2AAAL-T041-315Remote

1 GARAGE DOOR OPENER Models 9357·9367 For Residential Use Only Owner’s Manual  Please read this manual and the enclosed safety materials carefully!  Fasten the manual near the garage door after installation.  The door WILL NOT CLOSE unless The safety is connected and properly aligned.  Periodic checks of the opener are required to ensure safe operation.  The model number label is located on the left side panel of your opener www.seaside.net.cn DALIAN SEASIDE DOOR CONTROLLING SYSTEM CO., LT D . TABLE OF CONTENTS Introduction 2-6 Assembly 7-9 Installation 10-18 Install The Wall Control 19-20 Install The Photo Eye Safety System 21-22 Power 23-24 Adjustments 24-28 Operation 29 Wall Control 30 Remote Control 30 To Erase the Memory 30 To Open the Door Manually 31 Maintenance 31 Repair Parts 32-33 Troubleshooting 34 2 WARNING WARNING WARNING WARNING INTRODUCTION Safety Symbol and Signal Word Review This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained and tested in strict accordance with the instructions and warnings contained in this manual. When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something or from electric shock. Read the warnings carefully. Mechanical Electrical When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your garage door and/or the garage door opener if you do not comply with the cautionary statements that accompany it. Read them carefully. Check your garage door 1 Disable locks and remove any ropes connected to the garage door. 2 Lift the door halfway up. Release the door. If balanced, it should stay in place, supported entirely by its springs. 3 Raise and lower the door to check for binding or sticking. If your door binds, sticks, or is out of balance, call a trained door systems technician. 4 Check the seal on the bottom of the door. Any gap between the floor and the bottom of the door must not exceed 1/4 inch (6 mm). Otherwise, the safety reversal system may not work properly. 5 The opener should be installed above the center of the door. If there is a torsion spring or center bearing plate in the way of the header bracket, it may be installed within 4 feet (1.2 m) to the left or right of the door center. See Installing the Header Bracket section. CAUTION To prevent possible SERIOUS INJURY or DEATH:  ALWAYS call a trained door systems technician if garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when required.  NEVER try to loosen, move or adjust garage door, door springs, cables, pulleys, brackets or their hardware, ALL of which are under EXTREME tension.  Disable ALL locks and remove ALL ropes connected to dBEFORE i t llidti CAUTION To prevent damage to garage door and opener:  ALWAYS disable locks BEFORE installing and operating the opener.  ONLY operate garage door opener at 120V, 60 Hz to avoid malfunction and damage. To reduce the risk of injury to persons Use this operator only with Sectional Door. 3 Tools needed During assembly, installation and adjustment of the opener, instructions will call for hand tools as illustrated below. 4 Overview/Carton Inventory GARAGE DOOR OPENER ASSEMBLY Overview/Carton Inventory A B C D E F G H I J K L M N P O Q A. Header bracket B. Pulley assembly C. Door bracket D. Curved door arm E. Straight door arm F. Trolley assembly G. Emergency release rope and handle H. Rail I. Rail Connectors(2) J. Hanging brackets（2） K. Garage door opener L. “U” rail clips（3） M. Safety reversing sensors N. Chain O. Sprocket and sprocket holder assembly P. Wall Control Panel Q. Safety labels and literature 5 ASSEMBLY HARDWARE Overview/Carton Inventory H1 Clevis Pin, long Φ8×80 (1) H2 Clevis Pin,short Φ8×30 (2) H3 Hex Nut M8(4) H4 Hex Bolt M8×20(4) H5 CotterΦ2×25(3) H6 Screw M5×20(2) H7 Lag Screw M8×40 (4) H8 Self-Threading Screw (2) 6 INCLUDED ACCESSORIES NOTE: Accessories will vary depending on the garage door opener model purchased. Depending on your specific model, other accessories may be included with your garage door opener. The instructions for these accessories will be attached to the accessory and are not included in this manual. The images throughout this manual are for reference and your product may look different. Wall Control Hardware ASSEMBLY Wall Control Panel Drywall Anchors (2) Screw M4×30 (2) Remote Control 7 1、Assemble the Rail To avoid installation difficulties, do not run the garage door opener until instructed to do so. 1.1 Carefully remove the hanging brackets , sprocket and sprocket holder assembly packaged inside the rail. 1.2 Align the rails on a flat surface as shown. The front rail has seven holes near the pulley assembly. The middle rail has two rail connectors. The behind rail has three holes near the end of rail. 1.3 Pull the rail connectors to the “U” hole position in the rail as shown(1). 1.4 Slide the front rail into the rail connector. Bend the “U”. 1.5 Pull out the chain, The chain and sprocket assemble together. 1.6 Slide the behing rail into the rail connector. Bend the “U”. 1.7 Fasten the sprocket and sprocket holder assembly with the screws (H6). CAUTION To prevent INJURY from pinching, keep hands and fingers away from the joints while assembling the rail Hanging brackets Sprocket and sprocket holder assembly Middle Rail Front Rail Behind Rail Rail connector 3 1 2 4 8 2、Tighten the Chain ASSEMBLY H6 6 5 2.1 To increase the tension and tighten the chain,turn the tension nut clockwise or adjustable wrench until the nut is spaced properly from the rail end -plate. 2.2 Once the nut is spaced correctly,any additional tightening will overtighten the chain and may cause damage to the system. 2.2 To loose the tension,turn nut counterclockwise. 2.5cm 9 3、Fasten the Rail to the gar…

Text truncated - open the document above for the full version.

SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Project and Product Certification Representative Authorization Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Revised wording (obsolete) 1.0 2.0 Sept–25-2007 Updated company template (current) 2.0 3.0 Jan-31-2012

SCS-F19: Confidentiality Request Letter Page 1 of 2 Rev 3.0 775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: [email protected] Confidentiality Request Letter Reason for Amendment (current / obsolete) Revision History Approved Date From To Initial Release (obsolete) 1.0 1.0 Nov-14-2006 Adding CFR 2.459 (obsolete) 1.0 2.0 August – 11 - 2008 Updated company template & Added text box (current) 2.0 3.0 Jan-31-2012 SCS-F19: Confidentiality Request Letter Page 2 of 2 Rev 3.0 Dalian Seaside Door Controlling System Co., Ltd (2013-08-07) To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD Subject: Permanent Confidentiality Request for FCC ID: 2AAAL-T041-315 We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Operational Description - Schematic The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.459 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Signature ____________________________________ Wei Zhao Dalian Seaside Door Controlling System Co., Ltd No. 23-7, Yaobei Road, Ganjingzi District, Dalian, Liaoning, China

Figure 1 The EUT-Front View Figure 2 The EUT-Back View

Label Location On EUT

Product Name: Remote Model No.: T041-315 FCC ID: 2AAAL-T041-315

Figure 3 The EUT-Inside View Figure 4 PCB of the EUT-Front View Figure 5 PCB of the EUT-Back View Antenna

Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AAAL-T041-315 Page 1 of 20 Report No.: 201303781F Shenzhen Anbotek Compliance Laboratory Limited Tel: (86)755-26066544 Fax:(86)755-26014772 www.anbotek.com FCC TEST REPORT for Dalian Seaside Door Controlling System Co., Ltd Remote Model No.: T041-315 Report Number : 201303781F Date of Test : Jul. 01~ Aug. 02, 2013 Date of Report : Aug. 06, 2013 Prepared for : Dalian Seaside Door Controlling System Co., Ltd Address : No. 23-7, Yaobei Road, Ganjingzi District, Dalian, Liaoning, China Prepared By : Shenzhen Anbotek Compliance Laboratory Limited Address : 1/F., Building 1, SEC Industrial Park, No.0409 Qianhai Road, Nanshan District, Shenzhen, Guangdong, China Tel: (86) 755-26066544 Fax: (86) 755-26014772 Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AAAL-T041-315 Page 2 of 20 Report No.: 201303781F Shenzhen Anbotek Compliance Laboratory Limited Tel: (86)755-26066544 Fax:(86)755-26014772 www.anbotek.com TABLE OF CONTENT Description Test Report Page 1. GENERAL INFORMATION ......................................................................................................... 4 1.1.Description of Device (EUT) ..................................................................................................................... 4 1.2.Description of Test Facility ....................................................................................................................... 5 1.3.Measurement Uncertainty .......................................................................................................................... 5 1.4.Test Summary ............................................................................................................................................ 6 2. MEASURING DEVICE AND TEST EQUIPMENT .................................................................... 7 3. TEST PROCEDURE ....................................................................................................................... 8 4. RADIATION INTERFERENCE .................................................................................................... 9 4.1. Requirements (15.231): ............................................................................................................................ 9 4.2 Test Procedure ........................................................................................................................................... 9 4.3 Test Results ................................................................................................................................................ 9 5. 20DB BANDWIDTH ..................................................................................................................... 11 5.1. Requirements (15.231): .......................................................................................................................... 11 5.2. EUT Setup .............................................................................................................................................. 11 5.3. Test Results ............................................................................................................................................. 11 6. DUTY CYCLE ............................................................................................................................... 13 6.1. EUT Setup .............................................................................................................................................. 13 6.2. Test Procedure ........................................................................................................................................ 13 6.3. Requirements & Result ........................................................................................................................... 13 7. ANTENNA APPLICATION ......................................................................................................... 16 7.1. Antenna requirement .............................................................................................................................. 16 7.2. Result ...................................................................................................................................................... 16 8. TEST PHOTO ................................................................................................................................ 17 8.1. Photo of Radiation Emission Test .......................................................................................................... 17 APPENDIX I (External Photos) (1 pages) APPENDIX II(Internal Photos) (2 pages) Shenzhen Anbotek Compliance Laboratory Limited FCC ID: 2AAAL-T041-315 Page 3 of 20 Report No.: 201303781F Shenzhen Anbotek Compliance Laboratory Limited Tel: (86)755-26066544 Fax:(86)755-26014772 www.anbotek.com TEST REPORT Applicant : Dalian Seaside Door Controlling System Co., Ltd Manufacturer : Dalian Seaside Door Controlling System Co., Ltd EUT : Remote Model No. : T041-315 Serial No. : N/A Trade Mark : Rating : DC 3V Measurement Procedure Used: FCC Part15 Subpart C, Paragraph 15.231 The device described above is tested by Shenzhen Anbotek Compliance Laboratory Limited to determine the maximum emission levels emanating from the device and the severe levels of the device can endure and its performance criterion. The measurement results are contained in this test report and Shenzhen Anbotek Compliance Laboratory Limited is assumed full of responsibility for the accuracy and completeness of these measurements. Also, this report shows that the EUT (Equipment Under Test) is technically compliant with the FCC Part 15 Subpart C requirements. This report applies to above tested sample only and shall not be reproduced in part without written approval of Shenzhen Anbotek Compliance Laboratory Limited. Date of Test : Jul. 01~ Aug. 02, 2013 Prepared by : (Tested Engineer / Rock Zeng ) Review…

Text truncated - open the document above for the full version.

1. Photo of Radiated Emission Test