2ABES-KR2109Ultra10

 HoverCam.com HoverCam.com 1.Powering On To first use the Ultra 10,you can plug the included power cord into an available power outlet ,and plug the other end of the cord into the Ultra 10 Type-c outlet . When the battery is full, you can remove the power cord and power it directly through the battery Next ,press and hold the power button for five seconds . Boot-up time is approximately 60 seconds. to power outlet To connect Ultra 10 with HDMI,simply insert an HDMI cable to the HDMI-Out port on the Ultra 10 and the display you wish to use .Make sure the HDMI Switch is set to “OUT”. 2.Connecting to Display Interactive Display The Ultra 10 can be operated with a U Disk,with bluetooth mouse or wired mouse, 3.Connecting to Display Bluetooth Mouse Wired Mouse U Disk andthekeyboard Installation: Before use the DotCam RED, You need to install the “Flex 11".you can download the software on “”,then you found the Support Menu,and Click to Download,Then selectwww.HoverCam.com "HoverCam Flex 11" for download 10 10 HoverCam.com FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).                                                  This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Pathway Innovations and Technologies, Inc. 9985 Pacific Heights Blvd., Suite 100 San Diego, CA 92121, USA Pathway Innovations and Technologies, Inc. FCC ID: 2ABES-KR2109 Model Number: KR2109, Ultra9,Ultra10,Ultra11,Ultra12,Ultra13,Ultra15,Ultra16 DATE: Nov 29, 2019 To Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 We, Pathway Innovations and Technologies, Inc. declare that this EUT (FCC ID: 2AVE7-D019) doesn’t have Ad Hoc mode function on “non-US/Canada frequencies”. In addition. The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Best Regards! Name: Garry Wu Company: Pathway Innovations and Technologies, Inc. Address: 9985 Pacific Heights Blvd., Suite 100 San Diego, CA 92121, USA Phone: 18582430237 Fax: 858-750-3499 E-Mail: [email protected]

Pathway Innovations and Technologies, Inc. 9985 Pacific Heights Blvd., Suite 100 San Diego, CA 92121, USA Agent Authorization Date: Nov 29, 2019 Company: Pathway Innovations and Technologies, Inc. Address: 9985 Pacific Heights Blvd., Suite 100 San Diego, CA 92121, USA Product Description: Ultra10 FCC ID Number: FCC ID: 2ABES-KR2109 Tested Model Number: KR2109 We authorize Eurofins Product Service GmbH, Storkower Strasse 38c, D-15526 Reichenwalde, Germany, to act on our behalf on all matters concerning the certification of above mentioned equipment. We declare that Eurofins Product Service GmbH is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We, Pathway Innovations and Technologies, Inc., the undersigned, hereby authorize Shenzhen Toby Technology Co., Ltd. (Ivan Su, Supervisor of EMC Dep.), Shenzhen Microwave Certification Services Co., Ltd. (Gilbert Lui, Marketing Manager) and Ka.Ma.S UG (Karin Schmidt, CEO) on our behalf, to apply to the Federal Communications Commission on our equipment. We, the undersigned, hereby authorize Shenzhen Toby Technology Co., Ltd. (Ivan Su, Supervisor of EMC Dep.) to act on our behalf in matters relating to the application for a FCC equipment authorization for mentioned FCC ID Number including the signing of Form 731, necessary forms and documents in connection with this application. Any and all acts carried out by Shenzhen Toby Technology Co., Ltd. (Ivan Su, Supervisor of EMC Dep.) on our behalf shall have the same effect as acts of our own. This authorization expires on 31th December, 2019. Yours Sincerely, Pathway Innovations and Technologies, Inc. <Signature of Garry Wu > ----------------------------------------------------------------------------------- Garry Wu 9985 Pacific Heights Blvd., Suite 100 San Diego, CA 92121, USA Phone: 18582430237 Email: [email protected]

Pathway Innovations and Technologies, Inc. Declaration Letter of Model Difference Date: Dec 04, 2019 FCC ID Number: FCC ID: 2ABES-KR2109 Tested Model Number: Ultra10 Adding Model Number(s): Ultra9,Ultra10,Ultra11,Ultra12,Ultra13,Ultra15,Ultra16 All Adding Model Number(s) is/are same electrically identical as Tested Model Number. Yours Sincerely, Pathway Innovations and Technologies, Inc. <Signature of Garry Wu > ----------------------------------------------------------------------------------- Garry Wu 9985 Pacific Heights Blvd., Suite 100 San Diego, CA 92121, USA Phone: 18582430237 Email: [email protected]

