2AA9WV1001WCDMA Digital Mobile Phone

1 Table of Contents 1.Foreword ............................................................. 2 2.Getting to know your touch phone .................. 5 3.Starting up the device ........................................ 6 4.Introduce the basic phone function ................. 8 5.Technical Specifications ................................. 14 6.SAR .................................................. 16 2 Foreword Safety In order to ensure the phone is used safely and correctly, please read the precautions below carefully before use. 1.1 General precaution ·Your phone is only suitable for the battery and charger approved by our company or else it may cause the battery to leak, overheat, explode or even catch fire. ·Do not knock, vibrate or throw the phone heavily to avoid malfunction, fire, overheating, explosion or fire. ·If there are abnormal phenomena, like temperature rising, color change or distortion during the usage, charging or storage of the battery, please stop using it and replace it with a new battery. ·It may burn the skin if liquid in the battery leaks onto skin or clothes. If this happens please flush with plenty of clean water immediately and go to a hospital at once. ·Please keep the battery away from fire to avoid fire and explosion if the battery leaks or emits a strange smell. ·Do not place expose the battery to moisture or it may cause overheating, fumes and corrosion. ·Do not use or place the battery under direct sunlight, or in hot places, it may cause leakage and overheating, thus reducing performance and shortening the lifespan. ·Do not charge the battery for over 24 hours continuously. ·Use careful with the earphone maybe possible excessive sound presure from earphones and headphones can cause hearing loss. 1.2 Precaution for the use of charger ·Do not cause short circuit to the charger, or it may cause electric shock, fumes and damage to the charger. ·Do not use the charger if the power wire is broken, or it may cause fire and electric shock. ·Please remove accumulated dust on the power plug. ·Do not put water containers next to the power supply to avoid overheating, fire, electric shock and malfunction in case they come into contact. ·Do not disassemble or tamper with the charger or it may cause personal injury, electric shock, fire and the damage of the charger. ·Do not use the charger in places of high humidity, like bathrooms, or it may cause electric shock, fire and damage of charger. 3 ·Do not touch the charger, power cord or power plug with wet hands or it can cause electric shock. ·Do not put heavy objects on the power cord or change the power cord or it may cause electric shock and fire. ·Please unplug the power socket before cleaning and maintenance. ·Please hold the charger to unplug the socket as pulling the power cord may damage the power wire and cause electric shock and fire. 1.3 Cleaning and maintenance ·As the phone, battery and charger are not waterproof, do not use them in places of high humidity and avoid them being wet by rain. ·Please clean the battery and charger with a soft dry cloth. ·Never use alcohol, thinner or solutions, like benzene, to wipe the phone. ·Dirty sockets can cause poor contact and power down, and even make recharging unavailable. So, please clean them periodically. 1.4 Common Precaution Mobile Phone: ·Please use the phone in an environment with temperature between -10°C- 55°Cand humidity of ≤80%. ·Please use the phone far away from regular telephones, TV sets, radio sets and office automation equipment, to avoid affecting the normal use of these equipments and mobile phone. Battery: ·Store the battery in cool and ventilated place without direct sunlight. ·The battery has a limited lifespan. The usage of battery will be shortened progressively due to frequent charging. Once the battery is out of use, it means that its lifespan has ended, and you will need to replace it with an approved new battery. ·Do not dispose of old batteries as household waste. Give them to specified disposal places and follow any stipulated instructions for disposal. CAUTION:RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCYIONS. Charger: ·Do not charge under following conditions: -- places with direct sunlight -- places with ambient temperature less than -10°C or over 55°C, 4 wet or dusty places with strong vibrations (it may cause malfunction) -- places near electrical appliances (it may affect the image and sound) like TV set, radio, etc -- Adapter shall be installed near the equipment and shall be easily accessible. The plug considered as disconnect device of adapter. 5 Getting to know your touch phone 6 Starting up the device To remove the back cover ·Make sure your device is turned off. ·Firmly hold the device with the front panel facing down. ·Slide your finger into the groove at the top of the phone and gently pull open the back cover. To install the SIM card ·Remove the battery if it is installed. ·Locate the SIM card slot, and then insert the SIM card with its gold contacts facing down and its cut-off corner facing out of the card slot as shown in the diagram. ·Slide the SIM card completely into the slot. Note: The phone can support two SIM cards. The card will support 2G card and 3G card. To install a memory card To have additional storage for your images, videos, music and files, you can purchase a memory card and install it in your device. Locate the memory card slot on the upper part of the exposed right panel. Insert the memory card into the slot with its gold contacts facing down until it clicks into place To install the battery 1. Align the battery’s exposed copper contacts with the battery connectors at the bottom part of the battery compartment. 2. Insert the contacts side of the battery first and then gently push the battery into place. Replace the back cover. Charging the Battery New batteries are shipped partially charged. Before you start using your device, it is recom…

Text truncated - open the document above for the full version.

