2ADTG-U1000PLUSTHINKWARE DASH CAM

User Guide This product records videos while the vehicle is operating. Read and follow the instructions in this guide to properly use and maintain the product. Derivative model : XD350, D4K64DM, D4K32DM, DC-U2-FG U1000 PLUS Before using the product About the product This product records videos while the vehicle is operating. Use this product only for reference when investigating incidents or road accidents. This product is not guaranteed to record all events. The device may not record accidents with impacts that are too minor to activate the impact sensor or accidents with massive impacts that cause the vehicle’s battery voltage to deviate. Video recording does not begin until the product is completely turned on (booted up). To ensure that all vehicle events are recorded, wait until the product is completely booted up after turning it on, and then begin operating the vehicle. THINKWARE is not responsible for any loss caused by an accident, nor is it responsible for providing any support regarding the outcome of an accident. Depending on the vehicle's configuration or operating conditions, such as the installation of remote door lock devices, ECU settings, or TPMS settings, some product features may not be supported, and different firmware versions may influence the product's performance or features. About the user guide The information provided in the guide may change when the manufacturer updates its service policy. This user guide is intended for THINKWARE XD350 models only, and it may contain technical errors, editorial errors, or missing information. Copyrights All rights for the content and maps in this guide are reserved by THINKWARE and are protected under copyright laws. All unauthorized duplication, revision, publication, or distribution of this guide without written consent from THINKWARE is prohibited and is eligible for criminal charges. Registered trademarks THINKWARE XD350 is a registered trademark of THINKWARE. Other product logos and service names in this guide are trademarks of the relevant companies. Turning voice recording ON or OFF Some jurisdictions may prohibit recoding voice in the vehicle or may require that all passengers have knowledge of the recording and provide consent before you record voice in the vehicle. It is your responsibility to know and follow all laws and restrictions for your jurisdiction. The device can record voice using the integrated microphone while recording video. Voice recording is ON by default. Please refer to the manual to turn voice recording on or off at any time. 3 Contents Safety information 4 1.Product overview 6 1.1 Included items 6 1.1.1 Standard items 6 1.1.2 Accessories (sold separately) 6 1.2 Part names 7 1.2.1 Front camera (main unit) - front view 7 1.2.2 Front camera (main unit) - rear view 8 1.2.3 Rear camera (optional) 9 1.3 Removing and inserting the memory card 9 2.Installing the product 10 2.1 Installing the front camera (main unit) 10 2.1.1 Selecting an installation location 10 2.1.2 Securing the product 10 2.1.3 Connecting the power cable 12 2.2 Installing the rear camera (optional) 15 2.2.1 Selecting an installation location 15 2.2.2 Securing the rear camera 16 2.2.3 Connecting the rear camera cable 17 2.3 Installing the RADAR module (optional) 18 3.Using recording features 19 3.1 Turning the product on or off 19 3.2 Learning about file storage locations 19 3.3 Using the continuous recording feature 19 3.4 Recording manually 20 3.5 Using the SOS recording feature 20 3.6 Using parking mode 21 3.7 Using the Super Night Vision 3.0 22 3.8 Using the road safety features 22 4.Using the mobile viewer 23 4.1 Connect the product to a smartphone 23 4.2 Viewing the mobile viewer screen layout 23 5.Using THINKWARE CONNECTED 24 5.1 Connecting the product to THINKWARE CONNECTED 25 6.Using the PC viewer 26 6.1 System requirements 26 6.2 Learning about the PC viewer 26 6.2.1 Downloading the PC viewer 26 6.2.2 Installing the PC viewer 26 6.2.3 PC viewer screen layout 27 6.2.4 Playing recorded videos on the PC viewer 28 7.Settings 29 7.1 Managing the memory card 29 7.2 Setting the Camera 29 7.3 Setting recording features 30 7.4 Setting road safety features 31 7.5 Configuring the system settings 31 8.Upgrading the firmware 32 9.Troubleshooting 33 10. Specifications 34 4 Safety information Read the following safety information to properly use the product. Safety symbols in this guide "Warning" - Indicates a potential hazard which, if not avoided, may result in injury or death. "Caution" - Indicates a potential hazard which, if not avoided, may result in minor injury or property damage. "Note" - Provides useful information to help users better utilize the product's features. Safety information for proper use Driving and product operation • Do not operate the product while driving a vehicle. Distraction while driving may cause accidents and result in injury or death. • Install the product in places where the driver's view is not obstructed. Obstruction of the driver’s vision may cause accidents and result in injury or death. Check with your state and municipal laws before mounting the product to the windshield. Power supply • Do not operate or handle the power cable with wet hands. Doing so may result in electrocution. • Do not use damaged power cables. Doing so may result in electrical fire or electrocution. • Keep the power cable away from all heat sources. Failure to do so may cause the power cord insulation to melt, resulting in electrical fire or electrocution. • Use the power cable with the correct connector and make sure the power cable is connected securely and is firmly in place. Failure to do so may result in electrical fire or electrocution. • Do not modify or cut the power cable. Also, do not place heavy objects on the power cable or pull, insert, or bend the power cable using excessive force. Doing so may result in electrical fire or electrocution. • Use only genuine accessories from THINKWARE or an authorized THINKWARE dealer…

