2A323-W98-MAXTEC 3 in 1 Wireless Charger

Magnetic 3-in-1 Fast Wireless Charging Station with Active Cooling Manual Instruction Illustration Diagram of Product Appearance Wireless magnetic charging area for mobilephone Wirelessc harging area for watch Aluminium alloy cooling fan radiator Wireless charging area for earphone charging box Touch position for refrigeration switch Introduction of Function for Touch-type Refrigeration Switch Refrigeration region of mobilephone end Type-C input port Operation instruction Diagram of angle regulation Indicator status Explanation of refrigeration functions: IndicatorMode Blue light and green light alternatively flashes once , then turns to blue light and lights up for 5 seconds before light off. Switch on Light off Standby Green light turns on for 3 seconds Indicator light has no changes The blue light continues flashing until the abnormal state is removed, and the refrigeration system stops working Charging for earphone charging box Full charge FOD protection of mobilephone end The green light continues flashing until the abnormal state is removed Attention: When the output power of the USB-A adapter or PD adapter is less than 27W, the output power is insufficient and the cooling cannot be switched on. The output power of the mobile phone is 10W. The blue light is constantly on FOD protection of earphone end Refrigeration in progress Cautions FCC Warning Statement Package list: Selection of adaptor Wireless charger x1 Charging cable x1 Product Manual x1 Warning Product parameters 尺寸80*100mm双面印刷，折页，128g铜版纸 Indicator Aluminum alloy support rod Switch on status: Refrigeration stops after 5 seconds of operation Standby status: Refrigeration doesn’t work Operation status: Put on your phone and charge it, and the refrigeration system will automatically start working. Touch switch for refrigeration: Touch the refrigeration switch icon to cycle alternately (turn on/off refrigeration). Mobilephone is fully charged: Refrigeration automatically stops. Protection function: If the NTC probe detects a temperature above 50 degrees, it indicates that the TEC (Thermoelectric Cooler) is working abnormally and has stopped working. Touch switch: The touch switch (on/off) alternates in a cycle. The blue indicator light remains ON when the refrigeration turns on, and becomes OFF when the refrigeration turns off. When there is no device on the mobile phone, the refrigeration will automatically turn off, and touch the switch to turn on the refrigeration for 5 seconds before refrigeration stops. When there is a charging device on the mobile phone: touch the switch to turn on/off the refrigeration and fan. Touch to turn off the refrigeration and continue the fan for 5 seconds before the fan stops. Wireless charger automatically adjusts its power according to the charging needs of each device. When the mobile device is fully charged, the refrigeration will automatically turn off. ❶ 1. This product can simultaneously charge three types of devices that support wireless charging function, including mobile phones, watches and headset wireless charging boxes. ❷Please connect this wireless charger to the adapter via a Type-C fast charging cable and switch on the power. ❸ 3. Put the mobile phone in the charging area to charge the mobile phone. ❹ Put the watch in the watch charging area to charge the watch. ❺Put the headset wireless charging case in the headset charging area to charge the headset wireless charging case. A PD protocol adapter with a power of more than 30W is required to enable the cooling function.When using a 45W PD adapter, the phone's maximum charging power can reach 25W, and the cooling function can be activated. Name of product Qi2.2 Magnetic 3-in-1 Fast Wireless Charging Station with Active Cooling Product size 100*100*152mm Conversion efficiency 70%-80% Effective distance for wireless charging (mobile phone) ≤3mm Working frequency 110-360KHz Material Do not put metal debris or magnetic cards on the charging board, as it may cause the charger to heat up! Foreign objects should be removed when an alarm is triggered! Slight heating is a normal phenomenon, as the phone battery may generate heat during charging! Do not place the charger near a fire source or corrosive environment ! Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ‐‐ Reorient or relocate the receiving antenna. ‐‐ Increase the separation between the equipment and receiver. ‐‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ‐‐ Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co‐located for operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device must accept any interference received, including interference that may cause undesired operation. Applicable de…

Text truncated - open the document above for the full version.

