2A45C-PA09Wireless Power Bank

Lightning Input Port Power Button 16. Operating temperature should be between 10°C to 35°C / 50°F to 95°F 17. Storage Temperature range: -10 to 60 18. When disposing of secondary cells or batteries, keep cells or batteries of differnet electronchemical systems separate from each other. INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY TO PERSONS IMPORTANT SAFETY INSTRUCTIONS WARNING – When using this product, basic precautions should always be followed,including the following: a) Read all the instructions before using the product. b) To reduce the risk of injury , close supervision is necessary when the product is used near children. c) Do not put fingers or hands into the product. d) Do not expose power bank to rain or snow. e) Do not expose power bank to heat or fire. Do not store in direct sunlight or in a vehicle. f) Use of a power supply or charger not recommended or sold by power pack manufacturer may result in a risk of fire or injury to persons. g) Do not use the power bank in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury to persons. h) Do not use the power bank that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury. i) Do not disassemble the power bank. Take it to a qualified service person when service or repair is required . Incorrect reassembly may result in a risk of fire or injury to persons. j) Do not expose a power pack to fire or excessive temperature. Exposure to fire or temperature above 45°C may cause explosion.The temperature of 45°C can be replaced by the temperature of 113°F. k) Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained. l) Switch off the power bank when not in use. SAVE THESE INSTRUCTIONS FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. such modifications could void the user's authority to operate the equipment. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. (5VDC,2A) Wireless charging output: 5W, 7.5W, 10W, 15W Total output: 5VDC,3A(15W Max .) Lightning input: 9VDC, 2A Type-C input: 5VDC, 3A / 9VDC, 2A Type-C output: 5VDC, 2A / 9VDC, 2.2A/9VDC, 2A USB output: 5VDC, 2A / 9VDC, 2.2A / 12VDC, 1.5A / 5VDC, 4.5A CAUTION: Risk of Fire and Burns. Do Not Open, Crush, Heat Above(45) or Incinerate. Follow Manufacturer’s Instructions. Pa09 Pa09 9 Battery Type: Lithium Polymer Product size: 104x68x21mm 4.09x2.68x0.86 inch Net weight: 189g/6.67oz

Shenzhen Zhilianxintong Electronics Co., Ltd Room201, NO.49 Xinhe Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen 518111 China Date:07-07-2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 FCC ID: 2A45C-PA09 FRN: 0032029126 US Agent – Attestation Statement / Part 2.911(d)(7) Shenzhen Zhilianxintong Electronics Co., Ltd certifies, that as of 07-07-2026, we have designated FCC US Agent, LLC to accept service of process on our behalf for FCC ID: 2A45C- PA09 Shenzhen Zhilianxintong Electronics Co., Ltd, accepts to maintain an agent of service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. FCC US Agent, LLC, accepts as of the date of the filing of this application, the obligation of being the designated agent for the purpose of accepting service of process on behalf of Shenzhen Zhilianxintong Electronics Co., Ltd for FCC ID: 2A45C-PA09 Designated Agent Information: Company Name: FCC US Agent, LLC FRN: 0033402884 Address: 3722 Illinois Avenue, Saint Charles, IL, 60174, USA Contact Person: Tim Payne Phone: 708-571-3148 Email: [email protected] Sincerely, Shenzhen Zhilianxintong Electronics Co., Ltd Designated Agent: FCC US Agent, LLC Company Representative: Feng Shan Cui Designated Agent Representative: Tim Payne Signature: Signature:

ShenzhenZhilianxintongElectronicsCo.,Ltd date:06-17-2026 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(i)requestfor(FCCID:2A45C-PA09) [ShenzhenZhilianxintongElectronicsCo.,Ltd](“theapplicant”)certifiesthatthe equipmentforwhichauthorizationissoughtisnot“covered”equipmentprohibited fromreceivinganequipmentauthorizationpursuanttosection2.903oftheFCCrules. Wealsocertifythat,asofthedateofthefilingoftheapplication,theequipmentdoes notutilizecyber-securityoranti-virussoftwarefromKasperskyLab,Inc,oranyofits successorsandassignees,whichisalsoonthe“coveredlist”. Sincerely, Applicantsignature FengShanCui GeneralManager ShenzhenZhilianxintongElectronicsCo.,Ltd ShenzhenZhilianxintongElectronicsCo.,Ltd date:06-17-2026 EurofinsElectricalandElectronicTestingNA,Inc. 914WestPatapscoAvenue Baltimore,MD21230 RE:AttestationStatementsPart2.911(d)(5)(ii)requestfor(FCCID:2A45C-PA09) [ShenzhenZhilianxintongElectronicsCo.,Ltd](“theapplicant”)certifiesthat,asofthe dateofthefilingoftheapplication,theapplicantisnotidentifiedontheCoveredListas anentityproducing“covered”equipment. Sincerely, (Applicantsignature FengShanCui GeneralManager ShenzhenZhilianxintongElectronicsCo.,Ltd

