2AEP6-XM-JPRZ-2RRobot Camera

FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. .

Hangzhou Xiongmai Technology Co., Ltd. Add: 9th Floor,Building 9, Yinhu Innovation Center, No.9 Fuxian Road, Yinhu Street, Hangzhou, China. Date: 2021-5-21 FCC ID: 2AEP6-XM-JPRZ-2R Dear Sir/Madam, We, Hangzhou Xiongmai Technology Co., Ltd. Hereby declares the following statement for Federal Communications Commission, PCB board, circuit, structure and internal of these model(s) are the same, Only model number is different for these model: Product name: Robot Camera Model no.: XM-JPRZ-2R , XM-JPRZ-3R, XM-JPRZ-3D, XM-JPRZ-4R, XM-JPRZ-5R, XM-JPRZ-2D, XM-JPRZ-4D, XM-JPRZ-5D Sincerely, Name/Title ： Ping Yao/ manager Company: Hangzhou Xiongmai Technology Co., Ltd. Address: 9th Floor,Building 9, Yinhu Innovation Center, No.9 Fuxian Road, Yinhu Street, Hangzhou, China. Phone: 0571 - 23271188 Fax: 0571 - 23271690 E - Mail: [email protected]

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date:<2021-5-21> Pursuant to Paragraphs §0.457 and 0.459 of the Commission’s Rules (47 C.F.R.) and Section §552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products: FCC ID Model name 2AEP6-XM-JPRZ-2R XM-JPRZ-2R For the product stated above, we request that the following information be held confidential; Exhibits Long-Term Confidentiality Short-Term Confidentiality Short-Term Confidentiality Days External Photos Internal Photos Block Diagram Schematics Test Setup Photos User’s Manual Parts List Tune Up Operational Descriptions The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Name/Title ： Ping Yao / manager Company: Hangzhou Xiongmai Technology Co., Ltd. Address: 9th Floor,Building 9, Yinhu Innovation Center, No.9 Fuxian Road, Yinhu Street, Hangzhou, China. Phone: 0571 - 23271188 Fax: 0571 - 23271690 E - Mail: [email protected]

Hangzhou Xiongmai Technology Co., Ltd. 9th Floor,Building 9, Yinhu Innovation Center, No.9 Fuxian Road, Yinhu Street, Hangzhou, China. Date: 2021-5-21 FCC ID: 2AEP6-XM-JPRZ-2R Model Number: XM-JPRZ-2R To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD To Whom It May Concern, We, Hangzhou Xiongmai Technology Co., Ltd., declare that this EUT (FCC ID: 2AEP6-XM-JPRZ-2R) doesn’t have Ad Hoc mode function on “non-US/Canada frequencies”. In addition. The frequency selection feature is disabled by firmware for devices marked to the US/Canada. For DTS part of this device, only channels 1-11 will be used in North America, Country code selection is disabled. Should you have any questions or comments regarding this matter, please have my best attention. Sincerely, Name/Title ： Ping Yao / manager Company: Hangzhou Xiongmai Technology Co., Ltd. Address: 9th Floor,Building 9, Yinhu Innovation Center, No.9 Fuxian Road, Yinhu Street, Hangzhou, China. Phone: 0571 - 23271188 Fax: 0571 - 23271690 E - Mail: [email protected]

Hangzhou Xiongmai Technology Co., Ltd. 9th Floor,Building 9, Yinhu Innovation Center, No.9 Fuxian Road, Yinhu Street, Hangzhou, China. Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2021-5-21 To whom it may concern: We, Hangzhou Xiongmai Technology Co., Ltd. the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AEP6-XM-JPRZ-2R including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, Name/Title ： Ping Yao / manager Company: Hangzhou Xiongmai Technology Co., Ltd. Address: 9th Floor,Building 9, Yinhu Innovation Center, No.9 Fuxian Road, Yinhu Street, Hangzhou, China. Phone: 0571 - 23271188 Fax: 0571 - 23271690 E - Mail: [email protected]

FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Appendix III EUT External Photographs Photo 1 Appearance of EUT Photo 2 Appearance of Adapter FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Photo 3 Appearance of Adapter Photo 4 Appearance of EUT FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Photo 5 Appearance of EUT Photo 6 Appearance of EUT FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Photo 7 Appearance of EUT Photo 8 Appearance of EUT

FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Appendix IFCC ID Label Size for the label: 20mm X20mm FCC ID: 2AEP6-XM-JPRZ-2R Model: XM-JPRZ-2R FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Appendix II ID Label Location ID LOCATION

FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Appendix IV EUT Internal Photographs Photo 9 Internal of EUT Photo 10 In ternal of EUT 9 FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Photo 11 Internal of PCB Photo 12 Appearance of PCB FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Photo 13 Appearance of PCB Photo 14 Appearance of PCB FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Photo 15 Appearance of PCB Photo 16 Internal of EUT FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Photo 17 Appearance of PCB Photo 18 Appearance of PCB 2.4G WIFI Antenna FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Photo 19 Appearance of PCB Photo 20 Appearance of PCB

Report No.: TB-MPE179276 Page: 1 of 3 TB-RF-075-1.0 Maximum Permissible Exposure Evaluation FCC ID: 2AEP6-XM-JPRZ-2R 1. Client Information Applicant : Hangzhou Xiongmai Technology Co., Ltd. Address : 9th Floor,Building 9, Yinhu Innovation Center, No.9 Fuxian Road, Yinhu Street, Hangzhou, China. Manufacturer : Hangzhou Xiongmai Technology Co., Ltd. Address : 9th Floor,Building 9, Yinhu Innovation Center, No.9 Fuxian Road, Yinhu Street, Hangzhou, China. 2. General Description of EUT EUT Name : Robot Camera Models No. : XM-JPRZ-2R, XM-JPRZ-3R, XM-JPRZ-3D, XM-JPRZ-4R, XM-JPRZ-5R, XM-JPRZ-2D, XM-JPRZ-4D, XM-JPRZ-5D Model Different : All these models are identical in the same PCB, layout and electrical circuit, the only difference is model name. Brand Name : N/A Product Description : Operation Frequency: 802.11b/g/n(HT20): 2412MHz~2462MHz 802.11n (HT40):2422MHz~2452MHz Number of Channel: 802.11b/g/n(HT20):11 Channels 802.11n (HT40):7 Channels RF Output Power: 802.11b: 18.304 dBm 802.11g: 19.154 dBm 802.11n(HT20): 19.160 dBm 802.11n(HT40): 17.847 dBm Antenna Gain: 3.0dBi Internal Antenna Power Rating : DC 5V from adapter: Input: AC 100-240V 50/60Hz Output: DC 5V1.2A Software Version : V1.0 Hardware Version : V1.0 Connecting I/O Port(S) : Please refer to the User's Manual Remark : the MPE report used the EUT (20210309-22-2#). Report No.: TB-MPE179276 Page: 2 of 3 TB-RF-075-1.0 MPE Calculations for WIFI 1. Antenna Gain: Internal Antenna:3.0dBi. 2. EUT Operation Condition: Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. 3. Exposure Evaluation: Equation from page 18 of OET Bulletin 65, Edition 97-01 S=(PG)/4πR 2 Where S: power density P: power input to the antenna G: power gain of the antenna in the direction of interest relative to an isotropic radiator. R: distance to the center of radiation of the antenna 4. Test Result: 2.4G WiFi Mode Conducted Power(max) (dBm) Turn-up Power (dB) Max tune up power (dBm) [P] ANT Gain (dBi) [G] Distance (cm) [R] Power Density (mW/ cm 2 ) [S] Limit of Power Density (mW/ cm 2 ) (S) 802.11B 18.304 18 ±1 19 3 20 0.03150 1 802.11G 19.154 19 ±1 20 3 20 0.03970 1 802.11N(HT20) 19.160 19 ±1 20 3 20 0.03970 1 802.11N(HT40) 17.847 17 ±1 18 3 20 0.02500 1 Report No.: TB-MPE179276 Page: 3 of 3 TB-RF-075-1.0 5. Conclusion: As specified in Table 1B of 47 CFR 1.1310- Limits for Maximum Permissible Exposure (MPE), Limits for General Population/ Uncontrolled Exposure Frequency Range (MHz) Power density (mW/ cm 2 ) 300-1,500 F/1500 1,500-100,000 1.0 For 2.4WIFI:2412~2462 MHz MPE limit S: 1mW/ cm 2 The MPE is calculated as 0.03970 mW / cm 2 < limit 1mW / cm 2 . So, RF exposure limit warning or SAR test are not required. The EUT will only be used with a separation of 20cm or greater between the antenna and nearby persons and can therefore be considered a mobile transmitter per 47 CFR2.1091 (b). The RF Exposure Information page from the manual is included here for reference. Note For a more detailed features description, please refer to the RF Test Report. 6. Conclusion: The measurement results comply with the FCC Limit per 47 CFR 2.1091 for the uncontrolled RF Exposure of mobile device. -----END OF REPORT-----

