2AAWQ-PR5RECEIVERPlay-Fi Receiver

FCC Notice Notice (Information to user): You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. For P15B equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co located or operating in conjunction with any other antenna or‐ transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Operations in the 5.15Ghz-5.25Ghz band are restricted to indoor usage only. IC Notice This device complies with Industry Canada license‐exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES‐003. Le present appareil est con forme aux CNR d'In dustrie Canada applicabl es aux appareils radio ex empts de licence. L'exploitation est autorisee aux deux conditions suivantes : (1) l'appareil nedoit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d'en co mpromettre le fonc tionnement. Radiation Exposure Statement: The product comply with the Canada portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible fro m the user body or set the device to lo wer output power if such function is available. Déclaration sur la radioexposition: Le produit est conforme à la limite d'exposition RF portable Canada définies pour un environnement non contrôlé et sont sans danger pour l'opération que celle décrite dans le présent manuel. La poursuite de la réduction de l'e xposition aux radiofréquences ne peut être attein t que si le produit peut être gardé le plus loin possible du corps de l'utilisateur ou de régler l'appareil pour une puissance de sortie inférieure si une telle fonction est disponible. Operations in the 5.15Ghz‐5.2 5Ghz ban d are restricted to indoor usage only. Les opérations dans la ban de de 5,15GHz - 5,25 GHz sont réservées à un usage en in térieur uniqueme nt.

A l) horu Phorus, Inc. Ventura Boulevard, Suite 3lorEncino, United States,9t436 TEL: 818.556.3995 xSLT Attestation for FGG Declaration of Gonformitv Brand: Phorus Model Number: PR5 Receiver Date:2013112105 FCG lD: 2AAWQ-PRSRECEIVER Please be notified that we, Phorus, Inc., would like to declare that the composite portion categorized as computer peripheral has been authorized under the Declaration of Conformity procedures. The test report numbers supporting the DoC is 1312FE12. Testing in regards to this report was done by A Test Lab Techno Gorp., located in No.140-l Ghangan Str., Bade City Taoyuan Gounty Taiwan, which has been accredited in accordance to all of the requirements of 47 GFR 2.948 (d) and (e) of the FCC rules and KD8349827. Sincerely, Matt Garroll / Senior Director, Program Development Phorus, lnc.

Date:201311215 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. SIEMIC,INC. 7 7 5 Montague Expressway Milpitas, CA 95035 To whom it may concern: I, the undersigned, hereby authorize Murphy Wang, Director of A Test Lab Techno Corp. and hereafter referred to as ATL, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Murphy Wang, Director of A Test Lab Techno Corp. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certif! that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21U.S.C. S53(a). In authorizing ATL as our agent,we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary affangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including intemal audit reports) and personnel for the pu{poses of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; 0 use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereofis used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product's compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and. any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, /"i L: Matt Carroll / Senior Director, Program Development Phorus, Inc. REMARK: 1. This authoization letter will be sent along with your application when filing with the Certifi cation Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact inFCC database.

A It phorus 2013t12t5 To. SlEMlC, lNC. 775 Montague Expressway, Milpitas, CA 95035 USA Dear Sir/Madam, Re: Project and Product Ceftification Representative Authorization Letter We, Phorus, lnc. hereby authorize SlEMlC, lNC. to act as a Ceftification Body for ceftifying for the following project(s): Product description. Play-Fi Receiver Model Number: PR5 Receiver FCC lD: 2AAWQ-PRSRECEIVER We affirm that between SIEMIC and Phorus, lnc., any difference in understanding, including test plan, measurement methods, applicable standards and relevant procedures and processes have been resolved prior to commencement of testing activities. Sincerely, sisnature: 44 4./'{ Matt Carroll I Senior Director, Program Development Phorus, lnc. SCS-F18: Project and Product Certification Representative Authorization Letter Page 1 of 1 Rev 3.0

l ti phorus 2013t12t5 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD subject: Permanent Gonfidentiality Request for FCC lD 2AAWQ- PR5RECEIVER We hereby request confidential treatment of information accompanying this application as outlined below: - Block Diagram - Schematics - OperationalDescription - Tune up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 & 0.4S9 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, 4t /U,4 Signature: ( Matt Carroll/ Senior Director, Program Development Phorus, lnc. SCS-Fl9: Confidentiality Request Letter page I of 1 Rev 3.0