2.911(d)(5)(i)EquipmentTypeAttestationv1.2 ShenzhenMeskeyTechnologyCo.,Ltd Section2.911(d)(5)(i)Certification–EquipmentType Companyname:ShenzhenMeskeyTechnologyCo.,Ltd Address:Room802,Building1,WestDistrict,HonghuScienceandTechnologyPark, No.22,Ping'anRoad,ZhangxiCommunity,GuanhuStreet,LonghuaDistrict,Shenzhen,China ProductName:TEC3in1WirelessCharger FCCID:2A323-W98-MAX Model(s):W98MAX,W108,W103,W103PRO,W98MAXPRO,W93,W93QI2.2,ProMini MagW5,WP00732 2.911(d)(5)(i)EquipmentType We,[ShenzhenMeskeyTechnologyCo.,Ltd](“theapplicant”)certifythattheequipmentforwhich authorizationissoughtthroughcertificationisnot: Prohibitedfromreceivinganequipmentauthorizationpursuantto§2.903;oftheFCCrules. Identifiedasanequipmenttypeinthe“CoveredList” NOTE1 Yourssincerely, Name:IvanZhangDate:June09,2026 TitleandCompanyname:Manager;ShenzhenMeskeyTechnologyCo.,Ltd NOTE1 “CoveredList ” ;istheListofEquipmentandServicesCoveredBySection2ofTheSecureNetworksAct,availableat https://www.fcc.gov/supplychain/coveredlist References; 1)986446D01CoveredEquipmentv01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2)FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

2.911(d)(5)(ii)ApplicantAttestationv1.2 ShenzhenMeskeyTechnologyCo.,Ltd Section2.911(d)(5)(ii)Certification–Applicant(CoveredList) Companyname:ShenzhenMeskeyTechnologyCo.,Ltd Address:Room802,Building1,WestDistrict,HonghuScienceandTechnologyPark, No.22,Ping'anRoad,ZhangxiCommunity,GuanhuStreet,LonghuaDistrict,Shenzhen,China ProductName:TEC3in1WirelessCharger FCCID:2A323-W98-MAX Model(s):W98MAX,W108,W103,W103PRO,W98MAXPRO,W93,W93QI2.2,ProMini MagW5,WP00732 2.911(d)(5)(ii)Applicantfiling We,[ShenzhenMeskeyTechnologyCo.,Ltd](“theapplicant”)certifythat,asofthedateofthefiling oftheapplication,theapplicantisnotidentified NOTE1 onthe“CoveredList” NOTE2 ,established pursuantto§1.50002ofthischapter,asanentityproducingcoveredcommunicationsequipment. Yourssincerely, Name:IvanZhangDate:June09,2026 TitleandCompanyname:Manager;ShenzhenMeskeyTechnologyCo.,Ltd NOTE1 Deleteoptionnotapplicabletothisapplication. NOTE2 “CoveredList”;istheListofEquipmentandServicesCoveredBySection2ofTheSecureNetworksAct,availableat https://www.fcc.gov/supplychain/coveredlist References; 1)986446D01CoveredEquipmentv01 https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=325672 2)FederalRegisterdocument2022-28263publishedon02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-national-security-threats-to-the-com munications-supply-chain-through-the

ShenzhenMeskeyTechnologyCo.,Ltd AgentAuthorization Company:ShenzhenMeskeyTechnologyCo.,Ltd Address:Room802,Building1,WestDistrict,HonghuScienceandTechnology Park,No.22,Ping'anRoad,ZhangxiCommunity,GuanhuStreet,LonghuaDistrict, Shenzhen,China ProductName:TEC3in1WirelessCharger ModelNumber(s):W98MAX,W108,W103,W103PRO,W98MAXPRO,W93,W93 QI2.2,ProMiniMagW5,WP00732 ProductDescription:TEC3in1WirelessCharger WeauthorizeMiCOMLabsInc.,575BoulderCourt,Pleasanton,California94566,USA, toactonourbehalfonallmattersconcerningthecertificationofabovenamed equipment. WedeclarethatMiCOMLabsInc.isallowedtoforwardallinformationrelatedtothe approvalandcertificationofequipmenttotheregulatoryagenciesasrequiredandto discussanyissuesconcerningtheapprovalapplication.Anyandallactscarriedoutby MiCOMLabsonourbehalfshallhavethesameeffectasactsofourown. Signature:Date:June09,2026 Name:IvanZhang Title:Manager Company:ShenzhenMeskeyTechnologyCo.,Ltd

