2ADS4-WAVENODEWaveNode (Node RF)

WAVE NODE USER MANUAL Rev0 Revision History RevisionDateDescription 020.07.2022Initial release Wave Node - User Manual Rev02 Table of Contents General Information4 Glossary4 Device Safety5 Technical specifications6 Installation6 Operation7 User interface7 Functions and menu navigation8 Appendices18 Wave Node - User Manual Rev03 1.General Information The Wave Node is a Radio Frequency transmitter designed by Pixmob, intended for low power broadcasting. The data transmitted is aimed at wirelessly controlling LED-based devices. 2.Glossary Pixel: Refer to a wearable device embedding an LED and being controlled by the Wave Node. Wave Node - User Manual Rev04 3. Device Safety General safety notes ● The device is not water resistant ● Do not attempt to open the device FCC Caution This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna. Wave Node - User Manual Rev05 4.Technical specifications Power specifications Input voltage5VDC Current500mA RF specifications TypeIntentional transmitter Frequency915MHz Transmission power+14dBm/25mW Modulation typeOOK Antenna typeDetachable (whip) 5.Installation ● Connect the antenna (provided) to the Wave Node ○ Position the antenna vertically ● Plug in the USB cable - type A end - (provided) to the power brick (provided) ● Plug in the USB cable - type B end - (provided) to the Wave Node ● Operate the device as described in the Operation section Wave Node - User Manual Rev06 6.Operation User interface ●1: LCD Screen: Display the different Menus and selected parameters. ● 2: LED Status: The button LED will strobe when RF Output is ON. ● 3: Push Buttons : oMenu Selection oConfig Line 1 oConfig Line 2 oConfig Line 3 ● 4:RF Output interface: The middle LED will strobe when RF output is ON. Wave Node - User Manual Rev07 Functions and menu navigation 1. Group Programmation: Program a new group in the pixels. PartDescriptionValues TitleTitle of the Menu Target GroupGroup to program on pixels1 → 31 Config Line 1Push the corresponding button to increase the target group Config Line 2Push the corresponding button to decrease the target group RF Out ON/OFF Push the corresponding button to Start/Stop the RF SendingON/OFF Wave Node - User Manual Rev08 2. Group Show: Used to determine the group of a pixel. Only the pixels with the chosen group will react and display green. PartDescriptionValues TitleTitle of the Menu Target GroupGroup of pixels that will flash green1 → 31 Config Line 1Push the corresponding button to increase the target group Config Line 2Push the corresponding button to decrease the target group RF Out ON/OFF Push the corresponding button to Start/Stop the RF SendingON/OFF Wave Node - User Manual Rev09 3. Revision: Used to check the firmware version of the pixels. Pixels will flash white to acknowledge the command and will flash green if the version is correct. PartDescriptionValues TitleTitle of the Menu Target RevThe pixels with targeted firmware revision will flash green1.1 → 63.63 Config Line 1Push the corresponding button to increase the target group Config Line 2Push the corresponding button to decrease the target group RF Out ON/OFF Push the corresponding button to Start/Stop the RF SendingON/OFF Wave Node - User Manual Rev010 4. White: Send white color for the pixels to display. Useful to verify if all three color of the RGB LEDs are working. PartDescriptionValues TitleTitle of the Menu BrightnessThe brightness of the color to display25, 50, 75, 100 % Config Line 1Push the corresponding button to increase the brightness Config Line 2Push the corresponding button to decrease the brightness RF Out ON/OFF Push the corresponding button to Start/Stop the RF SendingON/OFF Wave Node - User Manual Rev011 5. RF Color: Can send a series of RGB colors or a Color Wheel with impact mode. The Mode Color can be configure through the next Menu: PartDescriptionValues TitleTitle of the Menu Selection ArrowShow the selected Mode (with the status LED) Config Line 1 / Mode Color Push the corresponding button to select color mode Config Line 2 / Mode Impact Push the corresponding button to select impact Mode RF Out ON/OFFPush the corresponding button to Start/Stop the RF Sending ON/OFF Wave Node - User Manual Rev012 6. Config RF (5): Configure the “RF Color” Menu for the color Mode. Color, Bright and Time can be configure. PartDescriptionValues TitleTitle of t…

Text truncated - open the document above for the full version.

