2AEAN-WGOIITXWireless Microphone System - Transmitter

dB RX Wireless Microphone System Quickstart Guide TX TXA TXB 1 TXATXB TXATXB 2 3 4 5 0 dB RX -12 dB -24 dB RX 3s 3s 3s RX 4 Love your Wireless GO II? Share with us#rodemic rode.com Scan the QR code to find out more rodemic @ rodemic @ rodemics A Wireless GO II Transmitter & Wireless GO II Receiver Manufacturer: RØDE Microphones 107 Carnarvon St, Silverwater, 2128, Australia C M Y CM MY CY CMY K wirelessgo_II_compliance_document_01.ai 1 21/10/20 2:59 pmwirelessgo_II_compliance_document_01.ai 1 21/10/20 2:59 pm 3s 6 RX 10 s IMPORTANT SAFETY INFORMATION REGULATORY & SAFETY 1. R ead and understand the i nstr uctions and safety guide com p letely befo r e usi ng the pro d uct. 2. E nsur e bo th the instr uction m a nual and safety guide are accessible to al l users, includ i ng when passing the product on to third parties. 3. O nly use this product wit h authorised RØDE accesso ries. 4. Do no t open the product housing. T his will v o id t he warran t y 5. Refer a ll serv ice and repair to R Ø D E-ap proved servi ce personnel. Service or repair is required for products that hav e been damaged, exposed t o liquid, rain or mo isture, or do not o p erate normally. 6. Use the product only in the ways desc ribed in t he inst ruct ions. 7 . Do not use the pro duct if it was damaged during t ransportati on. 8. Keep the product away from liquids and electr icall y conductive objects that are not necessary fo r op eration . 9. Do not use any solvents o r corrosiv e clea ning agents to clean the prod uct. 10. Do no t adjust the controls of the product in an environment tha t requires y o ur attention (operating machinery, dr iving etc.). NORTH AMERICA This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device contains licence-ex- empt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L' appareil ne doit pas produire de brouillage; (2) L' appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d' en compromettre le fonctionnement. Regulatory information such as identification numbers are displayed on the Wireless GO II receiver by pressing the Gain ( and Pair (sh buttons simultaneously for three seconds. To dismiss this screen, simply press any button on the receiver. EU COMPLIANCE STATEMENT RØDE Microphones hereby declares that this wireless device is in compliance with Radio Emissions Directive 2014/53/EU. A copy of the EU Declaration of Conformity is available at http://www.rode.com/wireless/wirelessgoII. For details of EU Representative go to rode.com/distributor. Frequency Range: 2.400 – 2.4835 GHz Transmission Power: < 10mW dB SOUTH KOREA 硽疩ֵአᘏ礚Ꭳᒫ殻虻懱ԏ砺֢ྍ詽 褖ӣ㮆砺֢ྍ詽 憙ێ狒虁蘻承物ֵአ螂ଶ盳㰁疏憙ێ 憙ێ狒虁ဳ఺Ԫ殻物 Lֵአ獤楮藶ջ௳獤楮牐 LL๚笕䵇ଞ㱾犋፡蓦癷䵇犥Ӥྯॠ፡蓦癷犋ᥝ᩻螂ੜ碻牐 犵ۑሲ疤毱襎秚蘻承物 犵ۑሲ疤毱襎秚螕አ 妿ࣳୗ藨挨ݳ໒ԏ犵ۑሲ疤毱襎秚牧覍妿战 ݢ牧獍ݪ牏珶蒈౲ֵአᘏ璂犋஑඘ᛔ虋ๅ毱ሲ牏ےय़ۑሲ౲虋ๅܻ戔懯ԏ粬௔现ۑ胼牐犵 ۑሲ疤毱襎秚ԏֵአ犋஑୽段汜膠ਞ獊现ଗ硑ݳဩ蝢מ牪妿咳匍磪ଗ硑匍虡碻牧䛑缏ܨ؊ አ牧㪔硬珿ᛗ篷ଗ硑碻ො஑媣媲ֵአ牐獮殻ݳဩ蝢מ牧瞲狅襎מဩ憒ਧ֢禂ԏ篷娄襎蝢מ 牐犵ۑሲ疤毱襎秚殾盚ݳݑဩ蝢מ౲ૡ禂牏ᑀ䋊现蠴ዌአ襎ူᬊ疤௔襎秚戔猋ԏଗ硑牐 襎穥ਞ獊ፘ橕ဳ఺Ԫ殻牐 5V 0.3A CCAL19LP1800T4 EUROPE USA CANADA AUS/NZ TAIWAN POWER TA I WA N 蝢螂ݶ碻ೲӥीፅ[[޾蟴䌘 [[[ ೲ衔ӣᑁ楮牧:LUHOHVV*2,,矑硩瑊Ӥ疰䨝氥纈)&&޾,& 秂蘷蒈缛ဩ憒מ௳牐ᥝ橕樂種੽癷牧ݝ襑ೲӥ矑硩瑊Ӥጱ犨఺ೲ衔ݢܨ牐 dB dB 5 A android SC16* SC15* * Cable available seperately câble disponible séparément kabel separat erhältlich cable disponible por separado cabo disponível separadamente 歏綈支杝䲿⣘ ٕـ٦؛ךⴽ㡰׶ ݒ౸
ب߹
࠶ா੉ TXA TXB TXA + TXB L+R TXA TXB TXAL TXB R 7 TX 8 RX 9 The Apple logo and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries ID: Company Name: RØDE Microphones Model: Country of Origin: Australia JAPAN Transmitter: Reciever: Transmitter: Reciever: Transmitter: Reciever: 2AEAN-WGOIITX 2AEAN-WGOIIRX 20091-WGOIITX 20091-WGOIIRX Transmitter: Reciever: C M Y CM MY CY CMY K wirelessgo_II_compliance_document_01.ai 2 21/10/20 2:59…

