2A64B-ZJ2618Floor Cleaning Robot

平面印刷品基本技术要求 科沃斯机器人股份有限公司 物料名称普朗克 S Plus- 高配水箱版 - 完整版英文说明书尺 寸145*210mm 型 号ZJ2570印刷颜色单色 K 物料编码xxx-xxxx-xxxx装订方式骑马订 版 次A阶 段A 材 质80g 双胶纸页 数16p 变更记录： 设计审核批准 ECOVACS：机密图档 PLD 2026.05.22 李雯 Instruction Manual 2EN 1. Do not allow to be used as a toy. Close attention is necessary when used by or near children. 2. Clear the area to be cleaned. Remove power cords and small objects from the floor that could entangle the Appliance. Tuck rug fringe under the rug base, and lift items such as curtains and tablecloths off the floor. 3. If there is a drop off in the cleaning area due to a step or stairs, you should operate the Appliance to ensure that it can detect the step without falling over the edge. It may become necessary to place a physical barrier at the edge to keep the unit from falling. Make sure the physical barrier is not a trip hazard. 4. Only use as described in this manual. Only use attachments recommended or sold by the manufacturer. 5. Do not handle plug or appliance with wet hands. 6. Non-rechargeable batteries are prohibited. 7. Do not use without Dust Bin and/or Filters in place. 8. Do not operate the vacuum in an area where there are lit candles or fragile objects on the floor to be cleaned. 9. Do not use and store in extremely hot or cold environments (below -5 ̊C /23 ̊F or above 40 ̊C/104 ̊F). Please charge the robot in temperature above 0°C/32°F and below 40°C/104°F. 10. Keep hair, loose clothing, fingers, and all parts of body away from any openings and moving parts. 11. Do not operate the Appliance in a room where an infant or child is sleeping. 12. For INDOOR use ONLY. Do not use the Appliance in outdoor, commercial or industrial environments. Do not use Appliance on wet surfaces or surfaces with standing water. 13. Do not allow the Appliance to pick up large objects like stones, large pieces of paper, or any item that may clog the Appliance. 14. Do not use to pick up flammable or combustible IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. When using an electrical appliance, basic precautions should always be followed, including the following: WARNING: Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire, or serious injury. 3EN materials such as gasoline, printer, or copier toner, or use in areas where they may be present. 15. Do not pick up anything that is burning or smoking, such as cigarettes, matches, hot ashes, or anything that could cause a fire. 16. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow. 17. Take care not to damage the power cord. Do not pull on or carry the Appliance or Docking Station by the power cord, use the power cord as a handle, close a door on the power cord, or pull power cord around sharp edges or corners. Do not run Appliance and Docking Station over the power cord. Keep power cord away from hot surfaces. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. 18. If the power cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard. 19. Do not use with a damaged power cord or plug. Do not use the Appliance or Docking Station if it is not working properly, has been dropped, damaged, left outdoors, or come in contact with water. It must be repaired by the manufacturer or its service agent in order to avoid a hazard. 20. Turn OFF the power switch before cleaning or maintaining the Appliance. Turn off all controls before unplugging. Always turn off this appliance before connecting or disconnecting motorized nozzle. 21. Turn OFF the Power Switch before removing the Dust Bin. 22. Remove the Appliance from the Docking Station, and turn OFF the power switch to the Appliance before removing the battery for disposal of the Appliance. 23. The battery must be removed and discarded according to local laws and regulations before disposal of the Appliance. 24. Please dispose of used batteries according to local laws and regulations. 25. Do not incinerate the Appliance even if it is severely damaged. The batteries can explode in a fire. 26. When not using the Docking Station, unplug from outlet when not in use and before servicing. 27. The Appliance must be used in accordance with the directions in this Instruction Manual.Ecovacs Home Service Robotics cannot be held liable or responsible for any damages or injuries caused by improper use. 4EN 28. Prevent unintentional starting. Ensure the switch is in the off position before connecting to battery pack, picking up or carrying the appliance. 29. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 30. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns. 31. Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury. 32. Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion. The temperature of 130°C can be replaced by the temperature of 265°F. 33. Follow all charging instructions and do not charge the battery pack or appliance outside of the temperature range specified in the instructions. Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire. 34. Have servicing performed by a qualified repair person using only identical replacement parts. Thi…

Text truncated - open the document above for the full version.

