summary Page Test full name FCC Reference IC Reference Result 6 Peak Conducted Power § 15.247(b)(3)(4) RSS-210 (A8.4) Pass 9 Occupied Bandwidth § 15.247(a)(2) RSS-210 (A8.2), RSS-GEN (4.6.1) Pass 12 Conducted Spurious Emissions § 15.247(d) RSS-210 (A8.5) Pass 14 Power Spectral Density § 15.247(e) RSS-210 (A8.2b) Pass 17 Radiated Spurious Emissions (Transmitter) § 15.247(d), § 15.209, and § 15.205 RSS-210 (2.2) (A8.5) Pass 22 Radiated Spurious Emissions (Receiver) § 15.109 RSS-Gen (6.1) Pass 26 Conducted Voltage Emissions on the AC Mains Terminals § 15.107, § 15.207 RSS-Gen (7.2.4) Pass 31 Antenna Requirement per FCC Part 15.203 § 15.203 RSS-Gen (7.1.2) Pass Intertek Report Number: 102063374LEX-001 Issued: 7/7/2015 EMC Report for GE Digital Energy on the 265D1664G008 Page 4 of 33 3 Description of Equipment Under Test Equipment Under Test Manufacturer GE Digital Energy Model Number 265D1664G008 Serial Number DC0001 Receive Date 4/12/2015 Test Start Date 4/12/22015 Test End Date 4/20/2015 Device Receiv…

Text truncated - open the document above for the full version.