Text truncated - open the document above for the full version.

Certification Attestation Statements Attn: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: July 9, 2024 FCC ID: 2ADTG-U1000PLUS Ref: Attestation Statements Part 2.911(d)(5)(i) Filing THINKWARE CORPORATIONcertifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the currentCovered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Additional Explanation: (Please add if applicable) : We are not applicable. Ref: Attestation Statements Part 2.911(d)(5)(ii) Filing THINKWARE CORPORATION(“the applicant”) certifies that, as of the date of the filing of this application, the applicant☐- is /▣- is not identified on theCovered List(as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing “covered” equipment. Sincerely, Signature Name:Musung, Kim. Title: Manager Company:THINKWARE CORPORATION Tel # : +82-02-589-9425 1 -The Commission’sCovered Listis published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment.https://www.fcc.gov/supplychain/coveredlist. 2 -Letters should be placed on appropriate letterhead.

Rev 1/26/2023 Attn: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: July 4, 2024 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID or Grantee Code: FCC ID : 2ADTG-U1000PLUS Applicant’s FRN : 0024149957 THINKWARE CORPORATION (“the applicant”) certifies that, as of the date of the filing of the application, Thinkware Systems USA Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. THINKWARE CORPORATION accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Thinkware Systems USA Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Thinkware Systems USA Inc. FRN: 0033574567 Address: 18019 Sky Park Circle, Suite L, Irvine, CA 92614 Contact Person: Patrick Bong Email: [email protected] Sincerely, THINKWARE CORPORATION Thinkware Systems USA Inc. Musung, Kim. Patrick Bong [Insert Applicant signature] [U.S. Agent signature]

THINKWARE CORPORATION A, 9FL., Samwhan Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, South Korea Tel: +82-2-589-9425 / Fax: +82-2-589-9600 Date: July 05, 2024 Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Chief, Certification and Engineering Bureau Industry Canada 1241 Clyde Avenue Ottawa, Ontario Canada K2C 1Y3 Regarding FCC & IC Application FCC ID : 2ADTG-U1000PLUS IC Number: 12594A-U1000PLUS We, THINKWARE CORPORATION, declare that the device does not support channel 12 ~ 13 in 2.4 GHz band. The firmware setting is not accessible by end users and/or unauthorized 3rd parties. Signature: Mr Mu Sung Kim / manager THINKWARE CORPORATION

THINKWARE CORPORATION A, 9FL., Samwhan Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, South Korea Tel: +82-2-589-9425 / Fax: +82-2-589-9600 Date: July 05, 2024 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Chief, Certification and Engineering Bureau Industry Canada 1241 Clyde Avenue Ottawa, Ontario Canada K2C 1Y3 Confidentiality Request regarding application for certification of FCC ID : 2ADTG-U1000PLUS IC Number: 12594A-U1000PLUS Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules and IC regulation, we hereby request confidential treatment of information accompanying this application as outlined below: PERMANENT Exhibit TypeFile Name Part ListPart List.pdf Schematics Diagram(s)Schematic.pdf Operation descriptionOperation description.pdf Block diagramBlock diagram.pdf And the above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Mr Mu Sung Kim / manager THINKWARE CORPORATION

