2A64B-DEX35Floor Cleaning Robot

86ES-LA 3� Gire la parte superior y retire el ltro� 4� Gire la estructura de múltiples conos para desenroscarla� Nota: No se recomienda lavar la estructura de múltiples conos� Si es necesario, puede limpiarla con un paño húmedo y dejarla secar al aire� Nota: Asegúrese de secar al aire el recipiente para polvo antes de volver a utilizarlo� Nota: Seque completamente el filtro antes del uso� 5� Enjuague el recipiente con agua o límpielo con un paño húmedo� 6� Enjuague el recipiente para polvo y el ltro de esponja con agua y séquelos� 87ES-LA 2� Retire la cubeta para lavado de la mopa� Presione el pestillo de la cubeta para desmontar el ltro y limpiarlo� 2 Mantenimiento de la cubeta para lavado de la mopa 1� Retire y limpie la base de la estación� 88ES-LA 3� Vuelva a instalar el ltro de lavado de la mopa, la bandeja y la base de la estación en el orden correcto� Un sonido de "clic" indica que están bien colocados� Clic Tenga en cuenta que DEEBOT no se puede cargar cuando está apagado� Cargue completamente el DEEBOT y apáguelo antes de guardarlo� Recargue cada mes y medio para evitar que la batería se descargue en exceso� Nota: • Una vez que el DEEBOT termina su tarea de limpieza, se recomienda no apagarlo sino mantenerlo cargando para prepararlo para la siguiente sesión de limpieza� • Si la batería se descarga en exceso o no se utiliza durante mucho tiempo, es posible que el DEEBOT no se cargue� Póngase en contacto con ECOVACS para obtener asistencia� No desensamble la batería usted mismo� • Si no utiliza DEEBOT durante un periodo prolongado, utilice la función de reubicación del dispositivo de la aplicación para vaciar el agua limpia del interior de DEEBOT, mantenga vacíos los depósitos de agua de la estación y las mopas de rodillo secas� 4 Almacenamiento Iｏ Nota: Monte la cubeta y la base correctamente para evitar una falla de funcionamiento� 89ES-LA Para los siguientes posibles problemas, consulte las soluciones correspondientes� No. Falla de funcionamiento Posible causa Solución 1 DEEBOT no puede conectarse a la aplicación ECOVACS HOME� Se introdujo un nombre de usuario o contraseña de Wi-Fi incorrectos� Introduzca el nombre de usuario y la contraseña Wi-Fi correctos� DEEBOT no está dentro del alcance de la señal Wi-Fi de su casa� Asegúrese de que DEEBOT está dentro del alcance de la señal Wi-Fi de su casa� Intente mantenerse lo más cerca posible del enrutador� DEEBOT no está en estado de configuración� Pulse el botón RESET para conectar DEEBOT a su teléfono por Bluetooth� Si falla, pulse el botón RESET + y conéctese a través de la aplicación ECOVACS HOME� El Wi-Fi de la casa no está en la lista de Wi-Fi� Compruebe si el nombre del Wi-Fi contiene caracteres especiales� ¡No utilice caracteres especiales como! @#& ¥%/\� No utilice una red de 5 GHz� Se ha instalado una aplicación incorrecta�Descargue e instale la aplicación ECOVACS HOME� 2 No se puede crear el mapa de muebles en la aplicación� Mover el DEEBOT al limpiar puede hacer que se pierda el mapa� Durante la limpieza, no mueva el DEEBOT� La limpieza automática no ha terminado� Asegúrese de que el DEEBOT vuelve automáticamente a la estación OMNI después de la limpieza� El modo de varios pisos no estaba activado al crear el segundo mapa� Active el modo de varios pisos en la aplicación� 3 El cepillo lateral se sale de su lugar durante el uso� El cepillo lateral no está bien montado� Al montar el cepillo lateral con un destornillador, asegúrese de que el tornillo esté bien apretado� 4 No hay señal� No puede volver a la estación� La estación OMNI está mal colocada� Coloque la estación correctamente según las instrucciones de la sección [Encendido y carga del DEEBOT] � La estación está fuera de servicio o ha sido trasladada� Compruebe si la estación OMNI está conectada a la red eléctrica� No mueva la estación OMNI� DEEBOT no inicia la limpieza desde la estación OMNI�Se recomienda que DEEBOT inicie la limpieza desde la estación OMNI� La ruta de atraque está bloqueada� Por ejemplo, está cerrada la