2AAFH-WM2899Bluetooth speaker

Modern Bluetooth Speaker MODEL WM2899 INSTRUCTION MANUAL Operating Instructions BEFORE OPERATING THIS PRODUCT, READ, UNDERSTAND, AND FOLLOW THESE INSTRUCTIONS. Be sure to save this booklet for future reference. The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. The Lightning flash with arrowhead symbol, with an equilateral triangle is intended to alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE. SAFETY INSTRUCTIONS THESE IMPORTANT SAFETY INSTRUCTIONS ARE INCLUDED, AS APPLICABLE TO THE APPLIANCE, CONVEYING TO THE USER THE INFORMATION ITEMIZED BELOW 1. Read instructions - All the safety and operating instructions should be read before the appliance is operated. 2. Retain instructions - The safety and operating instructions should be retained for future reference. 3. Head Warnings - All warnings and cautions on the appliance and in the operating instructions should be adhered to. 4. Follow instructions - All operating and use instructions should be followed. 5. Water and Moisture - The appliance should not be used near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool or the like. 6. Wall or Ceiling Mounting - The appliance should not be mounted to a wall or ceiling. 7. Ventilation - The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug or similar surface that may block the ventilation openings, or placed in a built-in installation, such as a bookcase or cabinet, that may impede the flow of air through the ventilation openings. 8. Heat - The appliance should be situated away from neat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.. 9. Power Sources - The product should be operated only with the type of power supply indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operation instructions. 10. Grounding Polarization - This product may be equipped with a polarized alternating current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way this is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 11. Power-Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. 12. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 13. Nonuse periods - The power cord of the appliance should be unplugged from the outlet when left when left unused for a long period of time. 14. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are not spilled into the product case through product openings. 15. Damage Requiring Service - Unplug this product from the wall outlet and take it to qualified service personnel under the following conditions. a) When the power-supply cord or plug is damaged. b) If liquid has been spilled into, or objects have fallen into the product. c) If the product has been exposed to rain or water. d) If the product does not operate when used according to the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may interfere with the product’s normal operation. e) If the product has been dropped or damaged in any way. f) When the product exhibits a distinct change in performance-this indicates a need for service. 16. Servicing - The user should not attempt to service the product beyond that described in the operating instruction. All servicing should be referred to qualified service personnel. 17. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines, or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching power lines or circuits as contact with them might be fatal. 18. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static. Section 810 of the National Electrical Code ANSI/NEFA 70 provides information with respect to proper grounding of the mast and supporting structure, grounding conductress, location of antenna-discharge unit, size of grounding electrodes, and requirements for the grounding electrode (see figure). 19. Cleaning - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 20. Lightning - For added protection for this product during a lightning storm…

Text truncated - open the document above for the full version.

External Photos 1. EUT front view 2. EUT rear view 3. EUT left side view 4. EUT right side view 5. EUT top view 6. EUT bottom view 7. Accessories

FCC label and label location 1. Label 2. Label location

Internal Photos 1. EUT uncover view 2. Mainboard front view 3. Mainboard rear view 4. BT chip view 5. BT antenna view

Report No.: SZ14080026S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 2 of 9 DIRECTORY 1. TESTING LABORATORY .................................................................................................................... 3 1.1. IDENTIFICATION OF THE RESPONSIBLE TESTING LOCATION ..................................................................... 3 1.2. ACCREDITATION CERTIFICATE ................................................................................................................ 3 2. TECHNICAL INFORMATION .............................................................................................................. 4 2.1. IDENTIFICATION OF APPLICANT .............................................................................................................. 4 2.2. IDENTIFICATION OF MANUFACTURER ...................................................................................................... 4 2.3. EQUIPMENT UNDER TEST (EUT) ............................................................................................................ 4 2.3.1. PHOTOGRAPHS OF THE EUT ............................................................................................................... 5 2.3.2. IDENTIFICATION OF ALL USED EUT ...................................................................................................... 6 2.4. APPLIED REFERENCE DOCUMENTS ........................................................................................................ 6 3. DEVICE CATEGORY AND RF EXPOSURE LIMIT ............................................................................. 7 4. MEASUREMENT OF CONDUCTED PEAK OUTPUT POWER. ......................................................... 8 5. RF EXPOSURE EVALUATION ........................................................................................................... 9 Change History Issue Date Reason for change 1.0 Aug. 26, 2014 First edition Report No.: SZ14080026S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 3 of 9 1. TESTING LABORATORY 1.1. Identification of the Responsible Testing Location Name: Shenzhen Morlab Communications Technology Co., Ltd. Morlab Laboratory Address: FL.3, Building A, FeiYang Science Park, No.8 LongChang Road, Block 67, BaoAn District, ShenZhen, GuangDong Province, P. R. China 518101 FCC Registration Number: 695796 1.2. Accreditation Certificate Accredited Testing Laboratory: No. CNAS L3572 Report No.: SZ14080026S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 4 of 9 2. TECHNICAL INFORMATION Note: the following data is based on the information by the applicant. 2.1. Identification of Applicant Company Name: Winsonic Electric Limited Address: 17/F, Flat K Universal Ind. Center, 19-21 Shan Mei St., Fotan, Shatin, N.T. Hong Kong 2.2. Identification of Manufacturer Company Name: N/A Address: N/A 2.3. Equipment Under Test (EUT) Model Name: WM2899/SP305DG Trade Name: N/A Brand Name: Winsonic /SYLVANIA Hardware Version: N/A Software Version: N/A Frequency Bands: Bluetooth: 2402-2480MHz Modulation Mode: Bluetooth: GFSK Antenna type: Fixed Internal Antenna Development Stage: Identical prototype Report No.: SZ14080026S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 5 of 9 2.3.1. Photographs of the EUT 1. EUT front view 2. EUT rear view Report No.: SZ14080026S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 6 of 9 2.3.2. Identification of all used EUT The EUT identity consists of numerical and letter characters, the letter character indicates the test sample, and the following two numerical characters indicate the software version of the test sample. EUT Identity Hardware Version Software Version 1# N/A N/A 2.4. Applied Reference Documents Leading reference documents for testing: No. Identity Document Title 1 47 CFR§2.1091 Radiofrequency Radiation Exposure Evaluation: mobile devices 2 KDB 447498 D01v05r02 General RF Exposure Guidance Report No.: SZ14080026S01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 7 of 9 3. DEVICE CATEGORY AND RF EXPOSURE LIMIT Per user manual, this device is a Bluetooth Speaker. Based on 47CFR 2.1091, this device belongs to mobile device category with General Population/Uncontrolled exposure. Mobile Devices: 47CFR 2.1091(b) For purposes of this section, a mobile device is defined as a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. In this context, the term “fixed location” means that the device is physically secured at one location and is not able to be easily moved to another location. Transmitting devices designed to be used by consumers or workers that can be easily re-located, such as wireless devices associated with a personal computer, are considered to be mobile devices if they meet the 20 centimeter separation requirement. GENERAL POPULATION / UNCONTROLLED EXPOSURE The general population/uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercis…