Ecovacs Home Service Robotics Co., Ltd. No.518 Songwei Road,Wusongjiang industry Park, Guoxiang Street, Wuzhong District, Suzhou, Jiangsu, China. 092723-17 rev 10 Certification Application Attestation Statements Date: July 9, 2026 American Certification Body, Inc. 313 Park Avenue Suite 300 Falls Church, VA 22046 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) Ecovacs Home Service Robotics Co., Ltd. certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: <N/A> Statement for 47 CFR section 2.911(d)(5)(ii) Ecovacs Home Service Robotics Co., Ltd. (“the applicant”) certifies that, as of the date of the filing of this application, the applicant ☐ - is / - is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates – see KDB 986446 Question 5) as an entity producing “covered” equipment. The applicant also certifies that the device does not have cybersecurity and/or anti-virus software produced by Kaspersky Lab, Inc or any of its successors and assignees identified on the covered list installed on the device, nor will it be installed by the applicant ay time after certification. Thank you, By: Alix Liu (Signature 2 ) (Print name) Title: Compliance Manager Company: Ecovacs Home Service Robotics Co., Ltd. Telephone: 0512-67072006 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters should be placed on appropriate letterhead.

U.S. Agent Designation for Service of Process (Applicant and U.S. Agent are Separate Parties) TO: American Certification Body, Inc. 313 Park Avenue Suite 300 ATTENTION: FCC Certification – Section 2.911(d)(7) Information Designated U.S. Agent Company Name: Ecovacs Robotics, Inc. FRN: 0033541814 Contact Name: Thomas Climer Street Address: 1500 Fashion Island Blvd., Suite 201 City/Province/Zip: San Mateo, CA 94404 Telephone No: 650.437.2872 Email: [email protected] Signed by (Printed Name/Title): Thomas Climer, GTM Director The Applicant acknowledges that they must maintain an agent for no less than one year after terminating all marketing and importation OR the conclusion of any Commission- related proceeding involving the equipment. The applicant further acknowledges their responsibility to inform the FCC whenever the Designated U.S. Agent information above changes. Applicant Company name: Ecovacs Home Service Robotics Co., Ltd. Grantee Code: 2A64B FRN #: 0032456899 Contact Name: Alix Liu Street Address: No.518 Songwei Road, Wusongjiang industry Park,Guoxiang Street, Wuzhong District City/Province/Zip: Suzhou, Jiangsu,China Telephone No: 0512-67072006 Email: [email protected] Applicant Signature 1 : Signed by (Printed Name/Title): Alix Liu/ Comoliance manager 1 - Letters must be placed on appropriate letterhead. The signee for the applicant must be one of the following: Applicant (grantee) contact of record in the FCC’s authorization system, or authorized officers or employee of the applicant (grantee). Falls Church, VA 22046 Date:10/7/2026 Date: 10/7/2026

Ecovacs Home Service Robotics Co., Ltd. No.518 Songwei Road, Wusongjiang industry Park, Guoxiang Street, Wuzhong District, Suzhou, Jiangsu, China. Declaration Letter We Ecovacs Home Service Robotics Co., Ltd. hereby declare that the product Floor Cleaning Robot / ZJ2618 is not capable of operating with channel 12 and 13 in regions of US and Canada. Versions of the product available for import and sale in the US and Canada will not operate on channels 12 and 13. It will not be possible for users and configure these channels in the US and Canada version. By: ______________________ Alix Liu (Signature 1 ) (Print name) Title: Compliance Manager________ On behalf of: Ecovacs Home Service Robotics Co., Ltd.________ (Company Name) Telephone: _____0512-67072006_____________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Ecovacs Home Service Robotics Co., Ltd. No.518 Songwei Road,Wusongjiang industry Park,Guoxiang Street, Wuzhong District,Suzhou, Jiangsu,China. 041521-14 Authority to Act as Agent Date: July 10, 2026 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: __Intertek Testing Services (Shanghai FTZ) Co., Ltd _ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) with regard to certified equipment. Thank you, Agency Agreement Expiration Date: _____2027.7.10____ By: __________________________ _______Alix Liu________ (Signature 1 ) (Print name) Title: ____Compliance Manager_____ On behalf of: __ Ecovacs Home Service Robotics Co., Ltd.__ (Company Name) Telephone: ____0512-67072006 __________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

