2AEP6-EQ-2BPORTABLE BATTERY CAMERA

HangZhou XiongMai Technology CO., LTD 9th Floor, Building 9, Yinhu Innovation Center, No.9 FuXian Road, YinHu Street, Hangzhou, China Date: May 21, 2020 FCC ID: 2AEP6-EQ-2B Model Number: EQ-2B,XM-JPE13-2R,XM-JPED-2P,XM-JPEB2-F2,XM-JPEC2-R, XM-JPE2-2R,XM-JPEG-2D,XM-JPEG2-R,XM-JPEH-2R,ES-2R,XM-JPEG-2D, XM-JPEL-2D,XM-JPEG-3D,XM-JPEB4-F2,XM-JPEG-2D4G,XM-JPEG-3D4G, XM-JPEL-2D4G,EL-2D4G To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD To Whom It May Concern, We, HangZhou XiongMai Technology CO., LTD, declare that this EUT (FCC ID: 2AEP6-EQ-2B) doesn’t have Ad Hoc mode function on “non-US/Canada frequencies”. In addition. The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, (Signed) Name: Ping Yao Company: HangZhou XiongMai Technology CO., LTD Address: 9th Floor, Building 9, Yinhu Innovation Center, No.9 FuXian Road, YinHu Street, Hangzhou, China Phone: 0571-23271188 Fax: 0571-23271690 E-Mail: [email protected]

HangZhou XiongMai Technology CO., LTD Agent Authorization Date: May 21, 2020 Company: HangZhou XiongMai Technology CO., LTD Address: 9th Floor, Building 9, Yinhu Innovation Center, No.9 FuXian Road, YinHu Street, Hangzhou, China Product Description: PORTABLE BATTERY CAMERA FCC ID Number: 2AEP6-EQ-2B Tested Model Number: EQ-2B,XM-JPE13-2R,XM-JPED-2P,XM-JPEB2-F2,XM-JPEC2-R, XM-JPE2-2R,XM-JPEG-2D,XM-JPEG2-R,XM-JPEH-2R,ES-2R,XM-JPEG-2D, XM-JPEL-2D,XM-JPEG-3D,XM-JPEB4-F2,XM-JPEG-2D4G,XM-JPEG-3D4G, XM-JPEL-2D4G,EL-2D4G We authorize Eurofins Product Service GmbH, Storkower Strasse 38c, D-15526 Reichenwalde, Germany, to act on our behalf on all matters concerning the certification of above mentioned equipment. We declare that Eurofins Product Service GmbH is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We, HangZhou XiongMai Technology CO., LTD, the undersigned, hereby authorize Shenzhen Toby Technology Co., Ltd. (Ivan Su, Supervisor of EMC Dep.), Shenzhen Microwave Certification Services Co., Ltd. (Gilbert Lui, Marketing Manager) and Ka.Ma.S UG (Karin Schmidt, CEO) on our behalf, to apply to the Federal Communications Commission on our equipment. We, the undersigned, hereby authorize Shenzhen Toby Technology Co., Ltd. (Ivan Su, Supervisor of EMC Dep.) to act on our behalf in matters relating to the application for a FCC equipment authorization for mentioned FCC ID Number including the signing of Form 731, necessary forms and documents in connection with this application. Any and all acts carried out by Shenzhen Toby Technology Co., Ltd. (Ivan Su, Supervisor of EMC Dep.) on our behalf shall have the same effect as acts of our own. This authorization expires on 31th December, 2020. Yours Sincerely, HangZhou XiongMai Technology CO., LTD <Signature of Hirotaka Shiojima > ----------------------------------------------------------------------------------- Ping Yao 9th Floor, Building 9, Yinhu Innovation Center, No.9 FuXian Road, YinHu Street, Hangzhou, China Phone: 0571-23271188 Email: [email protected]

HangZhou XiongMai Technology CO., LTD Declaration Letter of Model Difference Date: May 21, 2020 FCC ID Number: 2AEP6-EQ-2B Tested Model Number: EQ-2B Adding Model Number(s): EQ-2B,XM-JPE13-2R,XM-JPED-2P,XM-JPEB2-F2,XM-JPEC2- R,XM-JPE2-2R,XM-JPEG-2D,XM-JPEG2-R,XM-JPEH-2R,ES-2R,XM-JPEG-2D,XM-JPEL- 2D,XM-JPEG-3D,XM-JPEB4-F2,XM-JPEG-2D4G,XM-JPEG-3D4G,XM-JPEL-2D4G,EL-2D4G All these models are in the same PCB, layout and electrical circuit, the only difference is the model name. Yours Sincerely, HangZhou XiongMai Technology CO., LTD <Signature of Hirotaka Shiojima > ----------------------------------------------------------------------------------- Ping Yao 9th Floor, Building 9, Yinhu Innovation Center, No.9 FuXian Road, YinHu Street, Hangzhou, China Phone: 0571-23271188 Email: [email protected]

