2ACMLPN41827Condeco 10.1 inch Touch Screen

Condeco User Manual for 10.1” Screen NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. The RF ID belongs to category 3 receiver, and the dutyclycle is less than 10% The RF ID could be supplied by DC 12V from adapter,which input AC 120V/60Hz, output DC 12V/170.8mA adapter. also could be supplied by DC 48V from POE adapter, which input 120V/60Hz, output DC 48V/170.8mA POE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Operating ambient temperature range:-20 to 40 Page 2 of 9 Condeco Hardware Section Contents User manual ........................................................................................................................ 4 Equipments required: ..................................................................................................... 4 Start with 10.1” screen: ................................................................................................... 4 Book a meeting room with 10.1” screen .......................................................................... 5 Start the meeting ........................................................................................................... 7 About .................................................................................................................................. 9 Condeco Room Booking ................................................................................................. 9 About Condeco ............................................................................................................... 9 Who we work with .......................................................................................................... 9 Contact ............................................................................................................................. 10 Page 3 of 9 Condeco Hardware Section Responsibility Name Owner Condeco Ltd Author(s) Reviewer Approver Phil Briffa Version Status Reason for change Date 1.0 Final Initial Release 03 Jun 2014 Name Organisation Project Number Page 4 of 9 Condeco Hardware Section User Manual for 10.1” screen Equipments required: 1. A standard POE (48V) network connection. 2. A network cable. Start with 10.1” screen: Connect the POE network cable to RJ45 connector at the back of the screen to power it up. Page 5 of 9 Condeco Hardware Section To book a meeting room: 1. Once it has powered on, the Resource ID screen will comes up. Key in the Resource ID on the touch screen and then press Confirm button. 2. Press the time display on the screen to choose when you want to use the meeting room. Page 6 of 9 Condeco Hardware Section 3. The time you have chosen will be highlighted in yellow. Press Confirm button. 4. Swipe the RFID card at bottom centre of the display panel, or key in the pin on the touch screen to book the meeting room. Page 7 of 9 Condeco Hardware Section 5. Once it has been successfully booked, the time bar on the screen will become red. To Start the Meeting: 1. Press Start on the touch screen. Page 8 of 9 Condeco Hardware Section 2. Enter pin or swipe the RFID card on the screen to start the meeting. 3. If you have finished using meeting room before the time run out, you can end the meeting to free the room by press End button on the screen. Page 9 of 9 Condeco Hardware Section About Condeco Room Booking Condeco Meeting Room Booking software helps you to maximise your meeting room space, reduce admin time and introduce smarter booking processes into your workplace. Key features include Hospitality and Resource Management as well as Video Conference booking. We also offer interactive room signage and Mobile Room Booking. About Condeco We are the leading provider of meeting room and desk booking solutions, as well as advanced digital signage solutions. Our robust software and exceptionally designed hardware is the most feature-rich and versatile on the market. It powers your business to change the way you work and manage your real estate more effectively. Our complementary product suite and service delivery means, we spare you the headache of having to manage multiple vendors. Our vertically integrated departments encompass R+D and design − leading the way in software and hardware innovations – through to delivery, support and upgrade. Who we work with Today, we work with around 400 companies worldwide, including over 30% of the FTSE 100. We have offices in the UK, USA and India, as well as strategic partners in Australia, South Africa, Italy, Spain and Switzerland. Our strategic partners enable us to respond quickly to client demands with 24/7 …

Text truncated - open the document above for the full version.

Condeco Ltd Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Request for Confidentiality Company name: Condeco Ltd FCC ID : 2ACMLPN41827 FCC Part 15 Certification Gentlemen, Pursuant to 47 CFR 0.457(d)(1)(ii) and 0.459 we hereby requests permanent confidentiality of the following documents for the subject application: Exhibit Type Description ☒ Schematics All circuitry of devices and component values ☒ Block Diagrams Details of device showing the frequency of all oscillators ☒ Operational Description Description of the circuit functions Note: Exhibit types that are commonly held confidential are: (1) Schematics, (2) Block Diagrams, (3) Bill Of Materials, (4) Operational Descriptions. Any exhibit NOT granted confidentiality is viewable on the FCC website as soon as a grant is issued. These documents contain detailed system and equipment description and related information about the product which we considers to be proprietary, confidential and a custom design and otherwise would not release to the general public. Since the design is a basis from which future technological products will evolve, we consider that this information would be of benefit to its competitors and that the disclosure of the information in these documents would give competitors an unfair advantage in the market. Yours sincerely, Signatory Name Philip Briffa Position Technical Director Company Name Condeco Ltd Address 8th Floor, Exchange Tower, 2 Harbour Exchange Square, London E14 9GE, UK Tel +44 (0)207 0012028 Fax +44 (0)207 0012030 Email [email protected]

