2ADTG-DVRC320RCAR DASH CAM

Advanced Dash Cam DVR-C320R DVR-C320S RCV-C320 • OWNER’S MANUAL Please read before using this equipment. • MODE D’EMPLOI Veuillez lire avant d’utiliser cet appareil. • BEDIENUNGSANLEITUNG Lesen Sie diese Bedienungsanleitung bitte vor Gebrauch des Gerätes. • MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. • ISTRUZIONI PER L’USO Si prega di leggere prima di utilizzare il attrezzatura. • РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ Прочтите настоящее руководство перед началом использования оборудования. FOR CAR USE ONLY/ POUR APPLICATION AUTOMOBILE UNIQUEMENT/ NUR FÜR AUTOMOBIL GEBRAUCH/ PARA USO EN AUTOMÓVILES/ SOLO PER L’UTILIZZO IN AUTOMOBILE/ ТОЛЬКО ДЛЯ ИСПОЛЬЗОВАНИЯ В АВТОМОБИЛЯХ FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. •This appliance and its antenna must not be co-located or operation in conjunction with any other antenna or transmitter. •A minimum separation distance of 20cm must be maintained between the antenna and the person for this appliance to satisfy the RF exposure requirements. FCC CAUTION : Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void your authority to operate the equipment. FCC ID: 2ADTG-DVRC320R Information to user : RSS-247 This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Please be cautioned the changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Notice: Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. IC: 12594A-DVRC320R Avant d’utiliser le produit À propos de ce produit Ce produit enregistre des vidéos pendant le fonctionnement du véhicule. Utilisez cet appareil seulement à des fins de documentation pour les enquêtes d’incidents ou d’accidents de la route. Il n’existe aucune garantie que ce produit enregistrera ou effectuera le traitement des données en nuage pour tous les événements. Le produit pourrait ne pas enregistrer les accidents ayant un impact insuffisant pour activer le capteur d’impact, ou encore les accidents ayant un très grand impact causant une déviation de la tension électrique de la batterie du véhicule. L’enregistrement vidéo commence seulement à partir du moment où le produit est entièrement en fonction (activé). Pour vous assurer que tous les événements concernant le véhicule sont enregistrés, attendez que le produit ait terminé de s’activer après l’avoir allumé, puis commencez à conduire. THINKWARE n’est aucunement responsable de toute perte résultant d’un accident ni de fournir du soutien, quel qu’il soit, en lien avec les conséquences d’un accident. Selon la configuration ou les conditions de fonctionnement du véhicule, par exemple l’installation de dispositifs de verrouillage à distance des portes ou les réglages de l’unité de contrôle électronique ou du système de surveillance de la pression des pneus, certaines fonctions du produit pourraient ne pas être prises en charge et différentes versions du logiciel peuvent avoir des effets sur le rendement ou les fonctions du produit. À propos du guide de l’utilisateur L’information présentée dans ce guide est sujette à modification quand le fabricant met à jour sa politique de service. Ce guide de l’utilisateur est conçu pour les modèles THINKWARE DVR-C320R seulement et peut comporter des erreurs techniques ou de rédaction ou des omissions. Droits d’auteur Tous les droits portant sur le contenu et les cartes du présent guide sont réservés par THINKWARE et protégés selon les lois sur la propriété intellectuelle. Toute copie, modification, publication ou distribution du présent guide sans une autorisation écrite de THINKWARE est interdite et sujette à des poursuites criminelles. Marques de commerce déposées THINKWARE DVR-C320R est une marque déposée de THINKWARE. Les autres logos de produits et noms de services apparaissant dans le présent guide sont des marques de commerce de leurs entreprises respectives. Énoncé FCC Cet appareil est conforme à la partie 15 des Règles de la FCC. Son utilisation est assujettie aux deux conditions suivantes : (1) Cet appareil ne doit causer aucune interférence nuisible et (2) …

Text truncated - open the document above for the full version.

THINKWARE CORPORATION A, 9FL, Samhwa Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do,South Korea Date: Date: July 07, 2020 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern: I, the undersigned, hereby authorize Young-Jin, Lee of KES Co., Ltd. and hereafter referred to as KES Co., Ltd., to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Young-Jin, Lee of KES Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing KES Co., Ltd. as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; THINKWARE CORPORATION A, 9FL, Samhwa Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do,South Korea h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Kyuhwa Lee / Deputy General Manager THINKWARE CORPORATION REMARK: 1. This authorization letter will be sent along with your application when filing with the Certification Division. 2. Please follow the format and type it on company letterhead and send original to us. 3. Authorized signature must be in agreement with grantee code contact in FCC database.

