ZYQ-WPT005Tablet

1 QUICK START GUIDE w i k i p a d 1 WELCOME TO WIKIPAD. To start using your Wikipad, first turn it on by press- ing and holding the On/Off button for a few seconds. Then follow the onscreen instructions to set up your Wikipad. Learn more. Learn more about Wikipad features at wikipad.com. Contact Support. For the Wikipad User Guide and other important information, visit us at wikipad.com/support. WELCOME 23 PROCESSOR NVIDIA® Tegra® 3 mobile processor with quad-core CPU and 5th battery-saver core High-performance 12-core NVIDIA GPU OPERATING SYSTEM Android 4.1 (Jelly Bean) dISPlAY 7” (diagonal) IPS (1280x800) 16:10 ratio wide-view panel Capacitive multi-touch screen (supports 5-point gesture) Scratch-resistant military-grade glass screen wIRElESS Dual-band WiFi (802.11 a/b/g/n) Bluetooth® STORAGE Internal Memory: 1GB DDR3 Flash Memory: 16GB Micro SD slot: supports up to 32GB CAMERA Front: 2-megapixel SENSORS 3-axis accelerometer e-Compass GPS (including GLONASS) INPUT / OUT- PUT 3.5mm stereo headphone and mic minijack Built-in stereo speakers (2) Built-in microphone Micro-USB data and power Micro-HDMI output bATTERY* / POwER Built-in 4100mAH rechargable lithium-polymer battery Universal AC Adapter (5V, 2A) USER INTERFACE Volume up/down buttons Power button Charging indicator LED dIMENSIONS 195.6 x 125.7 x 10.64mm With Controller: 286.0 x 145.0 x 65.3mm *CAUTION: The battery should only be replaced by a manufacturer approved service facility. Any attempt to remove or replace your battery may damage the product. #FEATURE 17” lCd MUlTI-TOUCH SCREEN 2FRONT-FACING CAMERA 2 1 fROnT vIEWPRODUCT SPECIfICATIOnS 45 REAR vIEW #FEATURE 1STEREO SPEAkERS 11 SIDE vIEWS #FEATURE 1MEMORY CARd COMPARTMENT (MICRO Sd) 1 lefT sIderIghT sIde 67 GETTInG STARTED CHARGING YOUR TABLET WARNING: The battery comes partially charged. You must completely charge the battery before using your tablet for the first time. After the first charge you may use your device while charging. CAUTION: When charging your tablet, make sure to use only the charger that came with your tablet. 1. Plug the micro-USB to USB cable into the power adapter. 2. Plug the other end of the micro-USB to USB cable into the micro-USB port at the bottom of your tablet. 3. Plug the charger into an electrical outlet to start charging the battery. LED INDICATOR The LED Indicator located on the front side of your tablet will notify you of the status of your tablet’s battery. lEd sTATEbATTERY lEvEl (%) GREEN (when connected to charger) approx. 100% REd (when connected to charger) 0% to under 100% INSTALLING A MEMORY CARD Your tablet includes an expandable microSD card slot that allows you to add extra storage. To insert a Memory Card: 1. Open the memory card slot cover. 2. Insert the memory card into the memory card slot. Press the memory card in until it is fully inserted. 3. Close the memory card slot cover. If you need to remove the Sd card: 1. Open the memory card slot cover. 2. Gently press the SD card in and then release. The card will pop out of the slot. SIDE vIEWS #FEATURE 1POwER bUTTON 2VOlUME dOwN 3VOlUME UP TOP sIde BOTTOM sIde 1 2 3 4 5 6 #FEATURE 43.5MM HEAdPHONE/MIC JACk 5HdMI OUTPUT 6MICRO-USb (CHARGING) PORT 89 TROUBLESHOOTInG FORCED REBOOT In the event that your tablet becomes unresponsive, you may try a forced reboot. To force your tablet to reboot: 1. Press and hold the power button for 10 seconds (until the tablet turns off). 2. Press and hold the power button until the tablet turns on. GETTInG STARTED POWERING ON 1. Press and hold the Power key on the top side of your tablet to turn it on. POWERING OFF 1. Press and hold the Power key on the top side of your tablet for several seconds 2. Use the touchscreen to confirm that you want to Power off your tablet. COnnECTIOnS BLUETOOTH® WIRELESS Bluetooth wireless technology allows you to connect your tablet to other Bluetooth enabled devices such as Bluetooth stereo headsets, or Bluetooth keyboards for quick and easy text entry. USB CONNECTION A Micro USB connection allows you to transfer HD video, music, pictures, photos and other media content between your tablet and a computer. Use the USB cable that came with your tablet to make the connection and do the following: Microsoft™ Windows™ XP, Windows Vista, Windows 7, and Windows 8 - On your computer, click Start, and select My Computer. Then drag and drop files from your computer to your tablet. Apple™ Macintosh™ - Use Android File Transfer. (You can download it from http://www.android. com/filetransfer.) HDMI CONNECTION A Micro-HDMI connection allows you to connect your tablet to any HDMI-ready monitor or television. 1011 GAME COnTROLLER CONNECTING YOUR GAME CONTROLLER CAUTION: be sure to insert the tablet gently but firmly into the game controller to prevent damage to the connectors. 1. Slide the tablet into the slot at the top of the controller with the docking port at the bottom. 2. To confirm a positive connection, turn your tablet on by holding down the on/ off button for several seconds and then releasing. 3. When the tablet is powered on and the controller is connected properly, the LED at the bottom center of the controller will glow BLUE. NOTE: The game controller may not function with all applications. IMPORTAnT HEALTH WARnInGS ABOUT PLAyInG vIDEO GAMES Photosensitive Seizures A very small percentage of people may experience a seizure when exposed to certain visual images, including flashing lights or patterns that may appear in video games. Even people who have no history of seizures or epilepsy may have an undiagnosed condition that can cause these “photosensitive epileptic seizures” while watching video games. These seizures may have a variety of symptoms, including lighthead- edness, altered vision, eye or face twitching, jerking or shaking of arms or legs, disorientation, confusion, or momentary loss of aware- ness. Seizures may also cause loss of consciousness or convulsions that can lead to injury from falling down or strik…

