2AFP2LC05Sterilizer with Wireless Charging

无线充电消毒盒 使用方法充电示意图连接适配器 本产品通过磁感应方式实现短距离无线电能传输，产品是 快速无线充电发射器.本产品外观精致，有较宽的工作电压（DC 5 V-12V）能适应绝大多数USB TYPE-C输出的普通适配器或符合 PD标准的适配器（使用QC USB TYPE-C,PD适配器时本产品默认 在9V）。本产品还具有给手机进行紫外线消毒的功能。 将电源适配器插在插座上。 注： 本产品同时兼容Type-C 至 Type-C电源线。QC2.0或者QC3.0及PD标 准的电源适配器才能支持本产品快充功能。USB-A至 USB-C电源线和适配器另 外购买。 Type-C 电源线一端连接适配器，一端连接无线充电消毒盒充上。 上电：蓝绿灯交替闪烁2S，绿灯长亮进入待机。 5V/3A, 9V/2.22A,12V/1.67A 225 x 50 x 127mm 390g 将发射器通过USB TYPE-C线连接（QC USB TYPE-C,PD适配器）， 产品工作如果使用PD适配器和符合QC标准的适配器，产品可以为 iphone12实现7.5W 快速无线充电模式。 将手机放入盒内，合盖后轻触触摸开关，产品进行紫外线消毒工 作。产品指示灯亮红色。 待机：绿灯长亮。 充电：蓝灯长亮。 3 充满：充满后转绿灯。 4 FOD及异常：蓝色灯闪烁 紫外线消毒：红灯长亮直至30分钟消毒完成。亮灯方式恢复至当 前工作状态。 1.请勿挤压或者碰撞。 2.请勿自行拆卸或者投入火中、水中。避免造成短路漏电。 3.请勿在严重高温、潮湿或腐蚀性环境下使用无线充电消毒盒，避免损 坏电路出现漏电现象。 4.请勿与带磁条或者芯片的磁卡（身份证。银行卡等）放置太久，避免造 成磁卡失效。 5.请保持植入医疗设备（心脏起搏器、植入耳蜗等）与无线充电消毒盒之 间保持距离至少为20cm，以避免对医疗设备造成潜在干扰。 6.请看管好儿童，以确保他们不将无线充电消毒盒来玩，以避免不必要 的意外。 5 6 用户手册 用户手册 适配器 Type-C 接口 Type-C 电源线 65*85mm 无线充电器说明书 1:1 LC05 中性 105g铜版纸，双面四色 印刷 / 2021.06.21 1.0 Sterilizer with Wireless Charging Method of Application Charging DiagramNotesConnect to Adapter This product realizes short-distance wireless power transmission by magnetic induction, and it is a fast wireless charging transmitter. This product has exquisite appearance and wide working voltage (DC 5V-12V), which can adapt to most USB TYPE-C output QC standard adapters or PD standard adapters (when using QC USB TYPE-C, PD adapter, this product defaults At 9V). This product also has the function of UV disinfection for phones. Connect the power adapter to socket. Note: This product is also compatible with Type-C to Type-C cables. Only QC2.0 or QC3.0 standard power adapter support this product’s quick charge function. Type-C to Type-C and power adapter need to buy separately. Type-C cable one interface connected to the power adapter , the other interface to UV Sterilizer Box Wireless Charger. 1.Power on: Blue and green lights flash alternately for 2S, and the green lights stay on for standby. Connect the transmitter through the USB TYPE-C cable (QC USB TYPE-C, PD adapter). If the product works with a PD adapter and QC standard adapter, the product can achieve a 7.5W fast wireless charging mode for iphone12. Put the mobile phone in the box, touch the touch switch after closing the cover, and the product will be disinfected by UV. The product indicator lights up red. 2.Standby: the indicator light is always green. 3.Charging: the indicator light will stay blue. 3 4.Charging Full: the indicator light turn green. 4 5.FOD and abnormal: blue light flashes 6.UV disinfection: The red light stays on until the disinfection is completed in 30 minutes. After that, the lighting mode is restored to the current working state. 1.Do not squeeze or collisions. 2.Do not disassemble or throw into fire or water,to avoid causing a short circuit leakage. 3.Do not use wireless charging UV sterilization box in severely hot,humid or corrosive environments,to avoid circuit damage and occurs leakage phenomnon. 4.Do not place too close with magnetic stripe or chip card (ID card,bank cards,etc.)to avoid magnetic failure. 5.Please keep the distance at least 20cm between implantable medical devices(pacemakers,implantable cochlear,etc.)and the wireless charging UV sterilization box,to avoid potential interference with the medical device. 6.Please take care of the children to ensure that they don't play with the wireless charging UV sterilization box to avoid unnecessary accidents. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. 5 6 User Manual User Manual Power Adapter Type-C Cable Type-C Port FCC WARNING FCC ID：2AFP2LC05 2

