2ABLX-150562ZZigbee Hardwired Dual Channel Switch

The Watt Stopper Inc., d/b/a Qmotion

Click to zoom

Application Details

Equipment Class: DTS - Digital Transmission System
Date of Grant: Jan 27, 2016
Application Purpose: Original Equipment
Date of Application: Jan 27, 2016
Equipment Note: Zigbee Hardwired Dual Channel Switch
Frequency Range: 2405.00000000 - 2480.00000000
Company: The Watt Stopper Inc., d/b/a Qmotion
Country: United States

Documents & Files

Select a file to view

Document Text

Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.

Users Manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: 2ABLX-150562Z IC: 8832A-150562Z FCC Rule Part: 15.247 IC Radio Standards Specification: RSS-247 ACS Project Number: 15-0413 Manufacturer: Qmotion Incorporated Model: QM150562Z 8 REVISION 1.1 07DEC15 REVISION 1.1 07DEC15 Part # Part # QMotion ZigBee Hard Wired Control Roller Shade Application Guide FCC Warning: Changes or modifications to this device not expressly approved by QMotion ® Incorporated -Advanced Shading Systems could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not in- stalled and used in accordance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. RF Exposure This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equip- ment should be installed and operated with minimum distance 20cm between the radiator and your body. This trans- mitter must not be co-located or operating in conjunction with any other antenna or transmitter. INDUSTRY CANADA This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ- ing interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'uti- lisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. RF Exposure Cet équipement est conforme aux limites ďexposition aux radiations dans un environnement noncontrôlé. Cet équipement doit être installé et utilisé à distance minimum de 20cm entre le radiateur et votre corps. Cet émetteur ne doit pas être co-localisées ou opérant en conjunction avec tout autre antenne ou transmetteur. 2 7 REVISION 1.1 07DEC15 REVISION 1.1 07DEC15 ZigBee Hardwired Roller Shade System Overview Power Supply: 24 VDC, 7.5A RJ-45 Ports for Motorized Shades and Switches - Quantity 8 Communication Ports (RJ-45) - Quantity 2 Part # Part # ZigBee Hardwired Roller Shade Third Party Integration Wire Specification:  Category 5e/Category 6 for use with RJ-45 Connector  24 AWG  Maximum length of wire from Power Distribution Panel to device : - 8’ X 8’ Shade with 40:1 motor - 1250’ - 12’ X 12’ Shade with 73:1 motor - 750’ - 12’ X 20’ Shade with 73:1 motor - 500’ - Hardwired 4 and 8 Button Switches - 1000’ *Length based on 115K baud rate  Maximum wire length for RS485 communication - 2000’ Power Distribution Panel:  8 RJ-45 ports for motorized shades and switches  2 additional RJ-45 communication ports dedicated to daisy chain with other Power Distribution Panels and Third Party Integration via RS485.  Power Supply - AC Input: 100-240 VAC, 2.5A - DC Output: 24 VDC, 7.5A Note:  Standard Roll Applications (Motor Left) - Wire will need to be run to the LEFT side of the window (as shown).  Reverse Roll Applications (Motor Right) - Wire will need to be run to the RIGHT side of the window . Power Distribution Panels 24 VDC Power Supplies RS485 Communication Third Party Integration System Capacity:  200 Devices (QMotion Shades, QMotion Wireless Remotes, QMotion Hardwired Switches and other ZigBee devices) *Specifications are subject to change without notice 6 3 REVISION 1.1 07DEC15 REVISION 1.1 07DEC15 Wire Specification:  Category 5e/Category 6 for use with RJ-45 Connector  24 AWG  Maximum length of wire from Power Distribution Panel to device: - 8’ X 8’ Shade with 40:1 motor - 1250’ - 12’ X 12’ Shade with 73:1 motor - 750’ - 12’ X 20’ Shade with 73:1 motor - 500’ - Hardwired 4 and 8 Button Switches - 1000’ *Length based on 115K baud rate  Maximum wire length for RS485 communication - 2000’ Power Distribution Panel:  8 RJ-45 ports for motorized shades and switches  2 additional RJ-45 communication ports dedicated to daisy chain with other Power Distribution Panels and Third Party Integration via RS485.  Power Supply - AC Input: 100-240 VAC, 2.5A - DC Output: 24 VDC, 7.5A Note:  Standard Roll Applications (Motor Left) - Wire will need to be run to the LEFT side of the window (as shown).  Reverse Roll Applications (Motor Right) - Wire will need to be run to the RIGHT side of the window . ZigBee Hardwired Roller Shade Single Hardwired Switch Application Part # Part # 24 VDC Power Supply Power Distribution Panel Hardwired Switch ZigBee Hardwired Roller Shade Third Party Integration 24 VDC Power Supplies 24 VDC Power Supplies Hardwired…

Text truncated - open the document above for the full version.