ShenzhenMeskeyTechnologyCo.,Ltd OfficeofEngineeringTechnology FederalCommunicationsCommission 7435OaklandMillsRoad Columbia,MD21046 Date:June09,2026 Subject;RequestforLongTermConfidentiality FCCID:2A323-W98-MAX ToWhomItMayConcern, PursuanttotheprovisionsoftheCommission’srulesTitle47Sections§0.457and§0.459,weare requestingtheCommissiontowithholdthefollowingattachment(s)asconfidentialdocumentsfrom publicdisclosureindefinitely. Thesedocumentscontaindetailedsystemandequipmentdescriptionsandareconsideredasproprietary informationinoperationoftheequipment.Thepublicdisclosureofthesedocumentsmightbeharmfulto ourcompanyandwouldgivecompetitorsanunfairadvantageinthemarket. SchematicDiagram BlockDiagram PartsList OperationalDescription Tune-upProcedure Itisourunderstandingthatallmeasurementtestreports,FCCIDlabelformatandcorrespondenceduring thecertificationreviewprocesscannotbegrantedasconfidentialdocumentsandthisinformationwillbe availableforpublicreviewoncethegrantofequipmentauthorizationisissued. Sincerely, Signature: Name:IvanZhang Title:Manager

ShenzhenMeskeyTechnologyCo.,Ltd ModelDifferenceDeclaration ToWhomItMayConcern, We,ShenzhenMeskeyTechnologyCo.,Ltd Productname:TEC3in1WirelessCharger Tradename:meskey Modelname:W98MAX,W108,W103,W103PRO,W98MAXPRO,W93,W93 QI2.2,ProMiniMagW5,WP00732 Allmodel ’ sthefunction,softwareandelectriccircuitarethesame,onlywitha productcolorandmodelnameddifferent.Testsamplemodel:W98MAX Pleasecontactmeifyouhaveanyquestion. Name:IvanZhang Date:June09,2026 Title:Manager Signatureofapplicant:

Model: W98 MAX Model: W98 MAX Model: W98 MAX Model: W98 MAX

LabelandLocation FCCID:2A323-W98-MAX

Model: W98 MAX Model: W98 MAX Model: W98 MAX Model: W98 MAX Model: W98 MAX Model: W98 MAX Model: W98 MAX Model: W98 MAX Model: W98 MAX Model: W98 MAX Model: W98 MAX

