2AA2X-15000301Network Hub

VERSA EX™ PRODUCT MANUAL 1 MTI P/N 063-00393 rev A ©2021 MTI All Rights Reservedwww.mtigs.com | T:800.426.6844 Product Manual for Compatible with Freedom Micro® II, CX Flex™ 4A/1P+, MTI Locks™, and Freedom Focus™ Versa EX™ Network Hub DO NOT REMOVE FROM STORE Contents 1.Materials in Box2 2.Installation2 3.Key Whitelist3 4.Merchandising3 5.Managing Alarms4 6.Cable Removal4 7.Remerchandising4 8.Adding New User Keys5 9.Deleting Whitelist5 10.LED Status Indicators6 11.Dimensions7 12.FCC and ISED Statement8 For additional support, please reach out to our Contact Center at 800-426-6844 CONTENTS 1 2 Versa EX™ Versa Key™ Network Pairing Card Versa Key™ Authorization Card USB-C Female End USB-C Male End Power Supply 3 Use only power supply with output ratings 5VDC 3A max, of PS2 or LPS. The socket-outlet shall be installed near the equipment and shall be easily accessible. Utilisez uniquement une alimentation avec des valeurs de sortie de 5VCC 3A Max, de PS2 ou LPS. La prise de courant doit être installée à proximité de l'équi- pement et doit être facilement accessible VERSA EX™ PRODUCT MANUAL 2 MTI P/N 063-00393 rev A ©2021 MTI All Rights Reservedwww.mtigs.com | T:800.426.6844 INSTALLATION MATERIALS IN BOX Feed power cable through hole in fixture (if needed), and press down on the base plate for 10 seconds for full VHB contact. Allow 24 hours for full VHB adhesion. Clean the desired surface with an alcohol pad allow it to completely dry. Peel the red film from the VHB adhesive. Use the individual power supply and plug it into the nearest outlet. Use an outlet installed near the equipment that is easily accessible. NETWORK PAIRING AUTHORIZATION 1 1 32 Place Pairing Card over the RFID icon to place Versa EX in pairing mode. LED will be flashing blue. Position connects successfully to mesh network: Position fails to connect to mesh network within 3 minutes: VERSA KE Y ™ NETWORK PAIRING Slow Beeps Double Beep Four Fast Reject Beeps VERSA EX™ PRODUCT MANUAL 3 MTI P/N 063-00393 rev A ©2021 MTI All Rights Reservedwww.mtigs.com | T:800.426.6844 PAIRING VERSA EX ENTER NETWORK MODE FOR FREEDOM MICRO II KEY WHITELIST Place Authorization Card over the RFID icon to register to system. LED will be solid blue. System must be disarmed to perform this operation. Place the User Key over the RFID icon you want to add. If successful  unit beeps 2 times If unsuccessful  unit beeps 4 times (retry) Repeat process for all User Keys until they are successfully added. To close the whitelist mode, place the Authorization Card over the RFID icon. Whitelist mode will end automatically after 3 minutes of no use. LED will double flash yellow every 8 seconds on initial setup, indicating no positions are paired to Versa EX. 1 1 ENTER NETWORK MODE FOR MTI LOCKS Swipe Network Pairing card to enter enrollment mode. You will hear slow beep tones indicating it is in pairing mode. A double beep at the end indicates successful pairing. 2 From an armed state, place the user key over the RFID icon to disarm the system. LED will be flashing white. 1 VERSA EX™ PRODUCT MANUAL 4 MTI P/N 063-00393 rev A ©2021 MTI All Rights Reservedwww.mtigs.com | T:800.426.6844 To silence an alarm, tap the user card over the RFID icon. Will silence alarm on position that is alarming. All other positions will remain armed. To disarm all, tap Versa key again. To clear alarm condition from position, check all triggers and re-arm the whole position. MANAGING ALARMS 1 MICRO II LOCKDOWN MODE ACTIVATION Tap and hold Versa Key onto Versa EX for 10 seconds. Position will double beep immediately, and then again when lockdown mode has been activated. Repeat step to toggle back to unlocked mode. ADDING NEW USER KEYS Place Authorization Card over the RFID icon. Follow Key Whitelist process starting on page 3. 5 MTI P/N 063-00393 rev A ©2021 MTI All Rights Reservedwww.mtigs.com | T:800.426.6844 1 3 2 4 132 DELETING WHITELIST (This will delete all User Keys from the system.) REMOVE INDIVIDUAL KEYS FROM WHITELIST Hold down the Authorization Card for 10 seconds, LED will be solid blue. From an Armed state, place the User Key over the RFID icon to disarm the system. LED will be flashing white. From an Armed state, place the User Key over the RFID icon to disarm the system. LED will be flashing white. Hold down User Key to be removed for 10 seconds. Key will double beep immediately and then double beep confirming successful removal of key. Place Authorization Card over the RFID icon to enter programming mode. LED will be solid blue. Place Authorization card over the RIFD icon to exit programming mode, or it will time out automatically after 3 minutes. Place the Authorization Card over the RFID icon AGAIN while LED is blue. If successful  unit beeps 2 times and LED double flashes white every 8 seconds If unsuccessful  unit beeps 4 times (retry) VERSA EX™ PRODUCT MANUAL 6 MTI P/N 063-00393 rev A ©2021 MTI All Rights Reservedwww.mtigs.com | T:800.426.6844 LED STATUS INDICATORS Visual ReferenceSystem StatusConditionSolution LED is solid white.ArmedSystem is armed. LED is flashing white.DisarmedSystem is disarmed and is ready to merchandise or re-arm. LED is flashing red and white.AlarmSystem is alarming and requires immediate attention. LED is flashing green.Factory Reset System has no whitelist or Authorization Card. Follow key whitelist process. LED is solid green.Ready to Whitelist System has an Authorization Card, but does not have any User Keys added. Follow key whitelist process. LED is solid blue. 1. Whitelist Mode (if using Authorization Card) 2. Overcurrent when armed 1. System is in whitelist enrollment mode. Follow whitelist process to add User Keys. 2. System has gone into overcurrent protection. Unplug any product which may be drawing too much power. LED is flashing blue. 1. Connect Provisioning Mode 2. Overcurrent when disarmed 1. In Connect Provisioning Mode; LEDs return to previous Color when Provisioning is complete or times-out after ~1.5 minutes. 2. System …