022311 – 6 Authority to Act as Agent Date: 2014/6/12________ American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: East China Institute of Telecommunications / Yaqiong Wang is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b), to the application is subject to denial of federal benefits that includes FCC benefits. Thank you, Agency Agreement Expiration Date: ____12 months__ By: __________________________ Amit Verma (Signature 1 ) (Print name) Title: Director of Test Engineering On behalf of: VSN Technologies Inc. d/b/a VSN Mobil _ (Company Name) Telephone: ____954-609-4912________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

THIS MUST BE SIGNED BY THE APPLICANT/AGENT AND SHOULD BE PLACED ON APPROPRIATE LETTERHEAD 022311 – 6 Request for Confidentiality Date: 2014/7/25 Subject: Confidentiality Request for: ____2AA9WV1001_____ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 2 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ ______ VSN Technologies Inc. d/b/a VSN Mobil _____ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180) 3 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: __________________________ _____ _ Amit Verma _____ (Signature/Title 4 ) (Print name) 2 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 3 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 4 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

0089 External Photo Mobile Phone Mobile Phone Mobile Phone Mobile Phone Mobile Phone Mobile Phone Battery Battery USB Cable Earphone 1 Earphone 2 Charger Charger Label

ARTWORK COMPOSITE V.45 IMEI Label 1 SIM MEXICO Artwork-BLACK Pr oduction Graphics VER.3 June 5, 2014 PRINT BLACK ON WHITE LABEL NEED INFO FILLED IN AND BARS CORRECT BEFORE PRINTING 6/4- Revisons to text 6/5 - remove IFT number IMEI:123456789012345 S/N:123456789012345 DIGITAL CELLULAR PHONE MODEL: V.35 MODEL NUMBER: V1001 MANUFACTURER: VSN MOBIL, INC. Made In China ELECTRICAL SPECIFICATIONS: 3.7 VCC FCC ID: 2AA9WV1001 COLOR: BLACK IMEI:123456789012345 S/N:123456789012345 DIGITAL CELLULAR PHONE MODEL: V.35 MODEL NUMBER: V1001 MANUFACTURER: VSN MOBIL, INC. Made In China ELECTRICAL SPECIFICATIONS: 3.7 VCC FCC ID: 2AA9WV1001 COLOR: BLACK