Page 1 of 17 Report No.: UNIA26052509ER-62 FCC MPE TEST REPORT FCC ID: 2A323-W98-MAX Sample : TEC 3 in 1 Wireless Charger Trade Mark : meskey Main Model : W98 MAX Additional Model : W108, W103,W103 PRO, W98 MAX PRO, W93, W93 QI2.2, ProMini MagW5,WP00732 Report No. : UNIA26052509ER-62 Prepared for Shenzhen Meskey Technology Co., Ltd Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Prepared by Shenzhen United Testing Technology Co., Ltd. D101&D401, No. 107, Kaicheng High-Tech Park, Taoyuan Community, Dalang Sub-District, Longhua District, Shenzhen, Guangdong, China Page 2 of 17 Report No.: UNIA26052509ER-62 TEST RESULT CERTIFICATION Applicant ............................... : Shenzhen Meskey Technology Co., Ltd Address .................................. : Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Manufacturer ........................ : Shenzhen Meskey Technology Co., Ltd Address .................................. : Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Product description Product .................................. : TEC 3 in 1 Wireless Charger Trade Mark ............................. : meskey Model Name ........................... : W108, W103,W103 PRO, W98 MAX PRO, W93, W93 QI2.2, ProMini MagW5,WP00732 Standards ......................... : FCC KDB680106 D01 Wireless Power Transfer v04 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of UNI, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test Date (s) of performance of tests ............ : May 26, 2026 ~ June 03, 2026 Date of Issue ......................................... : June 03, 2026 Test Result ............................................. : Pass Prepared by: Jason Ye/Editor Reviewer: Kelly Cheng/Supervisor Approved & Authorized Signer: Liuze/Manager Page 3 of 17 Report No.: UNIA26052509ER-62 Table of Contents Pages 1 TEST SUMMARY 4 1.1 TEST PROCEDURES AND RESULTS 4 1.2 TEST FACILITY 5 1.3 MEASUREMENT UNCERTAINTY 6 1.4 ENVIRONMENTAL CONDITIONS 6 2 GENERAL INFORMATION 7 2.1 GENERAL DESCRIPTION OF EUT 7 2.2 TEST MODE 8 2.3 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL 9 2.4 TEST INSTRUMENTS 9 3 MAXIMUM PERMISSIBLE EXPOSURE 10 3.1 MAXIMUM PERMISSIBLE EXPOSURE 10 3.2 TEST PROCEDURE 11 3.3 TEST SETUP 11 3.4 RESULT OF MAXIMUM PERMISSIBLE EXPOSURE 12 3.5 TEST PHOTO 15 Page 4 of 17 Report No.: UNIA26052509ER-62 1 TEST SUMMARY 1.1 TEST PROCEDURES AND RESULTS FCC KDB680106 D01 Wireless Power Transfer v04 FCC CFR 47 Standard Section Test Item Result Remark FCC CFR 47 part1, 1.1310 KDB680106 D01 v04 Electric Field Strength (E) (V/m) N/A -- Magnetic Field Strength (H) (A/m) PASS -- Note: “N/A” denotes test is not applicable in this Test Report. Compliant with FCC KDB680106 D01 Wireless Power Transfer v04 section 5.2: 1) The power transfer frequency is below 1MHz. Yes, the working frequency is: 110-360kHz . 2) The output power from each transmitting element (e.g., coil) is less than or equal to 15 watts. No, the maximum output power is 25 watts. 3) A client device providing the maximum permitted load is placed in physical contact with the transmitter(i.e. , the surfaces of the transmitter and client device enclosures need to be in physical contact) Yes, the maximum permitted load is placed in physical contact with the transmitter. 4) Only $ 2.1091-Mobile exposure conditions apply (i.e., this provision does not cover $ 2.1093-Portable exposure conditions). Yes, this provision does not cover $ 2.1093-Portable exposure conditions. 5) The H-field strengths, at and beyond 20 cm surrounding the device surface, are demonstrated to be less than 50% of the applicable MPE limit, per KDB 447498, Table 1. These measurements shall be taken along the principal axes of the device, with one axis oriented along the direction of the estimated maximum field strength, and for three points per axis or until a 1/d (inverse distance from the emitter structure) field strength decay is observed. Symmetry considerations may be used for test reduction purposes. The device shall be operated in documented worst-case compliance scenarios(i.e. , the ones that lead to the maximum field components), and while all the radiating structures (e.g., coils or antennas) that by design can simultaneously transmit are energized at their nominal maximum power. Yes, The H-field strengths, at and beyond 20 cm surrounding the device surface, are demonstrated to be less than 50% of the applicable MPE limit ; coils or antennas) that by design can simultaneously transmit are energized at their nominal maximum power. Page 5 of 17 Report No.: UNIA26052509ER-62 6) For systems with more than one radiating structure, the conditions specified in (5) must be met when the system is fully loaded (i.e., clients absorbing maximum power available), and with all the radiating structures operating at maximum power at the same time, as per design conditions. If the design allows one or more radiating structures to be powered at a higher level while other radiating structures are not powered, then those cases must be tested as well. For instance, a device may use three RF coils powered at 5 W, or one coil powered at 15 W: in this case, both scenarios shall be tested. Yes, For systems with more than one radiating structure, the conditions speci…

Text truncated - open the document above for the full version.

