2A323-CW41Wireless Car Charger

Instruction Manual Accessories List Product Introduction LED Ambient Light Status Indication Main Unit × 1 Instruction Manual × 1 Type-C Charging Cable (1m) × 1 Air Vent Clip × 1Nut × 1 Nut LED Ambient Light Aluminum Alloy Heat Sink type-c Port Magnetic Wireless Charging Area for Mobile Phones Refrigeration (On/Off) & LED Ambient Light (On/Off) Button Refrigeration (On/Off): LED Ambient Light (On/Off): Back View Schematic Diagram When Refrigeration is On: The fan keeps running continuously. When Refrigeration is Off: The fan stops running. Clip Mount Ball Joint Air Vent Clip Wireless Car Charger Operation Instructions Product SpecificationsAdapter Selection Frequently Asked Questions (1)Please ensure that your mobile phone supports wireless charging. (2)Please connect to a power source using the original charging cable before use. (3) Please make sure there are no metallic materials, magnetic objects, credit cards or pop sockets between your phone and phone case. Why is this charger not working? Why is fast charging not working? (1)Please use a PD 45W or higher car charger adapter. The maximum power is 25W, and the refrigeration function can be activated. (2) Please connect to a power source with the original charging cable before use. Made in China ModeLED Ambient Light Power-On Standby Charging Fully Charged Foreign Object Detection / Protection Status Ice-blue light stays on continuously Light turns off Ice-blue light stays on continuously Ice-blue light breathes once then switches to standby mode I ce-blue light flashes 5 times then switches to standby mode Over-Temperature / Over-Current Status I ce-blue light flashes 5 times then switches to standby mode 1 3 2 70*78mm Refrigeration Function Description Power-on State: The refrigeration function runs for 5 seconds and then stops. Standby State: The refrigeration function remains inactive. Operating State: The refrigeration function starts automatically when a mobile phone is placed on it for charging. Fully Charged State: The refrigeration function stops automatically.Power-on with Charging Device Connected: The refrigeration function keeps running continuously. Name: Wireless Car Charger Product Dimensions (Bare Unit): 68mm*68mm*45mm Input: 15V⎓3A Operating Frequency: 110-360KHz Mobile Phone Output: 25W (max) Effective Wireless Charging Distance (for Mobile Phones): ≤3mm Conversion Efficiency: 60%-80% Material: ABS + Silicone Long-press the button to turn the refrigeration function on or off; the mode cycles alternately. Short-press the button to turn the LED ambient light on or off; the mode cycles alternately. When using a car charger adapter with an output power of less than 30W, the refrigeration function cannot be activated. When using a PD 30W car charger adapter, the maximum charging power for the mobile phone is 15W, and the refrigeration function can be activated. When using a car charger adapter with PD 45W or higher output power, the maximum charging power for the mobile phone is 25W, and the refrigeration function can be activated. ❶Place the nut into the ball joint, insert the clip mount into the ball joint and tighten it with the nut. ❷Place the air vent clip onto the car air vent blades and tighten to lock it in place. ❸Insert the USB-C charging cable; the ice-blue light will breathe once and then switch to standby mode. Place your iPhone on the wireless charging area for magnetic attachment, and the light will turn off when the device enters charging mode. FCC Warning Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐‐ Reorient or relocate the receiving antenna. ‐‐ Increase the separation between the equipment and receiver. ‐‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐‐ Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co‐located for operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device must accept any interference received, including interference that may cause undesired operation. 70mm 7 8 m m 70mm 7 8 m m