0089 Internal Photo Mobile Phone Mobile Phone Mobile Phone Mobile Phone Mobile Phone Charger Charger

Full TEST REPORT No. 2014SAR0089 For Client : VSN Technologies Inc. d/b/a VSN Mobil Production : WCDMA Digital Mobile Phone Model Name : V.35 / Nextel V.35 Model Number: V1001 FCC ID: 2AA9WV1001 Hardware Version: V01 Software Version: V01 Issued date: 2014-08-16 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of ECIT Shanghai. Test Laboratory: ECIT Shanghai, East China Institute of Telecommunications Add: 7-8F, G Area, No.668, Beijing East Road, Huangpu District, Shanghai, P. R. China Tel: (+86)-021-63843300, E-Mail: [email protected] SAR Test Report Report No.: 2014SAR0089 East China Institute of Telecommunications Page Number : 2 of 205 TEL: +86 21 63843300FAX:+86 21 63843301 Report Issued Date :August 16, 2014 Revision Version Report Number Revision Date Memo 2014SAR0089 00 2014-07-05 Initial creation of test report 2014SAR0089 01 2014-08-08 Second creation of test report 2014SAR0089 02 2014-08-14 Third creation of test report 2014SAR0089 03 2014-08-16 The fourth creation of test report SAR Test Report Report No.: 2014SAR0089 East China Institute of Telecommunications Page Number : 3 of 205 TEL: +86 21 63843300FAX:+86 21 63843301 Report Issued Date :August 16, 2014 CONTENTS 1. TEST LABORATORY ........................................................................................................... 6 1.1. TESTING LOCATION ........................................................................................................... 6 1.2. TESTING ENVIRONMENT ................................................................................................... 6 1.3. PROJECT DATA ................................................................................................................... 6 1.4. SIGNATURE ......................................................................................................................... 6 2. STATEMENT OF COMPLIANCE .......................................................................................... 7 3. CLIENT INFORMATION ....................................................................................................... 9 3.1. APPLICANT INFORMATION ................................................................................................ 9 3.2. MANUFACTURER INFORMATION ...................................................................................... 9 4. EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ........................ 10 4.1. ABOUT EUT ....................................................................................................................... 10 4.2. INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST .................................. 11 4.3. INTERNAL IDENTIFICATION OF AE USED DURING THE TEST ..................................... 11 5. TEST METHODOLOGY ..................................................................................................... 12 5.1. APPLICABLE LIMIT REGULATIONS ................................................................................ 12 5.2. APPLICABLE MEASUREMENT STANDARDS ................................................................. 12 6. SPECIFIC ABSORPTION RATE (SAR) ............................................................................. 14 6.1. INTRODUCTION ................................................................................................................. 14 6.2. SAR DEFINITION ............................................................................................................... 14 7. TISSUE SIMULATING LIQUIDS ......................................................................................... 15 7.1. TARGETS FOR TISSUE SIMULATING LIQUID ................................................................. 15 7.2. DIELECTRIC PERFORMANCE.......................................................................................... 15 8. SYSTEM VERIFICATION ................................................................................................... 19 8.1. SYSTEM SETUP ................................................................................................................ 19 8.2. SYSTEM VERIFICATION ................................................................................................... 20 SAR Test Report Report No.: 2014SAR0089 East China Institute of Telecommunications Page Number : 4 of 205 TEL: +86 21 63843300FAX:+86 21 63843301 Report Issued Date :August 16, 2014 9. MEASUREMENT PROCEDURES ...................................................................................... 21 9.1. TESTS TO BE PERFORMED ............................................................................................. 21 9.2. GENERAL MEASUREMENT PROCEDURE ...................................................................... 22 9.3. WCDMA MEASUREMENT PROCEDURES FOR SAR ...................................................... 23 9.4. BLUETOOTH & WI-FI MEASUREMENT PROCEDURES FOR SAR ................................ 24 9.5. POWER DRIFT ................................................................................................................... 25 10. CONDUCTED OUTPUT POWER ....................................................................................... 26 10.1. MANUFACTURING TOLERANCE ..................................................................................... 26 10.2. GSM MEASUREMENT RESULT ........................................................................................ 30 10.3. WCDMA MEASUREMENT RESULT .................................................................................. 31 10.4. WI-FI AND BT MEASUREMENT RESULT ......................................................................... 32 11. SIMULTANEOUS TX SAR CONSIDERATIONS ................................................................. 35 11.1. INTRODUCTION ..................................................…

Text truncated - open the document above for the full version.

