2ACYNA014618WiFi Key Babycamera

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC statement: update version. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. nOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. iC statement: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Using ThE a014618 WiFi kEy (sOld sEparaTEly) • Turn on the Zero Emission Camera and install the My Babycamera app. Then insert the Wi-Fi key in the USB port (8). • Wait for about a minute for the network to appear in the list of available Wi-Fi networks. • Select the «Babymoov cam» network. Enter the password 12345678, then click «Connect». • You are now connected to the «Babymoov cam» network and can start using the My Babycamera app. n.B.: This Wi-Fi key will ensure you can continue using your Zero Emission Camera even when in places with no internet service. In this case, operation will be in Wi-Fi and not PLC mode. Also note that the notifications do not work when using the A014614 Wi-Fi key. En Instructions for use • Instrucciones de uso • Notice d’utilisation WiFi key - Llave WiFi - Clé Wifi Zero Emission Camera Ref.: A014618 ALT Group Babymoov Corp. 715 Washington Street FL 3 HOBOKEN, NJ 07030 USA www.babymoov.com Designed and engineered by Babymoov in France 1-855-517-2456 FCC ID: 2ACYNA014618 IC ID: 12292A-A014618 Images are provided for illustrative purpose - Fotos no contractuales – Images non contractuelles A014618-Manual-Artwork-02 8 Cet équipement respecte les limitations FFC (Commission Fédérale de communication) d’exposition aux radiations mis en place dans un environnement non controlé. Ce transmetteur ne doit pas être situé ou mis en fonctionnement près d’une autre antenne ou transmetteur. autorisation FCC (Commission fédérale des communications) : version mise à jour. aVErTissEMEnT : tout changement ou modification de cet appareil non approuvé formellement par la partie responsable de la conformité peut annuler l’autorisation de l’utilisateur à utiliser cet appareil. rEMarQUE : cet équipement a été testé et déclaré conforme aux normes applicables aux appareils numériques de catégorie B, en vertu de l’article 15 des réglementations de la FCC. Ces normes visent à fournir une protection raisonnable contre les interférences dangereuses dans une installation à domicile. Cet appareil génère, utilise et peut émettre de l’énergie de fréquence radio et, s’il n’est pas installé et utilisé conformément aux instructions, peut causer des interférences nuisibles aux communications radios. Cependant, rien ne garantit l’absence d’interférences dans une installation particulière. Si cet équipement produit des interférences préjudiciables à une bonne réception radio ou télévision, ce qui peut être déterminé en allumant et en éteignant l’appareil, l’utilisateur peut tenter de résoudre le problème de l’une des façons suivantes : - Réorienter ou déplacer l’antenne réceptrice, - Accroître la distance séparant l’appareil du récepteur, - Brancher l’appareil sur une prise d’un autre circuit électrique que celui sur lequel est branché le récepteur, - Contacter un revendeur ou un technicien radio/TV qualifié pour obtenir de l’aide. Cet appareil est conforme à l’article 15 de la réglementation FCC. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférences nuisibles et (2) cet appareil doit accepter toute interférence reçue, y compris l’interférence pouvant gêner le fonctionnement de l’appareil. autorisation iC (industry Canada) : Cet appareil est conforme à l’article RSS-210 d’Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférences nuisibles et (2) cet appareil doit accepter toute interférence reçue, y compris l’interférence pouvant gêner le fonctionnement de l’appareil. FOnCTiOnnEMEnT aVEC la Clé WiFi a014618 (VEndUE séparéMEnT) • Une fois votre Zero Emission Camera allumée et votre application My Babycamera installée, insérez la clé wifi dans le port USB (8) prévu à cet effet. • Veuillez patienter environ 1 minute le temps que le réseau apparaisse parmi les réseaux wifi disponibles. • Sélectionnez le réseau « Babymoov cam ». Rentrez le…

Text truncated - open the document above for the full version.