Shenzhen Zhilianxintong Electronics Co., Ltd FCC ID: 2A45C-PA09 POWER OF ATTORNEY Date: JUN. 17, 2026 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: We, the undersigned, hereby authorize Waltek Testing Group Co., Ltd. (Deval Qin) on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group Co., Ltd. (Deval Qin) on our behalf shall have the same effect as acts of our own. This authorization expires onJUN. 16, 2027. Sincerely, Shenzhen Zhilianxintong Electronics Co., Ltd Signature Feng Shan Cui / General Manager Typed name and Title

ShenzhenZhilianxintongElectronicsCo.,Ltd Date:JUN.17,2026 FederalCommunicationsCommission AuthorizationandEvaluationDivision ConfidentialityRequestregardingapplicationforcertificationofFCCID:2A45C-PA09 PursuanttoSections0.457and0.459oftheCommission’sRules,weherebyrequestconfidential treatmentofinformationaccompanyingthisapplicationasoutlinedbelow: ExhibitTypeFileName Long-termconfidentiality: Schematics BlockDiagram OperationalDescription Schematics.pdf BlockDiagram.pdf OperationalDescription.pdf Theabovematerialscontaintradesecretsandproprietaryinformationnotcustomarilyreleasedto thepublic.Thepublicdisclosureofthesematerialsmaybeharmfultotheapplicantandprovide unjustifiedbenefitstoitscompetitors. TheapplicantunderstandsthatpursuanttoSection0.457oftheRules,disclosureofthis applicationandallaccompanyingdocumentationwillnotbemadebeforethedateoftheGrant forthisapplication. Sincerely, ShenzhenZhilianxintongElectronicsCo.,Ltd Signature FengShanCui/GeneralManager TypednameandTitle

ShenzhenZhilianxintongElectronicsCo.,Ltd FCCID:2A45C-PA09 Date:7/7/26 Subject:authorizationforaddingfamilymodels TowhomitMayconcern, Statement WeconfirmtheproductWirelessPowerBankwithmodelsPa09,KT-D009,KT-D001,KT-D022, KT-D013,KT-D003,KT-D009I,KT-D003I,KT-D001I,Tuo03,Xun01aresameintheSchematic, PCBlayout,Operationdescription,BOMandAntenna.Onlythemodelsnameisdifferent. Yourssincerely, [signature] FengShanCui GeneralManager ShenzhenZhilianxintongElectronicsCo.,Ltd

Appendix- Pa09-Photos Reference No.: WTD26D05132520WPage 4 of 10 2. Photographs –Constructional Details 2.1. EUT – External View Model Pa09 FCC ID: 2A45C-PA09 Appendix- Pa09-Photos Reference No.: WTD26D05132520WPage 5 of 10 Appendix- Pa09-Photos Reference No.: WTD26D05132520WPage 6 of 10 Appendix- Pa09-Photos Reference No.: WTD26D05132520WPage 7 of 10