Pathway Innovations and Technologies, Inc. CONFIDENTIALITY REQUEST for Certification under the FCC Rules Date: Nov 29, 2019 Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we request confidentiality for the following product: FCC ID Number: FCC ID: 2ABES-KR2109 Tested Model Number: KR2109 For the product stated above, we request that the following information be held confidential: Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days Block Diagram Schematic Diagram/ Circuit Diagram Circuit Description/ Operational Description Software Security Requirements Parts List Tune Up Information User’s Manual External Photos Internal Photos Test Setup Photos The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. Please do not hesitate to contact me if you have any queries. Yours Sincerely, Pathway Innovations and Technologies, Inc. <Signature of Garry Wu > ----------------------------------------------------------------------------------- Garry Wu 9985 Pacific Heights Blvd., Suite 100 San Diego, CA 92121, USA Phone: 18582430237 Email: [email protected]

Page : 4 of 14 TB-RF-075-1.0 Appendix III EUT External Photographs Model: KR2109 Photo 1 External of EUT Page : 5 of 14 TB-RF-075-1.0 Page : 6 of 14 TB-RF-075-1.0 Page : 7 of 14 TB-RF-075-1.0

Page : 1 of 14 TB-RF-074-1.0 Appendix IFCC ID Label Model: KR2109 Wide & length:62mm *25mm FCC ID: 2ABES-KR2109 Model: Ultra9 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2ABES-KR2109 Model: Ultra10 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Page : 2 of 14 TB-RF-075-1.0 FCC ID: 2ABES-KR2109 Model: Ultra11 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2ABES-KR2109 Model: Ultra12 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2ABES-KR2109 Model: Ultra13 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2ABES-KR2109 Model: Ultra15 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: 2ABES-KR2109 Model: Ultra16 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Page : 3 of 14 TB-RF-075-1.0 Appendix II ID Label Location ID LOCATION

Page : 8 of 14 TB-RF-075-1.0 Appendix IV EUT Internal Photographs Model: KR2109 Photo 2 Internal of EUT Page : 9 of 14 TB-RF-075-1.0 Page : 10 of 14 TB-RF-075-1.0 Page : 11 of 14 TB-RF-075-1.0 Page : 12 of 14 TB-RF-075-1.0

Shenzhen Toby Technology Co., Ltd. Report No.: TB-MPE169703 Page: 1 of 4 TB-RF-074-1.0 1A/F., Bldg.6, Yusheng Industrial Zone, The National Road No.107 Xixiang Section 467, Xixiang, Bao’an, Shenzhen, China Tel: +86 75526509301 Fax: +86 75526509195 RF Exposure Evaluation FCC ID: 2ABES-KR2109 1. Client Information Applicant : Pathway Innovations and Technologies, Inc. Address : 9985 Pacific Heights Blvd., Suite 100 San Diego, CA 92121, USA Manufacturer : ShenZhen KerunVisual Technology Co., LTD. Address : Unit A, F/11, Bldg.1, Senyang Electronic Technology Park, Tianliao Community, Guangming High Tech Zone, Guangming New District, Shenzhen, China 518132 2. General Description of EUT EUT Name : Ultra10 Models No. : KR2109,Ultra9,Ultra10,Ultra11,Ultra12,Ultra13,Ultra15,Ultra16 Model Difference : All these models are in the same PCB, layout and electrical circuit, the only difference is model No. Product Description : Operation Frequency: 2.4G: 802.11b/g/n(HT20): 2412MHz~2462MHz Bluetooth 4.1(BLE): 2402MHz~2480MHz 5G: U-NII-1: 5180MHz~5240MHz Modulation Type: 802.11b: DSSS(CCK, DQPSK, DBPSK) 802.11g/n: OFDM(BPSK,QPSK,16QAM, 64QAM) 802.11a: OFDM (QPSK, BPSK, 16QAM) 802.11ac: OFDM (QPSK, BPSK, 16QAM, 64QAM, 256QAM) BLE: GFSK Power Supply : AC Adapter(JHD-AP045U-PD-CS502): Input: AC 100-240V, 50/60Hz, 1.5A Output: DC 5V, 3A/9V-3A/12V-3A/15V-3A/20V-2.25A DC 3.8V by 12000mAh Li-ion battery. Software Version : Android 7.1.2 Hardware Version : V0.7 Connecting I/O Port(S) : Please refer to the User's Manual Remark : The adapter and antenna gain provided by the applicant, the verified for the RF conduction test provided by TOBY test lab. Note: More test information about the EUT please refer the RF Test Report. Report No.: TB-MPE169703 Page: 2 of 4 TB-RF-074-1.0 SAR Test Exclusion Calculations 1. FCC: According to KDB 447498 D01 Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies v06. (1) Clause 4.3: General SAR test reduction and exclusion guidance Sub clause 4.31: Standalone SAR test exclusion considerations 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6GHz at test separation distance≤5 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√f (GHz) ] ≤3.0 for 1-g SAR [(max. power of channel, including tune-up tolerance, mW)/(min. test separation, mm)]*[√f (GHz) ] ≤7.5.0 for 10-g SAR Report No.: TB-MPE169703 Page: 3 of 4 TB-RF-074-1.0 2. Calculation: Test separation: 5mm 2.4G WiFi Mode(802.11b) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2.412 8.12 8±0.5 8.5 7.079 2.199 3.0 2.437 8.08 8±0.5 8.5 7.079 2.210 3.0 2.462 8.14 8±0.5 8.5 7.079 2.222 3.0 2.4G WiFi Mode(802.11g) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2.412 7.89 8±0.5 8.5 7.079 2.199 3.0 2.437 7.96 8±0.5 8.5 7.079 2.210 3.0 2.462 7.78 8±0.5 8.5 7.079 2.222 3.0 2.4G WiFi Mode(802.11n(HT20)) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2.412 7.85 8±0.5 8.5 7.079 2.199 3.0 2.437 7.84 8±0.5 8.5 7.079 2.210 3.0 2.462 7.83 8±0.5 8.5 7.079 2.222 3.0 Report No.: TB-MPE169703 Page: 4 of 4 TB-RF-074-1.0 Test separation: 5mm BLE Mode (GFSK) Frequency (GHz) Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value 2.402 -0.977 -1±1 0 1 0.310 3.0 2.442 -1.225 -1±1 0 1 0.313 3.0 2.480 -1.575 -1±1 0 1 0.315 3.0 Test separation: 5mm 5G WiFi Mode Worst Conducted Power (dBm) Turn-up Power Tolerance (dB) Max power of tune up tolerance (dbm) Max power of tune up tolerance (mw) Calculation Value Threshold Value U-NII-1 (5180MHz) 6.98 6.5±0.5 7 5.012 2.281 3.0 Test separation: 5mm The worst RF Exposure Evaluation Worst Calculation Value Total Calculation Value Threshold Value 5G WiFi Mode 2.281 2.281 3.0 The measurement results comply with the FCC Limit per 47 CFR 2.1093 for the uncontrolled RF Exposure and SAR Exclusion Threshold per KDB 447498 v06. -----END OF REPORT-----

