2A22V-QIS114-in-1 Wireless Charging Station-Power bank

FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For Power bank WPT This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body. For Charging station base WPT This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. ISED Statement ‐ English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. ‐ French:Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux CNR exempts de licence d’Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas causer d’interférences. (2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l’appareil. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator & your body. Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 0 cm entre le radiateur et votre corps.

FCC ID: 2A22V-QIS11 External Photos of the EUT FCC ID: 2A22V-QIS11 FCC ID: 2A22V-QIS11 FCC ID: 2A22V-QIS11

Label and Location Size: L: 4.0cm*W: 3.0cm Label and Location FCC ID : 2A22V-QIS11

FCC ID: 2A22V-QIS11 Internal Photos of the EUT FCC ID: 2A22V-QIS11 Phone coil antenna FCC ID: 2A22V-QIS11 FCC ID: 2A22V-QIS11 Apple watch coil antenna

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn FCC RF Exposure Report Reference No. ..................... : FCC ID............................................. : CTA26061601202 2A22V-QIS11 Compiled by ( position+printed name+signature) . : File administrators Zoey Cao Supervised by ( position+printed name+signature) . : Project Engineer Ace Chai Approved by ( position+printed name+signature) . : RF Manager Eric Wang Date of issue .................................... : Jun. 23, 2026 Testing Laboratory Name .............. : Shenzhen CTA Testing Technology Co., Ltd. Address ............................................ : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao‘an District, Shenzhen, China Applicant’s name ............................ : Shenzhen DXR Electronic Technology Co., Limited (Dongguan Branch) Address ............................................ : 4th Floor, #5 Building, #189, Yongji Industrial, Zhuweitian, Fenggang Town, Dongguan China Test specification ........................... : FCC CFR 47 PART 1, § 1.1310 Standard ........................................... : KDB 680106 D01 Wireless Power Transfer v04 Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purpses as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ..................... : 4-in-1 Wireless Charging Station-Power bank Trade Mark ....................................... : MERKURY Manufacturer .................................... : Shenzhen DXR Electronic Technology Co., Limited (Dongguan Branch) Model/Type reference ...................... : MI-QIS11 Modulation Type ............................... : MI-QIS11-101, MI-QIS11-199, MI-QIS11-132, MI-QIS11-XXX( XXX represents different colors) Operation Frequency ........................ : 110KHz-205KHz for Mobile 300KHz-350KHz for Watch Rating ............................................... : Refer to section 2.1 Result ............................................... : PASS Report No.: CTA26061601202 Page 2 of 13 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn T E S T R E P O R T Equipment under Test : 4-in-1 Wireless Charging Station-Power bank Model /Type : MI-QIS11 Listed Models : MI-QIS11-101, MI-QIS11-199, MI-QIS11-132, MI-QIS11-XXX( XXX represents different colors) Model difference : The PCB board, circuit, structure and internal of these models are the same, only model number and colour are different for these model. So the tests were performed on model MI-QIS11 and the test results for the main test model can cover the listed models. Applicant : Shenzhen DXR Electronic Technology Co., Limited (Dongguan Branch) Address : 4th Floor, #5 Building, #189, Yongji Industrial, Zhuweitian, Fenggang Town, Dongguan China Manufacturer : Shenzhen DXR Electronic Technology Co., Limited (Dongguan Branch) Address : 4th Floor, #5 Building, #189, Yongji Industrial, Zhuweitian, Fenggang Town, Dongguan China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA26061601202 Page 3 of 13 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn Contents 1 T E S T S T A N D A R D S ................................................... 4 2 S U M M A R Y .............................................................. 5 2.1 General Remarks 5 2.2 Product Description 5 2.3 Description of the test mode 5 2.4 Special Accessories 6 2.5 Modifications 6 3 T E S T E N V I R O N M E N T ................................................ 7 3.1 Address of the test laboratory 7 3.2 Test Facility 7 3.3 Statement of the measurement uncertainty 7 3.4 Equipments Used during the Test 8 4 T E S T L I M I T ............................................................ 8 4.1 Requirement 8 4.2 Test setup 9 4.3 Test Procedures 10 4.4 Equipment Approval Considerations of KDB 680106 D01v04 10 4.5 Test results 11 4.6 Conclusion 12 5 P H O T O G R A P H S O F T H E T E S T S E T U P ......................... 13 Report No.: CTA26061601202 Page 4 of 13 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn 1 T E S T S T A N D A R D S The tests were performed according to following standards: 680106 D01 Wireless Power Transfer v04: EQUIPMENT AUTHORIZATION OF WIRELESS POWER TRANSFER DEVICES. Report No.: CTA26061601202 Page 5 of 13 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn 2 S U M M A R Y 2.1 General Remarks Date of receipt of test sample : Jun. 12, 2026 Testing commenced on : Jun. 12, 2026 Testing concluded on : Jun. 23, 2026 2.2 Pro…

Text truncated - open the document above for the full version.