Shenzhen Meskey Technology Co., Ltd 2.911 (d)(5)(i) Equipment Type Attestation v1.2 Section 2.911(d)(5)(i) Certification – Equipment Type Company name: Shenzhen Meskey Technology Co., Ltd Address: Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen, China Product Name: Wireless Car Charger FCC ID: 2A323-CW41 Model(s): CW41, CW40 2.911(d)(5)(i) Equipment Type We, [Shenzhen Meskey Technology Co., Ltd] (“the applicant”) certify that the equipment for which authorization is sought through certification is not:  Prohibited from receiving an equipment authorization pursuant to § 2.903; of the FCC rules.  Identified as an equipment type in the “Covered List” NOTE 1 Yours sincerely, Name: Ivan Zhang Date: Aug. 03, 2026 Title and Company name: Manager; Shenzhen Meskey Technology Co., Ltd NOTE 1 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Shenzhen Meskey Technology Co., Ltd 2.911 (d)(5)(ii) Applicant Attestation v1.2 Section 2.911(d)(5)(ii) Certification – Applicant (Covered List ) Company name: Shenzhen Meskey Technology Co., Ltd Address: Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen, China Product Name: Wireless Car Charger FCC ID: 2A323-CW41 Model(s): CW41, CW40 2.911(d)(5)(ii) Applicant filing We, [Shenzhen Meskey Technology Co., Ltd] (“the applicant”) certify that, as of the date of the filing of the application, the applicant is not identified NOTE 1 on the “Covered List” NOTE 2 , established pursuant to § 1.50002 of this chapter, as an entity producing covered communications equipment. Yours sincerely, Name: Ivan Zhang Date: Aug. 03, 2026 Title and Company name: Manager; Shenzhen Meskey Technology Co., Ltd NOTE 1 Delete option not applicable to this application. NOTE 2 “Covered List”; is the List of Equipment and Services Covered By Section 2 of The Secure Networks Act, available at https://www.fcc.gov/supplychain/coveredlist References; 1) 986446 D01 Covered Equipment v01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2) Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

Shenzhen Meskey Technology Co., Ltd Agent Authorization Company: Shenzhen Meskey Technology Co., Ltd Address: Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen, China Product Name: Wireless Car Charger Model Number(s): CW41, CW40 Product Description: Wireless Car Charger We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Aug. 03, 2026 Name: Ivan Zhang Title: Manager Company: Shenzhen Meskey Technology Co., Ltd

< Shenzhen Meskey Technology Co., Ltd > Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD21046 Date: Aug. 03, 2026 Subject; Request for Long Term Confidentiality FCC ID: 2A323-CW41 To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Ivan Zhang Title: Manager

Model Difference Declaration To Whom It May Concern, We, Shenzhen Meskey Technology Co., Ltd Product name: Wireless Car Charger Trade name: meskey Model name: CW41, CW40 All model’s the function, software and electric circuit are the same, only with a product color and model named different. Test sample model: CW41. Please contact me if you have any question. Name: Ivan Zhang Date: Aug. 03, 2026 Title: Manager Signature of applicant:

Model: CW41 Model: CW41 Model: CW41 Model: CW41

FCC ID LABEL: Label Location: FCC ID: 2A323-CW41 0.4cm 2.8cm

Model: CW41 Model: CW41 Model: CW41 Model: CW41 Coil Antenna Model: CW41 Model: CW41