C5266091_X8_Ed.1 1/1 Letter of Authorization Shenzhen Powerqi Technology Co., Ltd. Company: Shenzhen Powerqi Technology Co., Ltd. Address: Room 201, 302, 401 of A4 Building, Block A, Fangxing Science and Technology Park, No. 13 of Baonan Road, Longgang District, Shenzhen, China Product Name: Sterilizer with Wireless Charging Model Number: LC05 FCC Identifier: 2AFP2LC05 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Tina Qu Date: 7/8/2021 Title: Sales Manager Signature of applicant:

C5266091_X10_Ed.1 1/1 Shenzhen Powerqi Technology Co., Ltd. Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 7/8/2021 Subject: Request for Confidentiality FCC ID: 2AFP2LC05 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality ID Label/Location No No Attestation Statement No No External Photos No Block Diagram Schematics Test Report No No Test Setup Photos No User’s Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) No No SDR Software / Security Info No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Tina Qu Date: 7/8/2021 Title: Sales Manager

1 - Page 1 of 4 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] APPENDIX 1- EUT PHOTO Photo 1 (For model LC05) Photo 2 1 - Page 2 of 4 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 3 Photo 4 1 - Page 3 of 4 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 5 Photo 6 1 - Page 4 of 4 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 7 Photo 8

底壳 / 2021.7.07 100 100 1:1 LC05 中性 1.0    

1 - Page 1 of 7 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] APPENDIX 1- EUT PHOTO Photo 1 (For model LC05) Photo 2 1 - Page 2 of 7 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 3 Photo 4 1 - Page 3 of 7 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 5 Photo 6 1 - Page 4 of 7 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 7 Photo 8 1 - Page 5 of 7 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 9 Photo 10 1 - Page 6 of 7 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 11 Photo 12 1 - Page 7 of 7 - Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Photo 13 Coil antenna

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] RF EXPOSURE Test Report Report No.: MTi210311024-03E2 Date of issue: July 08, 2021 Applicant: Shenzhen Powerqi Technology Co., Ltd. Product name: Sterilizer with Wireless Charging Model(s): LC05 FCC ID: 2AFP2LC05 Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 11 - Report No.: MTi210311024-03E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Instructions 1. The report shall not be partially reproduced without the written consent of the laboratory; 2. The test results of this report are only responsible for the samples submitted; 3. This report is invalid without the seal and signature of the laboratory; 4. This report is invalid if transferred, altered or tampered with in any form without authorization; 5. Any objection to this report shall be submitted to the laboratory within 15 days from the date of receipt of the report. - Page 3 of 11 - Report No.: MTi210311024-03E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] TEST RESULT CERTIFICATION Applicant’s name .................... : Shenzhen Powerqi Technology Co., Ltd. Address .................................. : Room 201, 302, 401 of A4 Building, Block A, Fangxing Science and Technology Park, No. 13 of Baonan Road, Longgang District, Shenzhen, China Manufacturer's Name ............. : Shenzhen Powerqi Technology Co., Ltd. Address .................................. : Room 201, 302, 401 of A4 Building, Block A, Fangxing Science and Technology Park, No. 13 of Baonan Road, Longgang District, Shenzhen, China Product description Product name ........................... : Sterilizer with Wireless Charging Trademark ............................. : N/A Model Name .......................... : LC05 Serial Model ............................ N/A Standards ............................... : FCC CFR 47 PART 1 , 1.1310 Test procedure ....................... : KDB 680106 D01 RF Exposure Wireless Charging Apps v03r01 Date of Test Date (s) of performance of tests ............ : Mar. 16, 2021 ~ Mar. 25, 2021 Test Result ............................................. : Pass This device described above has been tested by Shenzhen Microtest Co., Ltd. and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Testing Engineer : (Danny Xu) Technical Manager : (Leo Su) Authorized Signatory : (Tom Xue) - Page 4 of 11 - Report No.: MTi210311024-03E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Table of Contents 1 GENERAL INFORMATION .......................................................................................................................................... 5 1.1 DESCRIPTION OF EUT ................................................................................................................................................... 5 1.2 ANCILLARY EQUIPMENT LIST ........................................................................................................................................... 5 1.3 MEASUREMENT UNCERTAINTY ........................................................................................................................................ 5 2 TESTING SITE ............................................................................................................................................................ 6 3 LIST OF TEST EQUIPMENT ......................................................................................................................................... 7 4 TEST RESULTS ........................................................................................................................................................... 8 4.4 MAXIMUM PERMISSIBLE EXPOSURE.................................................................................................................................. 8 4.4.1 Limit .................................................................................................................................................................... 8 4.4.2 Test Procedures ................................................................................................................................................... 8 4.4.3 Test Setup............................................................................................................................................................ 9 4.4.4 Test Result ........................................................................................................................................................... 9 4.4.5 MPE Setup photo .............................................................................................................................................. 11 - Page 5 of 11 - Report No.: MTi210311024-03E2 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] 1 General Information 1.1 Description of EUT Product name: Sterilizer with Wireless Charging Brand name: N/A Model name: LC05 Series model: N/A Deference in serial model: N/A Operation frequency: 115–2…

