2AGGZ003B9ACA41AUTOMATE / Push15 Channel Remote

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device contains licence-exempt transmitter(s)/receiv- er(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: WARNING: Important safety instructions to be read before installation and use. Incorrect installation or use can lead to serious injury and will void manufacturer's liability and warranty. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. • Do not expose to water, moisture, humid and damp environments or extreme temperatures. • Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, should not be allowed to use this product. • Use or modication outside the scope of this instruction manual will void warranty. • Installation and programming to be performed by a suitably qualied installer. • Follow installation instructions. • For use with motorized shading devices. • Frequently inspect for improper operation. Do not use if repair or adjustment is necessary. • Keep clear when in operation. • Replace battery with correctly specied type. • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Operation Temperature Range: -10°C to +50°C Ratings: 3VDC, 15mA This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. WARNING: Do not ingest battery, Chemical Burn Hazard. 7 | Automate Programming Instructions | AC Tubular Motor s ROLLEASE ACMEDA Hold P1 Activat e Pairing Mode Sl eep Mode Reverse Direction Reset To Factory Settings Motor Response Motor Response Motor Response Motor Response Approx. Approx. Approx. Approx. NOTE Reverse motor direction from P1 button only when motor does not have any limits. 7 | Automate™ Programming Instructions | ARC™ Venetian Tilt Motor ROLLEASE ACMEDA Hold P1 Activat e Pairing Mode Motor Response Approx. Approx. P1 Press ConditionFunction Achieved Visual Feedback Audible Feedback Function Described Short Press then Rel ease (<2 sec) If limit is NOT setNoneNo ActionNoneNo Action If limits are set Operational control of motor , run to limit. Stop if running Motor runsNone Operational control of motor after pairing and limit setting is complet ed first time If motor is in “Sleep Mode” & limits are set (R ef er to Sec.10) Wake and control Motor wakes and runs in a direction None Motor is restor ed from Sl eep mode and RF control is active 3.2 Motor Configuration Options The P1 Button is utilized to administer motor configuration as described below and beginning in Section 4. Sl eep Mode Approx. Motor Response Reverse Direction Motor Response Motor Response RELEASE P1 RELEASE P1 RELEASE P1 Settings Approx. Reset To Factory Internal Tubular Large Tubular 0.8 Cord Lift Curtain Tilt Motor P1 P1 0.6 Cord Lift P1 13 | Automate ™ Programming Instructions | Ver sa Drapery Motor ROLLEASE ACMEDA 7 INITIAL SET UP 7.1 Pair motor with controller Consult user manual for your controller for information on selecting channel. Hold P1 button on motor head. Select channel on controller . Hold STOP on controller . Approx. Motor ResponseMotor Response Motor is now in setup mode and ready for setting limits IMPORTANT Notes: • When limits are not set only one remote channel can be paired with the motor • When limits are set, up to ten channels can be paired with the motor . Rever sing motor direction using this method is only possible during initial set-up To check trav el direction of shade, press UP or DOWN on controlle…

Text truncated - open the document above for the full version.

Date: 02‐14‐2023 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Ref: Attestation Statements Part 2.911(d)(5)(i) and Part 2.911(d)(5)(ii) Filing Re. KDB 986446 D01 FCC ID: 2AGGZ003B9ACA41 Dear Sir or Madam, Rollease Acmeda Inc. (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. We also certify that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. If you have any questions, please contact us. Sincerely, Contact name: Jonny Matuichuk Company name: Rollease Acmeda Inc Address: 750 East Main Street, 7th Floor, Stamford CT 06902, USA E-mail: [email protected] Tel: +1 203 832 6756 Signature:

Rev 1/26/2023 To: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 02‐14‐2023 Ref: Attestation Statements Part 2.911(d)(7) Filing FCC ID: 2AGGZ003B9ACA41 Rollease Acmeda inc. (“the applicant”) certifies that, as of the date of the filing of the application, Rollease Acmeda Inc. is our designated U.S. agent for service of pr ocess for the above referenced FCC ID. Rollease Acmeda Pty Inc. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission‐related proceeding involving the equipment. Rollease Acmeda In c. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above‐referenced FCC ID. Designated U.S. Agent Information: Contact name: Jonny Matuichuk Company name: Rollease Acmeda Inc Address: 750 East Main Street, 7th Floor, Stamford CT 06902, USA E-mail: [email protected] Tel: +1 203 832 6756 Sincerely, [Insert U.S. agent company name] SAME AS APPLICANT Jonny Matuichuk (U.S. agent company name signature) [Insert applicant name] Rollease Acmeda inc. (Applicant printed name) Jonny Matuichuk (Applicant signature)

