2ADAT-T12S2T12-S2 Torquemeter

A1979−10.0 en Digital Torque Transducer T12 Mounting Instructions 3 T12 A1979−10.0 enHBM ContentsPage Contents Safety instructions5.............................................. 1 Markings used9............................................... 1.1Symbols on the transducer and / or Stator9................... 1.2The markings used in this document10........................ 2 Scope of supply11............................................. 3 Operation11................................................... 4 Application12.................................................. 5 Signal flow13.................................................. 6 Structure and mode of operation14.............................. 7 Mechanical installation16....................................... 7.1Important precautions during installation16.................... 7.2Conditions on site17........................................ 7.3Mounting position17........................................ 7.4Installing the slotted disc (rotational speed measuring system only)18................................................... 7.5Installing the rotor19........................................ 7.6Fitting the protection against contact (option)21................ 7.7Installing the stator27....................................... 7.7.1 Preparing with the mounting kit (included among the items supplied)28.......................................... 7.7.2 Aligning the stator30.................................. 7.7.3 Stator installation over the protection against contact (option)32........................................... 7.8Optical rotational speed/angle of rotation measuring system (option)33................................................. 7.8.1 Axial alignment33.................................... 7.8.2 Radial alignment34................................... 8 LED status display36........................................... 8.1Measuring mode operation36................................ 8.2Rotor clearance setting mode operation36..................... 8.3Rotational speed measuring system setting mode operation36... 9 Electrical connection37......................................... 9.1General information37...................................... 9.2Shielding design39......................................... T12 4 A1979−10.0 enHBM 9.3Connector pin assignment39................................ 9.4Supply voltage43.......................................... 10 Shunt signal45................................................. 11 Load-carrying capacity46....................................... 12 TEDS47....................................................... 13 Maintenance54................................................. 14 Waste disposal and environmental protection55.................. 15 Specifications56............................................... 15.1 Nominal (rated) torque 100 Nm to 1 kNm56................... 15.2 Nominal (rated) torque 2 kNm to 10 kNm63................... 16 Dimensions70................................................. 16.1 Rotor 100 Nm to 200 Nm70................................ 16.2 Rotor 500 Nm to 10 kNm71................................ 16.3 Stator 100 Nm to 200 Nm with rot.speed meas. system72...... 16.4 Stator 100 Nm to 200 Nm with rot. speed meas. system73..... 16.5 Stator 100 Nm to 10 kNm with rot. speed meas. system74..... 16.6 Stator 100 Nm to 200 Nm with prot. against contact75......... 16.7 Stator 100 Nm to 200 Nm with prot. against contact76......... 16.8 Stator 500 Nm to 1 kNm with prot. against contact77.......... 16.9 Stator 2 kNm to 10 kNm with prot. against contact78........... 16.9.1 Protection against contact plates 100 Nm to 200 Nm79... 16.9.2 Protection against contact plates 500 Nm to 10 kNm79... 16.10 Mounting dimensions80..................................... 17 Supplementary technical information81.......................... 18 Condition at the time of delivery82............................... 19 Ordering numbers87........................................... 20 Accessories88................................................. 5 T12 A1979−10.0 enHBM Safety instructions FCC Compliance & Advisory Statement for Option 7, Code U This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including in- terference that may cause undesired operation. The FCC identifier or the unique identifier, as appropriate, must be displayed on the device. ModelFCC IDIC T12, 100 Nm, 200 Nm2ADAT−T12S212438A−T12S2 T12, 500 Nm, 1 kNm2ADAT−T12S312438A−T12S3 T12, 2 kNm, 3 kNm2ADAT−T12S412438A−T12S4 T12, 5 kNm2ADAT−T12S512438A−T12S5 T12, 10 kNm2ADAT−T12S612438A−T12S6 The FCC ID number in dependence of measuring range: label example only on the Stator FCC ID and IC number range. Label example with FCC ID and IC number. Location on the stator of the device. FCC ID: 2ADAT-T12S2 IC: 12438A­T12S2 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Fig 1.1:Example of the label Industry Canada for Option 7, Code U IC: 12483A−T12S2 This device complies with Industry Canada standard RSS210. This device complies with Industry Canada license−exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux norme RSS210 d’Industrie Canada. T12 6 A1979−10.0 enHBM Cet appareil est conforme aux normes d’exemption de licence RSS d’Industry Canada. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d’interférence et …

Text truncated - open the document above for the full version.