Text truncated - open the document above for the full version.

KEEN HIGH HOLDING (HK) LIMITED. Date: 2013-04-07 To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD FCC ID: ZYQ-WPT005 To Whom It May Concern: This letter is to ascertain that KEEN HIGH HOLDING (HK) LIMITED. Tablet, MODEL NO.: WPT005, WP005, WPG005 has been the units used for conducting FCC compliance testing, the DoC part will be tested by FCC recognized test lab. If you have any question or concerns, pls. contact us. Sincerely, Michael Chang / Signature E-mail: : [email protected] Phone: +86(0)755 8830 9222 Fax: +86(0)755 8347 9175 Address : Unit 13, 7/F Technology Park, 18 On Lai Street Shatin New Territories HK

Family models declaration letter. 2013-04-07 We KEEN HIGH HOLDING (HK) LIMITED Of Unit 13, 7/F Technology Park, 18 On Lai street Shatin New Territories HK （address） Declare under our sole responsibility that the product Product: Tablet Model Number ：WPT005, WP005, WPG005 All models have the same constructions, circuit diagram and PCB layout. Only model name is different. Unless otherwise stated Thanks Sincerely, Michael Chang/ Signature E-mail: : [email protected] Phone: +86(0)755 8830 9222 Fax: +86(0)755 8347 9175 Address : Unit 13, 7/F Technology Park, 18 On Lai Street Shatin New Territories HK

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Revision History Reason for Amendment (current / obsolete) From To Approved Date Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012 SCS-F18: Project and Product Certification Representative Authorization Letter Page 2 of 2 Rev 3.0 (2013-04-07) To: SIEMIC, INC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Certification Representative Authorization Letter We, KEEN HIGH HOLDING (HK) LIMITED hereby authorize SIEMIC, INC. to act as a Certification Body for certifying for the following project(s): FCC ID: ZYQ-WPT005 (Tablet, MODEL NO.: WPT005, WP005, WPG005) We affirm that between SIEMIC and KEEN HIGH HOLDING (HK) LIMITED, any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, Michael Chang/ Signature E-mail: : [email protected] Phone: +86(0)755 8830 9222 Fax: +86(0)755 8347 9175 Address : Unit 13, 7/F Technology Park, 18 On Lai Street Shatin New Territories HK