1. Antenna Description: Antenna type Loop coil antenna Model MI-QIS11-1 Frequency range 110KHz-205KHz, 300KHz-350KHz Manufacturer Shenzhen DXR Electronic Technology Co., Limited (Dongguan Branch) Address 4th Floor, #5 Building, #189, Yongji Industrial, Zhuweitian, Fenggang Town, Dongguan China ANT Peak Gain 0 dBi 2. Antenna Photo: We statement that All measurements were performed radiated and therefore additional antenna gain documentation is not required.

Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn FCC PART 15 SUBPART C TEST REPORT Report Reference No. ..................... : FCC ID............................................. : CTA26061601201 2A22V-QIS11 Compiled by ( position+printed name+signature) . : File administrators Zoey Cao Supervised by ( position+printed name+signature) . : Project Engineer Ace Chai Approved by ( position+printed name+signature) . : RF Manager Eric Wang Date of issue .................................... : Jun. 23, 2026 Testing Laboratory Name .............. : Shenzhen CTA Testing Technology Co., Ltd. Address............................................ : Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao‘an District, Shenzhen, China Applicant’s name ............................ : Shenzhen DXR Electronic Technology Co., Limited (Dongguan Branch) Address............................................ : 4th Floor, #5 Building, #189, Yongji Industrial, Zhuweitian, Fenggang Town, Dongguan China Test specification ........................... : Standard ........................................... : FCC Rules and Regulations Part 15 Subpart C (Section 15.209), ANSI C63.10: 2020 Shenzhen CTA Testing Technology Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purpses as long as the Shenzhen CTA Testing Technology Co., Ltd. is acknowledged as copyright owner and source of the material. Shenzhen CTA Testing Technology Co., Ltd. takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. Test item description ..................... : 4-in-1 Wireless Charging Station-Power bank Trade Mark ....................................... : MERKURY Manufacturer .................................... : Shenzhen DXR Electronic Technology Co., Limited (Dongguan Branch) Model/Type reference ...................... : MI-QIS11 Listed Models .................................. : MI-QIS11-101, MI-QIS11-199, MI-QIS11-132, MI-QIS11-XXX( XXX represents different colors) Modulation Type ............................... : ASK Operation Frequency ........................ : 110KHz-205KHz for Mobile 300KHz-350KHz for Watch Rating ............................................... : Battery: 3.85V 5000mAh 19.25Wh Input #1(Charging Station Dock):9V1.5A Input #2(USB-C):5V2A, 9V2A Output #1(Phone):5W, 7.5W, 10W Output #2:(USB-C):5V3A, 9V2.2A, 12V1.67A(PD 20W) Output #3:(Apple watch):2W Result ............................................... : PASS Report No.: CTA26061601201 Page 2 of 29 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn T E S T R E P O R T Equipment under Test : 4-in-1 Wireless Charging Station-Power bank Model /Type : MI-QIS11 Listed Models : MI-QIS11-101, MI-QIS11-199, MI-QIS11-132, MI-QIS11-XXX( XXX represents different colors) Model difference : The PCB board, circuit, structure and internal of these models are the same, only model number and colour are different for these model. So the tests were performed on model MI-QIS11 and the test results for the main test model can cover the listed models. Applicant : Shenzhen DXR Electronic Technology Co., Limited (Dongguan Branch) Address : 4th Floor, #5 Building, #189, Yongji Industrial, Zhuweitian, Fenggang Town, Dongguan China Manufacturer : Shenzhen DXR Electronic Technology Co., Limited (Dongguan Branch) Address : 4th Floor, #5 Building, #189, Yongji Industrial, Zhuweitian, Fenggang Town, Dongguan China Test Result: PASS The test report merely corresponds to the test sample. It is not permitted to copy extracts of these test result without the written permission of the test laboratory. Report No.: CTA26061601201 Page 3 of 29 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn Contents 1 T E S T S T A N D A R D S .................................................................. 4 2 S U M M A R Y ............................................................................. 5 2.1 General Remarks 5 2.2 Product Description 5 2.3 Description of the test mode 5 2.4 Special Accessories 6 2.5 Modifications 6 3 T E S T E N V I R O N M E N T ............................................................... 7 3.1 Address of the test laboratory 7 3.2 Test Facility 7 3.3 Environmental conditions 7 3.4 Summary of measurement results 8 3.5 Statement of the measurement uncertainty 8 3.6 Equipments Used during the Test 9 4 T E S T C O N D I T I O N S A N D R E S U L T S ............................................ 11 4.1 AC Power Conducted Emission 11 4.2 Radiated Emission 14 4.3 The 20dB bandwidth 18 4.4 Antenna Requirement 20 5 T E S T S E T U P P H O T O S O F T H E E U T .......................................... 21 6 PH O T O S O F T H E E U T ............................................................. 22 Report No.: CTA26061601201 Page 4 of 29 Shenzhen CTA Testing Technology Co., Ltd. Room 106, Building 1, Yibaolai Industrial Park, Qiaotou Community, Fuhai Street, Bao’an District, Shenzhen, China Tel:+86-755 2322 5875 E-mail:[email protected] Web:http://www.cta-test.cn 1 T E S T S T A N D A R D S The tests were performed according to following standards: FCC Rules and Regulations Part 15 Subpart C (Section 15.207): Conducted limits.…

Text truncated - open the document above for the full version.

FCC ID: 2A22V-QIS11 Test Setup Photos of the EUT