Shenzhen Toby Technology Co., Ltd. Report No.: TB-FCC169700 Page: 1 of 45 TB-RF-074-1.0 1A/F., Bldg.6, Yusheng Industrial Zone, The National Road No.107 Xixiang Section 467, Xixiang, Bao’an, Shenzhen, China Tel: +86 75526509301 Fax: +86 75526509195 FCC Radio Test Report FCC ID: 2ABES-KR2109 Original Grant Report No. : TB-FCC169700 Applicant : Pathway Innovations and Technologies, Inc. Equipment Under Test (EUT) EUT Name : Ultra10 Model No. : KR2109 Serial Model No. : Ultra9,Ultra10,Ultra11,Ultra12,Ultra13,Ultra15,Ultra16 Brand Name : HoverCam Receipt Date : 2019-10-18 Test Date : 2019-10-18 to 2019-11-25 Issue Date : 2020-01-02 Standards : FCC Part 15: 2019, Subpart C(15.247) Test Method : ANSI C63.10: 2013 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above, Test/Witness Engineer : Garen Engineer Supervisor : Ivan Su Engineer Manager : Ray Lai This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Report No.: TB-FCC169700 Page: 2 of 45 TB-RF-074-1.0 Contents CONTENTS ............................................................................................................................................. 2 1. GENERAL INFORMATION ABOUT EUT ............................................................................. 5 1.1 Client Information ................................................................................................................. 5 1.2 General Description of EUT (Equipment Under Test) ................................................... 5 1.3 Block Diagram Showing the Configuration of System Tested ...................................... 6 1.4 Description of Support Units .............................................................................................. 7 1.6 Description of Test Software Setting ................................................................................ 8 1.7 Measurement Uncertainty .................................................................................................. 8 1.8 Test Facility ........................................................................................................................... 9 2. TEST SUMMARY ..................................................................................................................... 10 3. TEST EQUIPMENT .................................................................................................................. 11 4. CONDUCTED EMISSION TEST ........................................................................................... 11 4.1 Test Standard and Limit .................................................................................................... 12 4.2 Test Setup ........................................................................................................................... 12 4.3 Test Procedure ................................................................................................................... 12 4.4 EUT Operating Mode ........................................................................................................ 13 4.5 Test Da5ta ........................................................................................................................... 13 5. RADIATED EMISSION TEST ................................................................................................ 14 5.1 Test Standard and Limit .................................................................................................... 14 5.2 Test Setup ........................................................................................................................... 15 5.3 Test Procedure ................................................................................................................... 16 5.4 EUT Operating Condition ................................................................................................. 17 5.5 Test Data ............................................................................................................................. 17 6. RESTRICTED BANDS REQUIREMENT ............................................................................. 18 6.1 Test Standard and Limit .................................................................................................... 18 6.2 Test Setup ........................................................................................................................... 18 6.3 Test Procedure ................................................................................................................... 18 6.4 EUT Operating Condition ................................................................................................. 19 6.5 Test Data ............................................................................................................................. 19 7. BANDWIDTH TEST ................................................................................................................. 20 7.1 Test Standard and Limit .................................................................................................... 20 7.2 Test Setup ........................................................................................................................... 20 7.3 Test Procedure ................................................................................................................... 20 7.4 EUT Operating Condition ................................................................................................. 20 7.5 Test Data ............................................................................................................................. 20 8. PEAK OUTPUT POWER TEST .......................................................…