HangZhou XiongMai Technology CO., LTD CONFIDENTIALITY REQUEST for Certification under the FCC Rules Date: May 21, 2020 Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 TO WHOM IT MAY CONCERN Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we request confidentiality for the following product: FCC ID Number: 2AEP6-EQ-2B Tested Model Number: EQ-2B For the product stated above, we request that the following information be held confidential: Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days Block Diagram Schematic Diagram/ Circuit Diagram Circuit Description/ Operational Description Parts List Tune Up Information User’s Manual External Photos Internal Photos Test Setup Photos The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. Please do not hesitate to contact me if you have any queries. Yours Sincerely, HangZhou XiongMai Technology CO., LTD <Signature of Hirotaka Shiojima > ----------------------------------------------------------------------------------- Ping Yao 9th Floor, Building 9, Yinhu Innovation Center, No.9 FuXian Road, YinHu Street, Hangzhou, China Phone: 0571-23271188 Email: [email protected]

Page : 2 of 11 TB-RF-075-1.0 Appendix III EUT External Photographs Model: EQ-2B Photo 1 External of EUT Page : 3 of 11 TB-RF-075-1.0 Page : 4 of 11 TB-RF-075-1.0

Page : 1 of 11 TB-RF-074-1.0 Appendix IFCC ID Label Model: EQ-2B Appendix II ID Label Location ID LOCATION FCC ID: 2AEP6-EQ-2B Model: EQ-2B This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Page : 5 of 11 TB-RF-075-1.0 Appendix IV EUT Internal Photographs Model: EQ-2B Photo 2 Internal of EUT Page : 6 of 11 TB-RF-075-1.0 Page : 7 of 11 TB-RF-075-1.0 Page : 8 of 11 TB-RF-075-1.0 Page : 9 of 11 TB-RF-075-1.0

Shenzhen Toby Technology Co., Ltd. Report No.: TB-MPE173169 Page: 1 of 3 TB-RF-074-1.0 1A/F., Bldg.6, Yusheng Industrial Zone, The National Road No.107 Xixiang Section 467, Xixiang, Bao’an, Shenzhen, China Tel: +86 75526509301 Fax: +86 75526509195 RF Exposure Evaluation FCC ID: 2AEP6-EQ-2B 1. Client Information Applicant : HangZhou XiongMai Technology CO., LTD Address : 9th Floor, Building 9, Yinhu Innovation Center, No.9 FuXian Road, YinHu Street, Hangzhou, China Manufacturer : HangZhou XiongMai Technology CO., LTD Address : 9th Floor, Building 9, Yinhu Innovation Center, No.9 FuXian Road, YinHu Street, Hangzhou, China 2. General Description of EUT EUT Name : PORTABLE BATTERY CAMERA Models No. : EQ-2B,XM-JPE13-2R,XM-JPED-2P,XM-JPEB2-F2,XM-JPEC2-R, XM-JPE2-2R,XM-JPEG-2D,XM-JPEG2-R,XM-JPEH-2R,ES-2R, XM-JPEG-2D,XM-JPEL-2D,XM-JPEG-3D,XM-JPEB4-F2,XM-JPEG- 2D4G,XM-JPEG-3D4G,XM-JPEL-2D4G,EL-2D4G Model Difference : All these models are in the same PCB, layout and electrical circuit, the only difference is the model name Product Description : Operation Frequency: 2.4G: 802.11b/g/n(HT20): 2412MHz~2462MHz 802.11n(HT40): 2422MHz~2452MHz Modulation Type: 802.11b: DSSS(CCK, DQPSK, DBPSK) 802.11g/n: OFDM(BPSK,QPSK,16QAM, 64QAM) Power Rating : Input: DC 5V Software Version : V1.0 Hardware Version : XMJP-BIRD-SD-IO V1.03 Connecting I/O Port(S) : Please refer to the User's Manual Remark : The antenna gain provided by the applicant, the verified for the RF conduction test provided by TOBY test lab. Note: More test information about the EUT please refer the RF Test Report. Report No.: TB-MPE173169 Page: 2 of 3 TB-RF-074-1.0 MPE Calculations for WIFI 1. Antenna Gain: . PIFA Ant: Model Frequency Range N/A 2400~2483.5MHz 3dBi 2. EUT Operation Condition: Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 3. Exposure Evaluation: Equation from page 18 of OET Bulletin 65, Edition 97-01 S=(PG)/4πR 2 Where S: power density P: power input to the antenna G: power gain of the antenna in the direction of interest relative to an isotropic radiator. R: distance to the center of radiation of the antenna 4. Test Result: 2.4G WIFI&BLE Mode Conducted Power(max) (dBm) Turn-up Power (dB) Max tune up power (dBm) [P] ANT Gain (dBi) [G] Distance (cm) [R] Power Density (mW/ cm 2 ) [S] Limit of Power Density (mW/ cm 2 ) (S) 802.11B 17.21 17±1 18 3.0 20 0.0250 1 802.11G 16.12 16±1 17 3.0 20 0.0199 1 802.11N(HT20) 15.96 16±1 17 3.0 20 0.0199 1 802.11N(HT40) 14.31 14±1 15 30 20 0.0126 1 Report No.: TB-MPE173169 Page: 3 of 3 TB-RF-074-1.0 5. Conclusion: As specified in Table 1B of 47 CFR 1.1310- Limits for Maximum Permissible Exposure (MPE), Limits for General Population/ Uncontrolled Exposure Frequency Range (MHz) Power density (mW/ cm 2 ) 300-1,500 F/1500 1,500-100,000 1.0 For BT&BLE:2402~2480 MHz For WIFI: 802.11b/g/n(HT20): 2412MHz~2462MHz 802.11n(HT40): 2422MHz~2452MHz MPE limit S: 1mW/ cm 2 The MPE is calculated as 0.0250mW / cm2 < limit 1mW / cm 2 . So, RF exposure limit warning or SAR test are not required. The EUT will only be used with a separation of 20cm or greater between the antenna and nearby persons and can therefore be considered a mobile transmitter per 47 CFR2.1091 (b). The RF Exposure Information page from the manual is included here for reference. Note For a more detailed features description, please refer to the RF Test Report. -----END OF REPORT-----

