2ABZJ-100-0003611 GHz Backhaul Radio

B11User Guide Warnings, Warranty, Compliance & Regulatory Statements Export Control These commodities, technology, or software were exported from the United States in accordance with the Export Administration Regulations. Diversion contrary to U.S. law is prohibited. Important Safety and Handling Information Failure to follow any of the safety instructions in this guide, instructions on any Mimosa provided packaging, and heed WARNINGS (indicated by ), could result in fire, electric shock or other injury, and incur damage to this product or other property and voiding of the product Limited Warranty. There are no End User serviceable parts inside the equipment. Read all operating and safety instructions contained herein and accompanying the product as provided by Mimosa Networks, Inc. (“Mimosa”) Occupational/controlled exposure limits apply when using the equipment. Persons exposed as a consequence of their employment should use appropriate means to mitigate their RF exposure. Electrical Safety Information Do not operate this product in any location that can be submerged by water. Do not install or maintain this product during the presence of an electrical storm to avoid risk of electric shock from lightning. Power specifications are indicated on the power supply provided with the Mimosa product. Connecting to any power source that does not meet the voltage, frequency and current requirements listed may damage the power supply or product, and pose a fire hazard. Depending on the product model, your product will be classified either as a safety class I or safety class II compliant device. Class I devices require a connection to earth ground (3-terminal plug), while class II devices incorporate a 2- terminal plug Class I: This device is intended for use with a grounded safety outlet. A safety ground wire (3-wire outlet plug type) is included on the provided AC adapter. Under no circumstances should you replace the provided detachable power cord with a non-grounded (2-wire outlet plug type) or use any adapter plugs which do not provide ground wire continuity. Class II: Safety Class II-compliant devices include supplemental insulation to protect against electric shock, and do not require a connection to earth ground. Installation of the product must comply with local and national electrical codes. Mandatory Grounding Instructions IMPORTANT: In order to comply with the Mimosa Limited Warranty conditions in this document, you must properly ground the device according to these instructions. Failure to properly ground the device will violate the product warranty. A minimum grounding wire of 10 AWG (5.26 mm 2 ) with a secured grounding terminal, and shorter in length than 1 meter is required. It is NOT supplied with the product. 1. Ensure that NO power is being supplied to the product. 2. Locate the Ground point screw next to the Ground icon on the device 3. Remove the provided Ground Screw 4. Thread the ground wire terminal and ground wire meeting the above specifications over the screw removed in the previous step. 5. Replace and tighten the screw with the threaded ground terminal and cable at the product Ground point. 6. Secure the other end of the grounding cable to the properly grounded structure (pole, tower, mast, etc.) meeting local and national electrical regulations and codes. End User Product Warranty Products purchased from Mimosa Networks, Inc. (“Mimosa”) are warranted against defects in material, and workmanship for a period of either (i) twelve (12) months from the date of activation, or (ii) thirty-six (36) months from the original date of shipment, whichever is earlier. Please go to www.mimosa.co/warranty to determine whether your product is in warranty. The sole responsibility of Mimosa under this warranty shall be limited to the repair or replacement of in-warranty defective product, at Mimosa’s sole option. Out of warranty products shipped to Mimosa will not be returned. This warranty does not cover costs associated with the removal and/or reinstallation of the product for repair nor for any parts that are readily replaced in normal use. Mimosa or its designated partner will repair or replace product found to be defective during the defined warranty period. The End User is responsible for delivering defective product in accordance with Mimosa’s published Return Material Authorization (RMA) processes. Limitation of Warranty Mimosa’s product warranty is invalidated if the RMA product is altered or otherwise tampered with in a manner that modifies the product from its original shipping configuration and/or form factor, and could violate the End User’s authority to operate the equipment, unless said activity was performed by or with the written authorization of a Mimosa representative. Modifications include: (a) External surfaces that have been painted, labeled, or otherwise modified from the original shipping condition. (b) Modifications of the product with third party hardware, firmware, and/or software. (c) Any product subjected to abnormal physical or electric stress, including, but not limited to, lightning strikes, negligence, accident, or misuse. (d) Any product damaged due to incorrect installation, including, but not limited to, improper product mounting, cabling, cabling defects or connection to power. (e) Failure induced by connected third party products. Improper grounding, or failure to ground the product as instructed in this guide will void the End User warranty. Mimosa will not warrant any product which has been installed outdoors without the use of minimum CAT 6 shielded Ethernet cable and/or proper earth grounding. Disclaimer EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, MIMOSA NETWORKS AND ITS SUBSIDIARIES, LICENSORS AND AFFILIATES ( COLLECTIVELY, “MIMOSA”), AND ANY THIRD PARTY DATA, SERVICE, SOFTWARE AND HARDWARE PROVIDERS MAKE NO OTH- ER REPRESENTATION OR WARRANTY OF ANY KIND AND HEREBY DISCLAIM ALL WAR- RANTIES, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, …

Text truncated - open the document above for the full version.