External Photos

FCC ID: 2ACYNA014618 IC: 12292A-A014618

Internal Photos

Report No. RXA1501-0015SAR01R1 Page 1 of 58 TESTING No. L2264 SAR TEST REPORT Product Name WiFi Key Babycamera Model Name A014618 Brand Name Babymoov FCC ID 2ACYNA014618 Client ALT GROUP BABYMOOV CORP. Manufacturer ALT GROUP BABYMOOV CORP. Date of issue March 27, 2015 TA Technology (Shanghai) Co., Ltd. TA Technology (Shanghai) Co., Ltd. Test Report Report No. RXA1501-0015SAR01R1 Page 2 of 58 GENERAL SUMMARY Reference Standard(s) FCC 47CFR §2.1093 Radiofrequency Radiation Exposure Evaluation: Portable Devices ANSI C95.1, 1992: Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.(IEEE Std C95.1-1991) IEEE Std 1528™-2003: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques. KDB 865664 D01 SAR measurement 100 MHz to 6 GHz v01r03 SAR Measurement Requirements for 100 MHz to 6 GHz KDB 447498 D01 Mobile Portable RF Exposure v05r02: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies KDB 447498 D02 SAR Procedures for Dongle Xmtr v02: SAR Measurement Procedures for USB Dongle Transmitters. KDB 248227 D01 SAR meas for 802 11 a b g v01r02: SAR Measurement Procedures for 802.11a/b/g Transmitters. Conclusion This portable wireless equipment has been measured in all cases requested by the relevant standards. Test results in Chapter 7 of this test report are below limits specified in the relevant standards for the tested bands only. General Judgment: Pass Comment The test result only responds to the measured sample. Approved by Kai Xu Director Revised by Jiangpeng Lan SAR Manager Performed by Jie Li SAR Engineer TA Technology (Shanghai) Co., Ltd. Test Report Report No. RXA1501-0015SAR01R1 Page 3 of 58 TABLE OF CONTENT 1. General Information ........................................................................................................................ 5 1.1. Notes of the Test Report .......................................................................................................... 5 1.2. Testing Laboratory ................................................................................................................... 5 1.3. Applicant Information ............................................................................................................... 6 1.4. Manufacturer Information ......................................................................................................... 6 1.5. Information of EUT ................................................................................................................... 7 1.6. EUT Antenna Locations ........................................................................................................... 8 1.7. The Maximum Reported SAR 1g ............................................................................................... 8 1.8. Test Date ................................................................................................................................. 8 2. SAR Measurements System Configuration ..................................................................................... 9 2.1. SAR Measurement Set-up ....................................................................................................... 9 2.2. DASY5 E-field Probe System ................................................................................................ 10 2.2.1. EX3DV4 Probe Specification .......................................................................................... 10 2.2.2. E-field Probe Calibration .................................................................................................. 11 2.3. Other Test Equipment ............................................................................................................ 11 2.3.1. Device Holder for Transmitters ........................................................................................ 11 2.3.2. Phantom ......................................................................................................................... 12 2.4. Scanning Procedure .............................................................................................................. 12 2.5. Data Storage and Evaluation ................................................................................................. 14 2.5.1. Data Storage ................................................................................................................... 14 2.5.2. Data Evaluation by SEMCAD ......................................................................................... 14 3. Laboratory Environment ................................................................................................................ 16 4. Tissue-equivalent Liquid ............................................................................................................... 17 4.1. Tissue-equivalent Liquid Ingredients ...................................................................................... 17 4.2. Tissue-equivalent Liquid Properties ....................................................................................... 17 5. System Check ............................................................................................................................... 18 5.1. Description of System Check ................................................................................................. 18 5.2. System Check Results ........................................................................................................... 19 6. Operational Conditions during Test ............................................................................................... 20 6.1. General Description of Test Procedures ................................................................................ 20 6.2. Measurement Variability ..............................…

Text truncated - open the document above for the full version.

