2A45C-KT11Wireless Power Bank

Input Cable Type-C Name: Wireless Power Bank Model NO.: KT11 Battery Type: Lithium Polymer Material: ABS + PC USB-C port input: 5VDC,3A/9VDC,2A Lightning input: 5VDC, 2A USB-C port output: 5VDC, 2A/9VDC,2.2A 12VDC, 1.67A USB-C wire output: 5VDC, 2A USB-A output: 5VDC, 2A Total output: 5VDC,3A(15W Max.) Wireless charging output: 15W Max. Battery Capacity:10000mAh(3.85V 38.5Wh) Rated Capacity: 6000mAh(5VDC,2A) Energy Conversion≥60% Product size: 104x71x19mm (4.09x2.80x0.74 inch) Net Weight: 197g/0.43lb Instructions Manual 16. Operating temperature should be between 10°C to 45°C / 50°F to 113°F 17. Storage Temperature range: -10 to 60 18. When disposing of secondary cells or batteries, keep cells or batteries of differnet electronchemical systems separate from each other. INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS IMPORTANT SAFETY INSTRUCTIONS WARNING – When using this product, basic precautions should always be followed, including the following: a) Read all the instructions before using the product. b) To Reduce the Risk of Injury, close supervision is necessary when the product is used near children. c) Do not put fingers or hands into the product. d) Do not expose power bank to rain or snow. e) Do not expose power bank to heat or fire. Do not store in direct sunlight or in a vehicle. f) Use of a power supply or charger not recommended or sold by power bank manufacturer may result in a risk of fire or injury to persons. g) Do not use the power bank in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury to persons. h) Do not use the power bank that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury. i) Do not disassemble the power bank. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury to persons. i) Do not expose a power bank to fire or excessive temperature. Exposure to fire or temperature above 45 ºC can be replaced by the temperature of 113°F. k) Have servicing performed by a qualified service or repair person using only identical replacement parts. This will ensure that the safety of the product is maintained. l) Switch off the power bank when not in use. SAVE THESE INSTRUCTIONS CAUTION:Risk of Fire and Burns.Do Not Open,Crush,Heat Above(45)or Incinerate.Follow Manufacturer's Instructions. Model NO.: KT11 FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. WIRELESS POWER BANK

Shenzhen Zhilianxintong Electronics Co., Ltd Room201, NO.49 Xinhe Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen 518111 China Date:07-07-2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A45C-KT11 FRN: 0032029126 US Agent – Attestation Statement / Part 2.911(d)(7) Shenzhen Zhilianxintong Elec tronics Co., Ltd certifies, that as of 07-07-2026, we have designated FCC US Agent, LLC to accept service of p rocess on our behalf for FCC ID: 2A45C- KT11 Shenzhen Zhilianxintong Electronics Co., Ltd, accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. FCC US Agent, LLC, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of Shenzhen Zhilianxintong Electronics Co., Ltd for FCC ID: 2A45C-KT11 Designated Agent Information: Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: [email protected] Sincerely, Shenzhen Zhilianxintong Electronics Co., Ltd Designated Agent: FCC US Agent, LLC Company Representative: Feng Shan Cui Designated Agent Representative: Tim Payne Signature: Signature:

ShenzhenZhilianxintongElectronicsCo.,Ltd date:06-17-2026 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(i)requestfor(FCCID:2A45C-KT11) [ShenzhenZhilianxintongElectronicsCo.,Ltd](“theapplicant”)certifiesthatthe equipmentforwhichauthorizationissoughtisnot“covered”equipmentprohibited fromreceivinganequipmentauthorizationpursuanttosection2.903oftheFCCrules. Wealsocertifythat,asofthedateofthefilingoftheapplication,theequipmentdoes notutilizecyber-securityoranti-virussoftwarefromKasperskyLab,Inc,oranyofits successorsandassignees,whichisalsoonthe“coveredlist”. Sincerely, Applicantsignature FengShanCui GeneralManager ShenzhenZhilianxintongElectronicsCo.,Ltd ShenzhenZhilianxintongElectronicsCo.,Ltd date:06-17-2026 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(ii)requestfor(FCCID:2A45C-KT11) [ShenzhenZhilianxintongElectronicsCo.,Ltd](“theapplicant”)certifiesthat,asofthe dateofthefilingoftheapplication,theapplicantisnotidentifiedontheCoveredListas anentityproducing“covered”equipment. Sincerely, (Applicantsignature FengShanCui GeneralManager ShenzhenZhilianxintongElectronicsCo.,Ltd