Variants for FCC-Certification Model T12 HBM: business 1 15.10.2014 © HBM Type Approval Electrical Parts Variations of mechanical parts of rotor (variations have no influence on RF characteristics) T12-S2 Variants 2 HBM: business 15.10.2014 HBM: customized 100Nm 200Nm FCC ID: 2ADAT-T12S2 IC: 12438A-T12S2 + ØD=122mm ØD © HBM One type is EMC tested 3 HBM: business use 15.10.2014 Basis elements (stator and all electrical parts on the rotor) are always the same Same RF characteristics: •All types of one size have the same stator, same stator PCB, same primary coil, same rotor PCB, same secondary coil on the rotor and have complete metallic housing of rotor and stator. Possible mechanical modifications (no influence on RF characteristics): •Variations of the thickness of the strain detection zone to realize different torque ranges (e.g. 100Nm, 200Nm,...) •Variations of flanges (e.g. diameter of PCD, length, ...) to realize different mechanical interface (mountable to customers counter flange) Strain detection zone Rotor PCB Stator (including primary coil, (for each size defined diameter) Secondary coil on rotor Mechanical variations (examples) Flange ØD

Managing Director: Andreas Hüllhorst – Chairman of the Board: Eoghan O’Lionaird Registered at Darmstadt HRB 1147 HBM: public External Photos T12 S2

Managing Director: Andreas Hüllhorst – Chairman of the Board: Eoghan O’Lionaird Registered at Darmstadt HRB 1147 HBM: public LABEL Position Managing Director: Andreas Hüllhorst – Chairman of the Board: Eoghan O’Lionaird Registered at Darmstadt HRB 1147 HBM: public Schriftgröße/n - Font size/s FCC ID bzw. CI Code min. 8 Punkte [*pt] = ~2,8 mm Stellungnahme - Statement Text min. 5 Punkte [*pt] = ~1,8 mm *DTO-Punkte / 1 pt = 0,35 27 mm Abmessungen – Dimension [mm] B = 50,0 +2 H = 18,0 +2 R = 1,0 ±0,2 Material: self-adhesive polyester security film, 60 μm Color: silver, matt coated Adhesive: Permanent adhesive Temperature range: -40 ° C to +150 ° C Characteristics: weather resistant, sea water, resistant to many solvents, weak acids and alkalis

Managing Director: Andreas Hüllhorst – Chairman of the Board: Eoghan O’Lionaird Registered at Darmstadt HRB 1147 HBM: public Internal Photos T12 Rotor The rotor includes 4 PCB Front Rear Managing Director: Andreas Hüllhorst – Chairman of the Board: Eoghan O’Lionaird Registered at Darmstadt HRB 1147 HBM: public Managing Director: Andreas Hüllhorst – Chairman of the Board: Eoghan O’Lionaird Registered at Darmstadt HRB 1147 HBM: public Stator All PCBs are covered with a potting component Front Rear Managing Director: Andreas Hüllhorst – Chairman of the Board: Eoghan O’Lionaird Registered at Darmstadt HRB 1147 HBM: public Stator Head

