2A3OORB48PTwo Way Radio

RB48 Plus Two Way Radio USER'S MANUAL CONTENT Warning ----------------------------------- Charging Attentions ----------------------- Main Features---------------------------- Familiar with Radio ------------------------ Display ------------------------------------ Key Instructions---------------------------- Function Operations ----------------------- Factory Frequency ------------------------- CTCSS/DCS Codes ------------------------- Specifications ------------------------------ Fault Emission ----------------------------- Guarantee --------------------------------- 01 01 01 02 02 03 03 06 07 07 08 12 For downloading further resources: Brochures, Software/Firmware, Manual etc, Please contact your direct reseller first OR go to website retevis.com and check “support” in the each product link to download it. Warning: Please read the manual carefully before using the radio. ●Don’t charge the radio in flammable, explosive, and radio communication prohibited areas (gas station, airport, etc). ●Don’t operate the radio without a license in government-prohibited areas. ●Avoid exposing the radio to the sun, and avoid putting the radio near any heating equipment. ●Avoid putting the radio in dust, wet, or splashing water places, and avoid putting the radio near any heating equipment. ●Remove the battery pack from the radio immediately and contact the nearest retailers if the radio smells or smokes. ●The radio is repaired by the technical, self-disassembly is strictly prohibited. Charging Attentions： ●Please use the matched charger to charge the radio. ●Turn off the radio before charging the radio. ●To get the best battery performance, please charge at least 5 hours the first time. ●Don’t charge the battery pack for a long time, otherwise, the service life of the battery will shorten. When fully charged, please stop charging in time. ●The charger only charges the radio. Don’t charge other battery packs, otherwise, the charger and the battery will be damaged. ●When fully charged, put the battery pack in cool and dry areas. Don’t be near the fire or exposure to the sun. Otherwise, it will exist a safety hazard. ●Don’t turn on the radio during charging. ●During charging, it is common that the battery pack is slightly heated. ●Obey the local regulations when using the radio. Main Features ●IP67 Waterproof ●LCD Backlight Display ●30 Channels ●159 CTCSS/DCS Codes (50 CTCSS, 109 DCS) ●Channel Busy Lock ●Earpiece Jack ●10 Call Tones ●VOX ●High/Low Power Selection ●Call End Tone ●One-key Cancel CTCSS/DCS ●Scan/Priority Channel Scan ●Keypad Lock ●Channel Hidden ●English Voice Broadcast ●Battery Save ●Low Battery Alert ●Local and Remote Alarm ●TOT ●Call Vibration ●Talk Around ●Easy Pairing（Pair one channel and Pair all channels） ●One-key Group Call ●PTT ID（only transmit） ●Double PTT ●Allow Transmission Prompt ●NOAA ●Monitor ●Roger Beep ●Squelch ●Restore Factory Mode ●Mic Gain 01 Familiar with Radio A. Antenna B. Earpiece jack C. Power/Volume knob D. LCD display E. PTT F. NOAA/Call tone key G. Menu/Key lock key H. Monitor/Scan key I. Speaker J .Type-C charging port K. Mic port L.【▲】&【▼】Button A B C D E E F G H I J L L K Display No 1 2 3 4 5 6 7 8 9 10 11 Instruction Group call Scan High power VOX Battery indicate Transmit Receive NOAA/NOAA alert Keypad lock CTCSS/DCS codes, 00 stands for non CTCSS/DCS Channel number Icon 02 Key Instructions ●【PTT】Key Use double PTT to transmit. One is the small PTT key on the side, and the other is the big PTT key in the front. In menu mode, press the PTT key to save settings and exit the menu. ●【▲】Key Shortly press: Switch options up in the menu Long press: Customized side key, OFF, Werther, Alarm, Call, Monitor, and Group call. Factory default: Monitor ●【▼】Key Shortly press: Switch options down in the menu Long press: Customized side key, OFF, Werther, Alarm, Call, Monitor, and Group call. Factory default: Alarm ●【 /CALL】Key Shortly press: Send Call Tone Long press: Two-way radio and Weather switch ●【MENU】 Shortly press: Enter or switch the menu Long press: Lock or unlock ●【Mon/Scan】 Shortly press: Turn on or off the scan Long press: Turn on the monitor Function Operations 1.Turn on/off the Radio Clockwise rotate the power knob to turn on the radio. Anticlockwise rotate the power knob and hear a click sound to turn off the radio. When turning on the radio, it will have a power-on prompt and display all icons. After turning on the radio, it will stay in two-way radio mode and display the current channel number, CTCSS/DCS codes, etc. 2.Volume Adjustment Clockwise rotate the knob to increase the volume. Anticlockwise rotate the knob to decrease the volume. Note: don’t put the radio speaker too close to the ear when the volume does not adjust to a proper state. Otherwise, a loud voice will hurt the ears. 3.Transmit & Receive 1.Press the PTT key and away the microphone from 3-5cm. Speak in a normal voice. When the radio displays the transmit icon , the radio is transmitting. To avoid stopping your talk, press the PTT key and pause, then start to talk . When finishing talk, release the PTT key to receive. When receiving, the radio displays the receive icon . 4.Key Lock Key lock function aims to prevent changing radio settings from accidental operations. 1.Long press the Menu key, hear a beep sound, and the radio displays icon, the radio enters key lock status. 2.Long press the menu key, hear two beep sounds, and the radio displays icon, the radio exits key lock status. Note: In key lock status, press any key except the PTT key, the radio will send failure sound. 5.Menu Setting ●Channel Selection 1.In standby status, press the Menu key once. The current channel number flashes. 2.Press the ▲ or ▼ key to select the wanted channel number. 3.Press the PTT key to save the current setting and exit the menu, or press the Menu key to the next menu setting. 4.The radios can communicate when they are set as the same channel. ●CTCSS/DCS Codes Selection CTCSS/DCS codes can reduce the interfe…

