2ACYNA014202Premium Care II

BC-63_Manual_05.pdf 1 22/7/14 6:10 pm 2 Thank you for purchasing our A014201 digital green baby monitor. Your unit has been manufactured and checked under the strictest possible quality control to ensure that each monitor leaves the factory in perfect condition. In the unlikely event you find any defects or have any problem, please contact our dealer or service center. Please read this manual carefully to obtain maximum performance and extended service life from the unit. Features - Full digital technique operating in the 902.000MHz---928.000MHz with zero interference - Automatic hop and search for free channel - Operating range 800m in open space - Low radiating power (only 10% of normal DECT or 50% of ECO DECT) - Automatic power reduction system further reduce radiation level to 40% when baby unit and parent unit are within close vicinity - Talk back function on parent unit to soothe your baby - Capable of using multiple baby units to monitor more babies - Night light on baby unit with adjustable intensity level - Baby’s room temperature indication on both baby and parent unit - Battery status indicator and low battery alert on both baby and parent unit - Digitally adjustable microphone sensitivity - Audio and visual alert for out of range - Audio and visual Hi/Lo temperature alert - Digital volume control - Vibration alert - LED sound level meter - Parent unit operate with Li rechargeable battery - Sensor Touch Keys WARNING The A014201 should not be regarded as a medical device. Premature babies or those considered to be at risk should be under the supervision of your doctor or health personnel. Direct supervision of your baby at a regular interval by a responsible adult is strongly recommended in addition to using the A014201. BC-63_Manual_05.pdf 2 22/7/14 6:10 pm 3 DIGITALTECHNOLOGYANDAPRS This baby monitor employs full digital technology with zero interference. Theunitcanautomaticallyselectfreechannelorhoptofreechannelduring communicationtoavoidinterferencefromotherelectronicdevices.Inaddition, thankstotheAutomaticPowerReductionSystem(APRS)whichsensesthesignal strength between the baby and parent unit and automatically reduces the emission powerfrombabyunitwhenthetwounitsareinclosevicinity.Thelevelofradiation to baby is greatly reduced. POWER SUPPLY (A)Baby Unit (BU) 1.Operation from batteries Pressdownandslideopenthebatterydoorindirectionasshown.Insert threepiecesAAAsize(UM-4)alkalinebatteriesintothecompartment. Observe correct polarities indication. N.B.Forbestperformance,donotmixuseoldandnewbatteriesoralkalineand rechargeable batteries. BC-63_Manual_05.pdf 3 22/7/14 6:10 pm 4 2.Operation usingAC adapter TheunitcanbeoperatedonACmainsusingthesupplied5VACadapter. ConnecttheoutputplugofadaptertoUSBport16,makesurethepolari- tyiscorrect.Thepowersupplyfromthebatterywillbecutoffoncethe adapter’s output plug is inserted into USB port 16 . (B)Parent Unit (PU) 1.Operation from battery pack TheLipolymerbatterypackisalreadyinstalledintheunit.Toexchange battery pack, remove belt clip and slide open the battery door in direction as shown, take out the battery pack and disconnect from socket. 16 BC-63_Manual_05.pdf 4 22/7/14 6:10 pm 2.Charging up the Lithium rechargeable battery Connect the output plug of supplied 5VAC adapter to USB port 37 of the chargerstand,makesurethepolarityiscorrect.Theunitcaneitherbein switchONorOFFcondition,placeitintothechargerstand.Thecharging indicator36shouldlightupwhite.Adjustthepositionofparentunitin casetheindicator36doesnotlightup.Duringcharging,thepoweron/ batterylowicon27shouldbeflashingred.Oncethebatteryisfully chargedup,thepoweron/batterylowicon27shouldstaysteady green.Eitheryoucantakeitoutorkeepplacingitinthechargerstandwill causenodamagetobattery.Inthelattercase,whenthebatteryisbeing consumedandvoltagefallstoacertainlevel,thechargerstandwill automatically start charging up the battery again. Note:Beforeusingtheparentunitforthefirsttime,chargeuptheLipolymer batteryforatleastthreehours.Itisrecommendedtoswitchofftheunitduringfirst charging. EvenwithouttheLibatterypackbeinginstalled,theunitcanstillopratenormally onceplaceinchangerstand,whilethepoweronicon27willalwaysstaysteady green. CAUTION:BESURETHEBATTERYINPARENTUNITISRECHARGEABLE TYPEBEFOREPLACINGINCHARGERSTAND.OTHERWISEEXPLSIONMY RESULT . 5 ! 37 BC-63_Manual_05.pdf 5 22/7/14 6:10 pm 6 PAIRING Thisprocessistomatchtheparentunitwithbabyunitsothattheycancommunicatewith eachotherwhilenootherdevices(evenbabymonitorofidenticalmodel)caninterferewith you or receiving your signal. Thebabyandparentunitarealreadypairedwhentheyareshippedfromfactory.However, werecommendtoperformpairingprocessagainincaseinterferenceisexperiencedor when extra BU is added to work with the PU. 1. Press and hold the talk button 35 of PU. 2.LongpressthepowerON/OFFbutton18andwaituntilastartsflashinggreen. Release both buttons 18 and 35 . 3.LongpresstheON/OFFbutton1for3sectoswitchontheBU.Nowtouchand holdiconfor5secandwaituntilashowsteadygreenwhiletheBUnumber icon151or2startsflashinggreen.Releasethefingertouchingicon15.Perform same to the other BU that can be purchased optionally. 4.Usethetouchkeys23tosettheBUnumbertoeither1or2.DONOTset bothBUtosamenumberorotherwisethesystemwillnotoperatenormally.Short pressthebutton1toconfirmyoursetting,theBUnumbernowshowsteady while starts flashing. steady flashing BC-63_Manual_05.pdf 6 22/7/14 6:10 pm 7 5.NowshortpressagainthepowerON/OFFbutton1ofoneBU.Ifpairingis successful,theon both PU and BU should change steady green while two beep sound is heard in PU with the corresponding BU number icon 33 or 34 being shown up. 6.Shortpressbutton1oftheremainingBU,twobeepsoundisheardinPUwith theflashestwotimesandthecorrespondingBUnumbershowup.The onthis BU change from flashing to become steady green. 7.Longpressbutton1and18toswitchoffallBUandPUandthenswitchthem on again, the baby monitor is now ready for operation. 8.IncaseBUandPUcannotcommunicatewitheachother,repeatpairingprocess again. N.B.Iforiginallythereisonlyone…