ShenzhenZhilianxintongElectronicsCo.,Ltd FCCID:2A45C-KT11 POWEROFATTORNEY Date:JUN.17,2026 FederalCommunicationsCommission AuthorizationandEvaluationDivision 7435OaklandMillsRoad Columbia,MD21046 ToWhomItMayConcern: We,theundersigned,herebyauthorizeWaltekTestingGroupCo.,Ltd.(DevalQin) onourbehalf,toapplytotheFederalCommunicationsCommissiononour equipment.AnyandallactscarriedoutbyWaltekTestingGroupCo.,Ltd.(Deval Qin)onourbehalfshallhavethesameeffectasactsofourown.This authorizationexpiresonJUN.16,2027. Sincerely, ShenzhenZhilianxintongElectronicsCo.,Ltd Signature FengShanCui/GeneralManager TypednameandTitle

ShenzhenZhilianxintongElectronicsCo.,Ltd Date:JUN.17,2026 FederalCommunicationsCommission AuthorizationandEvaluationDivision ConfidentialityRequestregardingapplicationforcertificationofFCCID:2A45C-KT11 PursuanttoSections0.457and0.459oftheCommission’sRules,weherebyrequestconfidential treatmentofinformationaccompanyingthisapplicationasoutlinedbelow: ExhibitTypeFileName Long-termconfidentiality: Schematics BlockDiagram OperationalDescription Schematics.pdf BlockDiagram.pdf OperationalDescription.pdf Theabovematerialscontaintradesecretsandproprietaryinformationnotcustomarilyreleasedto thepublic.Thepublicdisclosureofthesematerialsmaybeharmfultotheapplicantandprovide unjustifiedbenefitstoitscompetitors. TheapplicantunderstandsthatpursuanttoSection0.457oftheRules,disclosureofthis applicationandallaccompanyingdocumentationwillnotbemadebeforethedateoftheGrant forthisapplication. Sincerely, ShenzhenZhilianxintongElectronicsCo.,Ltd Signature FengShanCui/GeneralManager TypednameandTitle

ShenzhenZhilianxintongElectronicsCo.,Ltd FCCID:2A45C-KT11 Date:7/7/26 Subject:authorizationforaddingfamilymodels TowhomitMayconcern, Statement WeconfirmtheproductWirelessPowerBankwithmodelsKT11,KT20,ZL11,ZL20,XT01, XT02,WE00,KT-D011,KT-D020aresameintheSchematic,PCBlayout,Operation description,BOMandAntenna.Onlythemodelsnameisdifferent. Yourssincerely, [signature] FengShanCui GeneralManager ShenzhenZhilianxintongElectronicsCo.,Ltd

Appendix- KT11-Photos Reference No.: WTD26D05132519WPage 4 of 10 2. Photographs –Constructional Details 2.1. EUT – External View Model KT11 FCC ID: 2A45C-KT11 Appendix- KT11-Photos Reference No.: WTD26D05132519WPage 5 of 10 Appendix- KT11-Photos Reference No.: WTD26D05132519WPage 6 of 10 Appendix- KT11-Photos Reference No.: WTD26D05132519WPage 7 of 10