Shenzhen Toby Technology Co., Ltd. Report No.: TB-FCC179275 Page: 1 of 78 TB-RF-074-1.0 1/F.,Building 6, Rundongsheng Industrial Zone, Longzhu, Xixiang, Bao'an District, Shenzhen, Guangdong, China Tel: +86 75526509301 Fax: +86 75526509195 FCC Radio Test Report FCC ID: 2AEP6-XM-JPRZ-2R Original Grant Report No. : TB-FCC179275 Applicant : Hangzhou Xiongmai Technology Co., Ltd. Equipment Under Test (EUT) EUT Name : Robot Camera Model No. : XM-JPRZ-2R Series Model No. : XM-JPRZ-3R, XM-JPRZ-3D, XM-JPRZ-4R, XM-JPRZ-5R, XM-JPRZ-2D, XM-JPRZ-4D, XM-JPRZ-5D S/N : N/A Brand Name : N/A Sample ID : 20210309-22-1#& 20210309-22-2# Receipt Date : 2021-03-24 Test Date : 2021-03-25 to 2021-05-19 Issue Date : 2021-05-21 Standards : FCC Part 15, Subpart C 15.247 Test Method : ANSI C63.10: 2013 Conclusions : PASS In the configuration tested, the EUT complied with the standards specified above, The EUT technically complies with the FCC and IC requirements Test/Witness Engineer : Wade. Lv Engineer Supervisor : Ivan Su Engineer Manager : Ray Lai This report details the results of the testing carried out on one sample. The results contained in this test report do not relate to other samples of the same product. The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in the report. Report No.: TB-FCC179275 Page: 2 of 78 TB-RF-074-1.0 Contents CONTENTS ............................................................................................................................................. 2 1. GENERAL INFORMATION ABOUT EUT.............................................................................. 5 1.1 Client Information ................................................................................................................. 5 1.2 General Description of EUT (Equipment Under Test) ................................................... 5 1.3 Block Diagram Showing the Configuration of System Tested ...................................... 6 1.4 Description of Support Units .............................................................................................. 6 1.5 Description of Test Mode .................................................................................................... 7 1.6 Description of Test Software Setting ................................................................................ 8 1.7 Measurement Uncertainty .................................................................................................. 8 1.8 Test Facility ........................................................................................................................... 9 2. TEST SUMMARY ..................................................................................................................... 10 3. TEST SOFTWARE ................................................................................................................... 10 4. TEST EQUIPMENT .................................................................................................................. 11 5. CONDUCTED EMISSION TEST ........................................................................................... 12 5.1 Test Standard and Limit .................................................................................................... 12 5.2 Test Setup ........................................................................................................................... 12 5.3 Test Procedure ................................................................................................................... 13 5.4 Deviation From Test Standard ......................................................................................... 13 5.5 EUT Operating Mode ........................................................................................................ 13 5.6 Test Data ............................................................................................................................. 13 6. RADIATED EMISSION TEST ................................................................................................ 14 6.1 Test Standard and Limit .................................................................................................... 14 6.2 Test Setup ........................................................................................................................... 15 6.3 Test Procedure ................................................................................................................... 16 6.4 Deviation From Test Standard ......................................................................................... 17 6.5 EUT Operating Condition ................................................................................................. 17 6.6 Test Data ............................................................................................................................. 17 7. RESTRICTED BANDS REQUIREMENT ............................................................................. 18 7.1 Test Standard and Limit .................................................................................................... 18 7.2 Test Setup ........................................................................................................................... 18 7.3 Test Procedure ................................................................................................................... 19 7.4 Deviation From Test Standard ......................................................................................... 19 7.5 EUT Operating Condition ................................................................................................. 19 7.6 Test Data ............................................................................................................................. 19 8. BANDWIDTH TEST ......................................................................................................…

Text truncated - open the document above for the full version.

FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Appendix V EUT Test Photographs 15C Test Setup Photo of Setup for Radiated Emission (Above 1 GHz) Photo of Setup for Radiated Emission (Below 1 GHz) FCC ID:2AEP6-XM-JPRZ-2R TB-RF-074-1.0 Photo of Setup for Conducted Emission -----END OF REPORT-----