2ACYESK-60GTDD-A1Wireless Ethernet link

© ALL RIGHTS RESERVED TO SIKLU COMMUNICATION LTD. EtherHaul-600T™ Gigabit Ethernet Wireless Solution Installation Manual EH600-INST-03, Issue 2 August 2014 EH-600T Installation Manual Page 2 Trademarks Siklu, the Siklu logo, and EtherHaul are all trademarks of Siklu Communication Ltd. All other product names and trademarks mentioned in this document are trademarks or registered trademarks of their respective companies. Copyrights Copyright © 2014 Siklu Communication Ltd. All rights reserved. No part of this publication may be reproduced or distributed in any form or by any means, or stored in a database or retrieval system, without the prior written consent of Siklu. Disclaimers The information contained in this document is subject to change without notice. Siklu assumes no responsibility for any errors that may appear. Siklu makes no warranties, expressed or implied, by operation of law or otherwise, relating to this document, the products or the computer software programs described herein. This document was originally written in English. Please refer to the English language version for a full and accurate description of all products and services described herein. EH-600T Installation Manual Page 3 About this Document This document is the Installation Manual for the EtherHaul-600T wireless Link. It provides product overview and details the installation and initial setup. For instructions how to use the product’s features, refer to the “EtherHaul Operation, Administration and Maintenance Manual”. Note: Features and functionality described in this document may be available for specific product models or starting from specific SW version. Please review the individual product’s release notes to verify if a specific feature is supported in the product you use. Applicable Products and Releases  V-Band o EH-600T, minimum SW release 6.0.0 Audience This document assumes a working knowledge of wireless backhaul platforms and their operating environments. This document is intended for use by all persons who are involved in planning, installing, configuring, and using the EtherHaul system. Conventions The following conventions are used in this document in order to make locating, reading, and using information easier. Special Attention Hint: Informs you of a helpful optional activity that may be performed at the current operating stage. Note: Provides important and useful information or describes an activity or situation that may or will interrupt normal operation of the EtherHaul system, one of its components, or the network. EH-600T Installation Manual Page 4 Caution: Describes an activity or situation that requires special attention or warning. Text Conventions Document References Italicized text is used to reference sections or chapters in this document. In many cases, references use clickable hypertext links that enable immediate access to referenced objects. Command Input Monospace text is used to help delineate command line user input or text displayed in a command window. EH-600T Installation Manual Page 5 Safety and Regulatory Notices The following are mandatory notices for installation and operation of EtherHaul Wireless Backhaul Link. Indications appearing here are required by the designated government and regulatory agencies for purposes of safety and compliance. General Do not install or operate this System in the presence of flammable gases or fumes. Operating any electrical instrument in such an environment is a safety hazard. European Commission This product has been designed to comply with CE markings in accordance with the requirements of European Directive 1995/5/EC. This product has been designed to comply with the requirements of European Directives. This equipment must be permanently earthed for protection and functional purposes. To make a protective earth connection, use the grounding point located on the System ODU using a minimum amount of 16AWG grounding cable or according to local electrical code. This apparatus is intended to be accessible only to authorized personnel. Failure to prevent access by unauthorized personnel will invalidate any approval given to this apparatus. This product is in full compliance with the following standards:  RF EN 302 217-3 1.3.1 V-Band FCC Part 15.255  EMC EN 301 489-4  Safety IEC 60950  Operation EN 300 019-1-4 Class 4.1E  Storage EN 300 019-1-1 Class 1.2  Transportation EN 300 019-1-2 Class 2.2 FCC/IC Regulatory Statements This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and IC RSS standards. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference EH-600T Installation Manual Page 6 will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. Note: Changes or modifications to this equipment not expressly approved by Siklu LTD or the party responsible for compliance could void the user's authority to operate the equipment. Caution: Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government re…

Text truncated - open the document above for the full version.