Vetr,ç,ç'' Test Report # EMCC-0401 97BB Page 1 of 29 lssue Date: 2014-10-31 Test of HBM Tl2 type 52 to 47 CFR 15.225 TEST REPORT # EMCC-04019788, 2014-10-31 EQUIPMENT UNDER TEST: Trade Name: Type Designation(s): Serial Number: Equipment Class: Manufacturer: Address: Phone: Fax: RELEVANT STANDARD(S): T12 S2 Rotor: 1 53030053, Stator: 18327 0022 Low Power Transceiver Hottinger Baldwin Messtechnik GmbH lm Tiefen See 45 64293 Darmstadt Germany +49 6151 803-681 +49 6151 803-98790 47 CFR 15.225 MEASUREMENT PROCEDURE: E Rss-cen tssue 3 X ANSI c63.10-2009 n otner TEST REPORT PREPARED BY: Ludwig Kraft EMCCONS DR. RASEK GMbH & CO. Moggast, Boelwiese I 91320 Ebermannstadt Germany Phone: +49 9194 9016 Fax: +4991948125 E-mail: l.kraft(@emcc.de KG TEST PERSONNEL:HEAD OF GROUP: t, ì,0. Ludwig KraftWolfgang EMCCons ON. RRSCX GmbH & Co. KG Moggast, Boelwiese 8 91320 Ebermannstadt Germany FCC Registration # 878769 lndustry Canada L¡sling # 3464C o40r97BA DRAFÌI E !,1C. Rac o, Safe!¡ år'd Enlicnrer:al Tgsl¡îg fl nnn s rl Deutsche Akkreditierungsstelle 0.Pr,12067.0r 00 Telephone: +49 9194 9016 Telefax: +49 9194 8125 Mail: [email protected] Web: http://vwwv.emcc.de Test Report # EMCC-040197BB Page 2 of 29 Issue Date: 2014-10-31 Test of HBM T12 type S2 to 47 CFR 15.225 CONTENTS Page 1 GENERAL INFORMATION ............................................................................................................................................................... 3 1.1 Purpose ............................................................................................................................................................................. 3 1.2 Limits and Reservations................................................................................................................................................... 3 1.3 Test Location .................................................................................................................................................................... 3 1.4 Manufacturer ..................................................................................................................................................................... 3 1.5 Dates and Test Location................................................................................................................................................... 4 1.6 Ordering Information ........................................................................................................................................................ 4 1.7 Climatic Conditions .......................................................................................................................................................... 4 2 Product Description ......................................................................................................................................................................... 5 2.1 Equipment Under Test (EUT) ........................................................................................................................................... 5 2.2 Intended Use ..................................................................................................................................................................... 5 2.3 EUT Peripherals/Simulators ............................................................................................................................................. 6 2.4 Mode of operation during testing and test set-up .......................................................................................................... 7 2.5 Modifications required for compliance ........................................................................................................................... 7 3 Test Results Summary .................................................................................................................................................................... 8 4 Antenna Requirement ...................................................................................................................................................................... 9 4.1 Regulation ......................................................................................................................................................................... 9 4.2 Result ................................................................................................................................................................................. 9 5 Power line Conducted Emissions Test ........................................................................................................................................ 10 5.1 Regulation ....................................................................................................................................................................... 10 5.2 Test Equipment ............................................................................................................................................................... 11 5.3 Test Procedures .............................................................................................................................................................. 11 5.4 Test Result ...................................................................................................................................................................... 11 5.5 Measurement Plots ......................................................................................................................................................... 12 6 Spectrum Mask .............................................................................................................................................................................. 13 6.1 Regulation ................................................................................................................................................…

Text truncated - open the document above for the full version.

Test Report # EMCC-040197BB Page 1 of 37 Issue Date: 2014-10-31 Test of HBM T12 type S2 to 47 CFR 15.225 Page 1 of 3 ANNEX 1 TO TEST REPORT # EMCC-040197BB, 2014-10-31 PHOTOGRAPHS OF TEST SET-UP EQUIPMENT UNDER TEST: Trade Name: T12 Type Designation(s): S2 Serial Number: 153030053 (Rotor); 183270022 (Stator) Equipment Class: Low Power Transceiver Manufacturer: Hottinger Baldwin Messtechnik GmbH Address: Im Tiefen See 45 64293 Darmstadt Germany Phone: +49 6151 803-681 Fax: +49 6151 803-98790 RELEVANT STANDARD(S): 47 CFR 15.225 MEASUREMENT PROCEDURE: RSS-Gen Issue 3 ANSI C63.10-2009 Other CONTENTS Page Annex 1 to Test Report # EMCC-040197BB, 2014-10-31 ....................................................................................................................... 1 1 Radiated and conducted Emissions test ....................................................................................................................................... 2 2 Carrier frequency stability ............................................................................................................................................................... 3 Telephone: +49 9194 9016 Telefax: +49 9194 8125 Mail: [email protected] Web: http://www.emcc.de EMCCons DR. RAŠEK GmbH & Co. KG Moggast, Boelwiese 8 91320 Ebermannstadt Germany FCC Registration # 878769 Industry Canada Listing # 3464C 040197BB Test Report # EMCC-040197BB Page 2 of 3 Issue Date: 2014-10-31 Test of HBM T12 type S2 to 47 CFR 15.225 1 RADIATED AND CONDUCTED EMISSIONS TEST Radiated emissions measurement at 3 m distance 9 kHz – 30 MHz Radiated emissions measurement at 3 m distance, 30 MHz – 149.16 MHz Conducted emissions measurement 9 kHz – 30 MHz Conducted emissions measurement 9 kHz – 30 MHz © EMCCons DR. RAŠEK GmbH & Co. KG 2014 040197BB Test Report # EMCC-040197BB Page 3 of 3 Issue Date: 2014-10-31 Test of HBM T12 type S2 to 47 CFR 15.225 2 CARRIER FREQUENCY STABILITY Test setup Detailed view inside climatic chamber intentionally left blank intentionally left blank © EMCCons DR. RAŠEK GmbH & Co. KG 2014 040197BB