ZOWPMAD6050SOUNDCHUCK WIRELESS SPORT SPEAKER

Quick Start Guide Step 1 Press and hold the power button for 2 secs.to turn on the speaker. The speaker is automatically in Bluetooth search mode when it's turned on. Search the speaker's Bluetooth name "SOUNDCHUCK"by your phone,connect it . Play the music on your phone Step 2Step 3 USER MANUAL Connectivity Operating instruction 1)Make sure your mobile phone or other Bluetooth device support Bluetooth 3.0, 2.1 or 2.0 (A2DP) 2)Make sure the distance between mobile phone and speaker is within 5m (the oretical value: 10m) 3)Press and hold the button for 2 seconds for turning on speaker, LED indicator is fast fleshing in blue. 4)Use your Bluetooth device (like mobile phone, tablet PC) searching speaker “”. (The speaker is available for pairing at any time after power on)Connect to “”, you'll hear a from speaker, or you can see “Paired successfully” message on your mobile, the source switches to Bluetooth source automatically. SOUNDCHUCK SOUNDCHUCK SOUNDCHUCKprompt tone 5)Play music in your Bluetooth device (like mobile phone, tablet PC), and enjoy the music. 1)Insert the 2 in1 cable's Micro USB side to the speaker's Micro USB jack, and the 3.5mm plug into your device. 2)Play music on your device 1)When there is an incoming call, you can press shortly the button to pick up the call. 2)You can hang up by pressing shortly the button when you finished the call. 3)If you want to reject the incoming call, press and hold the button. 1)Please ensure your music source device support Bluetooth 3.0, 2.0 or 2.1 (A2DP protocol), otherwise, the speaker can't support pairing 2)As per Bluetooth protocol, Bluetooth devices only support one to one paring, please make sure no other device is connected to your speaker, youh ave to disconnect it or button before using other device to search the ; 3)Please make sure the distance between the Bluetooth device and the speaker is not over 5m. Normally, the Bluetooth only supports maximum 10m wireless connections; If the Bluetooth reception is poor, please remove any obstacle front of the speaker or move the Bluetooth device closer to the speaker. 4)For some Bluetooth devices, the Bluetooth connection may be d eactivated automatically as a power-saving feature if power is low, please make sure your device with enough power. 5)The Bluetooth connection will be interrupted by other wireless signal,s uch as Wi-Fi router or 2.4G wireless phones. Pls. make sure not too many wireless devices close to your speaker and mobile phone. press and holdfor 2 seconds SOUNDCHUCK Connect to your Bluetooth devices Troubleshooting Answer incoming call through SOUNDCHUCK Connect by 2 in 1 Cable Bluetooth device PUMA...... PS: You can press and hold the Plus button for 2 secs.to refresh the Bluetooth. Bluetooth PC MP3 Tablet Smart phone Laptop Micro USB To speaker 3.5mm plug to audio source devices 1 2 3 4 5 6 7 8 9 1:LED 1 2:Passive 3:Speaker 4:Plus button 5:Power button 6:Minus button 7:Microphone 8:Micro USB jack 9:LED 2 radiator driver 1.LED indicator 1 -Fast flash in blue: Bluetooth searching -Solid in blue: Bluetooth device connected 2.Passive radiator -Enhance the Bass 3.Speaker driver 4. Button -Press to turn up the Volume -Press and hold for 2 seconds to disconnect current Bluetooth device, search for pairing 5. Button -Press and hold for 2 seconds to turn on the speaker -Press and hold for 2 seconds to turn off the speaker -Press to answer a phone call,press again to end the call 6. Button -Press to turn down the Volume -Press and hold for 2 seconds to reject an incoming call 7.Microphone 8.Micro USB jack: insert the 2 in 1 cable, for charging and Audio input 9.LED indicator 2 -Slow flash in red: in charging -Solid in red: battery is fully charged SOUNDCHUCK SOUNDCHUCK While SOUNDCHUCK is connected by cable, the Bluetooth mode will stop automatically. And you can only control Volume through your device. Once you pull out the cable from SOUNDCHUCK, it will switch back to Bluetooth mode. If one device is paired with SOUNDCHUCK already, and when another device needs to pair, Press and hold button for 2 seconds on speaker to cancel the first pairing, and to search all available Bluetooth device. After press and hold button turns fast flashing in blue, it's under searching and re-pairing status. (SOUNDCHUCK will automatically connect to the device, which used to connect with SOUNDCHUCK.) " SOUNDCHUCK" WIRELESS SPORT SPEAKER PMAD6050 Quick Start Guide This will get your music playing. FCC Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Safety a.CAUTION:Danger of explosio…