1

1 of 1 To whom it may concern, Letter of Declaration We, Rollease Acmeda Inc, hereby declare the models below: Model(S): MT02‐0101‐050008‐A, MT02‐0101‐067008‐A FCC ID: 2AGGZ003B9ACA41 IC: 21769‐003B9ACA41 are identical in electrical and mechanical construction except for the colour code as shown in the below table: Product Code Colour code MT02‐0101‐067008‐A & MT02‐0101‐050008‐A Yours sincerely, Signature: Print name: Jonny Matuichuk Title: Product Manager Date: 16/11/2022

External Photos Documentation Manufacturer: Rollease Acmeda Inc Page 1 of 11 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 MT02-0101-067008-A External Photos Documentation Manufacturer: Rollease Acmeda Inc Page 2 of 11 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 External Photos Documentation Manufacturer: Rollease Acmeda Inc Page 3 of 11 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 External Photos Documentation Manufacturer: Rollease Acmeda Inc Page 4 of 11 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 External Photos Documentation Manufacturer: Rollease Acmeda Inc Page 5 of 11 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 External Photos Documentation Manufacturer: Rollease Acmeda Inc Page 6 of 11 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 External Photos Documentation Manufacturer: Rollease Acmeda Inc Page 7 of 11 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 MT02-0101-050008-A External Photos Documentation Manufacturer: Rollease Acmeda Inc Page 8 of 11 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 External Photos Documentation Manufacturer: Rollease Acmeda Inc Page 9 of 11 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 External Photos Documentation Manufacturer: Rollease Acmeda Inc Page 10 of 11 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 External Photos Documentation Manufacturer: Rollease Acmeda Inc Page 11 of 11 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41

丝印镭雕文件编号 客户号 DD2282(白色) 产品名称 W1126# 图纸编号 W1126-DD2282-00 22.9.29张琴魏娟 C/03 产品材质 表面工艺 无 ABS W1126-L-06(C/03) W1126-L-06(C/03) W1126-L-07(C/00) (变量，日期随生产日期而变动，22代表22号， 05代表5月，2022代表2022年， 字体为Arial，尺寸为10.6x1.5mm) W1126-E-05(C/00) W1126-L-07(C/00)(日期) 控制器表面印刷示意图 2.5mm 1.0mm 109.7mm 41mm 2.5mm 5.0mm 白色外壳印PANTONE BLACK C 黑色外壳印PANTONE WHITE C 22/05/2022 W1126-E-05(C/00) automateshades.com MT02-0101-067008-A AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 automateshades.com MT02-0101-067008-A AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 1.0mm 丝印镭雕文件编号 客户号 DD2282(黑色) 产品名称 W1126# 图纸编号 W1126-DD2282-00 C/03 产品材质 表面工艺 无 ABS W1126-L-05(C/03) W1126-L-05(C/03) 控制器表面印刷示意图 2.5mm 2.5mm 5.0mm 白色外壳印PANTONE BLACK C 黑色外壳印PANTONE WHITE C W1126-E-05(C/01) 109.7mm 41mm W1126-E-05(C/00) W1126-L-07(C/00) (变量，日期随生产日期而变动，22代表22号， 05代表5月，2022代表2022年， 字体为Arial，尺寸为10.6x1.5mm) 22/05/2022 22/05/2022 22.9.29张琴魏娟 W1126-L-07(C/00)(日期) automateshades.com MT02-0101-050008-A AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 DD/MM/YYYY automateshades.com MT02-0101-050008-A AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41

Internal Photos Documentation Manufacturer: Rollease Acmeda Inc Page 1 of 3 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 Internal Photos Documentation Manufacturer: Rollease Acmeda Inc Page 2 of 3 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 Antenna location Internal Photos Documentation Manufacturer: Rollease Acmeda Inc Page 3 of 3 Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41