B11 Product Label WEIGHT: B SHEET 1 OF 1 SCALE:1:1DWG NO. TITLE: REVISION DO NOT SCALE DRAWING MATERIAL: DATE SIGNATURE NAME FINISH: High gloss coated ADHESIVE: 3M 8153LE MATERIAL: 10mil (.010 inch) GE HP92X LEXAN (UV protected weatherable) UNLESS OTHERWISE SPECIFIED:DIMENSIONS ARE IN MILLIMETERSSURFACE FINISH:TOLERANCES: LINEAR: ANGULAR: Q.A MFG APPV'D CHK'D DRAWN JAIME FINK 615-00039 54.00 2.126 50.00 1.968 R3.00 .118 11.63 5.00 FCC ID 2ABZJ-100-00036 Contains FCC ID: PPD-AR5B125 Model: B11 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. B11 Backhaul Grey print text color: Process Black 77 c0 m0 y0 k77 Background label color: MATCHED to MIMOSA WHITE SAMPLE PROVIDED BLUE rectangular area with 1.2mm radius rounded corners represents a transparency area NO GLUE ON RECTANGULAR TRANSPARENCY AREA Orange is PANTONE 1375 C

Label goes here

Company: Mimosa Networks Test of: B11 Microwave Fixed Link To: FCC CFR 47 Part 101 Report No.: MIMO04-U3 MPE Rev A MPE TEST REPORT MPE TEST REPORT FROM Test of: Mimosa Networks B11 Microwave Fixed Link to To: FCC CFR 47 Part 101 Test Report Serial No.: MIMO04-U3 MPE Rev A This report supersedes: NONE Applicant: Mimosa Networks 469 El Camino Real, Suite 100 Santa Clara, California 95050 USA Product Function: Microwave Fixed Link Issue Date: 5 th November 2015 This Test Report is Issued Under the Authority of: MiCOM Labs, Inc. 575 Boulder Court Pleasanton California 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com MiCOM Labs is an ISO 17025 Accredited Testing Laboratory Title: Mimosa Networks B11 Microwave Fixed Link To: FCC CFR 47 Part 101 Serial #: MIMO04-U3 MPE Rev A Issue Date: 5 th November 2015 Page: 3 of 4 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. All changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: +1 (925) 462 0304, Fax: +1 (925) 462 0306, www.micomlabs.com 1. MAXIMUM PERMISSABLE EXPOSURE Maximum Permissible Exposure FCC, Part 101 Calculations for Maximum Permissible Exposure Levels Power Density = Pd (mW/cm2) = EIRP/(4d 2 ) EIRP = P * G P = Peak output power (mW) G = Antenna numeric gain (numeric) d = Separation distance (cm) Numeric Gain = 10 ^ (G (dBi)/10) The Mimosa B11 Microwave Fixed Link calculations are based on a worst case scenario. The Mimosa B 11 is a professionally installed device. Maximum Antenna Gain = 50.0 dBi (Numeric 100,000) Maximum Conducted Power Measured (40 MHz, Channel 11,225 MHz) = +27.56 dBm The EUT belongs to the Controlled Exposure the limit of power density is 5.0 mW/cm 2 Distance (cm) Freq. Band (MHz) Antenna Gain (dBi) Effective Numeric Gain (numeric) Max Peak Output Power (dBm) Max Peak Output Power (mW) Peak Output Power (mW/EIRP) Calculated Safe Distance @ 5mW/cm 2 Limit(cm) Minimum Separation Distance (cm) 11225.0 50.0 100,000 27.56 570.2 57,020,000 952.6 952.6 Note: for mobile or fixed location transmitters the minimum separation distance is 20cm, even if calculations indicate the MPE distance to be less. Specification Maximum Permissible Exposure Limits Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency levels in excess of the Commission’s guidelines. See §1.1310 of this chapter. Limit = 5 mW / cm 2 from 1.310 Table 1, (A) Limits for Occupational/Controlled Exposure Laboratory Measurement Uncertainty for Power Measurements Measurement uncertainty 1.33dB 575 Boulder Court Pleasanton, California 94566, USA Tel: +1 (925) 462 0304 Fax: +1 (925) 462 0306 www.micomlabs.com