Text truncated - open the document above for the full version.

Shenzhen Ysair Technology Co., LTD Room 403, 4th Floor, Building 4, Yunli intelligent Park, No. 3 Changfa Middle Road, Yangmei Community, Bantian Street, Longgang District, Shenzhen,China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Aug. 12, 2024 Ref: Attestation Statements Part 2.911(d)(5)(i) Filing FCC ID: 2A3OORB48P FRN: 0031641426 Shenzhen Ysair Technology Co., LTD (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, ________________________ Applicant signature Dongfang Shen, Manager

Shenzhen Ysair Technology Co., LTD Room 403, 4th Floor, Building 4, Yunli intelligent Park, No. 3 Changfa Middle Road, Yangmei Community, Bantian Street, Longgang District, Shenzhen,China Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Aug. 12, 2024 Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing FCC ID: 2A3OORB48P FRN: 0031641426 Shenzhen Ysair Technology Co., LTD (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, ________________________ Applicant signature Dongfang Shen, Manager

CFR 47 §2.911(d)(7) U.S Agent U.S. AGENT LETTER OF ATTESTATION Date: 2024-08-12 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2A3OORB48P Shenzhen Ysair Technology Co., LTD ( “the Applicant”) certifies that, as of the date of the filing of the application, RETEVIS INC. (U.S. agent). is our designated U.S. agent for service of process for the above referenced FCC ID. Shenzhen Ysair Technology Co., LTD (“the Applicant”)accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission- related proceeding involving the equipment. RETEVIS INC. (U.S. agent) accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Company Name: RETEVIS INC. Address: 1733 E BROOKPORT ST, COVINA, CA 91724 FRN: 0033657701 Tel.: +1（626）3622594 Email: [email protected] Signed by (printed name): LIUYE LI Signature: Applicant: Shenzhen Ysair Technology Co., LTD Add: Rom 403, 4th Floor, building 4, Yunli intelligent park, No. 3, Changfa, Middle Road, Yangmei community, Bantian street, Longgang District, Shenzhen, Guangdong,China FRN: 0031641426 Tel: +86-755-23481953 Email: [email protected] Signed by (printed name): Dongfang Shen Signature:

Shenzhen Ysair Technology Co., LTD Room 403, 4th Floor, Building 4, Yunli intelligent Park, No. 3 Changfa Middle Road, Yangmei Community, Bantian Street, Longgang District, Shenzhen,China Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Aug. 12, 2024 Subject; Request for Confidentiality FCC ID: 2A3OORB48P To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Operational Description Parts List Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); External Photos Test Setup Photos Internal Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. OR For 180 days pursuant to KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, ________________________ Signature: Dongfang Shen, Manager

Letter of Authorization Company: Shenzhen Ysair Technology Co., LTD Address: Room 403, 4th Floor, Building 4, Yunli intelligent Park, No. 3 Changfa Middle Road, Yangmei Community, Bantian Street, Longgang District, Shenzhen,China Product Name: Two Way Radio Model Number(s): RB48 Plus Product Description: Two Way Radio We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Aug. 12, 2024 Name: Dongfang Shen Title: Manager Company: Shenzhen Ysair Technology Co., LTD

Report No.: AGC13372240603AP02 Page 1 of 4 EXTERNAL PHOTOS All VIEW OF EUT TOP VIEW OF EUT GMRS Antenna Report No.: AGC13372240603AP02 Page 2 of 4 BOTTOM VIEW OF EUT FRONT VIEW OF EUT Report No.: AGC13372240603AP02 Page 3 of 4 BACK VIEW OF EUT LEFT VIEW OF EUT Report No.: AGC13372240603AP02 Page 4 of 4 RIGHT VIEW OF EUT CHARGER OF EUT ****************************************End of Report*************************************

FCC ID Label Location 30mm*15mm FCC ID: 2A3OORB48P

Report No.: AGC13372240602AP02 Page 1 of 9 INTERNAL PHOTOS PORT VIEW OF EUT-1 PORT VIEW OF EUT-2 Report No.: AGC13372240602AP02 Page 2 of 9 OPEN VIEW OF EUT (FIGURE 1) OPEN VIEW OF EUT (FIGURE 2) Report No.: AGC13372240602AP02 Page 3 of 9 OPEN VIEW OF EUT (FIGURE 3) Report No.: AGC13372240602AP02 Page 4 of 9 INTERNAL VIEW OF EUT (FIGURE 1) INTERNAL VIEW OF EUT (FIGURE 2) Report No.: AGC13372240602AP02 Page 5 of 9 INTERNAL VIEW OF EUT (FIGURE 3) INTERNAL VIEW OF EUT (FIGURE 4) Report No.: AGC13372240602AP02 Page 6 of 9 INTERNAL VIEW OF EUT (FIGURE 5) INTERNAL VIEW OF EUT (FIGURE 6) Report No.: AGC13372240602AP02 Page 7 of 9 INTERNAL VIEW OF EUT (FIGURE 7) INTERNAL VIEW OF EUT (FIGURE 8) Report No.: AGC13372240602AP02 Page 8 of 9 INTERNAL VIEW OF EUT (FIGURE 9) BATTERY OF EUT Report No.: AGC13372240602AP02 Page 9 of 9 ****************************************End of Report*************************************

Page 1 of 18 CALIBRATION DATA PROBE CALIBRATION DATA Page 2 of 18 Page 3 of 18 Page 4 of 18 Page 5 of 18 Page 6 of 18 Page 7 of 18 Page 8 of 18 Page 9 of 18 Page 10 of 18 DAE CALIBRATION DATA Page 11 of 18 Page 12 of 18 Page 13 of 18 DIPOLE CALIBRATION DATA Page 14 of 18 Page 15 of 18 Page 16 of 18 Page 17 of 18 Page 18 of 18