深圳市宸兴电子技术有限公司 公司名称：深圳市宸兴电子技术有限公司 工厂地址：深圳市宝安区新安街道大宝路51号新柯城科技工业园1栋5楼 第 1 页 产品规格书 PRODUCTSPECIFICATIONFORAPPROVAL 客户名称： CUSTOMER 产品名称： PRODUCTNAME A11 线圈 物料编码： PARTNo. 产品规格： PRODUCTSPEC 感量：6.3uH±10% 磁片规格：43.5*5.3*1双槽 线材规格：0.08*105*10Ts/出线18mm 贴背胶 日期： DATE 2022年10月07日 版本型号： VERSION REV1.0 版本 Revision 变更内容 ModifiedContent 责任人 Principle 日期 Date 备注 Note REV1.0首次发布薛磊2022-10-07 制定/PREPAREDBY审核/CHECKEDBY核准/APPROVEDBY 客户认可签名及盖章 Authorizedsignature& companychop 附上的是产品规格书，有任何疑问，请及时反馈给我们，谢谢 ! 深圳市宸兴电子技术有限公司 公司名称：深圳市宸兴电子技术有限公司 工厂地址：深圳市宝安区新安街道大宝路51号新柯城科技工业园1栋5楼 第 2 页 产品规格 SPECIFICATION 一、产品尺寸 磁片直径 A 43.5±0.5mm 线圈外径B42±1mm 线圈内径C20.5±0.5mm 产品厚度D<2.5mm 出线长度E18mm±3mm 焊锡长度F2-5mm 磁片开孔直径G5±0.3mm 磁片厚度1±0.1mm 磁片形状圆形双槽 背胶厚度普通双面胶 防碎黑膜不 深圳市宸兴电子技术有限公司 公司名称：深圳市宸兴电子技术有限公司 工厂地址：深圳市宝安区新安街道大宝路51号新柯城科技工业园1栋5楼 第 3 页 二、原理图 三、绕线参数 端子 TERMINAL 线径 WIRE 圈数 Turns 绕线方向 WindingDirection SF 丝包线 0.08*105P 10TsCCW 四、电气特性： 温度TEMPERATURE:25±10°C,湿度RELATIVEHUMIDITY:65±20% 项目 ITEM 端子 TERMINAL 标准 SPECIFICATION 测试条件 TESTFREQUENCY 测试仪器 TESTEQUIPMENTS IND.S-F 6.3uH±10% 100KHz/1.0VLCZMETER1062B 五、产品图片 深圳市宸兴电子技术有限公司 公司名称：深圳市宸兴电子技术有限公司 工厂地址：深圳市宝安区新安街道大宝路51号新柯城科技工业园1栋5楼 第 4 页 六、包装说明： 珍珠棉尺寸为35*24.5*6.2cm,每 个珍珠棉共有40个格子，每个格 子装6PCS产品，共240PCS产品 每箱装三层珍珠棉； 纸箱尺寸为：36.5*25.5*21CM， 每箱装720PCS产品。

产品承认书书 规格编号 HG2025041001 生效日期 客户名称 二维四象智能科技有限责任公司 产品类型QI2线圈 宏贵料号 43.5*0.8 开双槽带孔背白胶 /0.08*80 丝包线 客户料号 【 □ √√ 新版发行 ,□ 版本修订】【本规范含目录共 2 页】【 RoHSCompliantParts 】 编制审核批准 彭建基 安福宏贵电子有限公司 本承认书在客户收到一星期内，请务必签章返回，逾期视为生产时按此承认书的标准 执行。 【客户核准】日期: 承认状态：□完全承认□条件承认□拒绝承认 批准审核 复检检查 说明: 产品规格书 客户名称二维四象智能科技有限责任公司客户料号 宏贵料号 43.5*0.8开双槽带孔0.08*80股丝包线 规格编号 HG2025041001 版本 01 ♦、外形尺寸 ♦、电气特性: (单位:mm) A 43.5±0.5 B 40.0±1 C20.5±0.5 D2.1±0.2 E200±2 F2.0±1 G (1)线径:0.08*80P丝包自粘铜线 (2)绕线圈数:11TS (3)起尾线是否交叉:是 (4)线圈包6mm宽高温胶带 (5)线圈与磁片需粘贴居中 (6)线圈中间贴直径20MM厚度1.0MM圆片 (7)磁片背圆双面胶 参数规格测试条件测试仪器 L07.9±0.3μH 100KHz/1V ■TH1816B ■TH1816B ■CH-502BC Q>30min 100KHz/1V DCR<60mΩ @25°C 操作温度 -40°C~125°C ♦、材料清单: 序号 1 品名材料规格供应商备注 2 磁片20*1.0圆片PC95猛锌 3 磁片43.5*0.8开双槽带孔PC95猛锌 4 铜线0.08*80P丝包自粘铜线 5 高温胶带 6MM 环保胶带 6 锡高温锡条千岛环保锡 7 胶白胶环保胶水 8 白胶 42 圆双面胶 编制审核 批准 彭建基