FCC, Request for non-disclosure Date: 16-Jul-10 RF_501, Issue 6 Page 1 of 1 Company Name: Siklu Communication Ltd. Address : 43 HaSivim street City: Petach Tikva 49517 Country: Israel To: Telefication B.V., Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Request for confidentiality FCC ID: 2ACYESK-60GTDD-A1 Reference number: ###### Dear FCC TCB, 1. Long-Term Confidentiality Pursuant to 47 CFR Section 0.459(a) & (b), we hereby requests non-disclosure and confidential treatment of the following materials submitted in support of FCC certification application: Bill(s) of Material Block Diagrams Operational Description Schematic Diagrams Tune-up Procedure Above materials contain secrets, proprietary and technical information, which would customarily be guarded from competitors under 47 CFR, section 0.457(d)(2). Disclosure or publication or any portion of this company confidential material to other parties could cause substantial competitive harm and provide unjustified benefits for competitors. 2. Short-Term Confidentiality (STC) Pursuant to Public Notice DA 04-1705 of the Commission’s policy, in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, a pplicant hereby requests Short-Term Confidential treatment of the following materials (note 1): Internal Photos User’s Manual Test Set-up Photos External Photos Justification: The above information may assist competitors in understanding the system archtecture and major components, which may hurt our competitive advantage and help competitors with designing competing products Planned Release Date STC: March 1, 2015 (notes 2, 3, 4, 5) Date: August 17, 2014 Name and signature of applicant: Yaron Fein Notes: 1) A document or type of document can only have ONE type of confidentiality! 2) Short-Term confidentiality is in principle for 45 days from date of grant; it can be extended max 3 times (total time 180 days max.)! 3) FCC must be informed when marketing begins earlier. 4) Release takes place automatically thus extension must be requested in time. Telefication does not remind you of this! 5) Request for extension or for release must be received by Telefication at least 7 days before date of actual marketing or before expiration of the STC period

September 2, 2014 To: Telefication B.V. Attn: Dept. FCC TCB Edisonstraat 12A 6902 PK ZEVENAAR The Netherlands Subject: Application for certification of a point-to-point wireless Ethernet link operating in 57 – 64 GHz band, FCC ID:2ACYESK-60GTDD-A1 Dear Gentlemen, Please find attached our application for certification of a point-to-point wireless Ethernet link operating in 57 – 64 GHz band, FCC ID:2ACYESK-60GTDD-A1, prepared in accordance with FCC Rules, parts 2 and 15 section 15.255. The product testing and this application for certification were performed by Hermon Laboratories, which is listed by FCC (Registration Numbers 90623, 90624). The FCC Designation Number is US1003. Hermon Labs responsible person is Mr. Michael Nikishin, tel: 011 972 4626 8440, fax:011 972 4628 8277, e-mail: [email protected]. We hope this application satisfies your requirements. Please send an invoice to Hermon Labs. Sincerely, Yaron Fein, VP R&D Siklu Communication Ltd.

Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 1 of 4 EXTERNAL PHOTOGRAPHS This document contains 3 photographs Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 2 of 4 Photograph No.1 EtherHaul EH-600T top panel view Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 3 of 4 Photograph No.2 EtherHaul EH-600T front view Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 4 of 4 Photograph No.3 EtherHaul EH-600T side view

Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 1 of 1 LABEL The label is affixed on the top side of the radio unit as shown below. The label material is PVC with a permanent adhesive. EtherHaul EH-600T top panel, label with FCC ID:2ACYESK-60GTDD-A1 location

Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 1 of 7 INTERNAL PHOTOGRAPHS This document contains 6 photographs Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 2 of 7 Photograph No.1 EtherHaul EH-600T internal view Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 3 of 7 Photograph No.2 EtherHaul EH-600T Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 4 of 7 Photograph No.3 EtherHaul EH-600T Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 5 of 7 Photograph No.4 EtherHaul EH-600T RF card front view Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 6 of 7 Photograph No.5 EtherHaul EH-600T RF card second side view Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 7 of 7 Photograph No.6 EtherHaul EH-600T antenna

Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 1 of 1 Environmental evaluation and exposure limit according to FCC CFR 47part 1, §1.1307, §1.1310 The calculation was done to confirm required safe distance for fixed device. Limit for power density for general population/uncontrolled exposure is 1 mW/cm 2 for 1500 -100000 MHz frequency range: The power density P (mW/cm 2 ) = P T / 4 r 2 , where P T is the maximum equivalent isotropically radiated power (EIRP). The peak output power is 8.32 dBm and max antenna gain is 35 dBi, that corresponds to the equivalent isotropically radiated power (EIRP) of 8.32 dBm + 35 dBi = 43.32 dBm, which is equal to 21478 mW. The minimum safe distance “r”, where RF exposure does not exceed FCC permissible limit, is r = sqrt { P T / (Px4)} = sqrt {21478 / 12.56} = 41.4 cm. The information note about safe distance shall be provided in the User Manual.