Report No.: RXA1405-0124SAR Page 1 of 71 \ TESTING No. L2264 SAR TEST REPORT Product Name WCDMA Digital Mobile Phone Model Name V.35 / Nextel V.35 FCC ID 2AA9WV1001 Applicant VSN Technologies Inc. d/b/a VSN Mobile Manufacturer MOBIWIRE MOBILES (NINGBO) CO.,LTD Date of issue July 16, 2014 TA Technology (Shanghai) Co., Ltd. TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1405-0124SAR Page 2 of 71 GENERAL SUMMARY Reference Standard(s) FCC 47CFR §2.1093 Radiofrequency Radiation Exposure Evaluation: Portable Devices ANSI C95.1, 1992: Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.(IEEE Std C95.1-1991) IEEE Std 1528™-2003: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques. KDB 865664 D01 SAR measurement 100 MHz to 6 GHz v01r03: SAR Measurement Requirements for 100 MHz to 6 GHz KDB 447498 D01 Mobile Portable RF Exposure v05r02: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies KDB 648474 D04 Handset SAR v01r02: SAR Evaluation Considerations for Wireless Handsets. KDB 941225 D01 SAR test for 3G devices v02: SAR Measurement Procedures CDMA 20001x RTT, 1x Ev-Do, WCDMA, HSDPA/HSPA KDB 941225 D02 HSPA and 1x Advanced v02r02 SAR Guidance for HSPA, HSPA+, DC-HSDPA and 1x-Advanced Conclusion WCDMA Band IV: Pass Comment The test result only responds to the measured sample. Approved by Weizhong Yang Director Revised by Minbao Ling SAR Manager Performed by Yi Zhang SAR Engineer TA Technology (Shanghai) Co., Ltd. Test Report Report No.: RXA1405-0124SAR Page 3 of 71 TABLE OF CONTENT 1. General Information ..................................................................................................................... 5 1.1. Notes of the Test Report ....................................................................................................... 5 1.2. Testing Laboratory ................................................................................................................ 5 1.3. Applicant Information ............................................................................................................ 6 1.4. Manufacturer Information ...................................................................................................... 6 1.5. Information of EUT ................................................................................................................ 7 1.6. EUT Antenna Locations ........................................................................................................ 8 1.7. The Maximum Reported SAR 1g ............................................................................................ 9 1.8. Test Date .............................................................................................................................. 9 2. SAR Measurements System Configuration ................................................................................ 10 2.1. SAR Measurement Set-up .................................................................................................. 10 2.2. DASY5 E-field Probe System ............................................................................................. 11 2.2.1. EX3DV4 Probe Specification ....................................................................................... 11 2.2.2. E-field Probe Calibration .............................................................................................. 12 2.3. Other Test Equipment ......................................................................................................... 12 2.3.1. Device Holder for Transmitters .................................................................................... 12 2.3.2. Phantom ...................................................................................................................... 13 2.4. Scanning Procedure ........................................................................................................... 13 2.5. Data Storage and Evaluation .............................................................................................. 15 2.5.1. Data Storage ................................................................................................................ 15 2.5.2. Data Evaluation by SEMCAD ...................................................................................... 15 3. Laboratory Environment ............................................................................................................. 17 4. Tissue-equivalent Liquid ............................................................................................................ 18 4.1. Tissue-equivalent Liquid Ingredients ................................................................................... 18 4.2. Tissue-equivalent Liquid Properties .................................................................................... 19 5. System Check ............................................................................................................................ 20 5.1. Description of System Check .............................................................................................. 20 5.2. System Check Results ........................................................................................................ 21 6. Operational Conditions during Test ............................................................................................ 22 6.1. General Description of Test Procedures ............................................................................. 22 6.2. Test Positions ...................................................................................................................... 22 6.2.1. Against Phantom Head ................................................................................................ 22 6.…

Text truncated - open the document above for the full version.