Page 1 of 49 SAR Test Report Report No.: AGC13372240603FH01 FCC ID : 2A3OORB48P PRODUCT DESIGNATION : Two Way Radio BRAND NAME : RETEVIS MODEL NAME : RB48 Plus APPLICANT : Shenzhen Ysair Technology Co., LTD DATE OF ISSUE : Jul. 30, 2024 STANDARD(S) : IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2005 REPORT VERSION : V1.0 Attestation of Global Compliance(Shenzhen) Co., Ltd. Report No.: AGC13372240603FH01 Page 2 of 49 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jul. 30, 2024 Valid Initial Release Report No.: AGC13372240603FH01 Page 3 of 49 Test Report Applicant Name Shenzhen Ysair Technology Co., LTD Applicant Address Room 403, 4th Floor, Building 4, Yunli intelligent Park, No. 3 Changfa Middle Road, Yangmei Community, Bantian Street, Longgang District, Shenzhen, China Manufacturer Name Shenzhen Ysair Technology Co., LTD Manufacturer Address Room 403, 4th Floor, Building 4, Yunli intelligent Park, No. 3 Changfa Middle Road, Yangmei Community, Bantian Street, Longgang District, Shenzhen, China Factory Name N/A Factory Address N/A Product Designation Two Way Radio Brand Name RETEVIS Model Name RB48 Plus EUT Voltage DC 7.4 V Applicable Standard IEEE Std. 1528:2013 FCC 47 CFR Part 2§2.1093 IEEE Std C95.1 ™-2005 Date of receipt of test item Jun. 24, 2024 Test Date Jul. 02, 2024 Report Template AGCRT- US -PTT/SAR (2021-04-20) Note: The results of testing in this report apply to the product/system which was tested only. Prepared By Bibo Zhang (Project Engineer) Jul. 30, 2024 Reviewed By Calvin Liu (Reviewer) Jul. 30, 2024 Approved By Max Zhang (Authorized Officer) Jul. 30, 2024 Report No.: AGC13372240603FH01 Page 4 of 49 TABLE OF CONTENTS 1. SUMMARY OF MAXIMUM SAR VALUE ......................................................................................................... 5 2. GENERAL INFORMATION ............................................................................................................................... 6 2.1. EUT DESCRIPTION......................................................................................................................................... 6 3. SAR MEASUREMENT SYSTEM ........................................................................................................................ 7 3.1. THE DASY5 SYSTEM USED FOR PERFORMING COMPLIANCE TESTS CONSISTS OF FOLLOWING ITEMS .................... 7 3.2. DASY5 E-FIELD PROBE ................................................................................................................................. 8 3.3. DATA ACQUISITION ELECTRONICS DESCRIPTION ............................................................................................... 8 3.4. ROBOT .......................................................................................................................................................... 9 3.5. LIGHT BEAM UNIT .......................................................................................................................................... 9 3.6. DEVICE HOLDER .......................................................................................................................................... 10 3.7. MEASUREMENT SERVER ............................................................................................................................... 10 3.8. PHANTOM ................................................................................................................................................. 11 4. SAR MEASUREMENT PROCEDURE ............................................................................................................ 12 4.1. SPECIFIC ABSORPTION RATE (SAR) .............................................................................................................. 12 4.2. SAR MEASUREMENT PROCEDURE ................................................................................................................ 13 5. TISSUE SIMULATING LIQUID ....................................................................................................................... 15 5.1. THE COMPOSITION OF THE TISSUE SIMULATING LIQUID..................................................................................... 15 5.2. TISSUE DIELECTRIC PARAMETERS FOR HEAD AND BODY PHANTOMS ............................................................... 15 5.3. TISSUE CALIBRATION RESULT ....................................................................................................................... 16 6. SAR SYSTEM CHECK PROCEDURE ........................................................................................................... 17 6.1. SAR SYSTEM CHECK PROCEDURES ............................................................................................................. 17 7. EUT TEST POSITION ...................................................................................................................................... 19 7.1. BODY WORN POSITION ................................................................................................................................ 19 8. SAR EXPOSURE LIMITS ............................................................................................................................... 20 9. TEST FACILITY .............................................................................................................................................. 21 10. TEST EQUIPMENT LIST .............................................................................................................................. 22 11. MEASUREMENT UNCERTAINTY ................................................................................................................ 23 12. POWER MEASUREMENT ............................................................................................................................ 27 13. TEST RESULTS .................................................................…

Text truncated - open the document above for the full version.