puerta a la habitación en la cual está la estación� Mantenga despejada la ruta de carga� RESOLUCIÓN DE PROBLEMAS 90ES-LA No. Falla de funcionamiento Posible causa Solución 5 DEEBOT vuelve a la estación OMNI antes de haber terminado la limpieza� La habitación es tan grande que DEEBOT necesita volver para recargarse� Habilite la reanudación automática� Por más detalle, siga las instrucciones de la aplicación� Cuando la distribución del hogar es muy compleja la eficacia de la limpieza puede disminuir, lo cual puede dar lugar a una limpieza incompleta� Simplifique la distribución de su casa� 6 DEEBOT no puede cargar� DEEBOT no está encendido�Encienda el DEEBOT� Los contactos de carga del DEEBOT no están conectados a los contactos de carga de la estación OMNI� Asegúrese de que los contactos de carga del DEEBOT se han conectado a los contactos de carga de la estación y que parpadea� Compruebe si los contactos de carga del DEEBOT y de la estación OMNI están sucios� Limpie estas piezas siguiendo las instrucciones de la sección [MANTENIMIENTO PERIÓDICO] � La estación OMNI no está conectada a la red eléctrica� 1� Asegúrese de que la estación OMNI esté conectada a la red eléctrica� 2� Una vez conectada la alimentación, asegúrese de que se oye el sonido de arranque del motor� La base no se ha instalado en su sitio� Consulte en la sección [Inicio rápido] cómo es la instalación correcta� 7 DEEBOT hace mucho ruido durante la limpieza� El cepillo principal, el cepillo lateral o la mopa de rodillo están enredados, o el depósito de polvo está obstruido� Se recomienda limpiar periódicamente el cepillo principal, el cepillo lateral, el depósito de polvo, la mopa de rodillo, etc� DEEBOT está en modo de aspiración fuerte o en modo de máxima potencia de aspiración� Cambie al modo estándar o silencioso� El modo silencioso puede reducir el rendimiento de la limpieza� 8 DEEBOT se atasca mientras trabaja y se para� DEEBOT se enreda con objetos en el suelo (cables eléctri…

Text truncated - open the document above for the full version.

57FR-CA 2� Retirez le plateau de lavage de la serpillière� Appuyez sur le loquet du plateau pour détacher le ltre et nettoyez-le� 2 Entretenez le plateau de lavage de la serpillière 1� Retirez et nettoyez la base de la station� 58FR-CA 3� Réinstallez le ltre de lavage de la serpillière, le plateau et la base de la station dans l'ordre� Un bruit de « clic » indique qu'ils sont bien en place� Clic Veuillez noter que le DEEBOT ne peut pas se recharger lorsqu'il est éteint� Veuillez recharger complètement et éteindre le DEEBOT avant de le ranger� Veuillez le recharger tous les mois et demi pour éviter que la batterie ne se décharge trop� Remarque : • Une fois que le DEEBOT a terminé sa tâche de nettoyage, il est recommandé de ne pas l'éteindre, mais de le maintenir en recharge an de mieux se préparer à la prochaine séance de nettoyage� • Si la batterie est trop déchargée ou n'est pas utilisée pendant une période prolongée, le DEEBOT peut ne pas être rechargé� Veuillez contacter ECOVACS pour obtenir de l'aide� Ne démontez pas la batterie vous-même� • Si vous n'utilisez pas le DEEBOT sur une longue période, utilisez la fonction de relocalisation de l'appareil dans l'application pour vider l'eau propre à l'intérieur du DEEBOT� Gardez les réservoirs d'eau de la station vides et les serpillières à rouleau sèches� 4 Entreposage Iｏ Remarque : Veuillez installer correctement le plateau et la base pour éviter les dysfonctionnements� 59FR-CA Pour connaître le problème potentiel, consultez les solutions correspondantes� No. Dysfonctionnement Cause potentielle Solution 1 Le DEEBOT n'est pas en mesure de se connecter à l'application ECOVACS HOME� Nom d'utilisateur ou mot de passe de Wi-Fi incorrect saisi� Entrez le bon nom d'utilisateur et le bon mot de passe de Wi-Fi� Le DEEBOT n'est pas à portée du signal Wi-Fi de votre maison� Assurez-vous que le DEEBOT est à portée du signal Wi-Fi de votre maison� Essayez de rester le plus près possible du routeur� Le DEEBOT n'est pas dans l'état de conguration� Appuyez sur la touche RESET (Réinitialisation) pour connecter le DEEBOT à votre téléphone par Bluetooth� En cas d'échec, veuillez appuyer sur la touche RESET + et connectez-vous via l'application ECOVACS HOME� Il n'y a pas de Wi-Fi domestique sur la liste des Wi-Fi� Vériez si le nom du Wi-Fi contient des caractères spéciaux� Veuillez ne pas utiliser de caractères spéciaux comme ! @#& ¥%/\� N'utilisez pas de réseau 5 GHz� Une application incorrecte est installée�Veuillez télécharger et installer l'application ECOVACS HOME� 2 Impossible de créer la carte des meubles dans l'application� Le déplacement du DEEBOT lors du nettoyage peut entraîner la perte de la carte� Pendant le nettoyage, ne déplacez pas le DEEBOT� Le nettoyage automatique n'est pas terminé� Assurez-vous que le DEEBOT revient automatiquement à la station OMNI après le nettoyage� Le mode à étages multiples n'était pas activé lors de la création de la deuxième carte� Veuillez activer le mode à étages multiples dans l'application� 3 La brosse latérale se déplace hors de sa position pendant l'utilisation� La brosse latérale n'est pas correctement installée� Lorsque vous installez la brosse latérale avec un tournevis, assurez- vous que la vis est bien serrée� 4 Aucun signal trouvé� Impossible de retourner à la station� La station OMNI est mal placée� Placer la station correctement selon les instructions de la section [Allumer et recharger le DEEBOT] � La station est en panne d'électricité ou a été déplacée� Vériez si la station OMNI est connectée à l'alimentation électrique� Ne déplacez pas la station OMNI� Le DEEBOT ne commence pas à nettoyer à partir de la station OMNI� Il est recommandé que le DEEBOT commence à nettoyer à partir de la station OMNI� L'itinéraire d'amarrage est bloqué� Par exemple, la porte est fermée à la pièce où se trouve le poste� Gardez le chemin de recharge dégagé� DÉPANNAGE 60FR-CA No. Dysfonctionnement Cause potentielle Solution 5 Le DEEBOT retourne à la station OMNI avant d'avoir terminé le nettoyage� La pièce est si grande que DEEBOT doit revenir pour se recharger� Veuillez activer la reprise automatique� Pour plus de détails, veuillez suivre les instructions de l'application� Dans les aménagements de maison très complexes, l'efcacité du nettoyage peut diminuer, ce qui peut entraîner un nettoyage incomplet� Simpliez l'aménagement de votre maison� 6 Le DEEBOT n'est pas en mesure de se recharger� Le DEEBOT n'est pas activé�Allumez le DEEBOT� Les contacts de charge du DEEBOT ne sont pas connectés aux contacts de charge de la station OMNI� Assurez-vous que les contacts de charge du DEEBOT sont connectés aux contacts de recharge de la station et que clignote� Vériez si les contacts de charge du DEEBOT et de la station OMNI sont sales� Veuillez nettoyer ces pièces selon les instructions de la section [ENTRETIEN RÉGULIER]� La station OMNI n'est pas connectée à l'alimentation électrique� 1� Assurez-vous que la station OMNI est connectée à l'alimentation électrique� 2� Une fois l'alimentation branchée, assurez-vous que le son de démarrage du moteur peut être entendu� La base n'a pas été installée en place� Consultez la section [Démarrage rapide] pour une installation correcte� 7 Le DEEBOT est très bruyant pendant le nettoyage� La brosse principale, la brosse latérale ou la serpillière à rouleau est enchevêtrée, ou le bac à poussière est bloqué� Il est recommandé de nettoyer régulièrement la brosse principale, la brosse latérale, le bac à poussière, la serpillière à rouleau, etc� Le DEEBOT est en mode d'aspiration forte ou en mode de puissance d'aspiration maximale� Passez en mode standard ou silencieux� Le mode silencieux peut réduire la performance du nettoyage� 8 Le DEEBOT se bloque pendant le travail et s'arrête� Le DEEBOT est enchevêtré avec des objets sur le sol (ls électriques, rideaux, franges de tapis, etc�)� Le DEEBOT essaiera différentes façons de se libérer� Si ses tentatives échouent, retirez manuellement les ob…

Text truncated - open the document above for the full version.

27EN 3� Reinstall the mop washing lter, tray, and station base in order� A "click" sound indicates they are securely in place� Click Please note that DEEBOT cannot charge when powered OFF� Please fully charge and switch OFF DEEBOT before storage� Please recharge it every 1�5 months to prevent the battery from over-discharging� Note: • After DEEBOT finishes its cleaning task, it is recommended not to power it off but to keep it charging, to better prepare for the next cleaning session� • If the battery is over-discharged or not used for a long time, DEEBOT may not be charged� Please contact ECOVACS for help� Do not disassemble the battery by yourself� • If you do not use DEEBOT for a long time, use the Device Relocation feature in the App to drain the clean water inside DEEBOT, keep the station water tanks empty, and the roller mops dry� 4 Storage Iｏ Note: Please install the tray and base properly to prevent malfunction� 28EN For the following possible issue, refer to the corresponding solutions� No. Malfunction Possible Cause Solution 1 DEEBOT is not able to connect to the ECOVACS HOME App� Incorrect Wi-Fi username or password entered� Enter the correct Wi-Fi username and password� DEEBOT is not within range of your home Wi-Fi signal� Make sure DEEBOT is within range of your home Wi-Fi signal� Try to stay as close to the router as possible� DEEBOT is not in the configuration state� Press the Reset button to connect DEEBOT to your phone by Bluetooth� If it fails, please press the Reset button + and connect via the ECOVACS HOME App� There is no home Wi-Fi on the Wi-Fi list� Check if the Wi-Fi name contains special characters� Please do not use special characters like ! @#& ¥%/\� Do not use a 5 Ghz network� An incorrect App is installed�Please download and install the ECOVACS HOME App� 2 Unable to create the furniture map in the App� Moving DEEBOT when cleaning might cause the map to be lost� During cleaning, do not move DEEBOT� Auto cleaning is not finished� Make sure DEEBOT automatically returns to the OMNI Station after cleaning� Multi-floor mode was not enabled when the second map was created� Please enable multi-floor mode in the App� 3 The side brush drops out of place during use� The side brush is not properly installed� When installing the side brush with a screwdriver, ensure the screw is tightened securely� 4 No signal found� Unable to return to the station� The OMNI Station is incorrectly placed� Place the station properly according to the instructions in the [Power on and Charge DEEBOT] section� Station is out of power or has been moved� Check whether the OMNI Station is connected to the power supply� Do not move the OMNI Station� DEEBOT does not start cleaning from the OMNI Station� It is recommended that DEEBOT start cleaning from the OMNI Station� The docking route is blocked� For example, the door is closed to the room where the station is placed� Keep the charging route clear� TROUBLESHOOTING 29EN No. Malfunction Possible Cause Solution 5 DEEBOT returns to the OMNI Station before it has finished cleaning� The room is so large that DEEBOT needs to return to recharge� Please enable auto resume� For more details, please follow the App instructions� In highly complex home layouts, cleaning efficiency may decrease, possibly resulting in incomplete cleaning� Simplify your home layout� 6 DEEBOT is unable to charge� DEEBOT is not switched ON�Switch ON DEEBOT� DEEBOT's charging contacts are not connected to the OMNI station's charging contacts� Make sure that DEEBOT's charging contacts have connected to the station's charging contacts and flashes� Check whether DEEBOT's and OMNI station's charging contacts are dirty� Please clean these parts according to the instructions in the [REGULAR MAINTENANCE] section� The OMNI Station is not connected to the power supply� 1� Make sure the OMNI station is connected to power supply� 2� Once the power is connected, ensure that the motor startup sound can be heard� The base has not been installed in place�Refer to the [Quick Start] section for correct installation� 7 DEEBOT is very loud during cleaning� The main brush/side brush is tangled, or the dust bin/roller mop/filter is blocked� It is recommended to clean the main brush, side brush, dust bin, roller mop, filter, etc� regularly� DEEBOT is in Strong Suction Mode or Max Suction Power Mode� Switch to Standard or Quiet Mode� Quiet Mode may reduce cleaning performance� 8 DEEBOT gets stuck while working and stops� DEEBOT is tangled with objects on the floor (electrical wires, curtains, carpet fringing, etc�)� DEEBOT will try various ways to free itself� If its attempts fail, manually remove the obstacles and restart� DEEBOT might be stuck under furniture with an entrance of similar height� Please raise the furniture, set a physical barrier, or set a virtual boundary via the ECOVACS HOME App� DEEBOT is stuck in a narrow area� Tidy up your home, set a physical barrier, or set a virtual boundary via the ECOVACS HOME App� 30EN No. Malfunction Possible Cause Solution 9 During cleaning, DEEBOT may encounter issues like a disorderly route, biased movement, repeated cleaning over the same spots, and missing small areas� A large area has not been cleaned, possibly because it was blocked� Ensure the door is open, clear potential obstacles, such as slippers and scattered cords� DEEBOT will perform supplementary cleaning before the cleaning session is finished� The driving wheels may slip on the ground when DEEBOT climbs steps, thresholds, and door bars, which can affect its judgment of the entire home environment� Close the door of the room, or set a virtual boundary in the App� You can then bring DEEBOT into the room to clean it separately� On freshly waxed or polished floors, as well as smooth tiles, there may be less friction between the driving wheels and the floor� Please wait for the wax to dry before cleaning� 10 After returning to the OMNI station, DEEBOT does not empty its dust bin� The Auto-Empty…

Text truncated - open the document above for the full version.

Instruction Manual Instruction Manual �������������������������������������������������������������������������������������������EN I P03 Manuel d’instructions �������������������������������������������������������������������������������FR-CA I P33 Manual de instrucciones����������������������������������������������������������������������������ES-LA I P64 3EN 1� Do not allow to be used as a toy� Close attention is necessary when used by or near children� 2� Clear the area to be cleaned� Remove power cords and small objects from the oor that could entangle the Appliance� Tuck rug fringe under the rug base, and lift items such as curtains and tablecloths off the oor� 3� If there is a drop off in the cleaning area due to a step or stairs, you should operate the Appliance to ensure that it can detect the step without falling over the edge� It may become necessary to place a physical barrier at the edge to keep the unit from falling� Make sure the physical barrier is not a trip hazard� 4� Only use as described in this manual� Only use attachments recommended or sold by the manufacturer� 5� Do not handle plug or appliance with wet hands� 6� Non-rechargeable batteries are prohibited� 7� Do not use without Dust Bin and/or Filters in place� 8� Do not operate the vacuum in an area where there are lit candles or fragile objects on the oor to be cleaned� 9� Do not use and store in extremely hot or cold environments (below -5 ̊C /23 ̊F or above 40 ̊C/104 ̊F)� Please charge the robot in temperature above 0°C/32°F and below 40°C/104°F� 10� Keep hair, loose clothing, ngers, and all parts of body away from any openings and moving parts� 11� Do not operate the Appliance in a room where an infant or child is sleeping� 12� For INDOOR use ONLY� Do not use the Appliance in outdoor, commercial or industrial environments� Do not use Appliance on wet surfaces or surfaces with standing water� 13� Do not allow the Appliance to pick up large objects like stones, large pieces of paper, or any item that may clog the Appliance� 14� Do not use to pick up ammable or combustible IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. When using an electrical appliance, basic precautions should always be followed, including the following: WARNING: Read all safety warnings and instructions� Failure to follow the warnings and instructions may result in electric shock, fire, or serious injury� 4EN materials such as gasoline, printer, or copier toner, or use in areas where they may be present� 15� Do not pick up anything that is burning or smoking, such as cigarettes, matches, hot ashes, or anything that could cause a re� 16� Do not put any object into openings� Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air ow� 17� Take care not to damage the power cord� Do not pull on or carry the Appliance or Docking Station by the power cord, use the power cord as a handle, close a door on the power cord, or pull power cord around sharp edges or corners� Do not run Appliance and Docking Station over the power cord� Keep power cord away from hot surfaces� Do not unplug by pulling on cord� To unplug, grasp the plug, not the cord� 18� If the power cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard� 19� Do not use with a damaged power cord or plug� Do not use the Appliance or Docking Station if it is not working properly, has been dropped, damaged, left outdoors, or come in contact with water� It must be repaired by the manufacturer or its service agent in order to avoid a hazard� 20� Turn OFF the power switch before cleaning or maintaining the Appliance� Turn off all controls before unplugging� Always turn off this appliance before connecting or disconnecting motorized nozzle� 21� Turn OFF the Power Switch before removing the Dust Bin� 22� Remove the Appliance from the Docking Station, and turn OFF the power switch to the Appliance before removing the battery for disposal of the Appliance� 23� The battery must be removed and discarded according to local laws and regulations before disposal of the Appliance� 24� Please dispose of used batteries according to local laws and regulations� 25� Do not incinerate the Appliance even if it is severely damaged� The batteries can explode in a re� 26� When not using the Docking Station, unplug from outlet when not in use and before servicing� 27� The Appliance must be used in accordance with the directions in this Instruction Manual� Ecovacs Home Service Robotics cannot be held liable or responsible for any damages or injuries caused by improper use� 5EN 28� Prevent unintentional starting� Ensure the switch is in the off position before connecting to battery pack, picking up or carrying the appliance� 29� When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another� Shorting the battery terminals together may cause burns or a re� 30� Under abusive conditions, liquid may be ejected from the battery; avoid contact� If contact accidentally occurs, ush with water� If liquid contacts eyes, additionally seek medical help� Liquid ejected from the battery may cause irritation or burns� 31� Do not use a battery pack or appliance that is damaged or modied� Damaged or modied batteries may exhibit unpredictable behavior resulting in re, explosion, or risk of injury� 32� Do not expose a battery pack or appliance to re or excessive temperature� Exposure to re or temperature above 130°C may cause explosion� The temperature of 130°C can be replaced by the temperature of 265°F� 33� Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specied in the instructions� Charging improperly or at temperatures outside of the specied range may damage …

Text truncated - open the document above for the full version.