1 of 7 External Photos Model Number: PR5 Receiver FCC ID: 2AAWQ-PR5RECEIVER IC: 11138A-PR5RECEIVER 2 of 7 EUT Photo 1 ) EUT Photo 2 ) 3 of 7 EUT Photo 3 ) EUT Photo 4 ) 4 of 7 EUT Photo 5 ) EUT Photo 6 ) 5 of 7 EUT Photo 7 ) EUT Photo 8 ) 6 of 7 EUT Photo 9 ) EUT Photo 10 ) 7 of 7 EUT Photo 11 ) EUT Photo 12 )

Label Info & Label Location FCC ID: 2AAWQ-PR5RECEIVER IC: 11138A-PR5RECEIVER Label Location: Bottom

1 of 10 Internal Photos Model Number: PR5 Receiver FCC ID: 2AAWQ-PR5RECEIVER IC: 11138A-PR5RECEIVER 2 of 10 EUT Photo 1 ) EUT Photo 2 ) 3 of 10 EUT Photo 3 ) EUT Photo 4 ) 4 of 10 EUT Photo 5 ) EUT Photo 6 ) 5 of 10 EUT Photo 7 ) EUT Photo 8 ) WiFi Antenna 6 of 10 EUT Photo 9 ) EUT Photo 10 ) BT Antenna 7 of 10 EUT Photo 11 ) EUT Photo 12 ) 8 of 10 EUT Photo 13 ) EUT Photo 14 ) 9 of 10 EUT Photo 15 ) EUT Photo 16 ) 10 of 10 EUT Photo 17 ) EUT Photo 18 )