Label Location： Label and Label Location Cet appareil, ses piles et cordons se recyclent À DÉPOSER EN MAGASIN À DÉPOSER EN DÉCHÈTERIE Made in China Rated capacity:6000mAh Energy conversion:≥60% 3.85V 38.5Wh FCC ID:2A45C-KT-D003 U VAT SPEED SL Calle Antonio Salvador N99.1,28026 Madrid,Spain [email protected] Cet appareil, ses piles et cordons se recyclent À DÉPOSER EN MAGASIN À DÉPOSER EN DÉCHÈTERIE Made in China Manufacturer: Shenzhen Zhilianxintong Electronics Co.,Ltd Address: Room201,NO.49 Xinhe Road, Shangmugu Community, Model NO.: Pa09 FCC ID:2A45C- PA09 Pinghu Street,Longgang District,Shenzhen, China USB output: 5VDC, 2A/9VDC, 2.2A/12VDC, 1.5A/5VDC, 4.5A Lightning input: 9VDC, 2A Type-C output: 5VDC, 2A/9VDC, 2.2A/9VDC, 2A Type-C input: 5VDC, 3A/9VDC, 2A Wireless charging output: 5W, 7.5W, 10W, 15W. Total output: 5VDC,3A(15W Max.) Battery capacity: 10000mAh 3.85V 38.5Wh Battery Type: Lithium Polymer Rated capacity:6000mAh(5VDC, 2A) Energy conversion:≥60% CAUTION: Risk of Fire and Burns. Do Not Open, Crush, Heat Above(45) or Incinerate. Follow Manufacturer’s Instructions. ATTENTION : Risque d'incendie et de brûlures. Ne pas ouvrir, écraser, chauer au-dessus de (45) ou incinérer. Suivre les instructions du fabricant. Label

Appendix- Pa09-Photos Reference No.: WTD26D05132520WPage 8 of 10 2.2. EUT – Internal View Model Pa09 FCC ID: 2A45C-PA09 Appendix- Pa09-Photos Reference No.: WTD26D05132520WPage 9 of 10 ANT Appendix- Pa09-Photos Reference No.: WTD26D05132520WPage 10 of 10 ======End======

Waltek Testing Group Co., Ltd. http://www.waltek.com.cn Page 1 of 13 TEST REPORT Reference No. .................... : WTD26D05132520W003 FCC ID ................................ : 2A45C-PA09 Applicant ............................ : Shenzhen Zhilianxintong Electronics Co., Ltd Address .............................. : Room201, NO.49 Xinhe Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen 518111 China Manufacturer .................... : Shenzhen Zhilianxintong Electronics Co., Ltd Address .............................. : Room201, NO.49 Xinhe Road, Shangmugu Community, Pinghu Street, Longgang District, Shenzhen 518111 China Product ............................... : Wireless Power Bank Model(s). ............................ : Pa09, KT-D009, KT-D001, KT-D022, KT-D013, KT-D003, KT-D009I, KT-D003I, KT-D001I, Tuo03, Xun01 Standards........................... : FCC 47CFR Part 1.1307 Date of Receipt Sample .... : 2026-05-19 Date of Test ....................... : 2026-05-25 to 2026-06-04 Date of Issue ...................... : 2026-07-08 Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the si gnatures of compiler and approver. Prepared By: Waltek Testing Group Co., Ltd. Address: No. 77, Houjie Section, Guantai Road, Houjie Town, Dongguan City, Guangdong, China Tel: +86-769-2267 6998 Fax: +86-769-2267 6828 Compiled by: Approved by: Frank Yin / Project Engineer Deval Qin / Designated Reviewer Reference No.: WTD26D05132520W003 Page 2 of 13 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 2 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 CONTENTS ............................................................................................................................................... 2 3 REVISION HISTORY ................................................................................................................................. 3 4 GENERAL INFORMATION ....................................................................................................................... 4 4.1 GENERAL DESCRIPTION OF E.U.T ................................................................................................... 4 4.2 DETAILS OF ACCESSORIES ............................................................................................................... 4 4.3 TEST FACILITY ................................................................................................................................ 5 4.4 SUBCONTRACTED ........................................................................................................................... 5 4.5 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................ 5 4.6 TEST MODE .................................................................................................................................... 6 5 TEST SUMMARY ...................................................................................................................................... 7 6 EQUIPMENT USED DURING TEST ......................................................................................................... 8 6.1 EQUIPMENTS LIST ........................................................................................................................... 8 6.2 DESCRIPTION OF AUXILIARY EQUIPMENT .......................................................................................... 8 6.3 TEST EQUIPMENT CALIBRATION ....................................................................................................... 8 7 RF EXPOSURE ......................................................................................................................................... 9 7.1 EUT OPERATION ............................................................................................................................ 9 7.2 TEST SETUP ................................................................................................................................... 9 7.3 FIELD STRENGTH MEASUREMENTS ................................................................................................ 10 7.4 MATHEMATICAL MODEL .................................................................................................................. 10 7.5 FCC RULES.................................................................................................................................. 11 7.6 TEST RESULT ............................................................................................................................... 12 8 PHOTOGRAPHS OF TEST SETUP ....................................................................................................... 13 Reference No.: WTD26D05132520W003 Page 3 of 13 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 3 Revision History Test Report No. Date of Receipt Sample Date of Test Date of Issue Purpose CommentApproved WTD26D05132520W003 2026-05-19 2026-05-25 to 2026-06-04 2026-07-08 Original - Valid Reference No.: WTD26D05132520W003 Page 4 of 13 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 4 General Information 4.1 General Description of E.U.T Product: Wireless Power Bank Model(s): Pa09, KT-D009, KT-D001, KT-D022, KT-D013, KT-D003, KT-D009I, KT- D003I, KT-D001I, Tuo03, Xun01 Model Description: Only the models name is different. Model Pa09 was tested in this report. Test Sample No.: 1-1/1 Frequency Range: 140-142.6kHz Antenna installation: Inductive loop coil Antenna Hardware Version: KD07-12C-V4.2 Software Version: KT-D07-V3.0 4.2 Details of accessories Ratings: USB Output: 5VDC, 2A…