Eski Inc. (2022.10.09) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: CONFIDENTIALITY REQUEST FOR (WaveNode (Node RF) / WaveNode (Node RF) / FCC ID: 2ADS4-WAVENODE) To Whom It May Concern: This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the Exhibits Long-Term Confidentiality Short-Term Confidentiality NOTE 2 ID Label/Location No No Attestation Statement No No External Photos No ☐ Block Diagram ☒ ☐ Schematics ☒ ☐ Test Report No No Test Setup Photos No ☐ User’s Manual ☐ NOTE 1 ☐ Internal Photos ☐ NOTE 1 ☐ Parts List / Tune Up ☐ ☐ RF Exposure Info No No Operational Description ☒ ☐ Cover Letter(s) No No SDR Software / Security Info ☐ No required to be submitted with this application be permanently withheld from public review. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Please contact me if there is any information you may need. Sincerely, Signature: Name: Merwan GACEMI Title: Hardware development Team Lead

Eski Inc. (2022.10.09) Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize (Shenzhen CTB Testing Technology Co., Ltd.) to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Signature: Name: Merwan GACEMI Title: Hardware development Team Lead

External Photos ANT ANT

Label Location

Internal Photos

Description: 868-928MHz Swivel Type dipole antenna PART NUMBER: W1063/ W1063M Series: Stick Antenna Issue: 1837 In the effort to improve our products, we reserve the right to make changes judged to be necessary. CONFIDENTIAL AND PROPRIETARY INFORMATION This document contains confidential and proprietary information ofPulse Electronics, Inc. (Pulse) and is protected by copyright, trade secret and other state and federal laws. Its receipt or possession does not convey any rights to reproduce, disclose its contents, or to manufacture, use or sell anything it may describe. Reproduction, disclosure or use without specific written authorization of Pulse is strictly forbidden. For more information: Pulse Worldwide HeadquartersPulse/Larsen AntennasEurope HeadquartersPulse (Suzhou) Wireless Products Co, Inc. 15255 Innovation Drive #100Pulse GmbH & Do, KG99 HuoJuRoad(#29 Bldg,4 th Phase San Diego, CA 92128Vancouver, WA 98683Zeppelinstrasse15Suzhou New District USAUSAHerrenberg, Germany Jiangsu Province, Suzhou 215009 PR China Tel:1-858-674-8100Tel: 1-360-944-7551 - Tel: 49 7032 7806 0 Tel: 86 512 6807 9998 18110 SE 34 th St Bldg2 Suite 250 Features: Applications: All dimensions are in mm •Frequency 868-928MHz •Gain 1dBi •Efficiency 70% •Length 195mm straight •Connectors: •W1063 RP-SMA Male •W1063M SMA Male •RoHS Compliant •Indoor use •868MHz and 915MHz ISM band radios •IoT devices •Security •Sensors •Monitoring 1 Issue: 1837 In the effort to improve our products, we reserve the right to make changes judged to be necessary. CONFIDENTIAL AND PROPRIETARY INFORMATION This document contains confidential and proprietary information ofPulse Electronics, Inc. (Pulse) and is protected by copyright, trade secret and other state and federal laws. Its receipt or possession does not convey any rights to reproduce, disclose its contents, or to manufacture, use or sell anything it may describe. Reproduction, disclosure or use without specific written authorization of Pulse is strictly forbidden. Series: Stick Antenna Description: 868-928MHz Swivel Type dipole antenna PART NUMBER: W1063/ W1063M 2 Frequency 863-928 MHz NominalImpedance50 VSWR 2 Maximum Radiation PatternOmni Gain1 dBi Efficiency70 % PolarizationLinear Power Withstanding1 W Overall Length 195+/-2 mm Weight 23.5 g Antenna Color / Material Black Connector type W1063 RP SMA Male W1063M SMA Male IP