Page 1 of 55 FCC Test Report Report No.: AGC13372240603FR01 FCC ID : 2A3OORB48P APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Two Way Radio BRAND NAME : RETEVIS MODEL NAME : RB48 Plus APPLICANT : Shenzhen Ysair Technology Co., LTD DATE OF ISSUE : Jul. 26, 2024 STANDARD(S) : FCC Part 95 Subpart E REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC13372240603FR01 Page 2 of 55 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jul. 26, 2024 Valid Initial Release Report No.: AGC13372240603FR01 Page 3 of 55 Table of Contents 1. General Information ........................................................................................................................................ 5 2. Product Information ........................................................................................................................................ 6 2.1 Product Technical Description ................................................................................................................... 6 2.2 Test Frequency List ................................................................................................................................... 7 2.3 Related Submittal(S) / Grant (S) ............................................................................................................... 8 2.4 Test Methodology ...................................................................................................................................... 8 2.5 Calculation of Emission Indicators ............................................................................................................ 8 2.6 Special Accessories .................................................................................................................................. 8 2.7 Equipment Modifications ........................................................................................................................... 8 2.8 Antenna Requirement ............................................................................................................................... 9 3. Test Environment .......................................................................................................................................... 10 3.1 Address of The Test Laboratory .............................................................................................................. 10 3.2 Test Facility .............................................................................................................................................. 10 3.3 Environmental Conditions ....................................................................................................................... 11 3.4 Measurement Uncertainty ....................................................................................................................... 11 3.5 List of Equipment Used ........................................................................................................................... 12 4. System Test Configuration ........................................................................................................................... 14 4.1 EUT Configuration ................................................................................................................................... 14 4.2 EUT Exercise ........................................................................................................................................... 14 4.3 Configuration of Tested System .............................................................................................................. 14 4.4 Equipment Used in Tested System ......................................................................................................... 14 4.5 Summary of Test Results ........................................................................................................................ 15 5. Description of Test Modes ........................................................................................................................... 16 6. Frequency Stability ....................................................................................................................................... 17 6.1 Provisions Applicable .............................................................................................................................. 17 6.2 Measurement Procedure ......................................................................................................................... 17 6.3 Measurement Setup ................................................................................................................................ 17 6.4 Measurement Result ............................................................................................................................... 18 7. 26dB Emission Bandwidth and 99% Occupied Bandwidth ...................................................................... 20 7.1 Provisions Applicable .............................................................................................................................. 20 7.2 Measurement Procedure ......................................................................................................................... 20 7.3 Measurement Setup ................................................................................................................................ 20 7.4 Measurement Result ............................................................................................................................... 21 8. Spurious Radiated Emission ......................................................................................................................... 24 7.1 Provisions Applicable ....................................................................................................................…

Text truncated - open the document above for the full version.