Text truncated - open the document above for the full version.

RODE Microphones 107 Carnarvon Street, Silverwater, 2128. Australia Agent Authorization Company: RODE Microphones Address: 107 Carnarvon Street, Silverwater, 2128. Australia Product Name: Wireless Microphone System - Transmitter Model Number(s): Wireless GO II Transmitter Product Description: Wireless Microphone System - Transmitter We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Sep. 25, 2020 Name: Pieter Schillbeeckx Title: Head of New Product Development Company: RODE Microphones

External Photos ALL VIEW OF EUT TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT VIEW OF EUT (PORT)-1 VIEW OF EUT (PORT)-2

Internal Photos OPEN VIEW OF EUT INTERNAL VIEW-1 OF EUT INTERNAL VIEW-2 OF EUT INTERNAL VIEW-3 OF EUT INTERNAL VIEW-4 OF EUT INTERNAL VIEW-5 OF EUT INTERNAL VIEW-6 OF EUT INTERNAL VIEW-7 OF EUT Antenna 1 INTERNAL VIEW-8 OF EUT VIEW OF ADAPTER Antenna 2

RF EXPOSURE EVALUATION 1. PRODUCT INFORMATION Product Description Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter FCC ID 2AEAN-WGOIITX 2. EVALUATION METHOD According to 447498 D01 General RF Exposure Guidance v05 The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] ·[√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. Where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation 3. CALCULATION P t =5.517dBm=3.56mW The value of the Maximum output power P t is referred to the test report of the CFR47 §15.247. The result for RF exposure evaluation SAR=(3.56mW /5mm) .[√2.402(GHz)]= 1.104<3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR. 4. CONCLUSION The SAR evaluation is not required.

Page 1 of 76 FCC Test Report Report No.: AGC10232200801FE03 FCC ID : 2AEAN-WGOIITX APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Wireless Microphone System - Transmitter BRAND NAME : RODE Microphones MODEL NAME : Wireless GO II Transmitter APPLICANT : RODE Microphones DATE OF ISSUE : Sep. 25, 2020 STANDARD(S) : FCC Part 15.247 REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC10232200801FE03 Page 2 of 76 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Sep. 25, 2020 Valid Initial Release Report No.: AGC10232200801FE03 Page 3 of 76 TABLE OF CONTENTS 1. VERIFICATION OF COMPLIANCE .................................................................................................................. 5 2. GENERAL INFORMATION .............................................................................................................................. 6 2.1. PRODUCT DESCRIPTION ........................................................................................................................ 6 2.2. TABLE OF CARRIER FREQUENCYS ....................................................................................................... 6 2.3. RELATED SUBMITTAL(S)/GRANT(S) ....................................................................................................... 7 2.4. TEST METHODOLOGY ............................................................................................................................. 7 2.5. SPECIAL ACCESSORIES .......................................................................................................................... 7 2.6. EQUIPMENT MODIFICATIONS ................................................................................................................. 7 2.7. ANTENNA REQUIREMENT ....................................................................................................................... 7 3. MEASUREMENT UNCERTAINTY ................................................................................................................... 8 4. DESCRIPTION OF TEST MODES ................................................................................................................... 9 5. SYSTEM TEST CONFIGURATION ................................................................................................................ 10 5.1. CONFIGURATION OF TESTED SYSTEM ............................................................................................... 10 5.2. EQUIPMENT USED IN TESTED SYSTEM .............................................................................................. 10 5.3. SUMMARY OF TEST RESULTS .............................................................................................................. 10 6. TEST FACILITY .............................................................................................................................................. 11 7. PEAK OUTPUT POWER ................................................................................................................................ 12 7.1. MEASUREMENT PROCEDURE .............................................................................................................. 12 7.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 12 7.3. LIMITS AND MEASUREMENT RESULT .................................................................................................. 13 8. 6 DB BANDWIDTH ......................................................................................................................................... 17 8.1. MEASUREMENT PROCEDURE .............................................................................................................. 17 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 17 8.3. LIMITS AND MEASUREMENT RESULTS ............................................................................................... 17 9. CONDUCTED SPURIOUS EMISSION........................................................................................................... 21 9.1. MEASUREMENT PROCEDURE .............................................................................................................. 21 9.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................... 21 9.3. MEASUREMENT EQUIPMENT USED .................................................................................................... 21 9.4. LIMITS AND MEASUREMENT RESULT .................................................................................................. 21 10. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY ........................................................ 36 Report No.: AGC10232200801FE03 Page 4 of 76 10.1. MEASUREMENT PROCEDURE ............................................................................................................ 36 10.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) .................................................................. 36 10.3. MEASUREMENT EQUIPMENT USED .................................................................................................. 36 10.4. LIMITS AND MEASUREMENT RESULT................................................................................................ 36 11. RADIATED EMISSION ................................................................................................................................. 40 11.1. MEASUREMENT PROCEDURE ............................................................................................................ 40 11.2. TEST SETUP .......................................................................................................................................... 41 11.3. LIMITS AND MEASUREMENT RESULT.......................................................…