Supplier’s Declaration of Conformity 47 CFR § 2.1077 Compliance Information Product Description: CAR DASH CAM Model/Brand Name: DVR-C320R Variant Model: - FCC Rule Part(s): FCC 47CFR Part 15 Subpart B Class B Part 15.107 & Part 15.109 Applicant: THINKWARE CORPORATION Applicant Address: A, 9FL., Samwhan Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, South Korea Applicant Telephone No.: +82-10-2320-7248 Manufacturer THINKWARE CORPORATION Manufacturer Address: A, 9FL., Samwhan Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, South Korea Test Report Reference No.: KES-EM-20T0392 FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible Party (U.S Contact Information) Name: ALPINE ELECTRONICS OF AMERICA, INC. Address: 1500 Atlantic Boulevard, Auburn Hills, Michigan 48326, USA Telephone No. +1-800-257-4631 Authorized Party (Korea Contact person Information) Signature: Name: Kyuhwa-Lee

THINKWARE CORPORATION DATE: July 15, 2020 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Attn: Director of Certification SUBJECT: THINKWARE CORPORATION FCC ID: 2ADTG-DVRC320R Gentlemen: 1)No hardware design changes are made on the module except the Host device uses the different antennas from those of the modules and disabled below Table 1 related to WiFi band by the software, But for other bands the software no any changed to increase the RF output power of the module. The original modular reports (report number : EC1905007RI03, EC1905007RI04) are submitted to represent the compliance regarding FCC Part 15C/15E conducted RF testing items of the host device. The FCC Part 15C/15E radiated RF testing items are tested on this host device, and the test reports are submitted additionally. Table 1 - Equipment Description Modules Original Grants: Host Device Model: WIFI+BT Module Model: 8223A-SR FCC ID: 2AATL-8223A-SR CAR DASH CAM Model: DVR-C320R Frequency Range: BLE : 2402 ~ 2480 MHz Not used 802.11b/g/n(HT20) : 2412 ~ 2462 MHz 802.11b/g/n(HT20) : 2412 ~ 2462 MHz 802.11n(HT40) : 2422 ~ 2452 MHz 802.11n(HT40) : 2422 ~ 2452 MHz 802.11a: 5180~5240 MHz, 5745~5825 MHz Not used 802.11n(HT40) : 5190~5230 MHz, 5755~5790 MHz Not used 802.11ac(VHT80):5210 MHz, 5775 MHz Not used Sincerely Yours, Kyuhwa Lee / Deput y General Manager THINKWARE CORPORATION

United States Representative Letter of Attestation United States Representative Company Name : ALPINE ELECTRONICS OF AMERICA, INC. Address : 1500 Atlantic Boulevard, Auburn Hills, Michigan 48326, USA Telephone Number : +1-800-257-4631 This letter is to confirm that we have accepted the responsibility to act as United States Representative on behalf of THINKWARE CORPORATION as noted below. Applicant Company Name : THINKWARE CORPORATION Contact Name : Kyuhwa Lee Address : A, 9FL., Samwhan Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, South Korea Telephone Number : +82-10-2320-7248 Fax Number : +82-2-589-9100 E-mail : [email protected] Product / Model name : CAR DASH CAM / DVR-C320R Data of issuance : Date: July 14, 2020 Signature : Signed by (printed name): Kyuhwa Lee

FCC ID : 2ADTG-DVRC320R IC : 12594 A-DVRC320R Page 1 of 3 External photos FCC ID : 2ADTG-DVRC320R IC : 12594 A-DVRC320R Page 2 of 3 External photos FCC ID : 2ADTG-DVRC320R IC : 12594 A-DVRC320R Page 3 of 3 External photos

The device is so small that it is not practicable to place the statement specified under 15.19 statement request, the information required by this paragraph shall be placed in a Prominent location in the User’s Manual.