Ecovacs Home Service Robotics Co., Ltd. RF TEST REPORT Report Type: FCC Part 15.247 & ISED RSS-247 RF report Model: DEX35 REPORT NUMBER: 2512B1384SHA-001 ISSUE DATE: January 16, 2026 DOCUMENT CONTROL NUMBER: TTRF15.247-02_V1 © 2018 Intertek Intertek Testing Services (Shanghai FTZ) Co., Ltd. Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com TEST REPORT This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRF15.247-02_V1 © 2018 Intertek Page 2 of 32 Report no.: 2512B1384SHA-001 Applicant: Ecovacs Home Service Robotics Co., Ltd. No.518 Songwei Road,Wusongjiang industry Park, Guoxiang Street, Wuzhong District, Suzhou, Jiangsu, China. Manufacturer: Same as applicant Factory 1: Ecovacs Home Service Robotics Co., Ltd. No.518 Songwei Road, Wusongjiang industry Park, Guoxiang Street, Wuzhong District, Suzhou, Jiangsu, China. Factory 2: Competition Team Technology (Vietnam) Co.Ltd. Lot CN-05, Dong Mai Industrial Zone, Dong Mai ward, Quang Ninh province, Vietnam FCC ID: 2A64B-DEX35 IC: 28593-DEX35 SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: 47CFR Part 15 (2024): Radio Frequency Devices (Subpart C) ANSI C63.10 (2020) +Cor.1(2023) +C63.10a (2024) +Errata to C63.10a(2024): American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices RSS-247 Issue 4 (July 2025): Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and Licence- Exempt Local Area Network (LE-LAN) Devices RSS-Gen Issue 5 (April 2018) +A1(March 2019) +A2(February 2021): General Requirements for Compliance of Radio Apparatus PREPARED BY: REVIEWED BY: Project Engineer Eric Li Reviewer Wakeyou Wang Report No.: 2512B1384SHA-001 TEST REPORT TTRF15.247-02_V1 © 2018 Intertek Page 3 of 32 Content REVISION HISTORY................................................................................................................................................ 5 MEASUREMENT RESULT SUMMARY ..................................................................................................................... 6 1 GENERAL INFORMATION ............................................................................................................................. 7 1.1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ..................................................................................................... 7 1.2 TECHNICAL SPECIFICATION .................................................................................................................................... 7 1.3 DESCRIPTION OF TEST FACILITY .............................................................................................................................. 8 2 TEST SPECIFICATIONS ................................................................................................................................... 9 2.1 STANDARDS OR SPECIFICATION ............................................................................................................................... 9 2.2 MODE OF OPERATION DURING THE TEST ................................................................................................................... 9 2.3 TEST SOFTWARE LIST .......................................................................................................................................... 10 2.4 TEST PERIPHERALS LIST ....................................................................................................................................... 10 2.5 TEST ENVIRONMENT CONDITION: .......................................................................................................................... 10 2.6 INSTRUMENT LIST .............................................................................................................................................. 11 2.7 MEASUREMENT UNCERTAINTY ............................................................................................................................. 12 3 MINIMUM 6DB BANDWIDTH ..................................................................................................................... 13 3.1 LIMIT .............................................................................................................................................................. 13 3.2 MEASUREMENT PROCEDURE ............................................................................................................................... 13 3.3 TEST CONFIGURATION ........................................................................................................................................ 13 3.4 TEST RESULTS OF MINIMUM 6DB BANDWIDTH ....................................................................................................... 13 4 MAXIMUM CONDUCTED OUTPUT POWER AND E.I.R.P. ............................................................................. 14 4.1 LIMIT ....................................................................................................................................…

Text truncated - open the document above for the full version.