Text truncated - open the document above for the full version.

ALT GROUP BABYMOOV CORP. 022311 – 6 Authority to Act as Agent Date: 2014-11-27 American Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 To Whom It May Concern: _____ SGS-CSTC Standards Technical Services Co., Ltd._____ is authorized to act on our behalf, until otherwise notified, for applications to American Certification Body, Inc. (ACB). We certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Further, no party, as defined in 47 CFR 1.2002 (b) , to the application is subject to denial of federal benefits, that includes FCC benefits. Thank you, Agency Agreement Expiration Date: _____(Typically 8 – 12 months)_____ By: __________________________ _____Mr Marguerin Xavier__ (Signature 1 ) (Print name) Title: ____Quality manager_______ On behalf of: _____ALT GROUP BABYMOOV CORP._____ (Company Name) Telephone: ___ (855) 517-2229__________ 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

ALT GROUP BABYMOOV CORP. 022311 – 6 Request for Confidentiality Date: 2014-11-27 Subject: Confidentiality Request for: FCC ID :_2ACYNA014202_____________________ IC:_12292A-A014202__________________ Pursuant to FCC 47 CRF 0.457(d) and 0.459 and IC RSP-100, Section 10, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit Short Term Permanent Block Diagrams Short Term External Photos Short Term Permanent* 2 Internal Photos Short Term Permanent Operation Description/Theory of Operation Short Term Permanent Parts List & Placement/BOM Short Term Permanent Tune-Up Procedure Short Term Permanent Schematics Short Term Test Setup Photos Short Term Permanent* User’s Manual *Note: ______(Insert Explanation as Necessary)______ _____ALT GROUP BABYMOOV CORP.___ has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of ___(specify number of days not to exceed 180) 3 ___ days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: The applicant understands that until such time that IC distinguishes between Short Term and Permanent Confidentiality, either type of marked exhibit above will simply be marked Confidential when submitted to IC. Sincerely, By: __________________________ ______Mr Marguerin Xavier__________________ (Signature/Title 4 ) (Print name) 2 - The asterisked items (*) require further justification before permanent confidentiality will be allowed. These also currently require review by the FCC under their Permit-But-Ask policy before the grant is issued and can delay completion of an application. Further justification should be added to the note above. One such example for a potted device would be: “The EUT is FULLY potted using a non-removable epoxy based material. Removal of potting material causes irreparable damage to internal circuitry. See photographs exhibits that outline the device before and after potting.” 3 - Please refer to http://acbcert.com/documents/misc-docs/Memo-Short-Term-Vs-Standard-Confidentiality.pdf for complete details. 4 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

External Photo Parent unit Baby Unit

LABEL LOCATION LETTER Federal Communications Commission Authorization and Evaluation Division The FCC ID: 2ACYNA014202 label is placed in battery compartment because of the limitation of the small size and special construction of the product. Battery compartment is the only choice when battery cover is not acceptable by FCC. The product will be sold without battery. At the time users put in or change battery, they can find the FCC ID easily. On the box of the product will inform users that FCC ID can be found in the battery compartment at the time of purchase. By: ________________________Mr Marguerin Xavier__ (Signature 1 ) (Print name) Title: ____Quality manager_______ On behalf of: _____ALT GROUP BABYMOOV CORP._____ (Company Name) Telephone: ___ (855) 517-2229__________

