ZLZ-PANLINK3Bluetooth module

QF009.02 (2.0) 第 1 页 共 17 页 Page 1 of 17 User Manual Bluetooth module panlink3 Mindray FCC ID: ZLZ-PANLINK3 Shenzhen Mindray Bio-Medical Electronics Co.,Ltd. KF‐JH‐0601‐1.0 第 3 页 共 17 页 Page 3 of 17 Overview of CBB Purpose and scope This article describes the technical specifications and platform deliverables of the panlink3 BLE5.0 Bluetooth module CBB, as a source of follow-up CBB design and verification solutions, and as a reference document for products that use this CBB. This article applies to panlink3 BLE5.0 Bluetooth module CBB and related products using this CBB. Basic information CBB name: panlink3 Technical direction: hardware + software Person in charge of development: Li Linghua Person in charge of maintenance: Du Xulong, Fu Neng Subordinate functional department: Guardianship Product Development Department Composition of CBB Panlink3 BLE5.0 Bluetooth module CBB is a physical CBB composed of Bluetooth module PCBA and built‐in function software. This module is developed based on nordic nRF52840 SOC, supports BLE 5.0 protocol, and is backward compatible with BLE4.2 and BLE4.0 protocols. Panklink3 is integrated into the motherboard or carrier boar d by soldering. The antenna is connected to the I‐pex socket MHF III (Part No. 20367‐001R) on the module via cable; Panlink3 产品主板或载板 KF‐JH‐0601‐1.0 第 4 页 共 17 页 Page 4 of 17 This CBB provides a set of serial port to Bluetooth low energy (BLE) solutions, which consists of Panlink3 PCBA and built‐in software, as well as supporting antennas. component Material coding description Panlink3 051-003800-00 panlink3 Bluetooth module PCBA, built-in firmware Panklink3 RF test software / RF test software, support Bluetooth module constant frequency, etc. Panlink3 Boot software/ Boot, used to support serial port upgrade test software and function software Panklink3 function software / Functional software KF‐JH‐0601‐1.0 第 5 页 共 17 页 Page 5 of 17 1.2 Introduction to applicable scenarios 1.3 Panlink3 is suitable for products such as monitors, lamp bed towers, wearable wireless sensors, etc., and realizes the transmission of device information or patient data within a range of about 10m. Panlink3 can realize the BLE interconnection of Mindray's internal devices, and can also interconnect with third‐party BLE devices. 1.4 Wor king mode Panlink3 networking is very flexible. It can be configured as a BLE master device, or a BLE slave device, or as both a master and slave device. Up to 8 slave devices can be connected simultaneously as a BLE master device, and up to 1 master device can be connected as a sla ve de vice. Panlink3's wireless communication parameter configuration is very flexible. Each Bluetooth connection can be independently configured with different air interface baud rates: 2Mbps, 1Mbps and 125kbps, high baud rate can achieve greater throughput, and low baud rate can achieve longer communication distance. Each Bluetooth connection of Panlink3 can be independen t ly configured with timing parameters and transmit power to adapt to different products' power consumption, communication distance, throughput and immunity requirements. Panlink3 provides a set of default configurations with the best overall performance, reducing the development difficulty of general application requirements. Panlink3 is a low‐power wireless communication module tha t pr ovides three power consumption states: Data throughput mode: Specific power consumption is related to actual throughput, master‐slave identity, and connection parameter configuration. For typical power consumption, see the technical specifications table. Standby mode: Bluetooth stays connected, does not send or receive application data, and the serial port of the hos t c omputer does not perform operations such as querying and sending data. The average power consumption is less than 1mw. Sleep mode: The Bluetooth chip sleeps completely, and the average power consumption is less than 0.1mw. It wakes up through the reset pin and needs to be re‐initialized after e xiting sleep. KF‐JH‐0601‐1.0 第 6 页 共 17 页 Page 6 of 17 CBB Technical Specifications The detailed technical specifications are as follows: Specification Description Specification Description Protocol Standard Support Bluetooth 5 Compatible with Bluetooth low energy 4.0, Bluetooth low energy 4.2 Basic RF specifications Modulation method: GFSK Working frequency: 2402 ~ 2480MHz Channel interval: 2M Baud rate: 2Mbps, 1Mbps, 125kbps Frequency error: absolute value ≤30ppm Output Power 8dBm maximum, Adjustable, minimum -20dBm. Power accuracy ±4dB Receive sensitivity Not weaker than the typical value +3dB. Typical values: -103dBm at 125kbps, -95dBm at 1Mbps, -92dBm at 2Mbps Host computer interface Single power supply 1.75V~3.6V Serial port, the default baud rate is 115200 (the baud rate error is less than ±1%), The baud rate can be reconfigured to: 1M (the baud rate error is less than ±1%). Antenna interface Support external cable antenna, socket type MHF III, model 20369-001E Host computer communication Can communicate with the host computer to realize serial port to BLE data communication; Host computer status query 1. When the Bluetooth connection status changes, actively report to the host computer. 2. Because Bluetooth cannot send and receive data, the time threshold for terminating the link can be set by the host computer; 3. You can query RSSI through the host computer; 4. The firmware version information and mac address can be queried through the host computer. 5. Support test mode, realize the scanning analysis of all Bluetooth channel noise, and realize the high-precision collection of RSSI. Online upgrade Support online upgrade through host computer RF test mode Support RF test mode, you can set Bluetooth in KF‐JH‐0601‐1.0 第 7 页 共 17 页 Page 7 of 17 normal transmission mode and normal reception mode, you can change the Bluetooth working channel, transmit power, datarate Sleep wake-up function Provides three power consumption states: data thr…