FCC ID : 2ADTG-DVRC320R IC : 12594 A-DVRC320R Page 1 of 3 Internal photos GPS Antenna ChipAntenna FCC ID : 2ADTG-DVRC320R IC : 12594 A-DVRC320R Page 2 of 3 Internal photos FCC ID : 2ADTG-DVRC320R IC : 12594 A-DVRC320R Page 3 of 3 Internal photos

FCC ID: 2ADTG-DVRC320R IC : 12594A-DVRC320R RF exposure According to FCC part 1.1310 : The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in § 1.1307(b) Limits for Maximum Permissible Exposure (MPE) f= frequency in ㎒ Friis transmission formula: Pd = (Pout×G)/(4×pi×R 2 ) Where, Pd = power density in ㎽/㎠ Pout = output power to antenna in ㎽ G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd the limit of MPE, 1 ㎽/㎠. If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. Results - Worst case WIFI (2.4G) Operation mode Max tune-up Average power (㏈m) Antenna gain (㏈i) Power density at 20 ㎝(㎽/㎠) Limit (㎽/㎠) 802.11b SISO 18.00 2.19 0.020784 1 802.11g SISO 16.50 2.19 0.014714 1 802.11n(HT20) SISO 16.50 2.19 0.014714 1 802.11n(HT40) SISO 16.50 2.19 0.014714 1 Frequency range (㎒) Electric field strength(V/m) Magnetic field strength (A/m) Power density (㎽/㎠) Average time (A) Limits for Occupational / Control Exposures 300 – 1 500 -- -- f/300 6 1 500 - 100000 -- -- 5 6 (B) Limits for General Population / Uncontrol Exposures 300 – 1 500 -- -- f/1500 6 1 500 – 100 000 -- -- 1 30 FCC ID: 2ADTG-DVRC320R IC : 12594A-DVRC320R RF exposure According to RSS-Gen 3.2: the requirements in Radio Standards Specification RSS-102, Radio Frequency (RF) Exposure Compliance of Radio communication Apparatus (All Frequency Bands), shall be met. INDUSTRY CANADA EXEMPTION RF exposure evaluation is required if the separation distance between the user and/or bystander and the device’s radiating element is greater than 20 ㎝, except when the device operates as follows: At or above 300 ㎒ and below 6 ㎓ and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1.31 × 10 -2 ƒ 0.6834 W (adjusted for tune-up tolerance), where ƒ is in ㎒; Results - Worst case Band Operation mode Conducted Power (dBm) Ant Gain (dBi) EIRP Limit (dBm)(W) 802.11b SISO 18.002.1920.190.104 2.684 802.11g SISO 16.50 2.1918.69 0.074 2.684 802.11n(HT20) SISO 16.50 2.1918.69 0.074 2.684 802.11n(HT40) SISO 16.50 2.1918.69 0.074 2.684

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1712035FV00 FCC ID: 2AATL-8223A-SR Page 2 of 48 Table of Contents 1. GENERAL INFORMATION ................................................................................................ 5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST.................................................................... 5 1.2 RELATED SUBMITTAL(S) / GRANT (S) ................................................................................................ 5 1.3 TEST METHODOLOGY....................................................................................................................... 8 1.4 EQUIPMENT MODIFICATIONS............................................................................................................ 8 1.5 SUPPORT DEVICE............................................................................................................................ 8 1.6 TEST FACILITY AND LOCATION.......................................................................................................... 9 1.7 SUMMARY OF TEST RESULTS......................................................................................................... 10 2. SYSTEM TEST CONFIGURATION.................................................................................. 11 2.1 EUT CONFIGURATION.................................................................................................................... 11 2.2 SPECIAL ACCESSORIES.................................................................................................................. 11 2.3 DESCRIPTION OF TEST MODES....................................................................................................... 11 2.4 EUT EXERCISE.............................................................................................................................. 11 3. CONDUCTED EMISSIONS TEST .................................................................................... 12 3.1 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)................................................................... 12 3.2 TEST CONDITION........................................................................................................................... 12 3.3 MEASUREMENT RESULTS............................................................................................................... 12 4. MAX. CONDUCTED OUTPUT POWER........................................................................... 15 4.1 MEASUREMENT PROCEDURE......................................................................................................... 15 4.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)................................................................... 15 4.3 MEASUREMENT RESULTS............................................................................................................... 15 5. 6DB&20DB BANDWIDTH ................................................................................................ 17 5.1 MEASUREMENT PROCEDURE......................................................................................................... 17 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)................................................................... 17 5.3 MEASUREMENT RESULTS............................................................................................................... 17 6. POWER SPECTRAL DENSITY ....................................................................................... 25 6.1 MEASUREMENT PROCEDURE......................................................................................................... 25 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)................................................................... 25 6.3 MEASUREMENT RESULTS............................................................................................................... 25 7. BAND EDGE AND CONDUCTED SPURIOUS EMISSIONS ........................................... 33 7.1 REQUIREMENT AND MEASUREMENT PROCEDURE........................................................................... 33 7.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)................................................................... 33 7.3 MEASUREMENT RESULTS............................................................................................................... 33 Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1712035FV00 FCC ID: 2AATL-8223A-SR Page 3 of 48 8. RADIATED SPURIOUS EMISSIONS AND RESTRICTED BANDS ................................ 41 8.1 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)................................................................... 41 8.2 MEASUREMENT PROCEDURE......................................................................................................... 42 8.3 LIMIT.............................................................................................................................................. 43 8.4 MEASUREMENT RESULTS ..................................................................................................... 43 9. ANTENNA APPLICATION ............................................................................................... 47 9.1 ANTENNA REQUIREMENT................................................................................................................ 47 9.2 MEASUREMENT RESULTS............................................................................................................... 47 10. TEST EQUIPMENT LIST................................................................................................ 48 Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1712035FV00 FCC ID: 2AATL-8223A-SR Page 4 of 48 Revision History of This Test Report Report Number Description Issued Date NTC1712035FV00 Initial Issue 2017-12-06 Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1712035FV00 FCC ID: 2AATL-8223A-SR Page 5 of 48 1. GENERAL INFORMATION 1.1 Product Description f…