Text truncated - open the document above for the full version.

Report No.:SZ14080026W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 2 of 42 TABLE OF CONTENTS 1. GENERAL INFORMATION ...................................................................................................................... 4 1.1. EUT DESCRIPTION .................................................................................................................................. 4 1.2. TEST STANDARDS AND RESULTS ............................................................................................................. 5 1.3. FACILITIES AND ACCREDITATIONS ............................................................................................................ 6 1.3.1. FACILITIES ....................................................................................................................................................... 6 1.3.2. TEST ENVIRONMENT CONDITIONS ................................................................................................................ 6 2. 47 CFR PART 15C REQUIREMENTS .................................................................................................... 7 2.1. ANTENNA REQUIREMENT ......................................................................................................................... 7 2.1.1. APPLICABLE STANDARD ................................................................................................................................. 7 2.1.2. RESULT: COMPLIANT ...................................................................................................................................... 7 2.2. NUMBER OF HOPPING FREQUENCY ......................................................................................................... 7 2.2.1. REQUIREMENT ................................................................................................................................................ 7 2.2.2. TEST DESCRIPTION ........................................................................................................................................ 7 2.2.3. TEST PROCEDURE ......................................................................................................................................... 8 2.2.4. TEST RESULT .................................................................................................................................................. 8 2.3. PEAK OUTPUT POWER ........................................................................................................................... 10 2.3.1. REQUIREMENT .............................................................................................................................................. 10 2.3.2. TEST DESCRIPTION ...................................................................................................................................... 10 2.3.3. TEST RESULT ................................................................................................................................................ 10 2.3.3.1. GFSK MODE ............................................................................................................................................. 11 2.4. 20DB BANDWIDTH .................................................................................................................................. 12 2.4.1. DEFINITION ................................................................................................................................................... 12 2.4.2. TEST DESCRIPTION ...................................................................................................................................... 12 2.4.3. TEST PROCEDURE ....................................................................................................................................... 12 2.4.4. TEST RESULT ................................................................................................................................................ 13 2.4.4.1. GFSK MODE ............................................................................................................................................. 13 2.5. CARRIED FREQUENCY SEPARATION ....................................................................................................... 15 2.5.1. DEFINITION ................................................................................................................................................... 15 2.5.2. TEST DESCRIPTION ...................................................................................................................................... 15 2.5.3. TEST PROCEDURE ....................................................................................................................................... 15 2.5.4. TEST RESULT ................................................................................................................................................ 16 2.6. TIME OF OCCUPANCY (DWELL TIME) ....................................................................................................... 17 2.6.1. REQUIREMENT .............................................................................................................................................. 17 2.6.2. TEST DESCRIPTION ...................................................................................................................................... 17 2.6.3. TEST PROCEDURE ....................................................................................................................................... 17 Report No.:SZ14080026W01 Shenzhen Morlab Communications Technology Co., Ltd Phone: +86 (0) 755 36698555 Web site: http://www.morlab.cn/ Fax: +86 (0) 755 36698525 Email: [email protected] Page 3 of 42 2.6.4. TEST RESULT ................................…

Text truncated - open the document above for the full version.

Test Setup Photos 1. Conducted emission main’s port front view 2. Conducted emission main’s port side view 3. Radiated emission (9KHz-30MHz) 4. Radiated emission (30MHz-1GHz) 5. Radiated emission (above 1GHz) 6. Conducted emission antenna’s port