Model: WPT005 Model: WP005 Model: WPG005

WIFI/BT Antenna GPS Antenna WIFI/BT Module

Report No.: RXA1304-0006SAR01R1 Page 1 of 70 TESTING No. L2264 SAR TEST REPORT Product Name Tablet Model WPT005,WP005,WPG005 FCC ID ZYQ-WPT005 Client KEEN HIGH HOLDING(HK) LIMITED Manufacturer KEEN HIGH HOLDING(HK) LIMITED Date of issue May 24, 2013 TA Technology (Shanghai) Co., Ltd. TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1304-0006SAR01R1 Page 2 of 70 GENERAL SUMMARY Reference Standard(s) FCC 47CFR §2.1093 Radiofrequency Radiation Exposure Evaluation: Portable Devices ANSI C95.1, 1992: Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.(IEEE Std C95.1-1991) SUPPLEMENT C Edition 01-01 to OET BULLETIN 65 Edition 97-01 June 2001 including DA 02-1438, published June 2002: Evaluating Compliance with FCC Guidelines for Human Exposure to Radio frequency Electromagnetic Fields Additional Information for Evaluation Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radio frequency Emissions. KDB 865664 D01 SAR measurement 100 MHz to 6 GHz v01 SAR Measurement Requirements for 100 MHz to 6 GHz KDB 447498 D01 Mobile Portable RF Exposure v05: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies KDB 616217 D04 SAR for laptop and tablets v01: SAR Evaluation Considerations for Laptop, Notebook, Netbook and Tablet Computers KDB 248227 D01 SAR meas for 802 11 a b g v01r02: SAR Measurement Procedures for 802.11a/b/g Transmitters. Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 7 of this test report are below limits specified in the relevant standards for the tested bands only. General Judgment: Pass Comment The test result only responds to the measured sample. Approved by Director Revised by SAR Manager Performed by SAR Engineer TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1304-0006SAR01R1 Page 3 of 70 TABLE OF CONTENT 1. General Information ........................................................................................................................ 5 1.1. Notes of the Test Report...................................................................................................................................... 5 1.2. Testing Laboratory................................................................................................................................................ 5 1.3. Applicant Information............................................................................................................................................ 6 1.4. Manufacturer Information ..................................................................................................................................... 6 1.5. Information of EUT ............................................................................................................................................... 7 1.6. The Maximum Reported SAR 1g Values ................................................................................................................ 8 1.7. Test Date .............................................................................................................................................................. 8 2. SAR Measurements System Configuration ..................................................................................... 9 2.1. SAR Measurement Set-up.................................................................................................................................... 9 2.2. DASY5 E-field Probe System ............................................................................................................................. 10 2.2.1. EX3DV4 Probe Specification .......................................................................................... 10 2.2.2. E-field Probe Calibration ..................................................................................................11 2.3. Other Test Equipment ........................................................................................................................................ 11 2.3.1. Device Holder for Transmitters ........................................................................................11 2.3.2. Phantom .........................................................................................................................12 2.4. Scanning Procedure ........................................................................................................................................... 12 2.5. Data Storage and Evaluation.............................................................................................................................. 14 2.5.1. Data Storage...................................................................................................................14 2.5.2. Data Evaluation by SEMCAD ......................................................................................... 14 3. Laboratory Environment................................................................................................................ 16 4. Tissue-equivalent Liquid ............................................................................................................... 17 4.1. Tissue-equivalent Liquid Ingredients .................................................................................................................. 17 4.2. Tissue-equivalent Liquid Properties.................................................................................................................... 17 5. System Check ............................................................................................................................... 18 5.1. Description of System Check ............................................................................................................................. 18 5.2. System Check Results ............................…

Text truncated - open the document above for the full version.