A Test Lab Techno Corp. Changan Lab：No. 140 -1, Changan Street, Bade City, Taoyuan County, Taiwan R.O.C. Te l：886-3-271-0188 / Fax：886-3-271-0190 MPE Report Test Report No. ： 1312FS11 Applicant ： Phorus, Inc. Product Type ： Play-Fi Receiver Trade Name ： Phorus Model Number ： PR5 Receiver Dates of Receive ： Apr. 18, 2013 Dates of Test ： Apr. 29, 2013 Issued Date ： Dec. 06, 2013 Test Specification ： 47 CFR § 2.1091 47 CFR §1.1310 ANSI / IEEE Std.C95.1-1992 H46-2/99-237E Location of Test Lab. ： Chang-an Lab. 1. The test operations have to be performed with cautious behavior, the test results are as attached. 2. The test results are under chamber environment of A Test Lab Techno Corp. A Test Lab Techno Corp. does not assume responsibility for any conclusions and generalizations drawn from the test results with regard to other specimens or samples. 3. The measurement report has to be written approval of A Test Lab Techno Corp. It may only be reproduced or published in full. This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. 4. This document may be altered or revised by A Test Lab Techno. Corp. personnel only, and shall be noted in the revision section of the document. Approved By ： Tested By ： (Bill Hu) (Sky Chou) ©2013 A Test Lab Techno Corp. Report Number: 1312FS11Page 1 of 12 Contents 1. Description of Equipment under Test (EUT)............................................................... 3 2. Human Exposure Assessment .................................................................................... 4 3. RF Output Power........................................................................................................... 5 4. Test Result................................................................................................................... 10 ©2013 A Test Lab Techno Corp. Report Number: 1312FS11Page 2 of 12 1. Description of Equipment under Test (EUT) Applicant Phorus, Inc. Applicant Address 7669 Limestone Drive Gainesville, VA 20155-4038 USA Manufacturer Wistron InfoComm (Zhongshan) Corporation Linhai Branch Manufacturer Address Xiyiwei, Ma'an Cun, Zhongshan Torch Development Zone, Zhongshan City, Guangdong, China Product Type Play-Fi Receiver Trade Name Phorus Model Number PR5 Receiver FCC ID 2AAWQ-PR5RECEIVER IC 11138A-PR5RECEIVER Frequency Range IEEE 802.11b / 802.11g / 802.11n (2.4GHz) 20MHz: 2412 -2462 MHz IEEE 802.11n (2.4GHz) 40MHz: 2422 - 2452 MHz IEEE 802.11a / 802.11n (5GHz) 20MHz: 5180 - 5850 MHz IEEE 802.11n (5GHz) 40MHz: 5190 - 5795 MHz Bluetooth: 2402 - 2480 MHz Antenna Used Item Antenna Type Band Max. Gain IEEE 802.11b / 802.11g IEEE 802.11n (2.4GHz) 20MHz / 40MHz 1.18 dBi IEEE 802.11a IEEE 802.11n (5GHz) 20MHz / 40MHz U-NII Band I/II/III 3.05 dBi 1 Main ANT (ANTL) PIFA IEEE 802.11a IEEE 802.11n (5GHz) 20MHz / 40MHz U-NII Band IV 3.18 dBi IEEE 802.11b / 802.11g IEEE 802.11n (2.4GHz) 20MHz / 40MHz 3.93 dBi IEEE 802.11a IEEE 802.11n (5GHz) 20MHz / 40MHz U-NII Band I/II/III 5.38 dBi 2 Aux ANT (ANTR) PIFA IEEE 802.11a IEEE 802.11n (5GHz) 20MHz / 40MHz U-NII Band IV 4.18 dBi 3 Bluetooth ANT PrintingBluetooth 2.52 dBi Temperature Range -30 ~ +70°C The above equipment was tested by A Test Lab Techno Corp. For compliance with the requirements set forth in 47 CFR § 2.1091 & 47 CFR § 1.1310. The results of testing in this report apply only to the product/system, which was tested. Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties ©2013 A Test Lab Techno Corp. Report Number: 1312FS11Page 3 of 12 2. Human Exposure Assessment Due to the design and installation of this product, it is not possible to conduct SAR evaluation. This is because client either manufactures or supplies the antenna(s) that will be used in the installation of this product. Therefore, this product will be evaluated as a mobile device per 47 CFR §1.1310 titled “Radiofrequency radiation exposure limits”, generally referred to as MPE limits. In 47 CFR § 2.1091, paragraph (b) defines a mobile device as “a transmitting device designed to be used in other than fixed locations and to generally be used in such a way that a separation distance of at least 20 cm is normally maintained between the transmitter’s radiating structure(s) and the body of the user or nearby persons. ” This product is intended to be installed into a vehicle such that the unit is physically secured at one location. In the installation guide supplied with the product, Client has made the following statement: “IMPORTANT: To meet the FCC’s RF Exposure Guidelines, the antenna should be installed so there is at least 20 cm of separation between the body of the user and nearby persons and the antenna”. Based on the installation of the transceiver and the antenna, the transmitters radiating structure is more than 20 cm from the user. Thus, this product is a “mobile device” as defined in section § 2.1091 paragraph (b). Exposure evaluation Equation from page 18 of OET Bulletin 65, Edition 97-01 2 4R PG S π = Where S: power density P: power input to the antenna G: power gain of the antenna in the direction of interest relative to an isotropic radiator. R: distance to the center of radiation of the antenna. ©2013 A Test Lab Techno Corp. Report Number: 1312FS11Page 4 of 12 3. RF Output Power Time-Avg. Conducted power (dBm) Band Date Rate CH Frequency (MHz) Main AUX 1 2412.0 14.40 14.30 6 2437.0 13.71 13.61 1M 11 2462.0 13.75 13.65 2M 6 2437.0 13.66 13.57 5.5M 6 2437.0 13.62 13.55 IEEE 802.11b 11M 6 2437.0 13.59 13.53 1 2412.0 13.06 12.93 6 2437.0 13.73 13.60 6M 11 2462.0 13.37 13.24 9M 6 2437.0 13.69 13.56 12M 6 2437.0 13.63 13.50 18M 6 2437.0 13.57 13.44 24M 6 2437.0 13.51 13.38 36M 6 2437.0 13.43 13.30 48M 6 2437.0 13.35 13.22 IEEE 802.11g 54M 6 2437.0 13.31 13.18 1 2412.0 12.47 12.33 6 2437.0 12.19 12.05 6.5M 11 2462.0 12.42 12.28 13M 6 2437.0 12.15 12.01 19.5M 6 2437.0 12.07 11.93 26M 6 2437.0 11.99 11.85 39…

Text truncated - open the document above for the full version.