Label and Label Location Label: Label Location: Reverse side Made in China Name: Wireless Power Bank Model: KT11Battery Type: Lithium Polymer FCC ID:2A45C-KT11 USB-C port input: 5VDC, 3A / 9VDC, 2A Lightning input: 5VDC, 2A USB-C port output: 5VDC, 2A / 9VDC, 2.2A / 12VDC, 1.67A USB-C wire output: 5VDC, 2A USB-A output: 5VDC, 2A Wireless charging output: 15W Max. Total output: 5VDC,3A(15W Max.) Battery Capacity: 10000mAh3.85V 38.5Wh Rated Capacity: 6000mAh(5VDC,2A) Energy Conversion≥60% Manufacturer: Shenzhen Zhilianxintong Electronics Co., Ltd Address: Room201,NO.49 Xinhe Road, Shangmugu Community, Pinghu Street,Longgang District,Shenzhen, China CAUTION: Risk of Fire and Burns. Do Not Open, Crush, Heat Above(45) or Incinerate. Follow Manufacturer’s Instructions. ATTENTION : Risque d'incendie et de brûlures. Ne pas ouvrir, écraser, chauer au-dessus de (45) ou incinérer. Suivre les instructions du fabricant.

Appendix- KT11-Photos Reference No.: WTD26D05132519WPage 8 of 10 2.2. EUT – Internal View Model KT11 FCC ID: 2A45C-KT11 Appendix- KT11-Photos Reference No.: WTD26D05132519WPage 9 of 10 ANT Appendix- KT11-Photos Reference No.: WTD26D05132519WPage 10 of 10 ======End======

Waltek Testing Group Co., Ltd. http://www.waltek.com.cn Page 1 of 13 TEST REPORT Reference No. .................... : WTD26D05132519W003 FCC ID ................................ : 2A45C-KT11 Applicant ............................ : Shenzhen Zhilianxintong Electronics Co., Ltd Address .............................. : Room201, NO.49 Xinhe Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen 518111 China Manufacturer .................... : Shenzhen Zhilianxintong Electronics Co., Ltd Address .............................. : Room201, NO.49 Xinhe Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen 518111 China Product ............................... : Wireless Power Bank Model(s). ............................ : KT11, KT20, ZL11, ZL20, XT01, XT02, WE00, KT-D011, KT-D020 Standards........................... : FCC 47CFR Part 1.1307 Date of Receipt Sample .... : 2026-05-19 Date of Test ....................... : 2026-05-25 to 2026-06-04 Date of Issue ...................... : 2026-07-08 Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the si gnatures of compiler and approver. Prepared By: Waltek Testing Group Co., Ltd. Address: No. 77, Houjie Section, Guantai Road, Houjie Town, Dongguan City, Guangdong, China Tel: +86-769-2267 6998 Fax: +86-769-2267 6828 Compiled by: Approved by: Frank Yin / Project Engineer Deval Qin / Designated Reviewer Reference No.: WTD26D05132519W003 Page 2 of 13 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 2 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 CONTENTS ............................................................................................................................................... 2 3 REVISION HISTORY ................................................................................................................................. 3 4 GENERAL INFORMATION ....................................................................................................................... 4 4.1 GENERAL DESCRIPTION OF E.U.T ................................................................................................... 4 4.2 DETAILS OF ACCESSORIES ............................................................................................................... 4 4.3 TEST FACILITY ................................................................................................................................ 5 4.4 SUBCONTRACTED ........................................................................................................................... 5 4.5 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................ 5 4.6 TEST MODE .................................................................................................................................... 6 5 TEST SUMMARY ...................................................................................................................................... 7 6 EQUIPMENT USED DURING TEST ......................................................................................................... 8 6.1 EQUIPMENTS LIST ........................................................................................................................... 8 6.2 DESCRIPTION OF AUXILIARY EQUIPMENT .......................................................................................... 8 6.3 TEST EQUIPMENT CALIBRATION ....................................................................................................... 8 7 RF EXPOSURE ......................................................................................................................................... 9 7.1 EUT OPERATION ............................................................................................................................ 9 7.2 TEST SETUP ................................................................................................................................... 9 7.3 FIELD STRENGTH MEASUREMENTS ................................................................................................ 10 7.4 MATHEMATICAL MODEL .................................................................................................................. 10 7.5 FCC RULES.................................................................................................................................. 11 7.6 TEST RESULT ............................................................................................................................... 12 8 PHOTOGRAPHS OF TEST SETUP ....................................................................................................... 13 Reference No.: WTD26D05132519W003 Page 3 of 13 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 3 Revision History Test Report No. Date of Receipt Sample Date of Test Date of Issue Purpose CommentApproved WTD26D05132519W003 2026-05-19 2026-05-25 to 2026-06-04 2026-07-08 Original - Valid Reference No.: WTD26D05132519W003 Page 4 of 13 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 4 General Information 4.1 General Description of E.U.T Product: Wireless Power Bank Model(s): KT11, KT20, ZL11, ZL20, XT01, XT02, WE00, KT-D011, KT-D020 Model Description: Only the models name is different. Model KT11 was tested in this report. Test Sample No.: 1-1/1 Frequency Range: 110-148kHz Antenna installation: Inductive loop coil Antenna Hardware Version: K-D012U-V5.3 Software Version: K-D012-V4.2 4.2 Details of accessories Ratings: USB-C Port Input: 5VDC, 3A / 9VDC, 2A; Lightning Input: 5VDC, 2A USB-C Port Output: 5VDC, 2A /…