Page 1 of 15 Report No.: UNIA26071603ER-62 FCC MPE TEST REPORT FCC ID: 2A323-CW41 Sample : Wireless Car Charger Trade Mark : meskey Main Model : CW41 Additional Model : CW40 Report No. : UNIA26071603ER-62 Prepared for Shenzhen Meskey Technology Co., Ltd Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Prepared by Shenzhen United Testing Technology Co., Ltd. D101&D401, No. 107, Kaicheng High-Tech Park, Taoyuan Community, Dalang Sub-District, Longhua District, Shenzhen, Guangdong, China Page 2 of 15 Report No.: UNIA26071603ER-62 TEST RESULT CERTIFICATION Applicant ................................... : Shenzhen Meskey Technology Co., Ltd Address ....................................... : Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Manufacturer ............................. : Shenzhen Meskey Technology Co., Ltd Address ....................................... : Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Product description Product ....................................... : Wireless Car Charger Trade Mark .................................. : meskey Model Name ............................... : CW41, CW40 Standards .................................. : FCC KDB680106 D01 Wireless Power Transfer v04 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of UNI, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test Date (s) of performance of tests ................... : Jul. 16, 2026 ~ Jul. 28, 2026 Date of Issue ................................................ : Jul. 29, 2026 Test Result .................................................... : Pass Edited by: Abe Yang Reviewed by: Kelly Cheng Approved by: Liuze Page 3 of 15 Report No.: UNIA26071603ER-62 Table of Contents Pages 1 TEST SUMMARY 4 1.1 TEST PROCEDURES AND RESULTS 4 1.2 TEST FACILITY 5 1.3 MEASUREMENT UNCERTAINTY 6 1.4 ENVIRONMENTAL CONDITIONS 6 2 GENERAL INFORMATION 7 2.1 GENERAL DESCRIPTION OF EUT 7 2.2 TEST MODE 8 2.3 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL 8 2.4 TEST INSTRUMENTS 8 3 MAXIMUM PERMISSIBLE EXPOSURE 9 3.1 MAXIMUM PERMISSIBLE EXPOSURE 9 3.2 TEST PROCEDURE 10 3.3 TEST SETUP 10 3.4 RESULT OF MAXIMUM PERMISSIBLE EXPOSURE 11 3.5 TEST PHOTO 12 Page 4 of 15 Report No.: UNIA26071603ER-62 1 TEST SUMMARY 1.1 TEST PROCEDURES AND RESULTS FCC KDB680106 D01 Wireless Power Transfer v04 FCC CFR 47 Standard Section Test Item Result Remark FCC CFR 47 part1, 1.1310 KDB680106 D01 v04 Electric Field Strength (E) (V/m) N/A -- Magnetic Field Strength (H) (A/m) PASS -- Note: “N/A” denotes test is not applicable in this Test Report. Compliant with FCC KDB680106 D01 Wireless Power Transfer v04 section 5.2: 1) The power transfer frequency is below 1MHz. Yes, the working frequency is: 110-360kHz . 2) The output power from each transmitting element (e.g., coil) is less than or equal to 15 watts. No, the maximum output power is 25 watts. 3) A client device providing the maximum permitted load is placed in physical contact with the transmitter(i.e. , the surfaces of the transmitter and client device enclosures need to be in physical contact) Yes, the maximum permitted load is placed in physical contact with the transmitter. 4) Only $ 2.1091-Mobile exposure conditions apply (i.e., this provision does not cover $ 2.1093-Portable exposure conditions). Yes, this provision does not cover $ 2.1093-Portable exposure conditions. 5) The H-field strengths, at and beyond 20 cm surrounding the device surface, are demonstrated to be less than 50% of the applicable MPE limit, per KDB 447498, Table 1. These measurements shall be taken along the principal axes of the device, with one axis oriented along the direction of the estimated maximum field strength, and for three points per axis or until a 1/d (inverse distance from the emitter structure) field strength decay is observed. Symmetry considerations may be used for test reduction purposes. The device shall be operated in documented worst-case compliance scenarios(i.e. , the ones that lead to the maximum field components), and while all the radiating structures (e.g., coils or antennas) that by design can simultaneously transmit are energized at their nominal maximum power. Yes, The H-field strengths, at and beyond 20 cm surrounding the device surface, are demonstrated to be less than 50% of the applicable MPE limit ; coils or antennas) that by design can simultaneously transmit are energized at their nominal maximum power. Page 5 of 15 Report No.: UNIA26071603ER-62 6) For systems with more than one radiating structure, the conditions specified in (5) must be met when the system is fully loaded (i.e., clients absorbing maximum power available), and with all the radiating structures operating at maximum power at the same time, as per design conditions. If the design allows one or more radiating structures to be powered at a higher level while other radiating structures are not powered, then those cases must be tested as well. For instance, a device may use three RF coils powered at 5 W, or one coil powered at 15 W: in this case, both scenarios shall be tested. Yes, For systems with more than one radiating structure, the conditions specified in (5) must be met when the system is fully loaded (i.e., clients absorbing maximum power available), and with all the radi…

Text truncated - open the document above for the full version.