Text truncated - open the document above for the full version.

Report No.: AGC10232200801FE03 Page 51 of 76 EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 2 Antenna Horizontal FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 4880.00047.130.1447.2774-26.73 peak 4880.00036.550.1436.6954-17.31 AVG 7320.00041.762.3644.1274-29.88 peak 7320.00032.942.3635.354-18.7 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 2 Antenna Vertical FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 4880.00048.350.1448.4974-25.51 peak 4880.00037.540.1437.6854-16.32 AVG 7320.00042.192.3644.5574-29.45 peak 7320.00031.972.3634.3354-19.67 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type Report No.: AGC10232200801FE03 Page 52 of 76 EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Horizontal FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 4960.00049.150.2249.3774-24.63 peak 4960.00038.270.2238.4954-15.51 AVG 7440.00042.182.6444.8274-29.18 peak 7440.00031.492.6434.1354-19.87 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Vertical FrequencyMeter ReadingFactorEmission LevelLimitsMargin (MHz)(dBμV)(dB)(dBμV/m)(dBμV/m)(dB) 4960.00048.370.2248.5974-25.41 peak 4960.00037.450.2237.6754-16.33 AVG 7440.00041.282.6443.9274-30.08 peak 7440.00030.462.6433.154-20.9 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Value Type RESULT: PASS Note: The amplitude of other spurious emissions from 1G to 25 GHz which are attenuated more than 20 dB below the permissible value need not be reported. Factor = Antenna Factor + Cable loss - Amplifier gain, Over=Measure-Limit. The “Factor” value can be calculated automatically by software of measurement system. All the test modes of two antennas had been tested, the mode 1 was the worst case. Only the data of the worst case would be record in this test report. Report No.: AGC10232200801FE03 Page 53 of 76 TEST RESULT FOR RESTRICTED BANDS REQUIREMENTS ANTENNA 1 EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Horizontal PK AV RESULT: PASS Report No.: AGC10232200801FE03 Page 54 of 76 EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Vertical PK AV RESULT: PASS Report No.: AGC10232200801FE03 Page 55 of 76 EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Horizontal PK AV RESULT: PASS Report No.: AGC10232200801FE03 Page 56 of 76 EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Vertical PK AV RESULT: PASS Report No.: AGC10232200801FE03 Page 57 of 76 ANTENNA 2 EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Horizontal PK AV RESULT: PASS Report No.: AGC10232200801FE03 Page 58 of 76 EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 1 Antenna Vertical PK AV RESULT: PASS Report No.: AGC10232200801FE03 Page 59 of 76 EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Horizontal PK AV RESULT: PASS Report No.: AGC10232200801FE03 Page 60 of 76 EUT Wireless Microphone System - Transmitter Model Name Wireless GO II Transmitter Temperature 21.8°C Relative Humidity 58% Pressure 960hPa Test Voltage Normal Voltage Test Mode Mode 3 Antenna Vertical PK AV RESULT: PASS Note: The factor had been edited in the “Input Correction” of the Spectrum Analyzer. Report No.: AGC10232200801FE03 Page 61 of 76 12. LINE CONDUCTED EMISSION TEST 12.1. LIMITS OF LINE CONDUCTED EMISSION TEST Frequency Maximum RF Line Voltage Q.P.( dBuV) Average( dBuV) 150kHz~500kHz 66-56 56-46 500kHz~5MHz 56 46 5MHz~30MHz 60 50 Note: 1. The lower limit shall apply at the transition frequency. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50 MHz. 12.2. BLOCK DIAGRAM OF LINE CONDUCTED EMISSION TEST EUT & Support Units Report No.: AGC10232200801FE03 Page 62 of 76 12.3. PRELIMINARY PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. 2. Support equipment, if needed, was pl…

Text truncated - open the document above for the full version.

Test Setup Photos RADIATED EMISSION TEST SETUP BELOW 1GHZ RADIATED EMISSION TEST SETUP ABOVE 1GHZ CONDUCTED EMISSION TEST SETUP CONDUCTED TEST SETUP