Text truncated - open the document above for the full version.

Shenzhen Toby Technology Co., Ltd. Report No.: TB-FCC169701 Page: 1 of 78 TB-RF-074-1.0 1A/F., Bldg.6, Yusheng Industrial Zone, The National Road No.107 Xixiang Section 467, Xixiang, Bao’an, Shenzhen, China Tel: +86 75526509301 Fax: +86 75526509195 FCC Radio Test Report FCC ID: 2ABES-PILOTX01 Original Grant Report No. : TB-FCC169701 Applicant : Pathway Innovations and Technologies, Inc. Equipment Under Test (EUT) EUT Name : Ultra10 Model No. : KR2109 Serial Model No. : Ultra9,Ultra10,Ultra11,Ultra12,Ultra13,Ultra15,Ultra16 Brand Name : HoverCam Receipt Date : 2019-10-18 Test Date : 2019-10-18 to 2019-11-25 Issue Date : 2020-01-02 Standards : FCC Part 15, Subpart C (15.247:2019) Test Method : ANSI C63.10: 2013 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above, Test/Witness Engineer : Garen Engineer Supervisor : Ivan Su Engineer Manager : Ray Lai This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Report No.: TB-FCC169701 Page: 2 of 78 TB-RF-074-1.0 Revision History Report No. Version Description Issued Date TB-FCC169701 Rev.01 Initial issue of report 2020-01-02 Report No.: TB-FCC169701 Page: 3 of 78 TB-RF-074-1.0 Contents CONTENTS ............................................................................................................................................. 3 1. GENERAL INFORMATION ABOUT EUT ............................................................................. 5 1.1 Client Information ................................................................................................................. 5 1.2 General Description of EUT (Equipment Under Test) ................................................... 5 1.3 Block Diagram Showing the Configuration of System Tested ...................................... 6 1.4 Description of Support Units .............................................................................................. 6 1.5 Description of Test Mode .................................................................................................... 7 1.6 Description of Test Software Setting ................................................................................ 8 1.7 Measurement Uncertainty .................................................................................................. 8 1.8 Test Facility ........................................................................................................................... 9 2. TEST SUMMARY ..................................................................................................................... 10 3. TEST EQUIPMENT .................................................................................................................. 11 4. CONDUCTED EMISSION TEST ........................................................................................... 11 4.1 Test Standard and Limit .................................................................................................... 12 4.2 Test Setup ........................................................................................................................... 12 4.3 Test Procedure ................................................................................................................... 12 4.4 EUT Operating Mode ........................................................................................................ 13 4.5 Test Data ............................................................................................................................. 13 5.1 Test Standard and Limit .................................................................................................... 16 5.2 Test Setup ........................................................................................................................... 17 5.3 Test Procedure ................................................................................................................... 18 5.4 EUT Operating Condition ................................................................................................. 19 5.5 Test Data ............................................................................................................................. 19 5. RESTRICTED BANDS REQUIREMENT ............................................................................. 43 6.1 Test Standard and Limit .................................................................................................... 43 6.2 Test Setup ........................................................................................................................... 43 6.3 Test Procedure ................................................................................................................... 43 6.4 EUT Operating Condition ................................................................................................. 44 6.5 Test Data ............................................................................................................................. 44 6. BANDWIDTH TEST ................................................................................................................. 60 7.1 Test Standard and Limit .................................................................................................... 60 7.2 Test Setup ........................................................................................................................... 60 7.3 Test Procedure ................................................................................................................... 60 7.4 EUT Operating Condition ................................................................................................. 60 7.5 Test Data .................................…

Text truncated - open the document above for the full version.

Page : 11 of 12 TB-RF-075-1.0 Appendix V EUT Test Photographs 15C Test Setup Model: KR2109 Photo of Setup for Radiated Emission (Below 1 GHz) Photo of Setup for Radiated Emission (Above 1 GHz) Page : 12 of 12 TB-RF-075-1.0 Photo of Setup for Conducted Emission -----END OF REPORT-----