THINKWARE CORPORATION A, 9FL., Samwhan Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, South Korea Tel: +82-2-589-9425 / Fax: +82-2-589-9600 Date: July 05, 2024 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Chief, Certification and Engineering Bureau Industry Canada 1241 Clyde Avenue Ottawa, Ontario Canada K2C 1Y3 FCC ID : 2ADTG-U1000PLUS IC Number: 12594A-U1000PLUS To whom it may concern: I, the undersigned, hereby authorize Young-Jin, Lee of KES Co., Ltd. and hereafter referred to as KES Co., Ltd., to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Young-Jin, Lee of KES Co., Ltd. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing KES Co., Ltd. as our agent, we still recognize that we are responsible to: a)comply with the relevant provisions of the certification program; b)make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c)make claims regarding certification only in respect of the scope for which certification has been granted; d)do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; THINKWARE CORPORATION A, 9FL., Samwhan Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, South Korea Tel: +82-2-589-9425 / Fax: +82-2-589-9600 e)upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f)use certification only to indicate the products are certified as being in conformity with specified standards; g)endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h)ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i)keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j)take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k)document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Mr Mu Sung Kim / manager THINKWARE CORPORATION REMARK: 1.This authorization letter will be sent along with your application when filing with the Certification Division. 2.Please follow the format and type it on company letterhead and send original to us. 3.Authorized signature must be in agreement with grantee code contact in FCC database.

FCC ID : 2ADTG-U1000PLUS IC Number: 12594A-U1000PLUS Page 1 of 3 External photos FCC ID : 2ADTG-U1000PLUS IC Number: 12594A-U1000PLUS Page 2 of 3 FCC ID : 2ADTG-U1000PLUS IC Number: 12594A-U1000PLUS Page 3 of 3 Blank

FCC ID : 2ADTG-U1000PLUS IC : 12594A-U1000PLUS Page 1 of 1 Label & Label Location The device is so small that it is not practicable to place the statement specified under 15.19 statement request, the information required by this paragraph shall be placed in a prominent location in the User’s Manual.

FCC ID : 2ADTG-U1000PLUS IC Number: 12594A-U1000PLUS Page 1 of 3 Internal photos FCC ID : 2ADTG-U1000PLUS IC Number: 12594A-U1000PLUS Page 2 of 3 FCC ID : 2ADTG-U1000PLUS IC Number: 12594A-U1000PLUS Page 3 of 3 Chip Antenna

FCC ID : 2ADTG-U1000PLUS Page 1 of 1 RF exposure According to FCC part 1.1310 : The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in § 1.1307(b) Limits for Maximum Permissible Exposure (MPE) f= frequency in ㎒ Friis transmission formula: Pd = (Pout×G)/(4×pi×R 2 ) Where, Pd = power density in ㎽/㎠ Pout = output power to antenna in ㎽ G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd the limit of MPE, 1 ㎽/㎠. If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. Results Operation mode Frequency (㎒) Max Tune-up Average Power(㏈m) Antenna gain (㏈i) Power density at 20 ㎝(㎽/㎠) Limit (㎽/㎠) LE 1 Mbps 2 402 ~ 2 480 1.0 1.47 0.000 35 1 802.11b 2 412 ~ 2 462 8.0 0.001 76 802.11g 6.0 0.001 11 802.11n_HT20 4.0 0.000 70 802.11a 5 180 ~ 5 240 6.0 2.35 0.001 36 802.11n_HT20 6.0 0.001 36 802.11ac_VHT20 6.0 0.001 36 802.11n_HT40 5 190 ~ 5 230 7.0 0.001 71 802.11ac_VHT40 6.0 0.001 36 802.11ac_VHT80 5 210 7.0 0.001 71 Frequency range (㎒) Electric field strength(V/m) Magnetic field strength (A/m) Power density (㎽/㎠) Average time (A) Limits for Occupational / Control Exposures 300 – 1 500 -- -- f/300 6 1 500 - 100000 -- -- 5 6 (B) Limits for General Population / Uncontrol Exposures 300 – 1 500 -- -- f/1500 6 1 500 – 100 000 -- -- 1 30