Text truncated - open the document above for the full version.

KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-RF-20T0113 Page (2 ) of (50) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 Revision history Revision Date of issue Test report No. Description - 2020.07.07 KES-RF-20T0113 Initial KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-RF-20T0113 Page (3 ) of (50) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 TABLE OF CONTENTS 1. General information ................................................................................................................................................... 4 1.1. EUT description ........................................................................................................................................ 4 1.2. Test configuration ...................................................................................................................................... 4 1.3. Device modifications ................................................................................................................................. 4 1.4. Accessory information .............................................................................................................................. 4 1.5. Measurement results explanation example ................................................................................................ 5 1.6. Measurement Uncertainty ......................................................................................................................... 5 1.7. Frequency/channel operations ................................................................................................................... 5 1.8. Worst case data rate ................................................................................................................................... 6 2. Summary of tests ........................................................................................................................................................ 7 3. Test results ...................................................................................................................................................................... 8 3.1. Output power ....................................................................................................................................................... 8 3.2. Radiated restricted band and emissions ................................................................................................... 11 Appendix A. Measurement equipment ......................................................................................................................... 49 Appendix B. Test setup photos ..................................................................................................................................... 50 KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-RF-20T0113 Page (4 ) of (50) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 1. General information Applicant: THINKWARE CORPORATION Applicant address: A, 9FL, Samwhan Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, South Korea Test site: KES Co., Ltd. Test site address: 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea 473-21, Gayeo-ro, Yeoju-si, Gyeonggi-do, Korea Test Facility FCC Accreditation Designation No.: KR0100, Registration No.: 444148 ISED Registration No.: 23298 FCC/IC rule part(s): 15.247 / RSS-247 FCC ID: 2ADTG-DVRC320R IC Certification 12594A-DVRC320R Test device serial No.: Production Pre-production Engineering 1.1. EUT description Equipment under test CAR DASH CAM Frequency range 2 412 ㎒ ~ 2 462 ㎒ (11b/g/n_HT20) 2 422 ㎒ ~ 2 452 ㎒ (11n_HT40) Model: DVR-C320R Modulation technique DSSS, OFDM Number of channels 2 412 ㎒ ~ 2 462 ㎒ (11b/g/n_HT20) : 11ch 2 422 ㎒ ~ 2 452 ㎒ (11n_HT40) : 9 ch Antenna specification Antenna type(2.4㎓ WIFI) : Chip antenna, Peak gain : 2.19 ㏈i Power source DC 12 V H/W version V3.0(PP) S/W version v0.17.00 1.2. Test configuration The THINKWARE CORPORATION // DVR-C320R // FCC ID: 2ADTG-DVRC320R // IC : 12594A- DVRC320R was tested according to the specification of EUT, the EUT must comply with following standards and KDB documents. FCC Part 15.247 ISED RSS-247 Issue 2 and RSS-Gen Issue 5 KDB 558074 D01 v05 r02 ANSI C63.10-2013 1.3. Device modifications N/A 1.4. Accessory information N/A KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-RF-20T0113 Page (5 ) of (50) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 1.5. Measurement results explanation example For all conducted test items : The offset leve…

Text truncated - open the document above for the full version.

KES Co., Ltd. 3701, 40, Simin-daero 365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Report No.: KES-RF-20T0113 Page (50 ) of (50) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The results shown in this test report refer only to the sample(s) tested unless otherwise stated. The authenticity of the test report, contact [email protected] KES-QP-7081-06 Rev. 7 KES A4 Appendix B. Test setup photos The end of test report. Radiated Blank