Ecovacs Home Service Robotics Co., Ltd. No.518 Songwei Road,Wusongjiang industry Park, Guoxiang Street, Wuzhong District, Suzhou, Jiangsu, China. 041521-14 Request for Confidentiality Date: July 10, 2026 Subject: Confidentiality Request for: ______FCC ID: 2A64B-ZJ2618____ Pursuant to FCC 47 CFR 0.457(d) and 0.459, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit ☐ Short Term ☒ Permanent Block Diagrams ☐ Short Term External Photos ☐ Short Term ☐ Permanent * 1 Internal Photos ☐ Short Term ☒ Permanent Operation Description/Theory of Operation ☐ Short Term ☒ Permanent Schematics ☐ Short Term Test Setup Photos ☐ Short Term ☐ Permanent * 3 User’s Manual __ Ecovacs Home Service Robotics Co., Ltd.____ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180) 2 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By: __________________________ ________Alix Liu_____________ (Signature/Title 3 ) (Print name) 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests. 2 - Please refer to https://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 3 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 External Photos FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618

451-2570-0901 ZJ2618 普朗克S PLUS 尘袋水箱高配 美国主机铭牌(卷装)-试产 注： 1.单位：mm 2.流水号与年周号以物控下单为准！ 3.颜色以封样件为准！ 4.文字字体\排版以电子档确认为准！ 科沃斯机器人股份有限公司 第一视角 设计 标记处数分区变更单号材料见技术要求 物料名称 型 号 物料编码 见技术要求 1:1 质量 比例 版次 阶段 第1页 共1页 审核批准 版次变更内容日期 尺寸展开区 位置示意图 1.尺寸公差：±0.5mm； 2.印刷套印清晰，内容准确、文字不缺笔断画、细微部无明显虚迹； 3.版面整洁，印张空白部分无油腻、墨污、墨杠、手形等污迹； 4.背面清洁无粘脏污迹； 5.无明显的划伤、翘曲、污垢； 6.无模切后的残留渣； 7.物料平整、无异物突出感觉、无卷曲现象； 8.70度高温下168小时不起翘、不脱落、不起泡； 9.通过酒精测试后不起翘、不脱落、不起泡； 表面处理 铭牌标贴基本技术要求 一、材质、工艺 二、质量要求 三、环保要求 零部件环保要求符合ECOVACS《特定有害物质限制标准》 印刷颜色 材 质 四、存储条件 适宜温度：0°C-40°C 适宜湿度：50-60%RH A S 哑膜 单色印刷 背胶 型号 网纹背胶 GT69-142/雅得#9D4/金利宝HTYL75(EB)-C5 是否局部去胶粘贴表面 ABS否 75#压花马拉纸 长(mm) 宽(mm) 100 31 2-2.52-2.5 卷装底纸留白宽度为2.0mm—2.5mm 备注：品质QE反馈工厂打印机设备要求 100mm 31mm R=3mm DEEBOT XXXXXXXXXX 5025506 二维码尺寸：10*10mm 二维码内容-SN规则： XXXXXXXXXXXX00000000 20位 ，同ID ，同二维码 第1位 （黄色 ）：供应商代号（统一用M代替） 第2-12 （绿色 ）：物料ID ，十一位 第12-20 （蓝色 ）：统一八个零代替 备注： 二维码印刷需清晰可识别。 用途： 仅厂内绑定追溯用。 Conforms to UL Std. 1017 Certied to CSA Std. C22.2 NO. 243 生产日期按照实际订单要求由 工厂自行打印 ， 格式MM(月份)/YYYY（年份 ），比如12/2025 MADE IN CHINA/FAIT EN CHINE/HECHO EN CHINA Floor Cleaning Robot/Robot-nettoyeur de plancher/Robot limpia pisos Model/Modèle/Modelo: ZJ2618 Rated Input/Entrée nominale/Entrada clasicada: 17.8V 2A Fast Charge Input/Entrée de charge rapide/Entrada de carga rápida: 16.4V 10.5A Docking Station/Station d'accueil/Estación de carga: CH2586. For use only with Ecovacs Home Service Robotics Co., Ltd. CH2586 charger./ À utiliser uniquement avec le chargeur Ecovacs Home Service Robotics Co., Ltd. CH2586./ Solo para uso con los cargadores CH2586 de Ecovacs Home Service Robotics Co., Ltd. This Device Complies with DHHS Radiation Rules, 21 CFR Chapter 1,Subchapter J./ Cet appareil est conforme aux règles de radiation du DHHS,21 CFR chapitre 1, sous-chapitre J.This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES (B)/NMB (B) FCC ID: 2A64B-ZJ2618 IC: 25893-ZJ2618

FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Internal Photos FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Antenna FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618

Ecovacs Home Service Robotics Co., Ltd. MPE ASSESSMENT REPORT Report Type: FCC Part §2.1091 and §1.1307(b) assessment report Model: ZJ2618 REPORT NUMBER: 2605B1796SHA-003 ISSUE DATE: July 9, 2026 DOCUMENT CONTROL NUMBER: TTRFFCCMPE-01_V1 © 2018 Intertek Intertek Testing Services (Shanghai FTZ) Co., Ltd. Building No.86, 1198 Qinzhou Road (North) Caohejing Development Zone Shanghai 200233, China Telephone: 86 21 6127 8200 www.intertek.com TEST REPORT This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. TTRFFCCMPE-01_V1© 2018 Intertek Page 2 of 8 Report no.: 2605B1796SHA-003 Applicant: Ecovacs Home Service Robotics Co., Ltd. No.518 Songwei Road,Wusongjiang industry Park, Guoxiang Street, Wuzhong District, Suzhou, Jiangsu, China. Manufacturer: Same as applicant Factory 1: Ecovacs Home Service Robotics Co., Ltd. No.518 Songwei Road, Wusongjiang industry Park, Guoxiang Street, Wuzhong District, Suzhou, Jiangsu, China. Factory 2: Competition Team Technology (Vietnam) Co.Ltd. Lot CN-05, Dong Mai Industrial Zone, Dong Mai ward, Quang Ninh province, Vietnam FCC ID: 2A64B-ZJ2618 SUMMARY: The equipment complies with the requirements according to the following standard(s) or Specification: KDB447498 D01 General RF Exposure Guidance v06 FCC Part2.1091, FCC Part1.1307(b) PREPARED BY: REVIEWED BY: Project Engineer Eric Li Reviewer Wakeyou Wang Report No.: 2605B1796SHA-003 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 3 of 8 Revision History Report No. Version Description Issued Date 2605B1796SHA-003 Rev. 01 Initial issue of report July 9, 2026 Report No.: 2605B1796SHA-003 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 4 of 8 1 GENERAL INFORMATION 1.1 Description of Equipment Under Test (EUT) Product name: Floor Cleaning Robot Type/Model/PMN/HVIN: ZJ2618 Description of EUT: EUT is a Floor Cleaning Robot which supports Bluetooth and WIFI functions. We tested it and listed the worst results in this report. Rating: Rated Input: DC17.8V, 2A Fast Charge Input: DC16.4V, 10.5A Brand Name: , , , Category of EUT: Class B EUT type: Table top Floor standing Software Version: / Hardware Version: / Sample Identification No.: A260616-002-001 Sample received date: 2026.6.16 Date of test: 2026.6.16~2026.6.29 1.2 Technical Specification Frequency Band: 2402MHz to 2480MHz Support Standards: Bluetooth Low Energy Type of Modulation: GFSK Channel Number: 40 Data Rate 1Mbps Channel Separation: 2MHz Antenna Information: FPC Antenna, gain is 0.80dBi Frequency Band: 2400MHz ~ 2483.5MHz Support