GivebirthtoArticleLetterofrecognition Book SpecificatHG20250829001 Effective Customer'sname Two-dimensionalfour-imageintelligenttechnologylimited liabilitycompany Producttype QI2Coil Hongguimaterial number 42.5*0.8 Opendoublegroovewithhole /0.08*80 Multi-stranded wire Customer materialnumber [√□Thenewversionisreleased,□Versionrevision][Thisspecificationcontains atotalof Two Page][ RoHSCompliantParts ] WeaveCheckRatify PengJianji AnfuHongguiElectronicsCo.,Ltd. Building2,NewEnergylndustrialpark,SouthAreaofAnfuHigh-techlndustrialpark,Ji’anCity,JiangxiProvince Pleasebesuretosignandreturnthisacknowledgementwithinoneweekafter thecustomerreceivesit.Overdueshallbedeemedtobeimplementedaccordingto thestandardofthisletterofrecognitionatthetimeofproduction. [Customerapproval] Date: Recognitionstatus: □ Fullyadmit □ Conditionalrecognition □ Refusetoadmit RatifyCheckRe-inspectionExamine Explain: Customer's name Two-dimensionalfour-image intelligenttechnologylimited liabilitycompany Custome r materia l number Honggui material number ♦ , Externa l 42.5*0.8Opendoublegroove hole/0.08*80Multi-stranded with wire Specifi catiHG20250829001 on number Edition (Unit:mm) A 42.5±0.5 B40.0±1 C20.5±0.5 D2.1±0.2 E15±2 F2±1 (1)Wirediameter:0.08*80Psilk- wrappedself-adhesivecopper wire (2)Thenumberofwindingcoils:11 TS (3)Whetherthestartingandending linesintersect:Yes (4)CoilpackageSixmillimetersWide high-temperaturetape (5)Thecoilandthemagneticsheet shouldbepastedinthestering. Six(6)Diameterofthemiddleofthe coil20MMThickness1.0 millimetreRoundpiece Parameter L0 Specifications 7.9±0.3μH Test conditions 100K Hz/1V Testinstrument ■TH181 Q >30minutes 100K Hz/1V ■TH181 DCR. <60MΩ Billof materials: Serials 1 Materials 2 Magneticsheet20*1.0Roundpiece PC95Strongzinc 3 Magneticsheet 42.5*0.8Doubleslotswith holes PC95Strongzinc 4 Copperwire0.08*80P Silk-wrappedself-adhesivecopperwire 5 High-temperaturet ape 6MM Eco-friendiyadhesivetape 6 TinHightemperatuertinbar Thousandislandenvironmentaltin 7 GlueWhiteglues Eco-friendlyadhesive AUTHORCHECK APPROVE pengjianji @twenty five°C ■CH-502 01