Cover Letter(s)

December 9, 2015 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: I hereby appoint Sam Wismer at Advanced Compliance Solutions, Inc. to act as our agent in the preparation of an application for equipment authorization of FCC ID:2ABLX-150562Zto the FCC Rules and Regulations. I certify that all exhibits contained within this filing properly describe the device or system for which authorization is sought. I further certify that appropriate arrangements have been made to assure that production units of this equipment bearing the name and FCC IDENTIFIER listed in this application will continue to comply with the Commission's requirements. I further certify by signature below that no party (per 47 CFR 1.2002(b)) to the application is subject to a denial of Federal benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). This appointment also includes the authority to complete FCC Form 731 on our behalf and sign the application as an authorized agent. Sincerely, David Ayer RF Design Engineer

Cover Letter(s)

CONFIDENTIALITY REQUEST QM150562Z2ABLX-150562Z QM150562Z

Cover Letter(s)

5015 B. U. Bowman Dr. Buford, GA 30518 December 10, 2015 ACS TCB 5015 B.U. Bowman Drive Buford, GA 30518 Re: FCC ID: 2ABLX-150562Z To Whom It May Concern: The following application is submitted on behalf of our client, Qmotion Incorporated, for evaluation of their model QM150562Z for certification under FCC Part 15.247. The QM150562Z 2-Channel wired/wireless Ethernet switch contains a 2.4GHz direct sequence spread spectrum ZigBee radio and is powered through Ethernet Cat5e cable. The QM150562Z can control ZigBee shades either by wireless connectivity or by wired Ethernet ES-485 communications. The QM150562Z was tested in full to the requirements of the aforementioned rules and was found to be in compliance. Sincerely, Sam Wismer Vice President, Technology Advanced Compliance Solutions, Inc.

External Photos

ID Label/Location Info

Internal Photos

RF Exposure Info

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Certification Exhibit FCC ID: 2ABLX-150562Z FCC Rule Part: 15.247 ACS Project Number: 15-0413 Manufacturer: Qmotion Incorporated Model: QM150562Z Model: QM150562ZFCC ID: 2ABLX-150562Z ACS Project: 15-0413Advanced Compliance SolutionsPage 2 General Information: Applicant:Qmotion Incorporated Device Category:Mobile Environment:General Population/Uncontrolled Exposure Technical Information: Antenna Type: Inverted Meandering F-Antenna Antenna Gain: 3.3dBi Maximum Transmitter Conducted Power: -2.07 dBm, 0.62 mW Maximum System EIRP: 1.23 dBm, 1.33 mW Exposure Conditions: Greater than 20 centimeters MPE Calculation The Power Density (mW/cm 2 ) is calculated as follows: S = 2 4R PG  Where: S = power density (in appropriate units, e.g. mW/cm2) P = power input to the antenna (in appropriate units, e.g., mW) G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna (appropriate units, e.g., cm) MPE Calculator for Mobile Equipment Limits for General Population/Uncontrolled Exposure* 2405-2.071.000.623.32.138 200.0003 Power Density (mW/cm^2) Distance (cm) Transmit Frequency (MHz) Radio Power (dBm) Power Density Limit (mW/Cm2) Radio Power (mW) Antenna Gain (dBi) Antenna Gain (mW eq.)