RatingIP20, Indoor use Operating Temperature -20 °C /+65 °C Storage Temperature -30 °C /+75 °C MECHANICALSPECIFICATIONS ENVIRONMENTAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS Issue: 1837 In the effort to improve our products, we reserve the right to make changes judged to be necessary. CONFIDENTIAL AND PROPRIETARY INFORMATION This document contains confidential and proprietary information ofPulse Electronics, Inc. (Pulse) and is protected by copyright, trade secret and other state and federal laws. Its receipt or possession does not convey any rights to reproduce, disclose its contents, or to manufacture, use or sell anything it may describe. Reproduction, disclosure or use without specific written authorization of Pulse is strictly forbidden. Series: Stick Antenna Description: 868-928MHz Swivel Type dipole antenna PART NUMBER: W1063/ W1063M 3 MECHANICALDRAWING All dimensions are in mm Issue: 1837 In the effort to improve our products, we reserve the right to make changes judged to be necessary. CONFIDENTIAL AND PROPRIETARY INFORMATION This document contains confidential and proprietary information ofPulse Electronics, Inc. (Pulse) and is protected by copyright, trade secret and other state and federal laws. Its receipt or possession does not convey any rights to reproduce, disclose its contents, or to manufacture, use or sell anything it may describe. Reproduction, disclosure or use without specific written authorization of Pulse is strictly forbidden. Series: Stick Antenna Description: 868-928MHz Swivel Type dipole antenna PART NUMBER: W1063/ W1063M 4 TEST SETUP Z X Y Issue: 1837 In the effort to improve our products, we reserve the right to make changes judged to be necessary. CONFIDENTIAL AND PROPRIETARY INFORMATION This document contains confidential and proprietary information ofPulse Electronics, Inc. (Pulse) and is protected by copyright, trade secret and other state and federal laws. Its receipt or possession does not convey any rights to reproduce, disclose its contents, or to manufacture, use or sell anything it may describe. Reproduction, disclosure or use without specific written authorization of Pulse is strictly forbidden. Series: Stick Antenna Description: 868-928MHz Swivel Type dipole antenna PART NUMBER: W1063/ W1063M CHARTS 5 VSWR Issue: 1837 In the effort to improve our products, we reserve the right to make changes judged to be necessary. CONFIDENTIAL AND PROPRIETARY INFORMATION This document contains confidential and proprietary information ofPulse Electronics, Inc. (Pulse) and is protected by copyright, trade secret and other state and federal laws. Its receipt or possession does not convey any rights to reproduce, disclose its contents, or to manufacture, use or sell anything it may describe. Reproduction, disclosure or use without specific written authorization of Pulse is strictly forbidden. Series: Stick Antenna Description: 868-928MHz Swivel Type dipole antenna PART NUMBER: W1063/ W1063M CHARTS 6 Efficiency(%) Issue: 1837 In the effort to improve our products, we reserve the right to make changes judged to be necessary. CONFIDENTIAL AND PROPRIETARY INFORMATION This document contains confidential and proprietary information ofPulse Electronics, Inc. (Pulse) and is protected by copyright, trade secret and other state and federal laws. Its receipt or possession does not convey any rights to reproduce, disclose its contents, or to manufacture, use or sell anything it may describe. Reproduction, disclosure or use without specific written authorization of Pulse is strictly forbidden. Series: Stick Antenna Description: 868-928MHz Swivel …