Report No. : KES-RF240420-R1 Page54/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). Mode:802.11n_HT20_DC 24 V Distance of measurement:3 meter Channel:48 -Spurious Frequency (㎒) Level (㏈㎶) Detect mode Ant. Pol. (H/V) CF (㏈) DCF (㏈) Field strength (㏈㎶/m) Limit (㏈㎶/m) Margin (㏈) 1 045.7544.82PeakH-9.11-35.7174.0038.29 2 430.1144.54PeakV-0.30-44.2468.2023.96 Horizontal // Peak for 1㎓to 6㎓Vertical // Peak for 1㎓to 6㎓ Horizontal // Peak for 6㎓to 18㎓Vertical // Peak for 6㎓to 18㎓ Note. 1. No spurious emission were detected above 6㎓. 2. Average test would be performed if the peak result were greater than the average limit. Report No. : KES-RF240420-R1 Page55/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). Mode:802.11ac_VHT20_DC 12 V Distance of measurement:3 meter Channel:36 -Spurious Frequency (㎒) Level (㏈㎶) Detect mode Ant. Pol. (H/V) CF (㏈) DCF (㏈) Field strength (㏈㎶/m) Limit (㏈㎶/m) Margin (㏈) 1 150.7344.73PeakV-8.45-36.2874.0037.72 1 247.2345.13PeakH-7.85-37.2868.2030.92 -Band edge Frequency (㎒) Level (㏈㎶) Detect mode Ant. Pol. (H/V) CF (㏈) DCF (㏈) Field strength (㏈㎶/m) Limit (㏈㎶/m) Margin (㏈) 4 536.2943.18PeakV4.70-47.8874.0026.12 4 536.2933.15AverageV4.702.5240.3754.0013.63 4 860.1247.39PeakH6.72-54.1174.0019.89 4 860.1243.15AverageH6.722.5252.3954.001.61 4 860.1249.89PeakV6.72 -56.6174.0017.39 4 860.1242.22AverageV6.722.5251.4654.002.54 Restricted band // Horizontal // PeakRestricted band // Vertical // Peak Report No. : KES-RF240420-R1 Page56/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). Restricted band // Horizontal // AverageRestricted band // Vertical // Average Horizontal // Peak for 1㎓to 6㎓Vertical // Peak for 1㎓to 6㎓ Horizontal // Peak for 6㎓to 18㎓Vertical // Peak for 6㎓to 18㎓ Note. 1. No spurious emission were detected above 6㎓. 2. Average test would be performed if the peak result were greater than the average limit. Report No. : KES-RF240420-R1 Page57/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). Mode:802.11ac_VHT20_DC 12 V Distance of measurement:3 meter Channel:44 -Spurious Frequency (㎒) Level (㏈㎶) Detect mode Ant. Pol. (H/V) CF (㏈) DCF (㏈) Field strength (㏈㎶/m) Limit (㏈㎶/m) Margin (㏈) 1 039.2545.69PeakV-9.15-36.5474.0037.46 1 292.7245.76PeakH-7.57- 38.19 68.2030.01 Horizontal // Peak for 1㎓to 6㎓Vertical // Peak for 1㎓to 6㎓ Horizontal // Peak for 6㎓to 18㎓Vertical // Peak for 6㎓to 18㎓ Note. 1. No spurious emission were detected above 6㎓. 2. Average test would be performed if the peak result were greater than the average limit. Report No. : KES-RF240420-R1 Page58/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). Mode:802.11ac_VHT20_DC 12 V Distance of measurement:3 meter Channel:48 -Spurious Frequency (㎒) Level (㏈㎶) Detect mode Ant. Pol. (H/V) CF (㏈) DCF (㏈) Field strength (㏈㎶/m) Limit (㏈㎶/m) Margin (㏈) 1 050.2445.77PeakH-9.09-36.6874.0037.32 1 068.7445.26PeakV-8.97-36.2974.0037.71 Horizontal // Peak for 1㎓to 6㎓Vertical // Peak for 1㎓to 6㎓ Horizontal // Peak for 6㎓to 18㎓Vertical // Peak for 6㎓to 18㎓ Note. 1. No spurious emission were detected above 6㎓. 2. Average test would be performed if the peak result were greater than the average limit. Report No. : KES-RF240420-R1 Page59/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). Mode:802.11ac_VHT20_DC 24 V Distance of measurement:3 meter Channel:36 -Spurious Frequency (㎒) Level (㏈㎶) Detect mode Ant. Pol. (H/V) CF (㏈) DCF (㏈) Field strength (㏈㎶/m) Limit (㏈㎶/m) Margin (㏈) 1 893.1645.90PeakH-2.42-43.4874.0030.52 2 430.6145.55PeakV-0.30- 45.25 68.2022.95 -Band edge Frequency (㎒) Level (㏈㎶) Detect mode Ant. Pol. (H/V) CF (㏈) DCF (㏈) Field strength (㏈㎶/m) Limit (㏈㎶/m) Margin (㏈) 4 536.29 44.55PeakV4.70 - 49.2574.0024.75 4 536.2932.76AverageV4.702.5239.9854.0014.02 4 860.1246.89PeakH6.72-53.6174.0020.39 4 860.1242.87AverageH6.722.5252.1154.001.89 4 860.1249.31PeakV6.72-56.0374.0017.97 4 860.1242.98AverageV6.722.5252.2254.001.78 Restricted band // Horizontal // PeakRestricted band // Vertical // Peak Report No. : KES-RF240420-R1 Page60/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). Restricted band // Horizontal // AverageRestricted band // Vertical // Average Horizontal // Peak for 1㎓to 6㎓Vertical // Peak for 1㎓to 6㎓ Horizontal // Peak for 6㎓to 18㎓Vertical // Peak for 6㎓to 18㎓ Note. 1. No spurious emission were detected above 6㎓. 2. Average test would be performed if the peak result were greater than the average limit. Report No. : KES-RF240420-R1 Page61/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). Mode:802.11ac_VHT20_DC 24 V Distance of measurement:3 meter Channel:44 -Spurious Frequency (㎒) Level (㏈㎶) Detect mode Ant. Pol. (H/V) CF (㏈) DCF (㏈) Field strength (㏈㎶/m) Limit (㏈㎶/m) Margin (㏈) 1 039.7545.86PeakV-9.15-36.7174.0037.29 1 224.2344.87PeakH-7.99-36.8874.0037.12 Horizontal // Peak for 1㎓to 6㎓Vertical // Peak for 1㎓to 6㎓ Horizontal // Peak for 6㎓to 18㎓Vertical // Peak for 6㎓to 18㎓ Note. 1. No spurious emission were detected above 6㎓. 2. Average test would be performed if the peak result were greater than the average limit. Report No. : KES-RF240420-R1 Page62/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). Mode:802.11ac_VHT20_DC 24 V Distanc…