FCC 47 CFR PART 15 SUBPART C Product Type ： Play-Fi Receiver Applicant ： Phorus, Inc. Address ： 16255 Ventura Boulevard, Suite 310,Encino ,United States,91436 Trade Name ： Phorus Model Number ： PR5 Receiver Test Specification ： FCC 47 CFR PART 15 SUBPART C: Oct., 2012 Canada RSS-210 ISSUE 8: Dec., 2010 Canada RSS-Gen ISSUE 3: Dec., 2010 ANSI C63.4-2009 Receive Date ： Apr. 18, 2013 Test Period ： Apr. 30~May 16, 2013 Issue Date ： Dec. 06, 2013 Issue by A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 Note: This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno Corp. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, or any government agencies. The test results in the report only apply to the tested sample. A Test Lab Techno Corp. Report Number: 1312FR14 1 of 85 Revision History Rev. Issue Date Revisions Revised By 00 Dec. 06, 2013 Initial Issue A Test Lab Techno Corp. Report Number: 1312FR14 2 of 85 Verification of Compliance Issued Date: 12/06/2013 Product Type : Play-Fi Receiver Applicant : Phorus, Inc. Address : 16255 Ventura Boulevard, Suite 310,Encino ,United States, 91436 Trade Name : Phorus Model Number : PR5 Receiver FCC ID : 2AAWQ-PR5RECEIVER IC : 11138A-PR5RECEIVER EUT Rated Voltage : DC 12V, 2A Test Voltage : 120 Vac / 60 Hz Applicable Standard : FCC 47 CFR PART 15 SUBPART C: Oct., 2012 Canada RSS-210 ISSUE 8: Dec., 2010 Canada RSS-Gen ISSUE 3: Dec., 2010 ANSI C63.4-2009 Test Result : Complied Performing Lab. : A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 http://www.atl-lab.com.tw/e-index.htm The above equipment was tested by A Test Lab Techno Corp. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample tested as described in this report is in compliance with the requirements of FCC Rules Part 15.207, 15.209, 15.247 . The test results of this report relate only to the tested sample identified in this report. Approved By ： Reviewed By ： (Manager) (Cran Yang) (Testing Engineer) (Fly Lu) A Test Lab Techno Corp. Report Number: 1312FR14 3 of 85 TABLE OF CONTENTS 1 General Information .........................................................................................................6 2 EUT Description................................................................................................................7 3 Test Methodology.............................................................................................................8 3.1. Mode of Operation......................................................................................................8 3.2. EUT Exercise Software ..............................................................................................9 3.3. Configuration of Test System Details..........................................................................9 3.4. Test Site Environment...............................................................................................10 4 Conducted Emission Measurement..............................................................................11 4.1. Limit.......................................................................................................................... 11 4.2. Test Instruments ....................................................................................................... 11 4.3. Test Setup ................................................................................................................11 4.4. Test Procedure .........................................................................................................12 4.5. Test Result................................................................................................................13 5 Radiated Emission Measurement .................................................................................15 5.1. Limit..........................................................................................................................15 5.2. Test Instruments .......................................................................................................15 5.3. Setup ........................................................................................................................16 5.4. Test Procedure .........................................................................................................17 5.5. Test Result................................................................................................................19 6 Maximum Conducted Output Power Measurement.....................................................31 6.1. Limit..........................................................................................................................31 6.2. Test Setup ................................................................................................................31 6.3. Test Instruments .......................................................................................................31 6.4. Test Procedure .........................................................................................................31 6.5. Test Result................................................................................................................32 7 6dB RF Bandwidth & 99 % Occupied Bandwidth Measurement ................................38 7.1. Limit.....................................................................…

Text truncated - open the document above for the full version.

Part 15C Test Setup Photographs Conducted Emissions Test Configuration: Front View Rear View A Test Lab Techno Corp. Report Number: 1312FR14 1 of 3 Radiated Emissions Test Configuration: Below 1GHz _ Front View Below 1GHz _ Rear View A Test Lab Techno Corp. Report Number: 1312FR14 2 of 3 Above 1GHz _ Front View Above 1GHz _ Rear View A Test Lab Techno Corp. Report Number: 1312FR14 3 of 3