Text truncated - open the document above for the full version.

Shenzhen Mindray BIO-Medical electronics Co.,LTD. Date: Jun. 04, 2020 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: ZLZ-PANLINK3 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Schematics Block Diagram Operational Description Schematics.pdf Block Diagram.pdf Operational Description.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Shenzhen Mindray BIO-Medical electronics Co.,LTD. Signature Leo Shao / Manager Typed name and Title

Shenzhen Mindray BIO-Medical electronics Co.,LTD. FCC ID: ZLZ-PANLINK3 POWER OF ATTORNEY Date: Jun. 04, 2020 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on Jun. 03, 2021. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Shenzhen Mindray BIO-Medical electronics Co.,LTD. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Shenzhen Mindray BIO-Medical electronics Co.,LTD. Signature Leo Shao / Manager Typed name and Title

Modular Approval Declaration Letter Shenzhen Mindray BIO-Medical electronics Co.,LTD. Jun. 10, 2020 (Bluetooth module) FCC ID : ZLZ-PANLINK3 is seeking FCC Authorization as a Single Modular transmitter / Single Limited Modular Approval. The EUT meets the requirements for Single Modular approval / Single Limited Modular Approval as detailed in FCC public Notice DA00-1407. Compliance to each of the requirements is described below: Item Modular requirement Yes No 1 The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly; 2 The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal; 3 The module must contain power supply regulation on the module; 4 The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b); 5 The module must demonstrate compliance in a stand-alone configuration; 6 The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements); 7 The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee; 8 The module must comply with RF exposure requirements Client’s signature Leo Shao / Manager Client’s name / title [email protected] / Mindray Building, Keji 12th Road South, High-tech Industrial Park, Nanshan, 518057 Shenzhen,PEOPLE’S REPUBLIC OF CHINA Contact information / address (Shenzhen Mindray Bio-Medical Electronics Co.,Ltd.)

Shenzhen Mindray BIO-Medical electronics Co.,LTD. Date: Jun. 11, 2020 Federal Communications Commission Authorization and Evaluation Division We, Shenzhen Mindray BIO-Medical electronics Co.,LTD. affirm that this module application is only for internal use of our company's products, not for sale to third-party companies. FCC ID: ZLZ-PANLINK3. Sincerely, Shenzhen Mindray BIO-Medical electronics Co.,LTD. Signature Leo Shao / Manager Typed name and Title

Appendix- panlink3-Photos Page 3 of 5 EUT – External View Model panlink3 FCC ID: ZLZ-PANLINK3

panlink3 Label Sample and Location

Appendix- panlink3-Photos Page 4 of 5 EUT – Internal View Model panlink3 FCC ID: ZLZ-PANLINK3 Appendix- panlink3-Photos Page 5 of 5 ======End====== ANT.

Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Page 1 of 9 TEST REPORT Reference No. .................... : WTS19S11080405W002 FCC ID ................................ : ZLZ-PANLINK3 Applicant ............................ : Shenzhen Mindray Bio-Medical Electronics Co.,Ltd. Address .............................. : Mindray Building, Keji 12th Road South, High-tech Industrial Park, Nanshan, 518057 Shenzhen,PEOPLE’S REPUBLIC OF CHINA Manufacturer .................... : The same as above Address .............................. : The same as above Product ............................... : Bluetooth module Model(s). ............................ : panlink3 Brand Name ....................... : Mindray Standards........................... : FCC 1.1307 Date of Receipt sample .... : 2019-11-20 Date of Test ....................... : 2019-11-21 to 2020-02-24 Date of Issue ...................... : 2020-02-25 Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Tel :+86-755-83551033 Fax:+86-755-83552400 Compiled by: Approved by: Ford Wang / Project Engineer Philo Zhong / Manager Reference No.: WTS19S11080405W002 Page 2 of 9 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Test Facility: The test facility has a test site registered with the following organizations: ISED CAB identifier: CN0013. Test Firm Registration No.: 7760A. Waltek Services(Shenzhen) Co., Ltd. Has been registered and fully described in a report filed with the Industry Canada. The acceptance letter from the Industry Canada is maintained in our files. Registration number 7760A, October 15, 2016. FCC Designation No.: CN1201. Test Firm Registration No.: 523476. Waltek Services(Shenzhen) Co., Ltd. EMC Laboratory `has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration number 523476, September 10, 2019. Reference No.: WTS19S11080405W002 Page 3 of 9 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 2 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 CONTENTS ............................................................................................................................................................ 3 3 REVISION HISTORY ............................................................................................................................................ 4 4 GENERAL INFORMATION .................................................................................................................................. 5 4.1 GENERAL DESCRIPTION OF E.U.T. ................................................................................................................ 5 4.2 DETAILS OF E.U.T. ......................................................................................................................................... 5 5 TEST SUMMARY .................................................................................................................................................. 6 6 RF EXPOSURE ...................................................................................................................................................... 7 6.1 REQUIREMENTS ............................................................................................................................................... 7 6.2 THE PROCEDURES / LIMIT ................................................................................................................................ 7 6.3 MPE CALCULATION METHOD ......................................................................................................................... 8 7 PHOTOGRAPHS OF TEST SETUP AND EUT. ............................................................................................... 9 Reference No.: WTS19S11080405W002 Page 4 of 9 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 3 Revision History Test report No. Date of Receipt sample Date of Test Date of Issue Purpose Comment Approved WTS19S11080 405W001 2019-11-20 2019-11-21 to 2020-04- 16 2020-04-17 original - Valid Reference No.: WTS19S11080405W002 Page 5 of 9 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 4 General Information 4.1 General Description of E.U.T. Product: Bluetooth module Model(s): panlink3 Model Description: N/A Bluetooth Version: Bluetooth V5.0 Hardware Version: 1.0 Software Version: 1.0 Highest frequency (Exclude Radio): 32MHz Storage Location: Internal Storage Note: N/A 4.2 Details of E.U.T. Operation Frequency: BLE:2402-2480MHz Max. RF output power: BLE:6.78dBm [manufacturers advertise rated power: 8dBm(±4dBm)] Type of Modulation: BLE:GFSK Antenna installation: BLE: Externally connected antenna Antenna Type: ANT1: FPC dipole; ANT2: FPC PIFA; ANT3: copper pipe dipole; ANT4: FPC dipole; ANT5: PCB PIFA; ANT6: FPC PIFA Antenna Gain: BLE: ANT1: 2.0dBi; ANT2: 1.0dBi; ANT3: 3.53dBi; ANT4: 2.0dBi; ANT5: 1.0dBi; ANT6: 0.64dBi Ratings: DC 1.75~3.6V Reference No.: WTS19S11080405W002 Page 6 of 9 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 5 Test Summary Test Items Test Requirement Result Maximum Permissible Exposure (Exposure of Humans to RF Fields) 1.1307(b)(1) PASS Reference No.: WTS19S11080405W002 Page 7 of 9 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 6 RF Exposure Test Requirement: FCC Part 1.1307 Test Mode: The EUT work in te…

Text truncated - open the document above for the full version.

Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Page 1 of 55 TEST REPORT Referen ce No. .................... : WTS19S11080405W001 V1 FCC ID ................................ : ZLZ-PANLINK3 Applicant ............................ : Shenzhen Mindray Bio-Medical Electronics Co.,Ltd. Address .............................. : Mindray Building, Keji 12th Road South, High-tech Industrial Pa rk, Nan shan, 518057 Shenzhen,PEOPLE’S REPUBLIC OF CHINA Manufacturer .................... : The same as above Address .............................. : The same as above Product ............................... : Bluetooth module Model(s). ............................ : panlink3 Brand Name ....................... : Mindray Standards........................... : FCC CFR47 Part 15.247:2018 Date of Receipt sample .... : 2019-11-20 Date of Test ....................... : 2019-11-21 to 2020-04-16 Date of Issue ...................... : 2020-06-12 Test Result ......................... : Pass Remarks: The re sults shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. Address: 1/F., Fukangtai Building, West Baima Road, Songgang Street, Baoan District, Shenzhen, Guangdong, China Tel :+86-755-83551033 Fax:+86-755-83552400 Compiled by: Approved by: Ford Wang / Project Engineer Philo Zhong / Manager Reference No.: WTS19S11080405W001 V1 Page 2 of 55 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 2 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 CONTENTS ............................................................................................................................................................ 2 3 REVISION HISTORY ............................................................................................................................................ 3 4 GENERAL INFORMATION .................................................................................................................................. 4 4.1 GENERAL DESCRIPTION OF E.U.T. ................................................................................................................ 4 4.2 DETAILS OF E.U.T. ......................................................................................................................................... 4 4.3 CHANNEL LIST ................................................................................................................................................. 5 4.4 TEST MODE ..................................................................................................................................................... 6 4.5 TEST FACILITY ................................................................................................................................................. 6 5 TEST SUMMARY .................................................................................................................................................. 7 6 EQUIPMENT USED DURING TEST .................................................................................................................. 8 6.1 EQUIPMENTS LIST ........................................................................................................................................... 8 6.2 DESCRIPTION OF SUPPORT UNITS ................................................................................................................. 9 6.3 MEASUREMENT UNCERTAINTY ....................................................................................................................... 9 6.4 TEST EQUIPMENT CALIBRATION ..................................................................................................................... 9 7 RADIATED EMISSIONS..................................................................................................................................... 10 7.1 EUT OPERATION ........................................................................................................................................... 10 7.2 TEST SETUP .................................................................................................................................................. 11 7.3 SPECTRUM ANALYZER SETUP ...................................................................................................................... 12 7.4 TEST PROCEDURE ........................................................................................................................................ 13 7.5 CORRECTED AMPLITUDE & MARGIN CALCULATION ..................................................................................... 13 7.6 SUMMARY OF TEST RESULTS ....................................................................................................................... 14 8 CONDUCTED SPURIOUS EMISSIONS .......................................................................................................... 34 8.1 TEST PROCEDURE ........................................................................................................................................ 34 8.2 TEST RESULT ................................................................................................................................................ 35 9 BAND EDGE MEASUREMENT ........................................................................................................................ 39 9.1 TEST PRODUCE ............................................................................................................................................. 39 9.2 TEST RESULT ...............................................................…

Text truncated - open the document above for the full version.

Appendix- panlink3-Photos Page 1 of 5 Photographs –Constructional Details BLE Setup photo Model panlink3 FCC ID: ZLZ-PANLINK3 Photograph - Spurious Emissions Radiated Test Setup Below 30MHz Test Site 2# For 30MHz-1000MHz Test Site 2# Appendix- panlink3-Photos Page 2 of 5 For Above 1GHz Test Site 1#