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICE Report No.: HK21061501 Equipment Photographs (External)

size 3 inch X 1 inch

INTERTEK TESTING SERVICE Report No.: HK21061501 Equipment Photographs (Internal) INTERTEK TESTING SERVICE Report No.: HK21061501 Equipment Photographs (Internal) INTERTEK TESTING SERVICE Report No.: HK21061501 Equipment Photographs (Internal)

Analysis Report Report No.: 21061501HKG-001 The Equipment Under Test (EUT) is Versa Ex. The EUT has 125kHz RFID reader and 2.4GHz Zigbee transceiver for wireless connectivity. 2.4GHz Zigbee portion Antenna Type: Internal, Integral Antenna Gain: -1 dBi Peak Conducted output power: 4 dBm Frequency range: 2405MHz to 2480MHz, channel spacing 5MHz (16 channels) 125kHz RFID portion Antenna Type: Internal, Integral Antenna Gain: 0dBi Maximum Field Strength: 73 dBμV/m@3m Frequency range: 125kHz (single channel) According to the KDB 447498: 2.4GHz Zigbee portion Conducted Power (max) = 4 dBm (2.51 mW) The SAR Exclusion Threshold Level: = 3.0 * (min. test separation distance, mm) / sqrt(freq. in GHz) = 3.0 * 5 / sqrt (2.480) mW = 9.53 mW Since the above conducted output power is well below the SAR Exclusion threshold level, so the EUT is considered to comply with SAR requirement without testing. 125kHz RFID reader portion Based on the Maximum allowed field strength of production tolerance was 73 dBμV/m at 3m in frequency 125kHz, thus; The EIRP = [(FS*D) ^2*1000 / 30] = 0.006 mW (-22.2 dBm) Conducted power = Radiated Power (EIRP) – Antenna Gain = (-22.2 dBm – 0 dBi) So; Conducted Power = 0.006 mW (-22.2 dBm). The SAR Exclusion Threshold Level for 125kHz when the minimum test separation distance is < 50mm: = [948 * (1 + log100/f(MHz))]/2 = 1850 mW Since the above conducted output power is well below the SAR Exclusion threshold level, so the EUT is considered to comply with SAR requirement without testing. Simultaneous Transmission SAR exclusion considerations Since the 2.4GHz Zigbee transceiver and 125kHz RFID reader of this device may operate simultaneously, simultaneous transmission analysis is required. Per KDB 447498, simultaneous transmission SAR test exclusion can be applied when the sum of 1-g SAR of all simultaneously transmitting antennas in an operating mode and exposure condition combination is within the SAR limit ( ≤ 1.6W/kg). When the standalone SAR test exclusion is applied, the standalone 1-g SAR must be estimated according to the following equation, Estimated SAR = )max/()5.7/)((TDPxGHzF where F(GHz) is the RF channel transmit frequency in GHz Pmax is the max. power of channel, including tune-up tolerance, mW TD is the min. test separation distance, mm For 2.4GHz Zigbee operation, Maximum Time-averaged Conducted Power of this device = 2.51 mW Therefore, the Estimated SAR will be determined as follow, Estimated SAR = )max/()5.7/)((TDPxGHzF = 0.1054 W/kg where Pmax = 2.51 mW, TD = 5 mm and F(GHz) = 2.480 GHz For 125kHz RFID reader operation, Maximum Time-averaged Conducted Power of this device = 0.006 mW Therefore, the Estimated SAR will be determined as follow, Estimated SAR = )max/()5.7/)((TDPxGHzF = 0.000001788 W/kg where Pmax = 0.006 mW, TD = 5 mm and F(GHz) = 0.000125 GHz Simultaneous Transmission Analysis 2.4GHz Zigbee SAR (W/kg) 125kHz RFID reader SAR (W/kg) Σ SAR (W/kg) Simultaneous SAR Required 0.1054 0.000001788 0.105401788 No Conclusion Since the above summed SAR result for all simultaneous transmission conditions were below the SAR limit (1.6 W/kg), SAR evaluation for simultaneous transmission configuration are not required.