Standards: IEEE 802.11b, IEEE 802.11g, IEEE 802.11n-HT20, IEEE 802.11n-HT40 Type of Modulation: IEEE 802.11b: DSSS (CCK, DQPSK, DBPSK) IEEE 802.11g: OFDM (64-QAM, 16-QAM, QPSK, BPSK) IEEE 802.11n-HT20: OFDM (64-QAM, 16-QAM, QPSK, BPSK) IEEE 802.11n-HT40: OFDM (64-QAM, 16-QAM, QPSK, BPSK) Channel Number: 11 Channels for 802.11b, 802.11g, 802.11n(HT20) 7 Channels for 802.11n(HT40) Channel Separation: 5 MHz Antenna: FPC Antenna, gain is 0.80dBi Report No.: 2605B1796SHA-003 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 5 of 8 1.3 Description of Test Facility Name: Intertek Testing Services (Shanghai FTZ) Co., Ltd. Address: Building 86, No. 1198 Qinzhou Road(North), Shanghai 200233, P.R. China Telephone: 86 21 61278200 Telefax: 86 21 54262353 The test facility is recognized, certified, or accredited by these organizations: CNAS Accreditation Lab Registration No. CNAS L21189 FCC Accredited Lab Designation Number: CN0175 IC Registration Lab CAB identifier.: CN0014 VCCI Registration Lab Member No: 3598 (Registration No.: R-14243, G-10845, C-14723, T-12252) A2LA Accreditation Lab Certificate Number: 3309.02 Report No.: 2605B1796SHA-003 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 6 of 8 2 MPE Assessment Test result: Pass 2.1 MPE Assessment Limit Mobile device exposure for standalone operations: Frequency range E-field strength (V/m) H-field strength (A/m) B-field (uT) Equivalent plane wave power density S eq (W/m 2 ) 0-1 Hz - 3,2 × 10 4 4 × 10 4 - 1-8 Hz 10 000 3,2 × 10 4 /f 2 4 × 10 4 /f 2 - 8-25 Hz 10 000 4 000/f 5 000/f - 0,025-0,8 kHz 250/f 4/f 5/f - 0,8-3 kHz 250/f 5 6,25 - 3-150 kHz 87 5 6,25 - 0,15-1 MHz 87 0,73/f 0,92/f - 1-10 MHz 87/f 1/2 0,73/f 0,92/f - 10-400 MHz 28 0,073 0,092 2 400-2 000 MHz 1,375 f 1/2 0,0037 f 1/2 0,0046 f 1/2 f/200 2-300 GHz 61 0,16 0,20 10 Mobile device exposure for simultaneous transmission operations: the sum of the MPE ratios for all simultaneously transmitting antennas incorporated in a host device is ≤ 1.0 Report No.: 2605B1796SHA-003 TEST REPORT TTRFFCCMPE-01_V1© 2018 Intertek Page 7 of 8 2.2 Assessment Results Power density (S) is calculated according to the formula: S = PG / (4πR²) Where S = power density in mW/cm² P = Radiated transmit power in mW G = numeric gain of transmit antenna R = distance (cm) As we can see from the test report 2605B1796SHA-001 and 2605B1796SHA-002: The calculations in the table below use the highest gain of antenna for client EUT. These calculations represent worst case in terms of the exposure levels. Mode Frequency band Max Power Antenna Gain R S Limits (MHz) dBm dBi (cm) (mW/cm2) (mW/cm2) Bluetooth 2402-2480 4.39 0.80 20 0.000…

Text truncated - open the document above for the full version.