产 品 承认书 规格编号 HG2026051501 生效日期 客户名称 产品类型QI2线圈 宏贵料号 43.5*0.6开双槽带孔 客户料号 【 □ 新版发行 , □ 版本修订】 【 本规范含目录共 2页 】 【 RoHS Compliant Parts 】 编制审核批准 彭建基 安福宏贵电子有限公司 江西省吉安市安福县洲湖镇杨梅岭北区新能源产业园2#楼 安福宏贵电子有限公司 联系人：彭建基 电话：13907060771 本承认书在客户收到一星期内，请务必签章返回，逾期视为生产时按此承认书的标准 执行。 【客户核准】 日期: 承认状态： □完全承认 □条件承认 □拒绝承认 批准审核复检检查 说明: √√ 产 品 规 格 书 客户名称客户料号 宏贵料号 43.5*0.6开双槽带孔 规格编号 HG2026051501 版本 01 ♦、外形尺寸 (单位: mm) A43.5 ±0.5 B40.0 ±1.5 C20.5 ±0.5 D20.0 ±0.5 E3.0 ±1 F20.0 ±2 G1.8 ±0.2 H0.6 ±0.1 (2)绕线圈数:11T (1)线径: 0.08*70P丝包自粘铜线 S (3)起尾线是否交叉: 是 (4)线圈包5mm宽高温胶带 (5)线圈与磁片需粘贴居中 (6)线圈中间贴直径20MM厚度1.0MM圆片 ♦、电气特性: 参数规格测试条件 测试仪器 L08±0.3μH100KHz/1V■TH1816B Q>50 min100KHz/1V■TH1816B DCR<70mΩ@ 25°C■CH-502BC 操作温度 -40°C~ 125°C ♦、材料清单: 序号 1 品名材料规格供应商 备注 2 磁片 20*1.0圆片PC95猛锌 3 磁片43.5*0.6 开双槽带孔 PC95猛锌 4 铜线 丝包自粘铜 0.08*70P 线 5 高温胶带5MM 环保胶带 6 锡高温锡条 千岛环保锡 7 胶白胶 环保胶水 编制审核批准 彭建基