• The test results reported in this test report shall refer only to the sample actually tested and shall not refer or be deemed to refer to bulk from which such a sample may be said to have been obtained. • This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to copy or distribute this report. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results referenced from this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. • For Terms And Conditions of the services, it can be provided upon request. • The evaluation data of the report will be kept for 3 years from the date of issuance. TRF no.: FCC 15C_Tx_b Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, D Block, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Tel: (86 755) 8601 6288 Fax: (86 755) 8601 6751 Website: www.china.intertek-etlsemko.com ALT GROUP BABYMOOV CORP. Application For Certification FCC ID: 2ACYNA014618 WiFi Key Babycamera Model: A014618 2.4GHz WiFi Transceiver Report No.: 140806014SZN-001 We hereby certify that the sample of the above item is considered to comply with the requirements of FCC Part 15, Subpart C for Intentional Radiator, mention 47 CFR [10-1-13] Prepared and Checked by: Approved by: Sign on file Jenner Liu Assistant Engineer Andy Yan Senior Project Engineer Date: December 11, 2014 INTERTEK TESTING SERVICE TRF no.: FCC 15C_TX_b FCC ID: 2ACYNA014618 Report No.: 140806014SZN-001 i LIST OF EXHIBITS INTRODUCTION EXHIBIT 1: Summary of Tests EXHIBIT 2: General Description EXHIBIT 3: System Test Configuration EXHIBIT 4: Measurement Results EXHIBIT 5: Equipment Photographs EXHIBIT 6: Product Labeling EXHIBIT 7: Technical Specifications EXHIBIT 8: Instruction Manual EXHIBIT 9: Confidentiality Request EXHIBIT 10: Miscellaneous Information EXHIBIT 11: Test Equipment List INTERTEK TESTING SERVICES TRF no.: FCC 15C_TX_b FCC ID: 2ACYNA014618 Report No.: 140806014SZN-001 ii MEASUREMENT/TECHNICAL REPORT WiFi Key Babycamera Model: A014618 FCC ID: 2ACYNA014618 This report concerns (check one) Original Grant X Class II Change Equipment Type: DTS - Part 15 Digital Transmission Systems (WiFi transmitter portion) Deferred grant requested per 47 CFR 0.457(d)(1)(ii)? Yes No X If yes, defer until : date Company Name agrees to notify the Commission by: date of the intended date of announcement of the product so that the grant can be issued on that date. Transition Rules Request per 15.37? Yes No X If no, assumed Part 15, Subpart C for intentional radiator - the new 47 CFR [10-01-13] Edition] provision. Report prepared by: Jenner Liu Intertek Testing Services Shenzhen Ltd. Kejiyuan Branch 6F, Block D, Huahan Building, Langshan Road, Nanshan District, Shenzhen, P. R. China Phone: (86 755) 8614 0639 Fax: (86 755) 8614 6751 INTERTEK TESTING SERVICES TRF no.: FCC 15C_TX_b FCC ID: 2ACYNA014618 Report No.: 140806014SZN-001 iii Table of Contents 1.0 Summary of Test results ............................................................................................................................. 2 2.0 General Description ...................................................................................................................................... 4 2.1 Product Description ..................................................................................................................................... 4 2.2 Related Submittal(s) Grants ....................................................................................................................... 5 2.3 Test Methodology ........................................................................................................................................ 5 2.4 Test Facility .................................................................................................................................................. 5 3.0 System Test Configuration ......................................................................................................................... 7 3.1 Justification .................................................................................................................................................. 7 3.2 EUT Exercising Software ........................................................................................................................... 7 3.3 Special Accessories .................................................................................................................................... 7 3.4 Measurement Uncertainty .......................................................................................................................... 8 3.5 Equipment Modification .............................................................................................................................. 8 3.6 Support Equipment List and Description ................................................................................................. 8 4.0 Measurement Results ................................................................................................................................ 10 4.1 Maximum Conducted Output Power at Antenna Terminals ...................................................................... 10 4.2 Minimum 6 dB RF Bandwidth .....................................................................................................…

Text truncated - open the document above for the full version.

Conducted Emission

Radiated Emission