Condeco Ltd Date: 26.06.2014 Authority to Act as an Agent We declare that the following representative (agent) Name Mark Zhu Position Manager Company Name Shenzhen Certification Technology Service Co., Ltd. Address 2F, Building B, East Area of Nanchang Second Industrial Zone, Gushu 2 nd Road, Bao’an District, Shenzhen 518126, P.R. China Tel / Fax 0755-86375541/0755-26736857 Email [email protected] to act on our behalf on all matters concerning the application and documents submitted to PHOENIX TEST-LAB for product certification below Product Name Condeco 10.1” Touch Screen Model Name PN41827 Brand Name Condeco . Yours sincerely, Signatory Name Philip Briffa Position Technical Director Company Name Condeco Ltd Address 8th Floor, Exchange Tower, 2 Harbour Exchange Square, London E14 9GE, UK Tel +44 (0)207 0012028 Fax +44 (0)207 0012030 Email [email protected] In case of FCC, we certify that we are not subject to a denial of Federal benefits, that include FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. §862 because of a conviction for possession or distribution of a controlled substance.

External photo of EUT

Label and location

Internal photo of EUT Antenna

Shenzhen Certification Technology Service Co., Ltd. 2F, Building B, East Area of Nanchang Second Industrial Zone, Gushu 2 nd Road, Bao'an District, Shenzhen 518126, P.R. China FCC ID: 2ACMLPN41827 Page 1 of 32 TEST REPORT FCC ID: 2ACMLPN41827 Applicant : Condeco Ltd Address : 8th Floor, Exchange Tower, 2 Harbour Exchange Square, London E14 9GE, UK Equipment Under Test (EUT): Name : Condeco 10.1” Touch Screen Model : PN41827 In Accordance with: FCC CFR47 Part 15 Section 15C: 2013 Report No : CST-TCB140609024 Date of Test : June 16, 2014 to June 24, 2014 Date of Issue : June 24, 2014 Test Result: PASS In the configuration tested, the EUT complied with the standards specified above Authorized Signature ___________________________ (Mark Zhu) General Manager The manufacture should ensure that all the products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of Shenzhen Certification Technology Service Co., Ltd. Or test done by Shenzhen Certification Technology Service Co., Ltd. Approvals in connection with, distribution or use of the product described in this report must be approved by Shenzhen Certification Technology Service Co., Ltd. Approvals in writing. Report No.: CST-TCB140609024 FCC ID: 2ACMLPN41827 Page 2 of 32 Contents 1. General Information ...............................................................................................................3 1.1. Description of Device (EUT) ..........................................................................................3 1.2. Accessories of device (EUT) ..........................................................................................3 1.3. Test Lab information .......................................................................................................3 2. Summary of test ......................................................................................................................4 2.1. Summary of test result ....................................................................................................4 2.2. Assistant equipment used for test....................................................................................4 2.3. Block Diagram ................................................................................................................4 2.4. Test mode ........................................................................................................................4 2.5. Test Conditions ...............................................................................................................5 2.6. Measurement Uncertainty (95% confidence levels, k=2) ...............................................5 2.7. Test Equipment ...............................................................................................................6 3. 20dB bandwidth ......................................................................................................................7 3.1. Limit................................................................................................................................7 3.2. Test Procedure.................................................................................................................7 3.3. Test Setup ........................................................................................................................7 3.4. Test Result.......................................................................................................................7 4. Radiated emissions..................................................................................................................9 4.1. Limit(FCC 15.209)..........................................................................................................9 4.2. Block Diagram of Test setup ...........................................................................................9 4.3. Test Procedure...............................................................................................................10 4.4. Test Result..................................................................................................................... 11 5. Frequency stability................................................................................................................17 5.1. Test limit .......................................................................................................................17 5.2. Test Procedure...............................................................................................................17 5.3. Test Setup ......................................................................................................................17 5.4. Test Results ...................................................................................................................17 6. Power Line Conducted Emissions .......................................................................................19 6.1. Block Diagram of Test Setup ........................................................................................19 6.2. Limit..............................................................................................................................19 6.3. Test Procedure...............................................................................................................19 6.4. Test Result.....................................................................................................................20 7. Antenna Requirements .........................................................................................................22 7.1. Limit..............................................................................................................................22 7.2. Result …

Text truncated - open the document above for the full version.

Test setup photo 1.1. Photographs-Radiated Emission Test Setup in Chamber Below 30M Below 30M-1G 1.2. Photographs-Conducted Emission Test Setup