Shenzhen Toby Technology Co., Ltd. Report No.: TB-FCC173168 Page: 1 of 82 TB-RF-074-1.0 1A/F., Bldg.6, Yusheng Industrial Zone, The National Road No.107 Xixiang Section 467, Xixiang, Bao’an, Shenzhen, China Tel: +86 75526509301 Fax: +86 75526509195 FCC Radio Test Report FCC ID: 2AEP6-EQ-2B Original Grant Report No. : TB-FCC173168 Applicant : HangZhou XiongMai Technology CO., LTD Equipment Under Test (EUT) EUT Name : PORTABLE BATTERY CAMERA Model No. : EQ-2B Series Model No. : XM-JPE13-2R,XM-JPED-2P,XM-JPEB2-F2,XM-JPEC2-R, XM-JPE2-2R,XM-JPEG-2D,XM-JPEG2-R,XM-JPEH-2R, ES-2R,XM-JPEG-2D,XM-JPEL-2D,XM-JPEG-3D, XM-JPEB4-F2,XM-JPEG-2D4G,XM-JPEG-3D4G, XM-JPEL-2D4G,EL-2D4G Brand Name : N/A Receipt Date : 2020-05-13 Test Date : 2020-05-13 to 2020-05-18 Issue Date : 2020-05-19 Standards : FCC Part 15, Subpart C (15.247 :2019) Test Method : ANSI C63.10: 2013 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above, The EUT technically complies with the FCC and IC requirements Test/Witness Engineer : Garen Engineer Supervisor : Ivan Su Engineer Manager : Ray Lai This report details the results of the testing carried out on one sample. The results contained in Report No.: TB-FCC173168 Page: 2 of 82 TB-RF-074-1.0 this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Contents CONTENTS ............................................................................................................................................. 2 1. GENERAL INFORMATION ABOUT EUT ............................................................................. 5 1.1 Client Information ................................................................................................................. 5 1.2 General Description of EUT (Equipment Under Test) ................................................... 5 1.3 Block Diagram Showing the Configuration of System Tested ...................................... 6 1.4 Description of Support Units .............................................................................................. 6 1.5 Description of Test Mode .................................................................................................... 6 1.6 Description of Test Software Setting ................................................................................ 8 1.7 Measurement Uncertainty .................................................................................................. 8 1.8 Test Facility ........................................................................................................................... 9 2. TEST SUMMARY ..................................................................................................................... 10 3. TEST EQUIPMENT .................................................................................................................. 11 4. CONDUCTED EMISSION TEST ........................................................................................... 11 4.1 Test Standard and Limit .................................................................................................... 12 4.2 Test Setup ........................................................................................................................... 12 4.3 Test Procedure ................................................................................................................... 12 4.4 EUT Operating Mode ........................................................................................................ 13 4.5 Test Data ............................................................................................................................. 13 5. RADIATED EMISSION TEST ................................................................................................ 14 5.1 Test Standard and Limit .................................................................................................... 14 5.2 Test Setup ........................................................................................................................... 15 5.3 Test Procedure ................................................................................................................... 16 5.4 EUT Operating Condition ................................................................................................. 16 5.5 Test Data ............................................................................................................................. 17 6. RESTRICTED BANDS REQUIREMENT ............................................................................. 18 6.1 Test Standard and Limit .................................................................................................... 18 6.2 Test Setup ........................................................................................................................... 18 6.3 Test Procedure ................................................................................................................... 18 6.4 EUT Operating Condition ................................................................................................. 19 6.5 Test Data ............................................................................................................................. 19 7. BANDWIDTH TEST ................................................................................................................. 20 7.1 Test Standard and Limit .................................................................................................... 20 7.2 Test Setup ........................................................................................................................... 20 7.3 Test Procedure ................................................................................................................... 20 7.4 EUT Operatin…

Text truncated - open the document above for the full version.

Page : 10 of 11 TB-RF-075-1.0 Appendix V EUT Test Photographs 15C Test Setup Model: EQ-2B Photo of Setup for Radiated Emission (Below 1 GHz) Photo of Setup for Radiated Emission (Above 1 GHz) Page : 11 of 11 TB-RF-075-1.0 Photo of Setup for Conducted Emission -----END OF REPORT-----