2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong SAR, China. Telephone: (852) 2173 8888 Facsimile: (852) 2785 5487 www.intertek.com Intertek’s standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. © 2017 Intertek Page 1 of 38 TEST REPORT Report Number: 21061501HKG-001 Mobile Technologies Inc. Application For Certification (Original Grant) FCC ID: 2AA2X-15000301 IC: 24439-15000301 Transceiver PREPARED AND CHECKED BY: APPROVED BY: Signed On File Wong Cheuk Ho, Herbert Lead Engineer Wong Kwok Yeung, Kenneth Assistant Supervisor Date: 20 Aug 2021 TEST REPORT Mobile Technologies Inc. Intertek Report No: 21061501HKG-001 Page 2 of 38 GENERAL INFORMATION Applicant Name: Mobile Technologies Inc. Applicant Address: Contact Person: e-mail: Brand Name: 1050 NE 67th Ave., Hillsboro, Oregon 97124, United States Audy Tse [email protected] MTI FCC Specification Standard: FCC Part 15, October 1, 2019 Edition FCC ID: 2AA2X-15000301 FCC Model(s): VERSA EX IC Specification Standard: RSS-247 Issue 2, February 2017 RSS-Gen Issue 5 + Amendment 2 (February 2021) IC: 24439-15000301 PMN: VERSA EX HVIN: VERSA EX Type of EUT: Spread Spectrum Transmitter Description of EUT: Network Hub Serial Number: D23MT0100023 Sample Receipt Date: 28 Jun 2021 Date of Test: 10 Jul 2021 to 20 Jul 2021 Report Date: 20 Aug 2021 Environmental Conditions: Conclusion: Temperature: +10 to 40°C Humidity: 10 to 90% Test was conducted by client submitted sample. The submitted sample as received / after modification complied with the 47 CFR Part 15 / RSS-210 Issue 10 Certification. TEST REPORT Mobile Technologies Inc. Intertek Report No: 21061501HKG-001 Page 3 of 38 TABLE OF CONTENTS 1.0 Test Results Summary & Statement of Compliance .................................................................. 4 1.1 Summary of Test Results ........................................................................................................ 4 1.2 Statement of Compliance........................................................................................................ 4 2.0 General Description ................................................................................................................... 5 2.1 Product Description ............................................................................................................... 5 2.2 Test Methodology ................................................................................................................... 6 2.3 Test Facility ............................................................................................................................. 6 2.4 Related Submittal(s) Grants .................................................................................................... 6 3.0 System Test Configuration ......................................................................................................... 7 3.1 Justification ............................................................................................................................. 7 3.2 EUT Exercising Software .......................................................................................................... 8 3.3 Details of EUT and Description of Accessories ......................................................................... 9 3.4 Measurement Uncertainty ...................................................................................................... 9 4.0 Test Results .............................................................................................................................. 10 4.1 Maximum Conducted Output Power at Antenna Terminals ................................................. 10 4.2 Minimum 6dB RF Bandwidth ................................................................................................ 12 4.3 Maximum Power Spectral Density ........................................................................................ 15 4.3 Maximum Power Spectral Density ........................................................................................ 15 4.4 Out of Band Conducted Emissions ........................................................................................ 18 4.5 Field Strength Calculation ..................................................................................................... 23 4.6 Transmitter Radiated Emissions in Restricted Bands and Spurious Emissions ....................... 24 4.6.1 Radiated Emission Configuration Photograph .................................................................... 24 4.6.2 Radiated Emission Data ...................................................................................................... 24 4.6.3 Radiated Emission Test Setup ............................................................................................ 29 4.6.4 Transmitter Duty Cycle Calculation ................................................…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICE Report No: HK21061501 Configuration Photographs Worst-Case Radiated Emissions (Front View) INTERTEK TESTING SERVICE Report No: HK21061501 Configuration Photographs Worst-Case Radiated Emissions (Rear View)

INTERTEK TESTING SERVICE Report No: HK21061501 Configuration Photographs Worst-Case Radiated Emissions (Front View) INTERTEK TESTING SERVICE Report No: HK21061501 Configuration Photographs Worst-Case Radiated Emissions (Rear View)

INTERTEK TESTING SERVICE Report No: HK21061501 i Configuration Photographs Worst-Case Line-Conducted Emissions (Front View) INTERTEK TESTING SERVICE Report No: HK21061501 ii Configuration Photographs Worst-Case Line-Conducted Emissions (Rear View) INTERTEK TESTING SERVICE Report No: HK21061501 iii Configuration Photographs Worst-Case Line-Conducted Emissions (Side View)