Hermon Laboratories Ltd. Harakevet Industrial Zone, Binyamina 30500, Israel Tel. +972-4-6288001 Fax. +972-4-6288277 E-mail: [email protected] Page 1 of 113 Report ID: SIKRAD_FCC.25826_rev2.doc Date of Issue: 27-Aug-14 ELECTRICAL TESTING 0839.01 TEST REPORT ACCORDING TO: FCC 47 CFR part 15 section 15.255 FOR: Siklu Communication Ltd. Point-to-point wireless Ethernet link operating in 57-64 GHz Model: EtherHaul EH-600T FCC ID:2ACYESK-60GTDD-A1 This report is in conformity with ISO/ IEC 17025. The "A2LA Accredited" symbol endorsement applies only to the tests and calibrations that are listed in the scope of Hermon Laboratories accreditation. The test results relate only to the items tested. This test report shall not be reproduced in any form except in full with the written approval of Hermon Laboratories Ltd. Report ID: SIKRAD_FCC.25826_rev2.doc Date of Issue: 27-Aug-14 Page 2 of 113 Table of contents 1 Applicant information ..................................................................................................................................................... 3 2 Equipment under test attributes .................................................................................................................................... 3 3 Manufacturer information .............................................................................................................................................. 3 4 Test details .................................................................................................................................................................... 3 5 Tests summary .............................................................................................................................................................. 4 6 EUT description ............................................................................................................................................................. 5 6.1 General information ....................................................................................................................................................... 5 6.2 Ports and lines .............................................................................................................................................................. 5 6.3 Support and test equipment .......................................................................................................................................... 5 6.4 Changes made in the EUT ............................................................................................................................................ 5 6.5 Test configuration .......................................................................................................................................................... 6 6.6 Transmitter characteristics ............................................................................................................................................ 7 7 Transmitter tests ........................................................................................................................................................... 8 7.1 Transmitter power and maximum power spectral density test ....................................................................................... 8 7.2 Occupied bandwidth test ............................................................................................................................................. 22 7.3 Spurious emissions at RF antenna connector test ...................................................................................................... 33 7.4 Out of band radiated emissions below 40 GHz ........................................................................................................... 53 7.5 Out of band radiated emissions above 40 GHz up to 220 GHz ................................................................................... 70 7.6 Frequency stability test ................................................................................................................................................ 99 8 APPENDIX A Test equipment and ancillaries used for tests ..................................................................................... 101 9 APPENDIX B Measurement uncertainties ................................................................................................................. 103 10 APPENDIX C Test laboratory description ................................................................................................................. 104 11 APPENDIX D Specification references ..................................................................................................................... 104 12 APPENDIX E Test equipment correction factors ....................................................................................................... 105 13 APPENDIX F Abbreviations and acronyms ............................................................................................................... 113 Report ID: SIKRAD_FCC.25826_rev2.doc Date of Issue: 27-Aug-14 Page 3 of 113 1 Applicant information Client name: Siklu Communication Ltd. Address: 43 Hasivim street, Petach-Tikva 49517, Israel Telephone: +972 3921 4015 Fax: +972 3921 4162 E-mail: [email protected] Contact name: Mr. Baruch Schwarz 2 Equipment under test attributes Product name: Point-to-point wireless Ethernet link operating at 57-64 GHz Product type: Transceiver Model(s): EtherHaul EH-600T Serial number: S344000254 Hardware version: A0 Software release: V5.2.1 Receipt date 6/12/2014 3 Manufacturer information Manufacturer name: Siklu Communication Ltd. Address: 43 Hasivim street, Petach-Tikva 49517, Israel Telephone: +972 3921 4015 Fax: +972 3921 4162 E-Mail: [email protected] Contact name: Mr. Baruch Schwarz 4 Test details Project ID: 25826 Location: Hermon Laboratories Ltd. Harakevet Industrial Zone, Binyamin…

Text truncated - open the document above for the full version.

Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 1 of 10 SETUP PHOTOGRAPHS This document contains 9 photographs Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 2 of 10 Photograph No.1 Peak output power, OBW, spurious emissions measurement setup Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 3 of 10 Photograph No.2 Peak output power, OBW, spurious emissions measurement setup Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 4 of 10 Photograph No.3 Spurious emissions measurement setup in the anechoic chamber below 30 MHz Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 5 of 10 Photograph No.4 Spurious emissions measurement setup in the anechoic chamber in 30 -1000 MHz Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 6 of 10 Photograph No.5 Spurious emissions measurement setup in the anechoic chamber in 1-18 GHz Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 7 of 10 Photograph No.6 Spurious emissions measurement setup in the anechoic chamber, EUT close view Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 8 of 10 Photograph No.7 Spurious emissions measurement setup at the OATS in 18-40 GHz Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 9 of 10 Photograph No.8 Spurious emissions measurement setup at the OATS above 40 GHz Siklu Communication Ltd. FCC ID:2ACYESK-60GTDD-A1 Page 10 of 10 Photograph No.9 Frequency stability measurement setup