Text truncated - open the document above for the full version.

P r o d uc t s h a p e a n d s i z e P r o d uc t A pp e a r a n ce & D i m e n s i o n s S h e n z h e n J i n t i a n x i a T ec h n o l o g y C o . , LTD . P r o d uc t S p e c i f i c a t i o n A pp r o v a l C e r t i f i c a t e ( U n i t : mm ) ( N o t e : t h e p i c t u r e i s f o r r e f e r e n ce o n l y , t h e p r o d uc t i s su b j ec tt o t h e ac t u a l p r o d uc t . ) P ro d u c t e l e c t r i c a l c h ara c t er i s t i c s P ro d u c t e l e c t r i c a l c h ar ac t er i s t i c s n u m e r i c v a l ue ( V a l ue ) P ara m e t er ( P ar a m e t er ) : W i r e l e ss c h a r g i n g c o i l mo d u l e P ro d uc t na m e ( P r o d uc t na m e ) : D 4 3 0 5 A 11 - 60 K S TY ( C h i ne s e ) P r o d uc t n u m b er ( P r o d uc t n u m b e r ) : F er r i t e t y p e ( F e rr i t e t y p e ) : φ 4 3 . 5 * ① 5 * 0 . 8 m m ( w i t h t r o u g h ) N u m b er o f t u r n s i n t h e c o i l ( C o i l 1 0 T S T u r n s ) : M u l t i -s t ran d s i l k wrapp i ng w i re 0 . 08 * 7 2 P W i re t y p e ( C o il t y p e ) : 6 . 3 μ H ± 1 0 % I n d u c t a n ce ( I n d u c t a n ce ) : 4 0 ( M i n ) Q v a l u e ( Q V a l u e ) : D C r es i s t ance ( D C R ) 0 . 0 5 Ω ( M a x ) T e s t i n s t r u m e n t ( T es t i n g TH 28 1 6 B @ 1 0 0 k H z 、 1 V r ms ; T H 2 5 1 2 B A t 2 5 °C I n s t r u m e n t ) : S i n g l e - s i d e d or d i n ar y d ou b l e - s id e d a d h es i v e R e m a r k s ( N o t e ) : F o r m o r e i n f o rma t i o n , p l ease co n t ac t us ( C o n t a c t U s F o r M o r e I n f o rm a t i o n ) . Calculate outside the coil The coil surface is pasted with ordinary adhesive. Double-sided adhesive with ordinary adhesive backing.