Internal Photo Parent Unit Baby Unit

Charger and Adapter Photo

SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM141000526601 Page: 1 of 2 FCC ID: 2ACYNA014202 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. RF Exposure Compliance Requirement 1. Standard requirement Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.2m normally can be maintained between the user and the device. (a) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S)(mW/cm 2 ) Averaging Times ׀E׀ 2 ׀ ,H׀ 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842/f 4.89/f (900/f)* 6 30-300 61.4 0.163 1.0 6 300-1500 -- -- F/300 6 1500-100000 -- -- 5 6 (b) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S)(mW/cm 2 ) Averaging Times ׀E׀ 2 ׀ ,H׀ 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 -- -- F/1500 30 1500-100000 -- -- 1.0 30 Note: f=frequency in MHz; *Plane-wave equivalent power density SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM141000526601 Page: 2 of 2 FCC ID: 2ACYNA014202 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2. MPE Calculation Method E (V/m)=(30*P*G) 0.5 /d Power Density: Pd(W/m 2 )=E 2 /377 E=Electric Field (V/m) P=Peak RF output Power (W) G=EUT Antenna numeric gain (numeric) d= Separation distance between radiator and human body (m) The formula can be changed to Pd= (30*P*G)/(377*d 2 ) From the peak EUT RF output power, the minimum mobile separation distance, d=0.2m, as well as the gain of the used antenna, the RF power density can be obtained. 3. Calculated Result and Limit For mother unit: Frequency (MHz) Antenna Gain (Numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 915.8 1.0 -9.01 0.126 0.2507 0.60 Complies 921.4 1.0 -9.97 0.101 0.2009 0.61 Complies 927.0 1.0 -7.16 0.192 0.3820 0.62 Complies For baby unit: Frequency (MHz) Antenna Gain (Numeric) Peak Output Power (dBm) Peak Output Power (mW) Power Density (S) (mW/cm 2 ) Limit of Power Density (S) (mW/cm 2 ) Test Result 915.8 1.0 -8.29 0.148 0.2944 0.60 Complies 921.4 1.0 -9.63 0.109 0.2168 0.61 Complies 927.0 1.0 -10.48 0.090 0.1790 0.62 Complies

SGS-CSTC Standards Technical Services Co., Ltd. 198 Kezhu Road, Scientech Park, Guangzhou Economic & Technological Development District, Guangzhou, China 510663 Telephone: +86 (0) 20 82155555 Fax: +86 (0) 20 82075059 Email: [email protected] Report No.: GZEM141000526601 Page: 1 of 44 FCC ID: 2ACYNA014202 Jerry Chan Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. The report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the federal government. All test results in this report can be traceable to National or International Standards. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only 1 Cover Page TEST REPORT Application No.: GZEM1410005266CR Applicant: ALT PARTNERS/BABYMOOV Manufacturer: The same as applicant FCC ID: 2ACYNA014202 Product Name: Premium Care II Product Description: Radio digital baby monitor with 915MHz as carrier Model No.: A014202, BC-63 ♣ ♣ Please refer to section 3 of this report for further details. Standards: CFR 47 FCC PART 15 SUBPART C:2013 section 15.249 Date of Receipt: 2014-10-13 Date of Test: 2014-10-17 to 2014-11-27 Date of Issue: 2015-01-09 Test Result : Pass* *In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM141000526601 Page: 2 of 44 FCC ID: 2ACYNA014202 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 2 Version Revision Record Version Chapter Date Modifier Remark 00 2015-01-09 Original Authorized for issue by: Tested By 2014-10-17 to 2014-11-27 (Bill Ma) / Project Engineer Date Prepared By 2014-12-02 (Karon Yang) / Clerk Date Checked By 2014-12-17 (Jerry Chan) / Reviewer Date SGS-CSTC Standards Technical Services Co., Ltd. Report No.: GZEM141000526601 Page: 3 of 44 FCC ID: 2ACYNA014202 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 3 Test Summary Test Test Requirement Test method Result Field Strength of Fundamental FCC PART 15 C section 15.249 (a) ANSI C63.10: Clause 6.6 PASS Field Strength of Unwanted Emissions FCC PART 15 C section 15.249 (a) section 15.249 (d) ANSI C63.10: Clause 6.4, 6.6 and 6.7 PASS Band Edges FCC PART 15 C secti…

Text truncated - open the document above for the full version.

Test Setup Photo 1.1 RADIATED SPURIOUS EMISSION TEST SETUP Below 1GHz: For MOTHER UNIT: For BABY UNIT: Above 1GHz: For MOTHER UNIT: For BABY UNIT: 1.2 CONDUCTED EMISSION TEST SETUP For MOTHER UNIT: For BABY UNIT: