ZYQ-NABIJR-NV5AMobile Internet Device

NABIJR-NV5A Connect the power adaptor in the Nabi Jr using the Micro USB cable. Then plug the power adaptor into un electric outlet *210.00 mm *297.00 mm Important Product Information Guide This Important Product Information Guide contains safety, handling, regulatory, and software license information, as well as the one-year limited warranty for nabi. Important Safety and Handling Information WARNING: Failure to follow these safety instructions could result in fire, electric shock, or other injury or damage to nabi or other property. Carrying and Handling nabi. nabi contains sensitive components. Do not drop, disassemble, open, crush, bend, deform, puncture, shred, microwave, incinerate, paint, or insert foreign objects into nabi. Avoiding Water and Wet Locations. Do not use nabi in rain or other wet locations. Take care not to spill any food or liquid on nabi. In case nabi gets wet, unplug all cables, turn off nabi (press and hold the Power button, and then select OK in the Power Off window) before cleaning, and allow it to dry thoroughly before turning it on again. Do not attempt to dry nabi with an external heat source, such as a microwave oven or hair dryer. A nabi that has been damaged as a result of exposure to liquids is not serviceable and not covered under warranty. Repairing or Modifying nabi. Never attempt to repair or modify nabi yourself. Disassembling nabi may cause damage that is not covered under the warranty. nabi does not contain any user-serviceable parts. Service should only be provided by a Fuhu Authorized Service Provider. If nabi has been in contact with liquids, punctured, or subjected to a severe fall, do not use it until you take it to a Fuhu Authorized Service Provider. For service information, please visit: www.nabitablet.com/support. Battery Replacement. The rechargeable battery in nabi should be replaced only by Fuhu. For more information about battery replacement service, please visit: www.nabitablet.com/support. Charging nabi. To charge nabi, only use the nabi Power Adapter. The nabi Power Adapter may become warm during normal use. Always allow adequate ventilation around the nabi Power Adapter. Do not connect or disconnect the nabi Power Adapter with wet hands. Unplug the nabi Power Adapter if any of the following conditions exist: • The power cord or plug has become frayed or damaged. • The adapter is exposed to rain, liquid, or excessive moisture. • The adapter case has become damaged. • You suspect the adapter needs service or repair. • You want to clean the adapter. Read all safety instructions for any products and accessories before using with nabi. Fuhu is not responsible for the operation of third-party accessories or their compliance with safety and regulatory standards. Avoiding Hearing Damage. Permanent hearing loss may occur if headphones are used at high volume. Set the volume to a safe level. You can adapt over time to a higher volume of sound that may sound normal but can be damaging to your hearing. If you experience ringing in your ears or muffled speech, stop listening and have your hearing checked. The louder the volume, the less time is required before your hearing could be affected. Hearing experts suggest that to protect your hearing: • Limit the amount of time you use earbuds, headphones, speakers, or earpieces at high volume. • Avoid turning up the volume to block out noisy surroundings. • Turn the volume down if you can’t hear people speaking near you. Driving and Riding Safely. Use of nabi alone or with headphones (even if used only in one ear) while driving a vehicle or riding a bicycle is not recommended and is illegal in some areas. Check and obey the laws and regulations on the use of mobile devices like nabi in the areas where you drive or ride. Be careful and attentive while driving or riding a bicycle. If you decide to use nabi while driving, keep in mind the following guidelines: • Give full attention to driving or riding and to the road. Using a mobile device while driving or riding may be distracting. If you find it disruptive or distracting while operating any type of vehicle, riding a bicycle, or performing any activity that requires your full attention, safely pull off the road and park if driving conditions allow. • Do not email, take notes, or perform any other activities that require your attention while driving. Composing or reading emails or jotting down a to-do list takes attention away from your primary responsibility, driving safely. Seizures, Blackouts, and Eyestrain. A small percentage of people may be susceptible to blackouts or seizures (even if they have never had one before) when exposed to flashing lights or light patterns such as when playing games or watching video. If you have experienced seizures or blackouts or have a family history of such occurrences, you should consult a physician before playing games or watching videos on your nabi. Discontinue use of nabi and consult a physician if you experience headaches, blackouts, seizures, convulsion, eye or muscle twitching, loss of awareness, involuntary movement, or disorientation. To reduce risk of headaches, blackouts, seizures, and eyestrain, avoid prolonged use, hold nabi some distance from your eyes, use nabi in a well-lit room, and take frequent breaks. Glass Parts. The outside cover of the nabi screen is made of glass. This glass could break if nabi is dropped on a hard surface or receives a substantial impact. If the glass chips or cracks, do not touch or attempt to remove the broken glass and stop using nabi. Glass cracked due to misuse or abuse is not covered under the warranty. Choking Hazards. nabi contains small parts, which may present a choking hazard to small children. Keep nabi and its accessories away from small children. Repetitive Motion. When you perform repetitive activities such as typing or playing games on nabi, you may experience occasional discomfort in your hands, arms, shoulders, neck, or other parts of your body. Take fre…

Text truncated - open the document above for the full version.

KEEN HIGH HOLDING (HK) LIMITED. Date: 2012-12-05 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD FCC ID: ZYQ-NABIJR-NV5A To Whom It May Concern: This letter is to ascertain that KEEN HIGH HOLDING (HK) LIMITED. Mobile Internet Device, MODEL NO.: NABIJR-NV5A, nabi-Junior has been the units used for conducting FCC compliance testing, the DoC part will be tested by FCC recognized test lab. If you have any question or concerns, pls. contact us. Sincerely, Signature Michael Chang E-mail: : [email protected] Phone: +86(0)755 8830 9222 Fax: +86(0)755 8347 9175 Address : Unit 13, 7/F Technology Park, 18 On Lai Street Shatin New Territories HK

Family models declaration letter. We KEEN HIGH HOLDING (HK) LIMITED. Of Unit 13, 7/F Technology Park, 18 On Lai Street Shatin New Territories HK Declare under our sole responsibility that the product FCC ID: ZYQ‐NABIJR‐NV5A Product: Mobile Internet Device MODEL NO.: NABIJR‐NV5A, nabi‐Junior All models have the same constructions, circuit diagram and PCB layout. Only model name is different. Unless otherwise stated Thanks Sincerely, Signature Michael Chang E‐mail: : [email protected] Phone: +86(0)755 8830 9222 Fax: +86(0)755 8347 9175 Address : Unit 13, 7/F Technology Park, 18 On Lai Street Shatin New Territories HK

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 (2012-12-06) To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, KEEN HIGH HOLDING (HK) LIMITED hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): FCC ID: ZYQ-NABIJR-NV5A (Mobile Internet Device, MODEL NO.: NABIJR-NV5A, nabi-Junior) We affirm that between SIEMIC and KEEN HIGH HOLDING (HK) LIMITED, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Signature Michael Chang E-mail: : [email protected] Phone: +86(0)755 8830 9222 Fax: +86(0)755 8347 9175 Address : Unit 13, 7/F Technology Park, 18 On Lai Street Shatin New Territories HK

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 (2012-12-06) To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: ZYQ-NABIJR-NV5A We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Signature Michael Chang E-mail: : [email protected] Phone: +86(0)755 8830 9222 Fax: +86(0)755 8347 9175 Address : Unit 13, 7/F Technology Park, 18 On Lai Street Shatin New Territories HK

FCC ID: ZYQ-NABIJR-NV5A NABIJR-NV5A

Label Location Proposed Label Location on EUT

WIFI Module Antenna

Page 1 of 67 Report No. RXA1211-1114SAR TESTING No. L2264 OET 65 TEST REPORT Product Name Mobile Internet Device Trademark nabi Model NABIJR-NV5A, nabi-Junior FCC ID ZYQ-NABIJR-NV5A Client KEEN HIGH HOLDING(HK) LIMITED TA Technology (Shanghai) Co., Ltd. TA Technology (Shanghai) Co., Ltd. Test Report Report No. RXA1211-1114SAR Page 2 of 67 GENERAL SUMMARY Product Name Mobile Internet Device Model NABIJR-NV5A, nabi-Junior FCC ID ZYQ-NABIJR-NV5A Report No. RXA1211-1114SAR Client KEEN HIGH HOLDING(HK) LIMITED Manufacturer SAME AS APPLICANT Standard(s) IEEE Std C95.1, 1999: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. SUPPLEMENT C Edition 01-01 to OET BULLETIN 65 Edition 97-01 June 2001 including DA 02-1438, published June 2002: Evaluating Compliance with FCC Guidelines for Human Exposure to Radio frequency Electromagnetic Fields Additional Information for Evaluation Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radio frequency Emissions. KDB 248227 D01 SAR meas for 802 11 a b g v01r02: SAR Measurement Procedures for 802.11a/b/g Transmitters. KDB 447498 D01 Mobile Portable RF Exposure v04: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies KDB 941225 D07 UMPC Mini Tablet Devices v01: SAR Evaluation Procedures for UMPC Mini-Tablet Devices Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 7 of this test report are below limits specified in the relevant standards. General Judgment: Pass (Stamp) Date of issue: December 7 th ,2012 Comment The test result only responds to the measured sample. Approved by Director Revised by SAR Manager Performed by SAR Engineer TA Technology (Shanghai) Co., Ltd. Test Report Report No. RXA1211-1114SAR Page 3 of 67 TABLE OF CONTENT 1. General Information ..................................................................................................................... 5 1.1. Notes of the Test Report.......................................................................................................5 1.2. Testing Laboratory ................................................................................................................ 5 1.3. Applicant Information ............................................................................................................ 6 1.4. Manufacturer Information ...................................................................................................... 6 1.5. Information of EUT................................................................................................................ 7 1.6. The Maximum SAR 1g Values ................................................................................................ 9 1.7. Test Date .............................................................................................................................. 9 2. SAR Measurements System Configuration ................................................................................ 10 2.1. SAR Measurement Set-up .................................................................................................. 10 2.2. DASY5 E-field Probe System ............................................................................................. 11 2.2.1. ES3DV3 Probe Specification ....................................................................................... 11 2.2.2. E-field Probe Calibration .............................................................................................. 12 2.3. Other Test Equipment .........................................................................................................12 2.3.1. Device Holder for Transmitters .................................................................................... 12 2.3.2. Phantom...................................................................................................................... 13 2.4. Scanning Procedure........................................................................................................... 13 2.5. Data Storage and Evaluation .............................................................................................. 15 2.5.1. Data Storage................................................................................................................ 15 2.5.2. Data Evaluation by SEMCAD ...................................................................................... 15 3. Laboratory Environment............................................................................................................. 17 4. Tissue-equivalent Liquid ............................................................................................................ 18 4.1. Tissue-equivalent Liquid Ingredients................................................................................... 18 4.2. Tissue-equivalent Liquid Properties .................................................................................... 19 5. System Check ............................................................................................................................ 20 5.1. Description of System Check .............................................................................................. 20 5.2. System Check Results ........................................................................................................ 22 6. Operational Conditions during Test ............................................................................................ 23 6.1. General Description of Test Procedures............................................................................. 23 6.2. Test Position ....................................................................................................................... 24 7. Test Results ................................................................…