Text truncated - open the document above for the full version.

FCC §15.247 (i), §2.1091 – RF Exposure FCC ID: 2ADS4-WAVENODE Applied procedures / limit According to FCC §15.247(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm 2 ) Averaging Time |E| 2 ,|H| 2 or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 Note: ƒ is frequency in MHz * = Power density limit is applicable at frequencies greater than 100 MHz Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm 2 ) Averaging Time |E| 2 ,|H| 2 or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz * = Plane-wave equivalent power density MPE PREDICTION Predication of MPE limit at a given distance, Equation from OET Bulletin 65, Edition 97-01 Where: S = power density P = power input to antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna,R=20cm Test Result of RF Exposure Evaluation Modes& Channel Freq. (MHz) Tune up Produce power Maximu m peak output power (dBm) Output power to antenna (mW) Antenna Gain (numeric) Power Density (S) (mW/ cm2) Limit (mW / cm2 ) Result 915 6±1 7 5.0119 1.2589 (1dBi) 0.00126 1 Pass

S henzhen CTB Testing Technology Co., Ltd. Report No.: CTB220926011RF Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 1 of 30 TEST REPORT Compiled by: Reviewed by: Approved by: Chen Zheng Arron Liu Bin Mei / Director Note: If there is any objection to the inspection results in this report, please submit a written report to the company within 15 days from the date of receiving the report. The test report is effective only with both signature and specialized stamp. This result(s) shown in this report refer only to the sample(s) tested. Without written approval of Shenzhen CTB Testing Technology Co., Ltd. this report can’t be reproduced except in full. The tested sample(s) and the sample information are provided by the client. “*” indicates the testing items were fulfilled by subcontracted lab. “#” indicates the items are not in CNAS accreditation scope. Product Name: WaveNode (Node RF) FCC ID: 2ADS4-WAVENODE Trademark: ESKI inc. Model Number: WaveNode (Node RF) Prepared For: Eski Inc. Address: 103 Louvain O, Montréal, QC J6K 5C2, Canada Manufacturer: Inspi Technology Co., Ltd. Address: Office: Room 703/726, HuaFeng Yu'An Business Building, District 45 of Ban'An, Shenzhen, China Factory: 2nd Floor, Building E, Huafeng Gaoxin Industrial Park, Shajing Street, Bao'an District, Shenzhen City, China. Prepared By: Shenzhen CTB Testing Technology Co., Ltd. Address: Floor 1&2, Building A, No. 26 of Xinhe Road, Xinqiao Community, Xinqiao Street, Baoan District, Shenzhen, Guangdong, China. Sample Received Date: Aug. 3, 2022 Sample tested Date: Aug. 3, 2022 to Sep. 26, 2022 Issue Date: Sep. 26, 2022 Report No.: CTB220926011RF Te s t Standards FCC Part15.247 ANSI C63.10:2013 Test Results PA SS Remark: This is 915MHz radio test report. Shenzhen CTB Testing Technology Co., Ltd. Report No.: CTB220926011RF Report Tel: 4008-707-283 Web: http://www.ctb-lab.net Page 2 of 30 TABLE OF CONTENT Test Report Declaration Page 1. VERSION .......................................................................... 3 2. TEST SUMMARY ................................................................... 4 3. MEASUREMENT UNCERTAINTY ..................................................... 5 4. PRODUCT INFORMATION AND TEST SETUP ......................................... 6 4.1 Product Information ................................................................... 6 4.2 Test Setup Configuration ............................................................... 6 4.3 Support Equipment.................................................................... 6 4.4 Channel List ......................................................................... 7 4.5 Test Mode ........................................................................... 7 4.6 Test Environment ..................................................................... 7 5. TEST FACILITY AND TEST INSTRUMENT USED ....................................... 8 5.1 Test Facility .......................................................................... 8 5.2 Test Instrument Used .................................................................. 8 6. AC POWER LINE CONDUCTED EMISSION ............................................. 10 6.1 Block Diagram Of Test Setup .......................................................... 10 6.2 Limit ............................................................................... 10 6.3 Test procedure ...................................................................... 10 6.4 Test Result ......................................................................... 12 7. RADIATED SPURIOUS EMISSION ................................................... 14 7.1 Block Diagram Of Test Setup .......................................................... 14 7.2 Limit ............................................................................... 14 7.3 Test procedure ...................................................................... 15 7.4 Test Result ......................................................................... 16 8. BAND EDGE AND RF COUNDUCTED SPURIOUS EMISSIONS .......................... 19 8.1 Block Diagram Of Test Setup .......................................................... 19 8.2 Limit ............................................................................... 19 8.3 Test procedure ...................................................................... 19 8.4 Test Result ......................................................................... 20 9. COUDUCTED OUTPUT POWER ..................................................... 22 9.1 Block Diagram Of Test Setup .......................................................... 22 9.2 Limit ............................................................................... 22 9.3 Test procedure ...................................................................... 22 9.4 Test Result ......................................................................... 23 10. 6DB OCCUPIED BANDWIDTH ...................................................... 24 10.1 Block Diagram Of Test Setup ......................................................... 24 10.2 Limit .............................................................................. 24 10.3 Test procedure ..................................................................... 24 10.4 Test Result ........................................................................ 24 11. POWER SPECTRAL DENSITY ...................................................... 26 11.1 Block Diagram Of Test Setup ......................................................... 26 11.2 Limit .............................................................................. 26 11.3 Test procedure ..................................................................... 26 11.4 Test Result ........................................................................ 26 12. ANTENNA REQUIREMENT ......................................................... 28 13. EUT TEST SETUP PHOTOGRAPHS ...............................…

Text truncated - open the document above for the full version.

Radiated Emission Below 1G Above 1G Conducted emissions