Text truncated - open the document above for the full version.

P r o d uc t s h a p e a n d s i z e P r o d uc t A pp e a r a n ce & D i m e n s i o n s S h e n z h e n J i n t i a n x i a T ec h n o l o g y C o . , LTD . P r o d uc t S p e c i f i c a t i o n A pp r o v a l C e r t i f i c a t e ( U n i t : mm ) ( N o t e : t h e p i c t u r e i s f o r r e f e r e n ce o n l y , t h e p r o d uc t i s su b j ec tt o t h e ac t u a l p r o d uc t . ) P ro d u c t e l e c t r i c a l c h ara c t er i s t i c s P ro d u c t e l e c t r i c a l c h ar ac t er i s t i c s n u m e r i c v a l ue ( V a l ue ) P ara m e t er ( P ar a m e t er ) : W i r e l e ss c h a r g i n g c o i l mo d u l e P ro d uc t na m e ( P r o d uc t na m e ) : D 4 3 0 5 A 11 - 60 K S TY ( C h i ne s e ) P r o d uc t n u m b er ( P r o d uc t n u m b e r ) : F er r i t e t y p e ( F e rr i t e t y p e ) : φ 4 3 . 5 * ① 5 * 0 . 8 m m ( w i t h t r o u g h ) N u m b er o f t u r n s i n t h e c o i l ( C o i l 1 0 T S T u r n s ) : M u l t i -s t ran d s i l k wrapp i ng w i re 0 . 08 * 7 2 P W i re t y p e ( C o il t y p e ) : 6 . 3 μ H ± 1 0 % I n d u c t a n ce ( I n d u c t a n ce ) : 4 0 ( M i n ) Q v a l u e ( Q V a l u e ) : D C r es i s t ance ( D C R ) 0 . 0 5 Ω ( M a x ) T e s t i n s t r u m e n t ( T es t i n g TH 28 1 6 B @ 1 0 0 k H z 、 1 V r ms ; T H 2 5 1 2 B A t 2 5 °C I n s t r u m e n t ) : S i n g l e - s i d e d or d i n ar y d ou b l e - s id e d a d h es i v e R e m a r k s ( N o t e ) : F o r m o r e i n f o rma t i o n , p l ease co n t ac t us ( C o n t a c t U s F o r M o r e I n f o rm a t i o n ) . Calculate outside the coil The coil surface is pasted with ordinary adhesive. Double-sided adhesive with ordinary adhesive backing.

Waltek Testing Group Co., Ltd. http://www.waltek.com.cn Page 1 of 26 TEST REPORT Reference No. .................... : WTD26D05132519W002 FCC ID ................................ : 2A45C-KT11 Applicant ............................ : Shenzhen Zhilianxintong Electronics Co., Ltd Address .............................. : Room201, NO.49 Xinhe Road, Shangmugu Community, Pinghu Street, Lon ggang District, Shenzhen 518111 China Manufacturer .................... : Shenzhen Zhilianxintong Electronics Co., Ltd Address .............................. : Room201, NO.49 Xinhe Road, Shangmugu Community, Pinghu Street, Lon ggang District, Shenzhen 518111 China Product ............................... : Wireless Power Bank Model(s). ............................ : KT11, KT20, ZL11, ZL20, XT01, XT02, WE00, KT-D011, KT-D020 Standards........................... : FCC 47CFR 15.209 Date of Receipt Sample .... : 2026-05-19 Date of Test ....................... : 2026-05-25 to 2026-06-04 Date of Issue ...................... : 2026-07-08 Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the si gnatures of compiler and approver. Prepared By: Waltek Testing Group Co., Ltd. Address: No. 77, Houjie Section, Guantai Road, Houjie Town, Dongguan City, Guangdong, China Tel: +86-769-2267 6998 Fax: +86-769-2267 6828 Compiled by: Approved by: Frank Yin / Project Engineer Deval Qin / Designated Reviewer Reference No.: WTD26D05132519W002 Page 2 of 26 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 2 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 CONTENTS ............................................................................................................................................... 2 3 REVISION HISTORY ................................................................................................................................. 3 4 GENERAL INFORMATION ....................................................................................................................... 4 4.1 GENERAL DESCRIPTION OF E.U.T ................................................................................................... 4 4.2 DETAILS OF ACCESSORIES ............................................................................................................... 4 4.3 TEST FACILITY ................................................................................................................................ 5 4.4 SUBCONTRACTED ........................................................................................................................... 5 4.5 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................ 5 4.6 TEST MODE .................................................................................................................................... 6 5 TEST SUMMARY ...................................................................................................................................... 7 6 EQUIPMENT USED DURING TEST ......................................................................................................... 8 6.1 EQUIPMENTS LIST ........................................................................................................................... 8 6.2 DESCRIPTION OF SUPPORT UNITS ................................................................................................... 9 6.3 MEASUREMENT UNCERTAINTY ......................................................................................................... 9 6.4 TEST EQUIPMENT CALIBRATION ....................................................................................................... 9 7 CONDUCTED EMISSION ....................................................................................................................... 10 7.1 EUT OPERATION .......................................................................................................................... 10 7.2 EUT SETUP .................................................................................................................................. 10 7.3 MEASUREMENT DESCRIPTION ........................................................................................................ 10 7.4 CONDUCTED EMISSION TEST RESULT ............................................................................................ 12 8 RADIATED SPURIOUS EMISSIONS ..................................................................................................... 14 8.1 EUT OPERATION .......................................................................................................................... 14 8.2 TEST SETUP ................................................................................................................................. 15 8.3 SPECTRUM ANALYZER SETUP ........................................................................................................ 16 8.4 TEST PROCEDURE ........................................................................................................................ 16 8.5 CORRECTED AMPLITUDE & MARGIN CALCULATION ......................................................................... 16 8.6 SUMMARY OF TEST RESULTS ........................................................................................................ 17 9 BANDWIDTH MEASUREMENT ............................................................................................................. 25 9.1 TEST PROCEDURE ........................................................................................................................ 25 9.…

Text truncated - open the document above for the full version.

Appendix- KT11-Photos Reference No.: WTD26D05132519WPage 1 of 10 1. Test Setup photos Model KT11 FCC ID: 2A45C-KT11 1.1 Photograph – Conducted Emission For Conducted Emission Test Site 1# 1.2 Photograph – Radiated Emissions For 9kHz-30MHz Test Site 2# Appendix- KT11-Photos Reference No.: WTD26D05132519WPage 2 of 10 For 30MHz-1000MHz Test Site 2# 1.3 Photograph – RF Exposure 6cm Appendix- KT11-Photos Reference No.: WTD26D05132519WPage 3 of 10 8cm 10cm