Text truncated - open the document above for the full version.

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Test Report Report No.: MTi210311024-03E1 Date of issue: July 08, 2021 Applicant: Shenzhen Powerqi Technology Co., Ltd. Product name: Sterilizer with Wireless Charging Model(s): LC05 FCC ID: 2AFP2LC05 Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 24 - Report No.: MTi210311024-03E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Instructions 1. The report shall not be partially reproduced without the written consent of the laboratory; 2. The test results of this report are only responsible for the samples submitted; 3. This report is invalid without the seal and signature of the laboratory; 4. This report is invalid if transferred, altered or tampered with in any form without authorization; 5. Any objection to this report shall be submitted to the laboratory within 15 days from the date of receipt of the report. - Page 3 of 24 - Report No.: MTi210311024-03E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’ an District, Shenzhen, Guangdong, China. Te l : (86-755)88850135 Fax: (86-755) 88850136 Web:www.mtitest.com E-mail: [email protected] Table of Contents 1 GENERAL INFORMATION ................................................................................................................................... 5 1.1 FEATURE OF EQUIPMENT UNDER TEST (EUT) ................................................................................................................... 5 1.2 TEST MODE .............................................................................................................................................................. 5 1.3 EUT TEST SETUP........................................................................................................................................................ 5 1.4 ANCILLARY EQUIPMENT .............................................................................................................................................. 5 2 SUMMARY OF TEST RESULT ............................................................................................................................... 6 2.1 OPERATION CHANNEL LIST ........................................................................................................................................... 6 2.2 TEST CHANNEL .......................................................................................................................................................... 6 3 TEST FACILITIES AND ACCREDITATIONS .............................................................................................................. 7 3.1 TEST LABORATORY ..................................................................................................................................................... 7 3.2 ENVIRONMENTAL CONDITIONS ..................................................................................................................................... 7 3.3 MEASUREMENT UNCERTAINTY ...................................................................................................................................... 7 4 LIST OF TEST EQUIPMENT .................................................................................................................................. 8 5 TEST RESULTS ..................................................................................................................................................... 9 5.1 ANTENNA REQUIREMENT ............................................................................................................................................ 9 5.1.1 Standard requirement ................................................................................................................................. 9 5.1.2 EUT Antenna ............................................................................................................................................... 9 5.2 CONDUCTED EMISSION ............................................................................................................................................. 10 5.2.1 Limits ......................................................................................................................................................... 10 5.2.2 Test Procedures ......................................................................................................................................... 10 5.2.3 Test Setup .................................................................................................................................................. 10 5.2.4 Test Result ................................................................................................................................................. 10 5.3 RADIATED EMISSION ................................................................................................................................................. 15 5.3.1 Limits ......................................................................................................................................................... 15 5.3.2 Test Procedures ......................................................................................................................................... 16 5.3.3 Test Setup .................................................................................................................................................. 17 5.3.4 Test Result ......................................................................................................................…

Text truncated - open the document above for the full version.

Model: LC05 Radiated emission Conducted emission