Text truncated - open the document above for the full version.

TRF No：FCC 15.247/A Page 1 of 65 Report No: ES121123200E1 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C REQUIREMENT OF Mobile Internet Device MODEL No.: NABIJR-NV5A, nabi-Junior FCC ID: ZYQ-NABIJR-NV5A Trademark: nabi REPORT NO: ES121123200E1 ISSUE DATE: December 06, 2012 Prepared for KEEN HIGH HOLDING (HK) LIMITED Unit 13, 7/F Technology Park, 18 On Lai street Shatin New Territories HK Prepared by SHENZHEN EMTEK CO., LTD. Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China TEL: 86-755-26954280 FAX: 86-755-26954282 TRF No：FCC 15.247/A Page 3 of 65 Report No: ES121123200E1 Ta b l e o f C o n t e n t s 1. GENERAL INFORMATION ................................................................................................................................ 5 1.1 PRODUCT DESCRIPTION.................................................................................................................................... 5 1.2 RELATED SUBMITTAL(S) / GRANT(S)................................................................................................................. 5 1.3 TEST METHODOLOGY....................................................................................................................................... 6 1.4 SPECIAL ACCESSORIES...................................................................................................................................... 6 1.5 EQUIPMENT MODIFICATIONS............................................................................................................................ 6 1.6 TEST FACILITY.................................................................................................................................................. 6 2. SYSTEM TEST CONFIGURATION ................................................................................................................... 7 2.1 EUT CONFIGURATION....................................................................................................................................... 7 2.2 EUT EXERCISE................................................................................................................................................. 7 2.3 TEST PROCEDURE............................................................................................................................................. 7 2.4 CONFIGURATION OF TESTED SYSTEM............................................................................................................... 7 3. DESCRIPTION OF TEST MODES ..................................................................................................................... 9 4. SUMMARY OF TEST RESULTS....................................................................................................................... 10 5. CONDUCTED EMISSIONS TEST .................................................................................................................... 11 5.1 MEASUREMENT PROCEDURE.......................................................................................................................... 11 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................................. 11 5.3 MEASUREMENT EQUIPMENT USED................................................................................................................. 11 5.4 CONDUCTED EMISSION LIMIT......................................................................................................................... 11 5.5 MEASUREMENT RESULT.................................................................................................................................. 12 5.6 CONDUCTED MEASUREMENT PHOTO.............................................................................................................. 13 6. RADIATED EMISSION TEST ........................................................................................................................... 14 6.1 MEASUREMENT PROCEDURE.......................................................................................................................... 14 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................................. 14 6.3 MEASUREMENT EQUIPMENT USED................................................................................................................. 15 6.4 RADIATED EMISSION LIMIT............................................................................................................................. 15 6.5 MEASUREMENT RESULT.................................................................................................................................. 17 6.6 RADIATED MEASUREMENT PHOTOS................................................................................................................ 35 7. 6DB BANDWIDTH TEST................................................................................................................................... 37 7.1 MEASUREMENT PROCEDURE.......................................................................................................................... 37 7.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................................. 37 7.3 MEASUREMENT EQUIPMENT USED................................................................................................................. 37 7.4 MEASUREMENT RESULTS................................................................................................................................37 8. MAXIMUM PEAK OUTPUT POWER TEST ..................................................................................................44 8.1 MEASUREMENT PROCEDURE.......................................................................................................................... 44 8.2 TEST SET-UP (BL…

Text truncated - open the document above for the full version.

Conducted Measurement Photo Radiated Measurement Photos