Page 1 of 24 Report No.: UNIA26071603ER-61 FCC RADIO TEST REPORT FCC ID: 2A323-CW41 Sample : Wireless Car Charger Trade Mark : meskey Main Model : CW41 Additional Model : CW40 Report No. : UNIA26071603ER-61 Prepared for Shenzhen Meskey Technology Co., Ltd Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Prepared by Shenzhen United Testing Technology Co., Ltd. D101&D401, No. 107, Kaicheng High-Tech Park, Taoyuan Community, Dalang Sub-District, Longhua District, Shenzhen, Guangdong, China Page 2 of 24 Report No.: UNIA26071603ER-61 TEST RESULT CERTIFICATION Applicant ................................... : Shenzhen Meskey Technology Co., Ltd Address ...................................... : Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Manufacturer ............................. : Shenzhen Meskey Technology Co., Ltd Address ...................................... : Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Product description Product ....................................... : Wireless Car Charger Trade Mark ................................. : meskey Model Name ............................... : CW41, CW40 Test Methods ............................. : FCC Rules and Regulations Part 15 Subpart C Section 15.209 ANSI C63.10: 2020 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test Date (s) of performance of tests .................... : Jul. 16, 2026 ~ Jul. 28, 2026 Date of Issue ................................................. : Jul. 29, 2026 Test Result ..................................................... : Pass Edited by: Abe Yang Reviewed by: Kelly Cheng Approved by: Liuze Page 3 of 24 Report No.: UNIA26071603ER-61 Table of Contents Pages 1 TEST SUMMARY 4 1.1 TEST PROCEDURES AND RESULTS 4 1.2 TEST FACILITY 4 1.3 MEASUREMENT UNCERTAINTY 5 2 GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 TEST MODE 7 2.3 TEST SETUP 7 2.4 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL 7 2.5 MEASUREMENT INSTRUMENTS LIST 8 3 CONDUCTED EMISSION 10 3.1 TEST LIMIT 10 3.2 TEST SETUP 10 3.3 TEST PROCEDURE 11 3.4 TEST RESULT 11 4 RADIATED EMISSION 14 4.1 TEST LIMIT 14 4.2 TEST SETUP 16 4.3 TEST PROCEDURE 17 4.4 TEST RESULT 17 5 ANTENNA REQUIREMENT 21 6 PHOTO OF TEST 22 6.1 RADIATED EMISSION 22 6.2 CONDUCTED EMISSION 23 7 EUT Constructional Details 23 Refer to the External Photos and Internal Photos for details. 23 Page 4 of 24 Report No.: UNIA26071603ER-61 1 TEST SUMMARY 1.1 TEST PROCEDURES AND RESULTS Item FCC Rules Description Of Test Result 1 FCC Part 15.207 Conducted Emission Pass 2 FCC Part 15.209(a) Radiated Emission Pass 3 FCC Part 15.203 Antenna Requirement Pass 1.2 TEST FACILITY Test Firm : Shenzhen United Testing Technology Co., Ltd. Address : D101&D401, No. 107, Kaicheng High-Tech Park, Taoyuan Community, Dalang Sub-District, Longhua District, Shenzhen, Guangdong, China The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19.The testing quality system of our laboratory meets with ISO/IEC-17025 requirements. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: A2LA Certificate Number: 4747.01 The EMC Laboratory has been accredited by A2LA, and in compliance with ISO/IEC 17025:2017 General Requirements for testing Laboratories. FCC Registration Number: 674885 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. IC Registration Number: 31584 The EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. Page 5 of 24 Report No.: UNIA26071603ER-61 1.3 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. A. Conducted Measurement: Test Site Method Measurement Frequency Range U, (dB) NOTE UNI ANSI 9KHz ~ 150KHz 2.96 150KHz ~ 30MHz 2.44 B. Radiated Measurement: Test Site Method Measurement Frequency Range U, (dB) NOTE UNI ANSI 9KHz ~ 30MHz 2.50 30MHz ~ 1000MHz 4.80 1000MHz ~ 6000MHz 4.13 Page 6 of 24 Report No.: UNIA26071603ER-61 2 GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Product: Wireless Car Charger Trade Mark: meskey Main Model: CW41 Additional Model: CW40 Model Difference: All model’s the function, software and electric circuit are the same, only with a product color and model named different. Test sample model: CW41 FCC ID: 2A323-CW41 Operation Frequency: 110-360kHz Modulation Type: ASK Wireless Charging Output Power: 25W (max) Antenna Type: Coil Antenna Antenna Gain: 0dBi Battery: N/A Adapter: N/A Power Source: DC 15V by Adapter Page 7 of 24 Report No.: UNIA26071603ER-61 2.2 TEST MODE NO. TEST MODE DESCRIPTION 1 Wireless charging Mode + Full load 2 Wireless charging Mode + Half load 3 Wireless charging Mode + Null load Note: The mode 1 was the worst case and only the data of the worst case record in this report. 2.3 TEST SETUP Operation of EUT during testing: 2.4 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL The EUT has been tested as an independent unit toge…

Text truncated - open the document above for the full version.

Model: CW41 Radiated Emission test Model: CW41 Conducted Emission test MPE Test: Model: CW41 Model: CW41