TRF No：FCC 15.247/A TRF No：RSS-210/A Page 1 of 69 Report No ES130319170E2 ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT INTENTIONAL RADIATOR CERTIFICATION TO FCC PART 15 SUBPART C AND CANADIAN RSS 210 ISSUE 8 REQUIREMENTS OF Ta b l e t MODEL No.: WPT005, WP005, WPG005 FCC ID: ZYQ-WPT005 IC ID:10558B-WPT005 Trade Mark: wikipad REPORT NO: ES130319170E2 ISSUE DATE: April 8, 2013 Prepared for KEEN HIGH HOLDING (HK) LIMITED Unit 13, 7/F Technology Park, 18 On Lai street Shatin New Territories HK Prepared by SHENZHEN EMTEK CO., LTD Bldg 69, Majialong Industry Zone, Nanshan District, Shenzhen, Guangdong, China TEL: 86-755-26954280 FAX: 86-755-26954282 TRF No：FCC 15.247/A TRF No：RSS-210/A Page 2 of 69 Report No ES130319170E2 VERIFICATION OF COMPLIANCE Applicant: KEEN HIGH HOLDING (HK) LIMITED Unit 13, 7/F Technology Park, 18 On Lai street Shatin New Territories HK Manufacturer: KEEN HIGH HOLDING (HK) LIMITED Unit 13, 7/F Technology Park, 18 On Lai street Shatin New Territories HK Product Description: Tablet Model Number: WPT005, WP005, WPG005 (Note: all the models are the same, except their model number, we take WPT005 to test.) File Number: ES130319170E2 Date of Test: April 1, 2013 to April 8, 2013 We hereby certify that: The above equipment was tested by SHENZHEN EMTEK CO., LTD. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4 (2009) and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits of FCC Rules Part 15.247 and Canadian RSS 210 ISSUE 8 REQUIREMENTS The test results of this report relate only to the tested sample identified in this report. Date of Test : April 1, 2013 to April 8, 2013 Prepared by : Jessie Hu/Editor Reviewer : King Wang/Supervisor Approve & Authorized Signer : Lisa Wang/Manager TRF No：FCC 15.247/A TRF No：RSS-210/A Page 3 of 69 Report No ES130319170E2 Ta b l e o f C o n t e n t s 1. GENERAL INFORMATION ................................................................................................................................ 5 1.1 PRODUCT DESCRIPTION.................................................................................................................................... 5 1.2 RELATED SUBMITTAL(S) / GRANT(S)................................................................................................................. 5 1.3 TEST METHODOLOGY....................................................................................................................................... 6 1.4 SPECIAL ACCESSORIES...................................................................................................................................... 6 1.5 EQUIPMENT MODIFICATIONS............................................................................................................................ 6 1.6 TEST FACILITY.................................................................................................................................................. 6 2. SYSTEM TEST CONFIGURATION ................................................................................................................... 7 2.1 EUT CONFIGURATION....................................................................................................................................... 7 2.2 EUT EXERCISE................................................................................................................................................. 7 2.3 TEST PROCEDURE............................................................................................................................................. 7 2.4 CONFIGURATION OF TESTED SYSTEM............................................................................................................... 7 3. DESCRIPTION OF TEST MODES ..................................................................................................................... 9 4. SUMMARY OF TEST RESULTS....................................................................................................................... 10 5. CONDUCTED EMISSIONS TEST.................................................................................................................... 11 5.1 MEASUREMENT PROCEDURE.......................................................................................................................... 11 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................................. 11 5.3 MEASUREMENT EQUIPMENT USED................................................................................................................. 11 5.4 CONDUCTED EMISSION LIMIT......................................................................................................................... 11 5.5 MEASUREMENT RESULT.................................................................................................................................. 12 6. RADIATED EMISSION TEST ........................................................................................................................... 13 6.1 MEASUREMENT PROCEDURE.......................................................................................................................... 13 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................................. 13 6.3 MEASUREMENT EQUIPMENT USED................................................................................................................. 14 6.4 RADIATED EMISSION LIMIT............................................................................................................................. 14 6.5 MEASUREMENT RESULT.................................................................................................................................. 16 7. 6DB BANDWIDTH…

Text truncated - open the document above for the full version.

Conducted Measurement Photos: Radiated Measurement Photos: 30MHz-1GHz 1G-18GHz 18G-40GHz