Text truncated - open the document above for the full version.

Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: August 08, 2013 SUBJECT: FCC Application for (FCC ID:ZOWPMAD6050 ) To Whom It May Concern: I, the undersigned, hereby attest to the fact that I will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. I understand the following FCC requirements: 1.Devices subject to the DoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage: https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the "accredited" option to search for FCC recognized accredited test firms.) 2.Test facilities located in countries, where the U.S. does not have an operational Telcom MRA are not recognized by the FCC to test for the DoC procedure. 3.Pt 2.1077 contains the list of information that must be included in the Declaration of Conformity, which must be supplied with each product sold. The DoC compliance info shall be included in the User’s Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(c)(2), the responsible party is either the Manufacturer or if the product is imported the Importer . Regards, Signature: Jiangming/ Engineer: Applicant: SHENZHEN 3NOD ELECTRONICS CO., LTD. Address: 3NOD High-Tech Park 15# Zhongfu Road Tangxiayong Village, Industrial Zone Songgang Town, Baoan District, Shenzhen City, China

SHENZHEN 3NOD ELECTRONICS CO., LTD. Date: August 08, 2013 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: ZOWPMAD6050 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Schematics Block Diagram Operational Description SCH.pdf BlockDiagram.pdf CircuitDescription.pdf The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, 3NOD High-tech Park 15#, Zhongfu Road, Tangxiayong Industrial Zone, Songgang Town, Baoan District,Shenzhen City, China ................................................................................. Signature Jiangming/ Engineer ................................................................................. Typed name and Title

SHENZHEN 3NOD ELECTRONICS CO., LTD. FCC ID: ZOWPMAD6050 POWER OF ATTORNEY Date: August 08, 2013 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Services (ShenZhen) Co., Ltd. (Philo Zhong) on our behalf shall have the same effect as acts of our own. This authorization expires on August 07, 2014. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, SHENZHEN 3NOD ELECTRONICS CO., LTD., are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, ................................................................................. Signature Jiangming/ Engineer ................................................................................. Typed name and Title

Reference No.: WTD13S0705391E Page 68 of 76 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 19 Photographs - Constructional Details 19.1 EUT – External View Reference No.: WTD13S0705391E Page 69 of 76 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Reference No.: WTD13S0705391E Page 70 of 76 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn

FCC Label Location for model: PMAD6050 The Label must not be a stick-on paper. The Label on these products must be permanently affixed to the product and readily visible at the time of purchase and must last the expected lifetime of the equipment not be readily detachable. FCC ID: ZOWPMAD6050

FCC Label FCC Label Sample for model: PMAD6050 FCC ID: ZOWPMAD6050 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Reference No.: WTD13S0705391E Page 71 of 76 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 19.2 EUT – Internal View Reference No.: WTD13S0705391E Page 72 of 76 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Reference No.: WTD13S0705391E Page 73 of 76 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn RF MODULE Reference No.: WTD13S0705391E Page 74 of 76 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn Reference No.: WTD13S0705391E Page 75 of 76 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 19.3 EUT – RF ModuleView RF Antenna Reference No.: WTD13S0705391E Page 76 of 76 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn ==End of test report==

