ZQ6-GT966Xbluetooth module

AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information i Doc. NO: AMPAK GT966X Evaluation Kits User manual Version 2.0 Revision History Date Revision Content Revised By Version 2011/09/24 Initial released Andy 2.0 AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information i Doc. NO: Contents 1. GT966X evaluation board introduction..................................................................... 1 2. PIN Description........................................................................................................... 3 3 33 3. Federal Communication Commission Interference Statement .............................. 4 AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 1 1. GT966X evaluation board introduction GT966X evaluation board (EVB) likes as figure1. That is designed for Bluetooth 2.1+EDR application. The bottom views like as figure2. It is also designed for TI’s MSP430 and TMX320C5X experimenter board. It is subject to provide a convenient environment for customer’s verification on Bluetooth function. There are controller pins on evaluation board which describes as below. Figure1. Top view of GT966X EVB AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 2 Figure2. Bottom view of GT966X EVB Interface highlights: 1. U4: GT966X SIP module. 2. S1: U.FL connector let RF signal in/out path, which R55 need tie on 0ohm. 3. J10: VBAT： ：： ： 3V3 for main system power path. IO ： ：： ：1V8 for system IO level path. S/M： ：： ：PCM mode (Jump on
PCM slave mode. Jump off
PCM master mode) 4. J1&J2: For TI’s experimenter board IO used. AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 3 2. PIN Description Connector No. Pin Name Def. Dir. Description of Options (Common) J1 1,19 GND Connect to ground 3 HCI_CTS_3V3 I HCI UART clear-to-send 5 SLOW_CLK_3V3 I 32.768-KHz clock in 7 HCI_RX_3V3 I HCI UART data receive 9 HCI_TX_3V3 O HCI UART data transmit others Not connected J2 2 GND Connect to ground 7,9 +3V3 I Connect to +3.3V 8 PCM_OUT_3V3 O PCM data output 10 PCM_IN_3V3 I PCM data input 11 PCM_FSYNC_3V3 I/O PCM frame synch 17 PCM_CLK_3V3 I/O PCM clock 18 HCI_RTS_3V3 O HCI UART request-to-send 19 nSHUTD_3V3 I Shutdown input (active low) others Not connected AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 4 3 33 3. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. AMPAK Technology Inc. www.ampak.com.tw Proprietary & Confidential Information Doc. NO: 5 This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: ZQ6-GT966X”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall incl…

Text truncated - open the document above for the full version.

FCC ID: ZQ6-GT966X Report No. : RF 120801C27 Modular Approval Request Letter Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch September 19, 2012 Dear Application Examiner, AMPAK Technology Inc., It’s a bluetooth module, FCC ID: ZQ6-GT966X, would like to have your authorization as a modular approval. The requirements of section 15.212 of FCC rules have been met and shown on the following statements. 1. “The modular transmitter must have its own RF shielding.”: The radio portion of this module has been shielded, please see exhibition External Photo. 2. “The modular transmitter must have buffered modulation/data inputs.” The EUT has buffered data inputs, it is integrated in chip GT966 3. “The modular transmitter must have its own power supply regulation part no.: GT966 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission, unique antenna connector and photo of antennas are shown in the test report. 5. “The modular transmitter must be tested in a stand-alone configuration”. The EUT is tested in a stand-alone configuration via an extender. Please see section Photographs of Test Configuration in the test report. 6. “The modular transmitter must be labeled with its own FCC ID number.” Please see exhibition Label Sample for the FCC ID of this module. And also in the exhibition Users Manual, there are instructions give to the OEM on how to label the end product. FCC ID: ZQ6-GT966X Report No. : RF 120801C27 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. Detail instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is compliant with all applicable RF exposure requirements. RF Exposure is addressed in the RF exposure exhibition. Please contact me if you have any further questions. Thanks for your attention. Best Regards, signature Gary Chang Assistant Manager Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

Page 3

FCC ID: ZQ6-GT966X Report No.: RF 120801C27 Operational Description This device is a bluetooth SIP module. The transmitter of the EUT is powered by 3.3Vdc. The antenna is PIFA antenna with UFL antenna connector. The other instruction, please have a look at the users manual.