Text truncated - open the document above for the full version.

TEST REPORT Report No. : KES-RF240420-R1 Page1/81 KES Co., Ltd. #3002, #3503, #3701, 40, Simin-daero365beon-gil, Dongan-gu, Anyang-si,Gyeonggi-do, 14057, Republic ofKorea Tel : +82-31-425-6200, Fax : +82-31-341-3838 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). FCC & IC TEST REPORT 1. Client ○ Name : THINKWARE CORPORATION ○ Address : A, 9FL., Samwhan Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, South Korea 2. Sample Description ○ Product item : THINKWARE DASH CAM ○ Model name : U1000PLUS ○ Manufacturer etc. : THINKWARE CORPORATION 3. Date of test :2024.06.24 ~ 2024.07.04 4. Location of Test :Permanent Testing LabOn Site Testing ○ Adress : 473-21, Gayeo-ro, Yeoju-si, Gyeonggi-do, Korea 5. Test method used :Part 15 Subpart E 15.407, RSS-247 (Issue 3), RSS-Gen (Issue 5) 6. Test result :PASS The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This laboratory is not accredited for the test results marked *. This test report is not related to KOLAS accreditation. Affirmation Tested byTechnical Manager Name : Gu-Bong, Kang(Signature) Name :Yeong-Jun Cho(Signature) 2024 . 07. 09. KES Co., Ltd. Accredited by KOLAS, Republic of KOREA Report No. : KES-RF240420-R1 Page2/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). REPORT REVISION HISTORY DateTest Report No.Revision History 2024.07.05KES-RF240420Initial 2024.07.09KES-RF240420-R1 Corrected typo in limit (Maximum conducted output power, Power spectral density) : Outdoor access point -> Indoor access point This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. This document may be altered or revised by KES Co., Ltd. personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by KES Co., Ltd. will constitute fraud and shall nullify the document. Use of uncertainty of measurement for decisions on conformity (decision rule): No decision rule is specified by the standard, when comparing the measurement result with the applicable limit according to the specification in that standard. The decisions on conformity are made without applying the measurement uncertainty(“simple acceptance” decision rule, previously known as “accuracy method”). ☐ Other (to be specified, for example when required by the standard or client) Report No. : KES-RF240420-R1 Page3/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). TABLE OF CONTENTS 1.General information ................................................................................................................................... 4 1.1.EUT description .......................................................................................................................... 4 1.2.Test configuration........................................................................................................................ 4 1.3.Information about derivative model ............................................................................................ 5 1.4.Accessory information ................................................................................................................ 5 1.5.Device modifications................................................................................................................... 5 1.6.Sample calculation ..................................................................................................................... 5 1.7.Worst case data rate................................................................................................................... 5 1.8.Measurement Uncertainty .......................................................................................................... 5 1.9.Frequency/channel operations ................................................................................................... 6 2.Summary of tests ....................................................................................................................................... 7 3.Test results ................................................................................................................................................. 8 3.1.26㏈bandwidth & 99% Occupied Bandwidth .......................................................................... 8 3.2.Maximum conducted output power........................................................................................... 16 3.3.Power spectral density ............................................................................................................. 19 3.4.Frequency Stability ................................................................................................................... 25 3.5.Radiated restricted band and emissions .................................................................................. 27 3.6.Antenna Requirement............................................................................................................... 80 Appendix A. Measurement equipment.......................................................................................................... 81 Report No. : KES-RF240420-R1 Page4/81 KES-QP16-F01(00-23-01-01)KES Co., Ltd. The authenticity of this test report can be found on the verification page of our website (www.kes.co.kr). 1.General information Applicant:THINKWARE CORPORATION Applicant address:A, 9FL., Samwhan Hipex, 240, Pangyoyeok-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, South Korea Test site:KES Co., Ltd. Test site address:#3002, #3503, #3701, 40, Simin-daero365beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Republic of Korea 473-21, Gayeo-ro, Yeoju-si, Gyeonggi-do, Korea Tes…

Text truncated - open the document above for the full version.

ٛDielectric Chip Antenna Original Design Chip Antenna Data Sheet - P/N : ODBWPTR5020 - - Application Frequency Band[MHz] Bluetooth(2.4GHz WiFi) & 5GHz WiFi Bluetooth : 2400 ~ 2485 & WiFi : 5150 ~ 5825 `Dielectric Chip Antenna ■ ODBWPTR5020 Dimension B B C Chip Antenna Dimension Chip Antenna Soldering Pad Dimension PCB Soldering Land Dimension T L W A F F C EAEAAD AAAAAA D ParameterLWTABCDEF Value[mm] 5.0 ±0.1 2.0 ±0.1 1.2 ±0.1 0.60.80.41.40.70.9 Unless Specified tolerances are ± 0.05 mm `Dielectric Chip Antenna ■ Antenna Marking System ◀ BW 1 5 4 ①②③④⑤ ITEMDESCRIPTION ① Input Signal Input Signal ② Serial Bluetooth(2.4GHz WiFi) Band and 5GHz WiFi Band ③ Year Ex)1-2011,2-2012, .... , 9 - 2019, .... ④ Month 123456 JanuaryFebruaryMarchAprilMayJune 789ABC JulyAugustSeptemberOctoberNovemberDecember ⑤ Date 123456789AB 1st2nd3rd4th5th6th7th8th9th10th11th CDEFGHIJKLM 12th13th14th15th16th17th18th19th20th21th22th NOPQRSTUV 23th24th25th26th27th28th29th30th31th ■ Antenna PAD Information Via Non-Ground Region Ground Region 0.5mm feed line 1005 series 1005 series 1005 series 78 123 65 4 0.5mm feed line ◀BW154 ` Dielectric Chip Antenna ■ AutoCAD Drawing of Reference PCB Design for ODBWPTR5020 Product 1 2 3 4 5 6 7 8 …

Text truncated - open the document above for the full version.