Reference No.: WTD13S0705391E Page 1 of 87 FCC TEST REPORT Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn FCC ID : ZOWPMAD6050 Applicant : SHENZHEN 3NOD ELECTRONICS CO., LTD. Address : 3NOD High-Tech Park 15# Zhongfu Road Tangxiayong Village, Industrial Zone Songgang Town, Baoan District, Shenzhen City, China Manufacturer : The same as above Address : The same as above Equipment Under Test (EUT) : Product Name : "SOUNDCHUCK" WIRELESS SPORT SPEAKER Model No. : PMAD6050 Standards : FCC Part15.247:2012 Date of Test : July 12~22, 2013 Date of Issue : July 31, 2013 Test Result : PASS Remark: * The sample described above has been tested to be in compliance with the requirements of ANSI C63.4:2003. The test results have been reviewed and comply with the rules listed above and found to meet their essential requirements. The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the signatures of compiler and approver. Prepared By: Waltek Services (Shenzhen) Co., Ltd. 1/F, Fukangtai Building, West Baima Rd., Songgang Street, Baoan District, Shenzhen 518105, China Tel: +86-755-83551033 Fax: +86-755-83552400 Compiled by: Approved by: Maikou Zhang / Project Engineer Philo Zhong / Manager Reference No.: WTD13S0705391E Page 2 of 87 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 2 Test Summary Test Items Test Requirement Result Spurious Radiated Emissions 15.205(a) 15.209 15.247(d) PASS Band edge Emissions 15.247(d) PASS Spurious RF Conducted Emissions from out of band 15.247(d) PASS Duty Cycle 15.35 PASS Conducted Emissions 15.207 PASS 20dB Bandwidth 15.215c 15.247(a)(1) PASS Maximum Peak Output Power 15.247(b)(1) PASS Frequency Separation 15.247(a)(1) PASS Number of Hopping Frequency 15.247(a)(1)(iii) PASS Dwell time 15.247(a)(1)(iii) PASS Maximum Permissible Exposure (Exposure of Humans to RF Fields) 1.1307(b)(1) PASS Reference No.: WTD13S0705391E Page 3 of 87 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 3 Contents Page 1 COVER PAGE .......................................................................................................................................... 1 2 TEST SUMMARY................................................................................................................................................... 2 3 CONTENTS............................................................................................................................................................. 3 4 GENERAL INFORMATION.................................................................................................................................. 5 4.1 GENERAL DESCRIPTION OF E.U.T.................................................................................................................. 5 4.2 DETAILS OF E.U.T........................................................................................................................................... 5 4.3 CHANNEL LIST................................................................................................................................................. 5 4.4 DESCRIPTION OF SUPPORT UNITS.................................................................................................................. 5 4.5 TEST FACILITY................................................................................................................................................. 6 4.6 TEST LOCATION............................................................................................................................................... 6 5 EQUIPMENT USED DURING TEST................................................................................................................... 7 5.1 EQUIPMENTS LIST........................................................................................................................................... 7 5.2 MEASUREMENT UNCERTAINTY........................................................................................................................ 7 5.3 TEST EQUIPMENT CALIBRATION..................................................................................................................... 7 6 CONDUCTED EMISSION..................................................................................................................................... 8 6.1 E.U.T. OPERATION.......................................................................................................................................... 8 6.2 EUT SETUP..................................................................................................................................................... 8 6.3 CONDUCTED EMISSION TEST RESULT............................................................................................................ 9 7 SPURIOUS RADIATED EMISSIONS............................................................................................................... 11 7.1 EUT OPERATION :......................................................................................................................................... 11 7.2 TEST SETUP.................................................................................................................................................. 12 7.3 SPECTRUM ANALYZER SETUP...................................................................................................................... 13 7.4 TEST PROCEDURE......................................................................................................................................... 14 7.5 CORRECTED AMPLITUDE & MARGIN CALCULATION..................................................................................... 14 7.6 SUMMARY OF TEST RESULTS..........................................................…

Text truncated - open the document above for the full version.

Reference No.: WTD13S0705391E Page 66 of 75 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn 18 Photographs – Test Setup 18.1 Conducted Emissions 18.2 Radiated Emissions Below 30MHz Reference No.: WTD13S0705391E Page 67 of 75 Waltek Services (Shenzhen) Co.,Ltd. http://www.waltek.com.cn From 30-1000MHz Above 1GHz