Report No.: SA120801C27 1 of 5 Report Format Version 5.0.0 RF EXPOSURE REPORT REPORT NO.: SA120801C27 MODEL NO.: GT966x series FCC ID: ZQ6-GT966X RECEIVED: Aug. 01, 2012 TESTED: Aug. 08 ~ Aug. 18, 2012 ISSUED: Aug. 21, 2012 APPLICANT: AMPAK Technology Inc. ADDRESS: 3F, No.1 Jen Ai Road, Hsinchu Industrial Park, Hukou, Hsinchu,Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-com pliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by any government agencies. Report No.: SA120801C27 2 of 5 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ................................................................................................. 3 1. CERTIFICATION .............................................................................................................. 4 2. RF EXPOSURE ................................................................................................................ 5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) .......................................... 5 2.2 MPE CALCULATION FORMULA ..................................................................................... 5 2.3 CLASSIFICATION ............................................................................................................ 5 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER ................................... 5 Report No.: SA120801C27 3 of 5 Report Format Version 5.0.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA120801C27 Original release Aug. 21, 2012 Report No.: SA120801C27 4 of 5 Report Format Version 5.0.0 1. CERTIFICATION PRODUCT: bluetooth module MODEL NO.: GT966x series BRAND: Ampak APPLICANT: AMPAK Technology Inc. TESTED: Aug. 08 ~ Aug. 18, 2012 TEST SAMPLE: ENGINEERING SAMPLE STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: GT966x series) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE :Aug. 21, 2012 Andrea Hsia / Specialist APPROVED BY : , DATE :Aug. 21, 2012 Gary Chang / Technical Manager Report No.: SA120801C27 5 of 5 Report Format Version 5.0.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r2) where Pd = power density in mW/cm2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER MAX POWER (dBm) ANTENNA GAIN (dBi) DISTANCE (cm) POWER DENSITY (mW/cm 2 ) LIMIT (mW/cm 2 ) Bluetooth EDR 11.05 1 20 0.0032 1 Bluetooth LE 4.0 2.78 1 20 0.0005 1

Report No.: RF120801C27 1 of 67 Report Format Version 5.0.0 FCC TEST REPORT REPORT NO.: RF120801C27 MODEL NO.: GT966x series FCC ID: ZQ6-GT966X RECEIVED: Aug. 01, 2012 TESTED: Aug. 08 ~ Aug. 18, 2012 ISSUED: Aug. 21, 2012 APPLICANT: AMPAK Technology Inc. ADDRESS: 3F, No.1 Jen Ai Road, Hsinchu Industrial Park, Hukou, Hsinchu,Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the com pliance or non-compliance to the specification This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF120801C27 2 of 67 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD .......................................................................................... 5 1. CERTIFICATION ....................................................................................................... 6 2. SUMMARY OF TEST RESULTS .............................................................................. 7 2.1 MEASUREMENT UNCERTAINTY ........................................................................... 8 3. GENERAL INFORMATION ....................................................................................... 9 3.1 GENERAL DESCRIPTION OF EUT ......................................................................... 9 3.2 DESCRIPTION OF TEST MODES ......................................................................... 10 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL ......................... 11 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ........................................ 14 3.4 DESCRIPTION OF SUPPORT UNITS ................................................................... 15 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST .................................................... 15 4. TEST TYPES AND RESULTS (FOR BLUETOOTH EDR) ...................................... 16 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ................................. 16 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 16 4.1.2 TEST INSTRUMENTS ........................................................................................... 17 4.1.3 TEST PROCEDURES ............................................................................................ 18 4.1.4 DEVIATION FROM TEST STANDARD .................................................................. 18 4.1.5 TEST SETUP ......................................................................................................... 19 4.1.6 EUT OPERATING CONDITIONS ........................................................................... 19 4.1.7 TEST RESULTS ..................................................................................................... 20 4.2 CONDUCTED EMISSION MEASUREMENT ......................................................... 29 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT....................................... 29 4.2.2 TEST INSTRUMENTS ........................................................................................... 29 4.2.3 TEST PROCEDURES ............................................................................................ 30 4.2.4 DEVIATION FROM TEST STANDARD .................................................................. 30 4.2.5 TEST SETUP ......................................................................................................... 31 4.2.6 EUT OPERATING CONDITIONS ........................................................................... 31 4.2.7 TEST RESULTS ..................................................................................................... 32 4.3 NUMBER OF HOPPING FREQUENCY USED ...................................................... 34 4.3.1 LIMIT OF HOPPING FREQUENCY USED ............................................................ 34 4.3.2 TEST SETUP ......................................................................................................... 34 4.3.3 TEST INSTRUMENTS ........................................................................................... 34 4.3.4 TEST PROCEDURES ............................................................................................ 34 4.3.5 DEVIATION FROM TEST STANDARD .................................................................. 34 4.3.6 TEST RESULTS ..................................................................................................... 34 4.4 DWELL TIME ON EACH CHANNEL ...................................................................... 36 4.4.1 LIMIT OF DWEL…

Text truncated - open the document above for the full version.

1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 2 3 RADIATED EMISSION TEST 4