Report No.: AGC13372240603FR01 Page 51 of 55 12.5kHz, FM modulation, Assigned Frequency:467.6375MHz, 0.5W Report No.: AGC13372240603FR01 Page 52 of 55 12. Audio Low Pass Filter Response 12.1 Provisions Applicable §95.1775 GMRS modulation requirements Audio filter. Each GMRS transmitter type must include audio frequency low pass filtering, unless it complies with the applicable paragraphs of §95.1779 (without filtering). The filter must be between the modulation limiter and the modulated stage of the transmitter. At any frequency (f in kHz) between 3 and 20 kHz, the filter must have an attenuation of at least 60 log (f/3) dB more than the attenuation at 1 kHz. Above 20 kHz, it must have an attenuation of at least 50 dB more than the attenuation at 1 kHz 12.2 Measurement Procedure 1. The DUT transmitter output port was connected to Modulation Analyzer. 2. Path loss for the measurement included. 3. Press 23.1SPCL on modulation analyzer to enable the external LO from SIgen. 4. Set the Sigen frequency to Fc + 1.5MHz, RF output level to 0dBm without modulation. 5. Transmit the radio and set the audio analyzer to 1 kHz audio frequency and 60% of the maximum deviation. 6. Up the amplitude by 20dB. 7. On DSA, get the reference point to 0dB. 8. Vary the frequency on audio analyzer from 3 kHz to 30 kHz, record the audio tone from DSA. 12.3 Measurement Setup Report No.: AGC13372240603FR01 Page 53 of 55 12.4 Measurement Result 12.5kHz, FM modulation, Assigned Frequency:462.6500MHz-5W Audio Frequency (kHz) Response Attenuation (dB) Limit (dB) 1 0 / 3 -2.48 0.00 4 -8.96 -5.00 5 -13.39 -8.87 6 -17.37 -12.04 7 -20.41 -14.72 8 -23.40 -17.04 9 -26.20 -19.08 10 -29.36 -20.92 15 -36.69 -28.00 20 -34.39 -28.00 30 -33.27 -28.00 50 -32.15 -28.00 70 -31.96 -28.00 Note: All test frequencies was tested, but only the worst data be recorded in this part. Report No.: AGC13372240603FR01 Page 54 of 55 25kHz, FM modulation, Assigned Frequency:462.6500MHz-5W Audio Frequency (kHz) Response Attenuation (dB) Limit (dB) 1 0 / 3 -3.13 0.00 4 -10.61 -5.00 5 -17.12 -8.87 6 -21.37 -12.04 7 -25.26 -14.72 8 -27.82 -17.04 9 -30.33 -19.08 10 -32.28 -20.92 15 -36.69 -28.00 20 -36.52 -28.00 30 -33.97 -28.00 50 -32.22 -28.00 70 -30.04 -28.00 Note: All test frequencies was tested, but only the worst data be recorded in this part. Report No.: AGC13372240603FR01 Page 55 of 55 Appendix I: Photographs of Test Setup Refer to the Report No.: AGC13372240603AP01 Appendix II: Photographs of Test EUT Refer to the Report No.: AGC13372240603AP02 -----End of Report----- Conditions of Issuance of Test Reports 1. All samples and goods are accepted by the Attestation of Global Compliance (Shenzhen) Co., Ltd (the “Company”) solely for testing and reporting in accordance with the following terms and conditions. The company provides its services on the basis that such terms and conditions constitute express agreement between the company and any person, firm or company requesting its services (the “Clients”). 2. Any report issued by Company as a result of this application for testing services (the “Report”) shall be issued in confidence to the Clients and the Report will be strictly treated as such by the Company. It may not be reproduced either in its entirety or in part and it may not be used for advertising or other unauthorized purposes without the written consent of the Company. The Clients to whom the Report is issued may, however, show or send it, or a certified copy thereof prepared by the Company to its customer, supplier or other persons directly concerned. The Company will not, without the consent of the Clients, enter into any discussion or correspondence with any third party concerning the contents of the Report, unless required by the relevant governmental authorities, laws or court orders. 3.The Company shall not be called or be liable to be called to give evidence or testimony on the Report in a court of law without its prior written consent, unless required by the relevant governmental authorities, laws or court orders. 4. In the event of the improper use of the report as determined by the Company, the Company reserves the right to withdraw it, and to adopt any other additional remedies which may be appropriate. 5. Samples submitted for testing are accepted on the understanding that the Report issued cannot form the basis of, or be the instrument for, any legal action against the Company. 6. The Company will not be liable for or accept responsibility for any loss or damage however arising from the use of …

Text truncated - open the document above for the full version.