Waltek Testing Group Co., Ltd. http://www.waltek.com.cn Page 1 of 25 TEST REPORT Reference No. .................... : WTD26D05132520W002 FCC ID ................................ : 2A45C-PA09 Applicant ............................ : Shenzhen Zhilianxintong Electronics Co., Ltd Address .............................. : Room201, NO.49 Xinhe Road, Shangmugu Community, Pinghu Street, Lon ggang District, Shenzhen 518111 China Manufacturer .................... : Shenzhen Zhilianxintong Electronics Co., Ltd Address .............................. : Room201, NO.49 Xinhe Road, Shangmugu Community, Pinghu Street, Lon ggang District, Shenzhen 518111 China Product ............................... : Wireless Power Bank Model(s). ............................ : Pa09, KT-D009, KT-D001, KT-D022, KT-D013, KT-D003, KT-D009I, KT-D003I, KT-D001I, Tuo03, Xun01 Standards........................... : FCC 47CFR 15.209 Date of Receipt Sample .... : 2026-05-19 Date of Test ....................... : 2026-05-25 to 2026-06-04 Date of Issue ...................... : 2026-07-08 Test Result ......................... : Pass Remarks: The results shown in this test report refer only to the sample(s) tested, this test report cannot be reproduced, except in full, without prior written permission of the company. The report would be invalid without specific stamp of test institute and the si gnatures of compiler and approver. Prepared By: Waltek Testing Group Co., Ltd. Address: No. 77, Houjie Section, Guantai Road, Houjie Town, Dongguan City, Guangdong, China Tel: +86-769-2267 6998 Fax: +86-769-2267 6828 Compiled by: Approved by: Frank Yin / Project Engineer Deval Qin / Designated Reviewer Reference No.: WTD26D05132520W002 Page 2 of 25 Waltek Testing Group Co., Ltd. http://www.waltek.com.cn 2 Contents Page 1 COVER PAGE ........................................................................................................................................... 1 2 CONTENTS ............................................................................................................................................... 2 3 REVISION HISTORY ................................................................................................................................. 3 4 GENERAL INFORMATION ....................................................................................................................... 4 4.1 GENERAL DESCRIPTION OF E.U.T ................................................................................................... 4 4.2 DETAILS OF ACCESSORIES ............................................................................................................... 4 4.3 TEST FACILITY ................................................................................................................................ 5 4.4 SUBCONTRACTED ........................................................................................................................... 5 4.5 ABNORMALITIES FROM STANDARD CONDITIONS ................................................................................ 5 4.6 TEST MODE .................................................................................................................................... 6 5 TEST SUMMARY ...................................................................................................................................... 7 6 EQUIPMENT USED DURING TEST ......................................................................................................... 8 6.1 EQUIPMENTS LIST ........................................................................................................................... 8 6.2 DESCRIPTION OF SUPPORT UNITS ................................................................................................... 9 6.3 MEASUREMENT UNCERTAINTY ......................................................................................................... 9 6.4 TEST EQUIPMENT CALIBRATION ....................................................................................................... 9 7 CONDUCTED EMISSION ....................................................................................................................... 10 7.1 EUT OPERATION .......................................................................................................................... 10 7.2 EUT SETUP .................................................................................................................................. 10 7.3 MEASUREMENT DESCRIPTION ........................................................................................................ 10 7.4 CONDUCTED EMISSION TEST RESULT ............................................................................................ 11 8 RADIATED SPURIOUS EMISSIONS ..................................................................................................... 13 8.1 EUT OPERATION .......................................................................................................................... 13 8.2 TEST SETUP ................................................................................................................................. 14 8.3 SPECTRUM ANALYZER SETUP ........................................................................................................ 15 8.4 TEST PROCEDURE ........................................................................................................................ 15 8.5 CORRECTED AMPLITUDE & MARGIN CALCULATION ......................................................................... 15 8.6 SUMMARY OF TEST RESULTS ........................................................................................................ 16 9 BANDWIDTH MEASUREMENT ............................................................................................................. 24 9.1 TEST PROCEDURE ...........................................................................................…

Text truncated - open the document above for the full version.

Appendix- Pa09-Photos Reference No.: WTD26D05132520WPage 1 of 10 1. Test Setup photos Model Pa09 FCC ID: 2A45C-PA09 1.1 Photograph – Conducted Emission For Conducted Emission Test Site 1# 1.2 Photograph – Radiated Emissions For 9kHz-30MHz Test Site 2# Appendix- Pa09-Photos Reference No.: WTD26D05132520WPage 2 of 10 For 30MHz-1000MHz Test Site 2# 1.1 Photograph – RF Exposure 6cm Appendix- Pa09-Photos Reference No.: WTD26D05132520WPage 3 of 10 8cm 10cm