Page 1 of 29 Report No.: UNIA26052509ER-61 FCC RADIO TEST REPORT FCC ID: 2A323-W98-MAX Sample : TEC 3 in 1 Wireless Charger Trade Mark : meskey Main Model : W98 MAX Additional Model : W108, W103,W103 PRO, W98 MAX PRO, W93, W93 QI2.2, ProMini MagW5,WP00732 Report No. : UNIA26052509ER-61 Prepared for Shenzhen Meskey Technology Co., Ltd Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Prepared by Shenzhen United Testing Technology Co., Ltd. D101&D401, No. 107, Kaicheng High-Tech Park, Taoyuan Community, Dalang Sub-District, Longhua District, Shenzhen, Guangdong, China Page 2 of 29 Report No.: UNIA26052509ER-61 TEST RESULT CERTIFICATION Applicant .............................. : Shenzhen Meskey Technology Co., Ltd Address ................................. : Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Manufacturer........................ : Shenzhen Meskey Technology Co., Ltd Address ................................. : Room 802, Building 1, West District, Honghu Science and Technology Park, No. 22, Ping 'an Road, Zhangxi Community, Guanhu Street, Longhua District, Shenzhen,China Product description Product .................................. : TEC 3 in 1 Wireless Charger Trade Mark ............................ : meskey Model Name .......................... : W98 MAX,W108, W103,W103 PRO, W98 MAX PRO, W93, W93 QI2.2, ProMini MagW5,WP00732 Test Methods ....................... : FCC Rules and Regulations Part 15 Subpart C Section 15.209 ANSI C63.10: 2020 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test Date (s) of performance of tests ............. : May 26, 2026 ~ June 03, 2026 Date of Issue .......................................... : June 03, 2026 Test Result ............................................. : Pass Prepared by: Jason Ye/Editor Reviewer: Kelly Cheng/Supervisor Approved & Authorized Signer: Liuze/Manager Page 3 of 29 Report No.: UNIA26052509ER-61 Table of Contents Pages 1 TEST SUMMARY 4 1.1 TEST PROCEDURES AND RESULTS 4 1.2 TEST FACILITY 4 1.3 MEASUREMENT UNCERTAINTY 5 2 GENERAL INFORMATION 6 2.1 GENERAL DESCRIPTION OF EUT 6 2.2 TEST MODE 7 2.3 TEST SETUP 7 2.4 DESCRIPTION TEST PERIPHERAL AND EUT PERIPHERAL 8 2.5 MEASUREMENT INSTRUMENTS LIST 9 3 CONDUCTED EMISSION 11 3.1 TEST LIMIT 11 3.2 TEST SETUP 11 3.3 TEST PROCEDURE 12 3.4 TEST RESULT 12 4 RADIATED EMISSION 15 4.1 TEST LIMIT 15 4.2 TEST SETUP 17 4.3 TEST PROCEDURE 18 4.4 TEST RESULT 18 5 ANTENNA REQUIREMENT 24 6 PHOTO OF TEST 26 6.1 RADIATED EMISSION 26 6.2 CONDUCTED EMISSION 27 7 EUT Constructional Details 28 Page 4 of 29 Report No.: UNIA26052509ER-61 1 TEST SUMMARY 1.1 TEST PROCEDURES AND RESULTS Item FCC Rules Description Of Test Result 1 FCC Part 15.207 Conducted Emission Pass 2 FCC Part 15.209(a) Radiated Emission Pass 3 FCC Part 15.203 Antenna Requirement Pass 1.2 TEST FACILITY Test Firm : Shenzhen United Testing Technology Co., Ltd. Address : D101&D401, No. 107, Kaicheng High-Tech Park, Taoyuan Community, Dalang Sub-District, Longhua District, Shenzhen, Guangdong, China The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19.The testing quality system of our laboratory meets with ISO/IEC-17025 requirements. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: A2LA Certificate Number: 4747.01 The EMC Laboratory has been accredited by A2LA, and in compliance with ISO/IEC 17025:2017 General Requirements for testing Laboratories. FCC Registration Number: 674885 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. IC Registration Number: 31584 The EMC Laboratory has been registered and fully described in a report filed with the (IC) Industry Canada. Page 5 of 29 Report No.: UNIA26052509ER-61 1.3 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %. A. Conducted Measurement: Test Site Method Measurement Frequency Range U, (dB) NOTE UNI ANSI 9KHz ~ 150KHz 2.96 150KHz ~ 30MHz 2.44 B. Radiated Measurement: Test Site Method Measurement Frequency Range U, (dB) NOTE UNI ANSI 9KHz ~ 30MHz 2.50 30MHz ~ 1000MHz 4.80 1000MHz ~ 6000MHz 4.13 Page 6 of 29 Report No.: UNIA26052509ER-61 2 GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Product: TEC 3 in 1 Wireless Charger Trade Mark: meskey Main Model: W98 MAX Additional Model: W108, W103,W103 PRO, W98 MAX PRO, W93, W93 QI2.2, ProMini MagW5,WP00732 Model Difference: All model’s the function, software and electric circuit are the same, only with a product color and model named different. Test sample model: W98 MAX FCC ID: 2A323-W98-MAX Operation Frequency: Phone: 110-360kHz TWS: 110-205kHz Watch: 326.5kHz Modulation Type: ASK Wireless Charging Output Power: Output1:Phone 25W(max) Output2:TWS 5W(max) Output3:Watch 2.5W Antenna Type: Coil Antenna Antenna Gain: 0dBi Battery: N/A Adapter: N/A Power Source: DC 15V/20V by Adapter Page 7 of 29 Report No.: UNIA26052509ER-61 2.2 TEST MODE NO. TEST MODE DESCRIPTION 1 ANT 1(Phone coil) + Full load (25W Folding mode) 2 ANT 1(Phone coil) + Half load (7.5W Folding mode) 3 ANT 1…

Text truncated - open the document above for the full version.

Model:W98MAX RadiatedEmissiontest Model:W98MAX ConductedEmissiontest Model:W98MAX MPE Model:W98MAX Model:W98MAX