供应商名称：欧智通科技股份有限公司 Supplier Name: Ouzhitong Technology Co., Ltd 供应商地址：深圳市宝安区西乡街道共乐社区铁仔路50号凤凰智谷B座14层 Supplier Address: 14th Floor, Block B, Fenghuang Zhigu, No. 50 Tiezi Road, Gongle Community, Xixiang Street, Bao'an District, Shenzhen 供应商工厂:湖南省长沙市浏阳经济开发区利通路8号 Supplier Factory: No. 8 Litong Road, Liuyang Economic Development Zone, Changsha City, Hunan Province 供应商电话：86-755-2955-8186 Supplier's phone number: 86-755-2955-8186 供应商网址:www.fn-link.com Supplier website: www.fn link.com 承认书 欧智通科技股份有限公司 FN-LINK TECHNOLOGY Ltd. FN-LINK TECHNOLOGY LIMITED CUSTOMER APPROVEDBY 批准Approved by审核Checked by制表Preparedby SUPPLIER APPROVEDBY 批准Approved by审核Checked by制表Preparedby Customer Project Name 哥白尼-蓝 Customer NO. specification 2400-2500MHz Supplier NO. Specification NO. Write by REV. Ver.1 Date 2025-04-10 Note 天线测试报告 antenna testing FN-LINK TECHNOLOGY LIMITED Change contentversion Change person Approve d by 2024.04.10 首版发行 V1.0 FN-LINK TECHNOLOGY LIMITED 序号 Number 内容 content 页码 Page number - 承认书封面 Acknowledgment Letter Cover 1 one - 天线测试报告 Antenna test report 2 two - 版本变更记录 Version change record 3 three 1 one 承认书项目表 Confirmation Letter Project Table 4 four 2 two 试验设备和条件 Test equipment and conditions 5 five 3 three 样机结构说明件 Prototype structure specification 6 six 4 four 天线成品图 Finished antenna diagram 7 seven 5 five 有源数据/S11驻波图 8 eight 6 six 增益/效率/3D图 Gain/Efficiency/3D Graph 9 nine- fourteen 7 seven 包装 packing 10 fifteen 1. 承认书项目表(Index) 1. Recognition Letter Project Table (Index) FN-LINK TECHNOLOGY LIMITED 2. 试验设备和条件(Test Equipment & Conditions) 1.1NetworkAnalyzers: KEYSIGHTP5002A1.2Communications TestSet:R&SCMW500 1.33DChamberTestSystem: 24探头测试系统（24 probe testing system） 1.微波暗室的测试原理图（Testing principle diagram of microwave anechoic chamber 2.说明。 这份报告总结了该项目天线的电气性能结果，包括天线的S11 参数,Gain和Efficiency.2. Explanation. This report summarizes the electrical performance results of the antenna for the project, including the S11 parameters, Gain, and Efficiency of the antenna FN-LINK TECHNOLOGY LIMITED 4.天线成品图 Finished antenna diagram FN-LINK TECHNOLOGY LIMITED FN-LINK TECHNOLOGY LIMITED 5. S11Main antennaS11 天线驻波图： FN-LINK TECHNOLOGY LIMITED 6.增益/效率/3D图 Gain/Efficiency/3D Graph Frequency/MhzEfficiency / %MaxGain/dBi 240036.06-1.45 241041.4-0.44 242044.670.11 243049.320.8 244047.970.52 245043.350.05 246040.27-0.37 247036.81-0.68 248033.65-1.23 249034.36-1.2 250032.73-1.45 FN-LINK TECHNOLOGY LIMITED 7.包装 packing 产品包装规范Code for product packaging

FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Appendix A of 2605B1796SHA-001 Test Data of Bluetooth DTS Bandwidth Test Result TestMode Antenna Frequency [MHz] DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict BLE_1M Ant1 2402 0.712 2401.652 2402.364 0.5 PASS BLE_1M Ant1 2440 0.728 2439.644 2440.372 0.5 PASS BLE_1M Ant1 2480 0.716 2479.656 2480.372 0.5 PASS FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Test Graphs BLE_1M-Ant1-2402-PASS BLE_1M-Ant1-2440-PASS BLE_1M-Ant1-2480-PASS FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Occupied Channel Bandwidth Test Result TestMode Antenna Frequency [MHz] OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict BLE_1M Ant1 2402 1.0361 2401.5061 2402.5422 --- --- BLE_1M Ant1 2440 1.0361 2439.5067 2440.5428 --- --- BLE_1M Ant1 2480 1.0350 2479.5076 2480.5426 --- --- FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Test Graphs BLE_1M-Ant1-2402 BLE_1M-Ant1-2440 BLE_1M-Ant1-2480 FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Maximum conducted output power Test Result Peak TestMode Antenna Frequency [MHz] Conducted Peak Powert[dBm] Conducted Limit[dBm] EIRP[dBm] EIRP Limit[dBm] Verdict BLE_1M Ant1 2402 3.74 ≤30 4.54 ≤36 PASS BLE_1M Ant1 2440 3.94 ≤30 4.74 ≤36 PASS BLE_1M Ant1 2480 4.39 ≤30 5.19 ≤36 PASS FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Test Graphs Peak BLE_1M-Ant1-2402-PASS BLE_1M-Ant1-2440-PASS BLE_1M-Ant1-2480-PASS FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Maximum power spectral density Test Result TestMode Antenna Frequency [MHz] Result[dBm/3kHz] Limit[dBm/3kHz] Verdict BLE_1M Ant1 2402 -11.57 ≤8.00 PASS BLE_1M Ant1 2440 -11.48 ≤8.00 PASS BLE_1M Ant1 2480 -10.80 ≤8.00 PASS FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Test Graphs BLE_1M-Ant1-2402-PASS BLE_1M-Ant1-2440-PASS BLE_1M-Ant1-2480-PASS FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Band edge measurements Test Result TestMode Antenna ChName Frequency [MHz] RefLevel[dBm] Result[dBm] Limit[dBm] Verdict BLE_1M Ant1 Low 2402 2.76 -48.32 ≤-17.25 PASS BLE_1M Ant1 High 2480 3.57 -47.84 ≤-16.43 PASS FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Test Graphs BLE_1M-Ant1-2402-PASS BLE_1M-Ant1-2480-PASS FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Conducted Spurious Emission Test Result TestMode Antenna Frequency [MHz] FreqRange [MHz] RefLevel [dBm] Result[dBm] Limit[dBm] Verdict BLE_1M Ant1 2402 0~Reference 3.00 3.00 --- PASS BLE_1M Ant1 2402 30~1000 3.00 -60.3 ≤-17 PASS BLE_1M Ant1 2402 1000~26500 3.00 -38.4 ≤-17 PASS BLE_1M Ant1 2440 0~Reference 3.03 3.03 --- PASS BLE_1M Ant1 2440 30~1000 3.03 -62.35 ≤-16.97 PASS BLE_1M Ant1 2440 1000~26500 3.03 -38.37 ≤-16.97 PASS BLE_1M Ant1 2480 0~Reference 3.65 3.65 --- PASS BLE_1M Ant1 2480 30~1000 3.65 -62.3 ≤-16.35 PASS BLE_1M Ant1 2480 1000~26500 3.65 -38.88 ≤-16.35 PASS FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Test Graphs BLE_1M-Ant1-2402-0~Reference-PASS BLE_1M-Ant1-2402-30~1000-PASS BLE_1M-Ant1-2402-1000~26500-PASS FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 BLE_1M-Ant1-2440-0~Reference-PASS BLE_1M-Ant1-2440-30~1000-PASS BLE_1M-Ant1-2440-1000~26500-PASS FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 BLE_1M-Ant1-2480-0~Reference-PASS BLE_1M-Ant1-2480-30~1000-PASS BLE_1M-Ant1-2480-1000~26500-PASS

FCC ID: 2A64B-ZJ2618 IC: 28593-ZJ2618 Appendix B of 2605B1796SHA-002 Test Data of WIFI DTS Bandwidth Test Result TestMode Antenna Frequency[MHz] DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11B Ant1 2412 9.040 2407.000 2416.040 0.5 PASS 11B Ant1 2437 8.600 2432.480 2441.080 0.5 PASS 11B Ant1 2462 8.600 2457.960 2466.560 0.5 PASS 11G Ant1 2412 16.320 2403.840 2420.160 0.5 PASS 11G Ant1 2437 16.280 2428.880 2445.160 0.5 PASS 11G Ant1 2462 16.320 2453.840 2470.160 0.5 PASS 11N20SISO Ant1 2412 17.240 2403.520 2420.760 0.5 PASS 11N20SIS…

Text truncated - open the document above for the full version.