COVER PAGE Test of Mimosa Networks To: FCC 47 CFR Part 101 Test Report Serial No.: MIMO04-U3 Rev A This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. Any changes will be noted in the Document History section of the report. MiCOM Labs is an ISO 17025 Accredited Testing Laboratory TITLE PAGE TEST REPORT FROM Test of Mimosa Networks to To FCC 47 CFR Part 101 Test Report Serial No.: MIMO04-U3 Rev A This report supersedes NONE Applicant: Mimosa Networks 469 El Camino Real, Suite 100 Santa Clara, California 95050 USA Product Function: Microwave Fixed Link Copy No: pdf Issue Date: 9th November 2015 This Test Report is Issued Under the Authority of; MiCOM Labs, Inc. 575 Boulder Court, Pleasanton, CA 94566 USA Phone: +1 (925) 462-0304 Fax: +1 (925) 462-0306 www.micomlabs.com TESTING CERT #2381.01 Title: To: Serial #: Issue Date: Page: Mimosa Networks - B11 FCC 47 CFR Part 101 MIMO04-U3 Rev A 9th November 2015 3 of 119 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. Any changes will be noted in the Document History section of the report. MiCOM Labs, 575 Boulder Court, Pleasanton, CA 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com This page has been left intentionally blank Title: To: Serial #: Issue Date: Page: Mimosa Networks – B11 FCC 47 CFR Part 101 MIMO04-U3 Rev A 9th November 2015 4 of 119 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. Any changes will be noted in the Document History section of the report. M iCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com TABLE OF CONTENTS ACCREDITATION, LISTINGS & RECOGNITION ............................................................ 5 ACCREDITATION - TESTING ......................................................................................... 5 RECOGNITION ................................................................................................................ 6 PRODUCT CERTIFICATION ........................................................................................... 7 1. TEST RESULT SUMMARY ....................................................................................... 9 2. REFERENCES AND MEASUREMENT UNCERTAINTY ....................................... 10 2.1. Normative References ........................................................................................... 10 2.2. Test and Uncertainty Procedures .......................................................................... 11 3. PRODUCT DETAILS AND TEST CONFIGURATIONS .......................................... 12 3.1. Technical Details ................................................................................................... 12 3.2. Scope of Test Program .......................................................................................... 13 3.3. Equipment Model(s) and Serial Number(s) ............................................................ 17 3.4. Antenna Details ..................................................................................................... 17 3.5. Cabling and I/O Ports ............................................................................................ 17 3.6. Test Configurations ............................................................................................... 18 3.7. Equipment Modifications ........................................................................................ 18 3.8. Deviations from the Test Standard ........................................................................ 18 4. TESTING EQUIPMENT CONFIGURATION(S) ....................................................... 19 4.1. Conducted RF Emission Test Set-up ..................................................................... 19 4.2. Radiated Spurious Emission Test Set-up .............................................................. 21 5. TEST SUMMARY ..................................................................................................... 23 6. T EST RESULTS ...................................................................................................... 24 6.1. Device Characteristics ........................................................................................... 24 6.1.1. Conducted Testing ................................................................................... 24 6.1.2. Radiated Testing .................................................................................... 117 Title: To: Serial #: Issue Date: Page: Mimosa Networks – B11 FCC 47 CFR Part 101 MIMO04-U3 Rev A 9th November 2015 5 of 119 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. Any changes will be noted in the Document History section of the report. M iCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com ACCREDITATION, LISTINGS & RECOGNITION ACCREDITATION - TESTING MiCOM Labs, Inc. is an accredited Electrical testing laboratory per the international standard ISO/IEC 17025. The company is accredited by the American Association for Laboratory Accreditation (A2LA) www.a2la.org test laboratory number 2381.01. MiCOM Labs test schedule is available at the following URL; http://www.a2la.org/scopepdf/2381-01.pdf Title: To: Serial #: Issue Date: Page: Mimosa Networks – B11 FCC 47 CFR Part 101 MIMO04-U3 Rev A 9th November 2015 6 of 119 This test report may be reproduced in full only. The document may only be updated by MiCOM Labs personnel. Any changes will be noted in the Document History section of the report. M iCOM Labs, 575 Boulder Court, Pleasanton, California 94566 USA, Phone: 925.462.0304, Fax: 925.462.0306, www.micomlabs.com RECOGNITION MiCOM Labs, Inc has widely recognized Electrical testing capabilities. Our international recognition …

Text truncated - open the document above for the full version.

MiCOM Labs, 575 Boulder Court, Pleasanton, CA 94566 Tel: +1 (925) 462-0304, Fax: +1 (925) 462-0306, Web: www.micomlabs.com 10 November 2015 Mimosa Networks Test Setup Photographs Conducted Page 2 of 4 the wireless lab AC Wireline Page 3 of 4 the wireless lab Digital Emissions <1GHz Page 4 of 4 the wireless lab RF Conducted