Full TEST REPORT No. 2014RFW0089 For Client : VSN Technologies Inc. d/b/a VSN Mobil Production : WCDMA Digital Mobile Phone Model Name : V.35 / Nextel V.35 FCC ID: 2AA9WV1001 Model Number: V1001 Hardware Version: V01 Software Version: V01 Issued date: 2014-08-15 Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of ECIT Shanghai. Test Laboratory: ECIT Shanghai, East China Institute of Telecommunications Add: 7-8F, G Area, No.668, Beijing East Road, Huangpu District, Shanghai, P. R. China Tel: (+86)-021-63843300, E-Mail: [email protected] RF Test Report Report No.: 2014RFW0089 East China Institute of Telecommunications Page Number : 2 of 54 TEL: +86 21 63843300 FAX: +86 21 63843301 Report Issued Date : Aug 15, 2014 Revision Version Report Number Revision Date Memo 2014RFW0089 00 2014-07-22 Initial creation of test report 2014RFW0089 01 2014-08-08 Second creation of test report 2014RFW0089 02 2014-08-14 Third creation of test report 2014RFW0089 03 2014-08-15 The fourth creation of test report RF Test Report Report No.: 2014RFW0089 East China Institute of Telecommunications Page Number : 3 of 54 TEL: +86 21 63843300 FAX: +86 21 63843301 Report Issued Date : Aug 15, 2014 CONTENTS 1. TEST LABORATORY ............................................................................................ 5 1.1. TESTING LOCATION ............................................................................................ 5 1.2. TESTING ENVIRONMENT .................................................................................... 5 1.3. PROJECT DATA .................................................................................................... 5 1.4. SIGNATURE .......................................................................................................... 5 2. CLIENT INFORMATION ........................................................................................ 6 2.1. APPLICANT INFORMATION ................................................................................. 6 2.2. MANUFACTURER INFORMATION ....................................................................... 6 3. EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ........... 7 3.1. ABOUT EUT .......................................................................................................... 7 3.2. INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST ...................... 7 3.3. INTERNAL IDENTIFICATION OF AE USED DURING THE TEST ........................ 7 4. REFERENCE DOCUMENTS ................................................................................. 8 4.1. REFERENCE DOCUMENTS FOR TESTING ........................................................ 8 5. SUMMARY OF TEST RESULTS ........................................................................... 9 5.1. NOTES ................................................................................................................. 10 5.2. STATEMENTS...................................................................................................... 11 6. TEST RESULT ..................................................................................................... 12 6.1. MAXIMUM OUTPUT POWER .............................................................................. 12 6.1.1. MAXIMUM PEAK OUTPUT POWER-CONDUCTED ........................................... 12 6.1.2. MAXIMUM AVERAGE OUTPUT POWER-CONDUCTED ................................... 13 6.2. PEAK POWER SPECTRAL DENSITY ................................................................ 14 6.3. OCCUPIED 6DB BANDWIDTH ........................................................................... 19 6.4. BAND EDGES COMPLIANCE ............................................................................ 25 6.5. TRANSMITTER SPURIOUS EMISSION-CONDUCTED ..................................... 28 RF Test Report Report No.: 2014RFW0089 East China Institute of Telecommunications Page Number : 4 of 54 TEL: +86 21 63843300 FAX: +86 21 63843301 Report Issued Date : Aug 15, 2014 6.6. TRANSMITTER SPURIOUS EMISSION-RADIATED .......................................... 39 7. TEST EQUIPMENTS AND ANCILLARIES USED FOR TESTS .......................... 51 8. TEST ENVIRONMENT ......................................................................................... 52 ANNEX A. DEVIATIONS FROM PRESCRIBED TEST METHODS ............................ 54 RF Test Report Report No.: 2014RFW0089 East China Institute of Telecommunications Page Number : 5 of 54 TEL: +86 21 63843300 FAX: +86 21 63843301 Report Issued Date : Aug 15, 2014 1. Test Laboratory 1.1. Testing Location Company Name: ECIT Shanghai, East China Institute of Telecommunications Address: 7-8F, G Area, No. 668, Beijing East Road, Huangpu District, Shanghai, P. R. China Postal Code: 200001 Telephone: (+86)-021-63843300 Fax: (+86)-021-63843301 1.2. Testing Environment Normal Temperature: 15-35°C Extreme Temperature: -10/+55°C Relative Humidity: 20-75% 1.3. Project data Project Leader: Wangyaqiong Testing Start Date: 2014-06-01 Testing End Date: 2014-08-14 1.4. Signature Wang Daming (Prepared this test report) Liu Jianquan (Reviewed this test report) Zheng Zhongbin Director of the laboratory (Approved this test report) RF Test Report Report No.: 2014RFW0089 East China Institute of Telecommunications Page Number : 6 of 54 TEL: +86 21 63843300 FAX: +86 21 63843301 Report Issued Date : Aug 15, 2014 2. Client Information 2.1. Applicant Information Company Name: VSN Technologies Inc. d/b/a VSN Mobile Address: 1975 E. Sunrise Blvd. Suite 400, Fort Lauderdale FL Contact Person: Amit Verma Telephone: 954-609-4912 Postcode: 33304 2.2. Manufacturer Information Company Name: MOBIWIRE MOBILES (NINGBO) CO.,LTD Address: No.999,Dacheng East Road,Fenghua City,Zhejiang Contact Person: Xu linzhong Telephone: 0574 88916450 Postcode: 315500 RF Test Report Report No.: 2014RFW0089 Ea…

Text truncated - open the document above for the full version.

FCC Part 15C-Test Photograph

Picture1：Head Left Cheek Mode Picture2：Head Left Tilt Mode Picture3：Head Right Cheek Mode Picture4：Head Right Tilt Mode Picture5：Body Phantom Mode Picture6：Body Ground Mode Picture7：Body Left Mode Picture8：Body Right Mode Picture9：Body Bottom Mode Picture10：Body Top Mode