
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
LELO Suzhou Armocon Technology Co./Ltd. Authority to Act as Agent Date: 2011-8-10 American Certification Body, Inc. 6731 Whittier Avenue Suite ClIO McLean, VA 22101 To Whom It May Concern: Intertek Shanghai is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: __....(=20.::....:...:12=----"-9---'-1~O:....t..)__ By: Michael Duff (Print name) Title: Operations Support Manager On behalf of: Suzhou Armocon Technology Co.,Ud. (Company Name) Telephone: +86 (0) 512-62588561 +86 (0) 13915500392 I -Must be signed by applicant contact gi ven for applicant on tIle FCC sile, or by the authoriled agent if an appropriate authorized agenl leIter has been provided. Letters should b placed on appropriate ICllcrhead. 022311 - 6
LELO Suzhou Armocon Technology Co./Ltd. Request for Confidentiality Date: 2011-8-10 Subject: Confidential i ty Request for: __----l-'-': 9...!...7...!...9-"=!.8-,--,A,---,-L=-=E,-,=-L-,=,O:..)...)__( In~s~e'-.!...rt!....!F....::C~C~ID~:~Z,-,-T~5----,L~E=.!:L~O~2,--,-1-"=!.5~02~7~aC!..!n~dC!...:~IC~ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-IOO, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit D Short Term [g] Permanent Block Diagrams D Short Term External Photos D Short Term o Permanent*2 Internal Photos D Short Term [g] Pennanent Operation Description/Theory of Operation D Short Term D Pennanent Parts List & Placement/BOM D Short Term D Permanent Tune-Up Procedure D Short Term [g] Permanent Schematics D Short Term Test Setup Photos D Short Term 0 Permanent* User's Manual *Note: (Insert Explanation as Necessary) Suzhou Armocon Technology CO"Ltd. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject infonnation easily avai lable to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of (specify number of days not to exceed 180i_ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Tenn and Pennanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to Ie. Sincerely, By: Michael Duff (Print name) 2 _ The asterisked items (*) require further justification before pennanent confidentiality wi II be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: "The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting." 3 _ Please refer to http;//acl}cerl.cQm/documenls/misc-docs/Memo-Short-· crm-Vs-tandard-onfidentiality.pdf for complete details. - Must be signed by applicant contact given lor applicant on the fCC site, or by rhe authorized agent if an ap[lropr iate authorized agent letter has been provided. Letters should be placed on appropriate letterhead. 022311 - 6
FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 1 of 3 External Picture FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 2 of 3 FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 3 of 3
FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 1 of 2 FCC ID & IC Label FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 2 of 2 EUT Diameter: 65mm Label Position
FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 1 of 3 Internal Picture FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 2 of 3 FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 3 of 3
FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 1 of 15 EMC TEST REPORT for Intentional Radiator No. SH11071065-001 Applicant : Suzhou Armocon Technology Co.,Ltd. 3-5/F No77 SuHong Middle Road SIP Jiangsu China Manufacturer : Suzhou Armocon Technology Co.,Ltd. 3-5/F No77 SuHong Middle Road SIP Jiangsu China Equipment : Remote Controller Type/Model : LELO Insignia SUMMARY The equipment complies with the requirements according to the following standard(s): 47CFR Part 15 (2009): Radio Frequency Devices ANSIC63.4 (2003): American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz RSS-210 Issue 8 (December 2010): Low-power Licence-exempt Radiocommunication Devices (All Frequency Bands): Category I Equipment RSS-Gen Issue 3 (December 2010): General Requirements and Information for the Certification of Radiocommunication Equipment Date of issue: Aug 12, 2011 Prepared by: Reviewed by: Wakeyou Wang (Project Engineer) Daniel Zhao (Reviewer) FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 2 of 15 Description of Test Facility Name: Intertek Testing Services Ltd. Shanghai ETL Semko Address: Building No.86, 1198 Qinzhou Road(North), Shanghai 200233, P.R. China FCC Registration Number: 236597 IC Assigned Code: 2042B-1 Name of contact: Steve Li Tel: +86 21 64956565 ext. 214 Fax: +86 21 54262335 ext. 214 FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 3 of 15 Content SUMMARY ..........................................................................................................................................................1 DESCRIPTION OF TEST FACILITY..........................................................................................................................2 1. GENERAL INFORMATION.............................................................................................................................4 1.1 Applicant Information ......................................................................................................4 1.2 Identification of the EUT .................................................................................................4 1.3 Technical specification.....................................................................................................4 1.4 Mode of operation during the test / Test peripherals used ..............................................4 2. TEST SPECIFICATION...................................................................................................................................5 2.1 Instrument list...................................................................................................................5 2.2 Test Standard....................................................................................................................5 3. RADIATED EMISSION....................................................................................................................................7 3.1 Test limit...........................................................................................................................7 3.2 Test Configuration ...........................................................................................................7 3.3 Test procedure and test setup ...........................................................................................8 3.4 Test protocol.....................................................................................................................9 4. ASSIGNED BANDWIDTH (20DB BANDWIDTH).............................................................................................10 4.1 Limit ...............................................................................................................................10 4.2 Test Configuration .........................................................................................................10 4.3 Test procedure and test setup .........................................................................................10 4.4 Test protocol...................................................................................................................10 5. POWER LINE CONDUCTED EMISSION.........................................................................................................11 5.1 Limit ...............................................................................................................................11 5.2 Test configuration ..........................................................................................................11 5.3 Test procedure and test set up ........................................................................................12 5.4 Test protocol...................................................................................................................12 6. OCCUPIED BANDWIDTH.............................................................................................................................13 6.1 Test limit.........................................................................................................................13 6.2 Test Configuration .........................................................................................................13 6.3 Test procedure and test setup .........................................................................................13 6.4 Test protocol...................................................................................................................13 7. SPURIOUS EMISSION FOR RECEIVER..........................................................................................................14 7.1 Test limit.........................................................................................................................14 7.2 Test Configuration .........................................................................................................14 7.3 Test procedure and test setu…
Text truncated - open the document above for the full version.
FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 1 of 11 Test Data FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 2 of 11 1. Radiated Emission Horizontal Fundamental emission 30 40 50 60 70 80 90 Level [dBμV/m] 2.3516G 2.37G 2.38G 2.39G 2.4G 2.41G 2.4331G Frequency [Hz] x x x x x x x x x MES ww07278maTHH_red MES ww07278maTHH_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 3 of 11 Restrict band emission 0 10 20 30 40 50 60 70 80 Level [dBμV/m] 2.31G 2.33G 2.34G 2.35G 2.36G 2.37G 2.38G 2.4G Frequency [Hz] x x x x x x x x x x x x x x x x MES ww0728maTHHL_red MES ww0728maTHHL_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 4 of 11 0 10 20 30 40 50 60 70 80 Level [dBμV/m] 2.4835G 2.488G 2.49G 2.492G 2.496G 2.5G Frequency [Hz] x x x x x x x x x x x x x x x x MES ww0728maTHHH_red MES ww0728maTHHH_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 5 of 11 Spurious emission 0 10 20 30 40 50 60 70 80 Level [dBμV/m] 30M 50M 70M 100M 200M 300M 500M 700M 1G Frequency [Hz] x x x x x x x MES ww0725ma_h1_red MES ww0725ma_h1_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 6 of 11 Vertical Fundamental emission 35 40 50 60 70 80 Level [dBμV/m] 2.35G 2.38G 2.4G 2.42G 2.44G 2.46G 2.5G Frequency [Hz] x x x x x x x x x x x x x x x x MES ww07278maTVV_red MES ww07278maTVV_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 7 of 11 Restrict band emission 0 10 20 30 40 50 60 70 80 Level [dBμV/m] 2.31G 2.33G 2.34G 2.35G 2.36G 2.37G 2.38G 2.4G Frequency [Hz] x x x x x x x x x x x x x x x x MES ww0728maTVVL_red MES ww0728maTVVL_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 8 of 11 0 10 20 30 40 50 60 70 80 Level [dBμV/m] 2.4835G 2.488G 2.49G 2.492G 2.496G 2.5G Frequency [Hz] x x x x x x x x x x x x x x x x MES ww0728maTVVH_red MES ww0728maTVVH_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 9 of 11 Spurious emission 0 10 20 30 40 50 60 70 80 Level [dBμV/m] 30M 50M 70M 100M 200M 300M 500M 700M 1G Frequency [Hz] x x x x x x x MES ww0725ma_v1_red MES ww0725ma_v1_pre LIM FCC 15 F 3 QP Field Strength QP FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 10 of 11 2. Assigned bandwidth (20dB bandwidth) FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 11 of 11 3. Occupied bandwidth
FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 1 of 5 Test Setup FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 2 of 5 1. Radiated Emission 30MHz-1000MHz, X axis FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 3 of 5 30MHz-1000MHz, Y axis FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 4 of 5 Higher than 1GHz, X axis FCC ID: ZT5-LELO215027 IC: 9798A-LELO Page 5 of 5 Higher than 1GHz, Y axis
Building No.86, 1198 Qinzhou Road(North) · Shanghai · China
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 2.42 GHz - 2.42 GHz | - |

Handheld Massager
Equipment Class
DTS - Digital Transmission System
Handheld massager
Equipment Class
DTS - Digital Transmission System
Handheld massager
Equipment Class
DTS - Digital Transmission System
Handheld Massager
Equipment Class
DTS - Digital Transmission System
Remoto Controller
Equipment Class
DXX - Part 15 Low Power Communication Device Transmitter