Test Report

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 7708318048 Fax: 7708318598 Certification Test Report FCC ID: 2ABLX150562Z IC: 8832A150562Z FCC Rule Part: 15.247 IC Radio Standards Specification: RSS247 ACS Report Number: 150413.W06.2A Manufacturer: Qmotion Incorporated Model: QM150562Z Test Begin Date: October 1, 2015 Test End Date: October 2, 2015 Report Issue Date: January 7, 2016 FOR THE SCOPE OF ACCREDITATION UNDER LAB Code 2006120 This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. Reviewed by: Kirby Munroe Director, Wireless Certifications ACS, Inc. This test report shall not be reproduced except in full. This report may be reproduced in part with prior written consent of ACS, Inc. The results contained in this report are representative of the sample(s) submitted for evaluation. This report contains 20 pages 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 7708318048 Fax: 7708318598 TABLE OF CONTENTS 1 GENERAL ............................................................................................................................................ 3 1.1 PURPOSE .......................................................................................................................................... 3 1.2 PRODUCT DESCRIPTION ................................................................................................................... 3 1.3 TEST METHODOLOGY AND CONSIDERATIONS ................................................................................. 4 2 TEST FACILITIES .............................................................................................................................. 5 2.1 LOCATION ....................................................................................................................................... 5 2.2 LABORATORY ACCREDITATIONS/RECOGNITIONS/CERTIFICATIONS ................................................ 5 2.3 RADIATED EMISSIONS TEST SITE DESCRIPTION .............................................................................. 6 2.3.1 Semi-Anechoic Chamber Test Site .......................................................................................... 6 2.3.2 Open Area Tests Site (OATS) ................................................................................................. 7 2.4 CONDUCTED EMISSIONS TEST SITE DESCRIPTION ........................................................................... 8 3 APPLICABLE STANDARD REFERENCES .................................................................................... 8 4 LIST OF TEST EQUIPMENT ............................................................................................................ 9 5 SUPPORT EQUIPMENT ...................................................................................................................10 6 EQUIPMENT UNDER TEST SETUP BLOCK DIAGRAM ..........................................................10 7 SUMMARY OF TESTS ......................................................................................................................11 7.1 ANTENNA REQUIREMENT – FCC 15.203 ........................................................................................11 7.2 POWER LINE CONDUCTED EMISSIONS – FCC 15.207, IC: RSS-GEN 8.8 ........................................11 7.2.1 Measurement Procedure ........................................................................................................11 7.2.2 Measurement Results .............................................................................................................11 7.3 6DB / 99% BANDWIDTH – FCC 15.247(A)(2), IC: RSS-247 5.2(1) ................................................12 7.3.1 Measurement Procedure ........................................................................................................12 7.3.2 Measurement Results .............................................................................................................12 7.4 FUNDAMENTAL EMISSION OUTPUT POWER – FCC 15.247(B)(3), IC: RSS-247 5.4(4) ...................14 7.4.1 Measurement Procedure ........................................................................................................14 7.4.2 Measurement Results .............................................................................................................14 7.5 EMISSION LEVELS – FCC 15.247(D), 15.205, 15.209; IC RSS-247 5.5, RSS-GEN 8.9....................15 7.5.1 Emissions into Non-restricted Frequency Bands ...................................................................15 7.5.1.1 Measurement Procedure ................................................................................................................... 15 7.5.1.2 Measurement Results ....................................................................................................................... 15 7.5.2 Emissions into Restricted Frequency Bands - FCC 15.205, 15.209; RSS-Gen 8.9/8.10 .......17 7.5.2.1 Measurement Procedure ................................................................................................................... 17 7.5.2.2 Duty Cycle Correction ..................................................................................................................... 17 7.5.2.3 Measurement Results ....................................................................................................................... 17 7.5.2.4 Sample Calculation: ......................................................................................................................... 18 7.6 MAXIMUM POWER SPECTRAL DENSITY IN THE FUNDAMENTAL EMISSION – FCC 15.247(E) IC: RSS-247 5.2(2) ..........................................................................................................................................19 7.6.1 Measurement Procedure ................................................................…

Text truncated - open the document above for the full version.

Test Setup Photos

Contact Information

Applicant

David Ayer(RF Design Engineer)

[email protected]850-308-7328Fax: 850-208-3404

Test Firm

TUV SUD America, Inc.Sam Wismer

[email protected]678-341-5924Fax: 678-341-5924

Technical Specifications

#	Rule Parts	Frequency Range	Power Output
1	15C	2.40 GHz - 2.48 GHz	600.00 µW

Confidentiality

Long Term

Grant Notes

Power listed is conducted. This device must be installed to provide a separation distance of at least 20 cm from all persons. Users must be provided with device operating conditions for satisfying RF exposure compliance. Device must operate with a source-based, time-averaged duty cycle not to exceed 66% controlled via software or firmware.