2ACMLPN41734Condeco 4.3 inch Touch Screen

Condeco User Manual for 4.3” Screen This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The RF ID belongs to category 3 receiver, and the dutyclycle is less than 10% The RF ID could be supplied by DC 5V from adapter,which input AC 120V/60Hz, output DC 5V/1A adapter. also could be supplied by DC 48V from POE adapter, which input 120V/60Hz, output DC 48V POE Operating ambient temperature range:-20 to 40 Page 2 of 7 Condeco Hardware Section Contents User manual ........................................................................................................................ 4 Equipments required: ..................................................................................................... 4 Prepare to power up 4.3” screen: .................................................................................... 4 Book a desk with 4.3” screen ........................................................................................... 5 About .................................................................................................................................. 8 Condeco Room Booking ................................................................................................. 8 About Condeco ............................................................................................................... 8 Who we work with .......................................................................................................... 8 Contact ............................................................................................................................... 9 Page 3 of Condeco Hardware Section Responsibility Name Owner Condeco Ltd Author(s) Reviewer Approver Phil Briffa Version Status Reason for change Date 1.0 Final Initial Release 27 May 2014 Name Organisation Project Number 7 Page 4 of Condeco Hardware Section User Manual for 4.3” screen Equipments required: 1. A standard POE (48V) network connection. 2. A network cable. Prepare to power up the 4.3” screen: 1. Prepare the POE network cable and fine the RJ45 network connector on the back of the 4.3” scree. 2. Plug the network cable into the RJ45 connector to power the screen up. 7 Page 5 of Condeco Hardware Section 3. Display comes up with Condeco logo. Screen powered up. Book a desk with Condeco 4.3” screen The following formats of RFID cards are fully compatible with Condeco 4.3” screen: HID Prox, HID iClass, Mifare, Desfire. 1. Following with Condeco logo, the booking screen will comes up in 2-3 second. 7 Page 6 of Condeco Hardware Section 2. On the touch screen, key in the desk ID then press the Save button. 3. After press Save, the desk ID will appear on the screen. Press Book Now to book the desk. 4. Key in the security code or swipe the RFID card in front of the screen. 7 Page 7 of 7 Condeco Hardware Section 5. Desk has been booked. The person’s name will display on the screen until the time is expired. 6. If you want to canecl the booking, press Release button. Then key in the security code or swipe the RFID card in front of the screen. The booking will be cancel.

Condeco Ltd Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Request for Confidentiality Company name: Condeco Ltd FCC ID : 2ACMLPN41734 FCC Part 15 Certification Gentlemen, Pursuant to 47 CFR 0.457(d)(1)(ii) and 0.459 we hereby requests permanent confidentiality of the following documents for the subject application: Exhibit Type Description ☒ Schematics All circuitry of devices and component values ☒ Block Diagrams Details of device showing the frequency of all oscillators ☒ Operational Description Description of the circuit functions Note: Exhibit types that are commonly held confidential are: (1) Schematics, (2) Block Diagrams, (3) Bill Of Materials, (4) Operational Descriptions. Any exhibit NOT granted confidentiality is viewable on the FCC website as soon as a grant is issued. These documents contain detailed system and equipment description and related information about the product which we considers to be proprietary, confidential and a custom design and otherwise would not release to the general public. Since the design is a basis from which future technological products will evolve, we consider that this information would be of benefit to its competitors and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Yours sincerely, Signatory Name Philip Briffa Position Technical Director Company Name Condeco Ltd Address 8th Floor, Exchange Tower, 2 Harbour Exchange Square, London E14 9GE, UK Tel +44 (0)207 0012028 Fax +44 (0)207 0012030 Email [email protected]

Condeco Ltd Date: 26.06.2014 Authority to Act as an Agent We declare that the following representative (agent) Name Mark Zhu Position Manager Company Name Shenzhen Certification Technology Service Co., Ltd. Address 2F, Building B, East Area of Nanchang Second Industrial Zone, Gushu 2 nd Road, Bao’an District, Shenzhen 518126, P.R. China Tel / Fax 0755-86375541/0755-26736857 Email [email protected] to act on our behalf on all matters concerning the application and documents submitted to PHOENIX TEST-LAB for product certification below Product Name Condeco 4.3” Touch Screen Model Name PN41734 Brand Name Condeco . Yours sincerely, Signatory Name Philip Briffa Position Technical Director Company Name Condeco Ltd Address 8th Floor, Exchange Tower, 2 Harbour Exchange Square, London E14 9GE, UK Tel +44 (0)207 0012028 Fax +44 (0)207 0012030 Email [email protected] In case of FCC, we certify that we are not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance.

External photo of EUT

Label and location

Internal photo of EUT Antenna

Shenzhen Certification Technology Service Co., Ltd. 2F, Building B, East Area of Nanchang Second Industrial Zone, Gushu 2 nd Road, Bao'an District, Shenzhen 518126, P.R. China FCC ID: 2ACMLPN41734 Page 1 of 31 TEST REPORT FCC ID: 2ACMLPN41734 Applicant : Condeco Ltd Address : 8th Floor, Exchange Tower, 2 Harbour Exchange Square, London E14 9GE, UK Equipment Under Test (EUT): Name : Condeco 4.3” Touch Screen Model : PN41734 In Accordance with: FCC CFR47 Part 15 Section 15C: 2013 Report No : CST-TCB140609023 Date of Test : June 16, 2014 to June 24, 2014 Date of Issue : June 24, 2014 Test Result: PASS In the configuration tested, the EUT complied with the standards specified above Authorized Signature ___________________________ (Mark Zhu) General Manager The manufacture should ensure that all the products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of Shenzhen Certification Technology Service Co., Ltd. Or test done by Shenzhen Certification Technology Service Co., Ltd. Approvals in connection with, distribution or use of the product described in this report must be approved by Shenzhen Certification Technology Service Co., Ltd. Approvals in writing. Report No.: CST-TCB140609023 FCC ID: 2ACMLPN41734 Page 2 of 31 Contents 1. General Information ...............................................................................................................3 1.1. Description of Device (EUT) ..........................................................................................3 1.2. Accessories of device (EUT) ..........................................................................................3 1.3. Test Lab information .......................................................................................................3 2. Summary of test ......................................................................................................................4 2.1. Summary of test result ....................................................................................................4 2.2. Assistant equipment used for test....................................................................................4 2.3. Block Diagram ................................................................................................................4 2.4. Test mode ........................................................................................................................4 2.5. Test Conditions ...............................................................................................................4 2.6. Measurement Uncertainty (95% confidence levels, k=2) ...............................................5 2.7. Test Equipment ...............................................................................................................6 3. 20dB bandwidth ......................................................................................................................7 3.1. Limit................................................................................................................................7 3.2. Test Procedure.................................................................................................................7 3.3. Test Setup ........................................................................................................................7 3.4. Test Result.......................................................................................................................7 4. Radiated emissions..................................................................................................................8 4.1. Limit(FCC 15.209)..........................................................................................................8 4.2. Block Diagram of Test setup ...........................................................................................8 4.3. Test Procedure.................................................................................................................9 4.4. Test Result.....................................................................................................................10 4.5. Field strength.................................................................................................................13 4.6. Emissions Result of Inside band (13.56MHZ)..............................................................14 5. Frequency stability................................................................................................................16 5.1. Test limit .......................................................................................................................16 5.2. Test Procedure...............................................................................................................16 5.3. Test Setup ......................................................................................................................16 5.4. Test Results ...................................................................................................................16 6. Power Line Conducted Emissions .......................................................................................18 6.1. Block Diagram of Test Setup ........................................................................................18 6.2. Limit..............................................................................................................................18 6.3. Test Procedure...............................................................................................................18 6.4. Test Result.....................................................................................................................19 7. Antenna Requirements .............…

Text truncated - open the document above for the full version.

Test setup photo 1.1. Photographs-Radiated Emission Test Setup in Chamber Below 30M Below 30M-1G 1.2. Photographs-Conducted Emission Test Setup