Report No: 709502211930-00B EMC_SHA_F_R_02.06E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 1 of 4 Rev. 171.00 RF Exposure Estimation 1.Introduction Applicant:Rollease Acmeda Inc Address:7th Floor / 750 East Main Street, Stamford, CT 06902, USA Product:AUTOMATE | Push15 Channel Remote FCC ID:2AGGZ003B9ACA41 IC:21769-003B9ACA41 Model No.:MT02-0101-067008-A, MT02-0101-050008-A Reference RF report # 709502211930-00A 2.B.2 Blanket 1 mW Blanket Exemption The 1 mW Blanket Exemption of § 1.1307(b)(3)(i)(A) applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power of no more than 1 mW, regardless of separation distance. The 1 mW blanket exemption applies at separation distances less than 0.5 cm, including where there is no separation. This exemption shall not be used in conjunction with other exemption criteria other than those for multiple RF sources in paragraph § 1.1307(b)(3)(ii)(A). The 1 mW exemption is independent of service type and covers the full range of 100 kHz to 100 GHz, but it shall not be used in conjunction with other exemption criteria or in devices with higher-power transmitters operating in the same time-averaging period. Exposure from such higher-power transmitters would invalidate the underlying assumption that exposure from the lower-power transmitter is the only contributor to SAR in the relevant volume of tissue. 3.RF Exposure Evaluation Per the test report included herein, for 433.92MHz According to C63.10 Annex G EIRP = pt × gt =( E × d)2 /30, so pt=( E × d)2 /30* gt where pt is the transmitter output power in watts gt is the numeric gain of the transmitting antenna (dimensionless) E is the electric field strength in V/m d is the measurement distance in meters (m) transmitter output power for 433.92MHz Function Field strength (E):72.96 (dBuV/m) = 0.0044 (V/m) Measurement distance (D):3 (m) Antenna Gain, typical (dBi):3.0 Numerical gain of the transmit antenna (gt):2.0 Transmitter output power (TP):0.000003(W) Transmitter output power (TP):0.003(mW) Report No: 709502211930-00B EMC_SHA_F_R_02.06E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 2 of 4 Rev. 171.00 We used the maximum ERP/EIRP to perform RF exposure exemption evaluation. Evaluation methodExempt Limit (mW)Verdict n Blanket 1 mW Blanket Exemption1mWYes o MPE-based Exemption(ERP)7mW(ERP)N/A o SAR-based Exemption (Pth)3060mWN/A So, the device is qualified for SAR test exemption, the exemption report is in lieu of the SAR report. Report No: 709502211930-00B EMC_SHA_F_R_02.06E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 3 of 4 Rev. 171.00 Innovation, Science and Economic Development Canada (ISED) MPE / Health Hazard Requirement for the 433.92MHz According to Innovation, Science and Economic Development Canada (ISED) RSS-102 Issue 5, Section 2.5.1, SAR evaluation is required if the separation distance between the user and/or bystander and the antenna and/or radiating element of the device is less than or equal to 20 cm, except when the device operates at or below the applicable output power level (adjusted for tune-up tolerance) for the specified separation distance defined in Table 1. RESULTS Per the test report included herein, for 433.92MHz According to RSS-GEN (6.12 Transmitter output power), If the antenna is not detachable, field strength measurements shall be made using a test site that complies with the appropriate normative reference. Report No: 709502211930-00B EMC_SHA_F_R_02.06E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 4 of 4 Rev. 171.00 Frequency (MHz) Max. Field Strength (dBuV/m)@3m Antenna Gain (dBi) Maximum Antenna Gain (numeric) Max. Output Power (mW) Min. test separation distance (mm) 433.9272.96 (Note 1) 3.02.00.003 (Note 3) 5mm Note: 1. Field Strength (dBuV/m@3m) test result please refer to test report 709502211930-00A. 2. Output power (dBm) = where D is the distance in metres between the measurement antenna and the transmit antenna (of the EUT) and G is the numerical gain of the transmit antenna, referenced to isotropic gain, in dBi. 3. Output power (mW) = 10^ (Max power (dBm)/10) EIRP (PK) = 0.003mW < 52 mW (At separation distance of ≤5 mm) - TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch Reviewed by: Prepared by:Tested by: _____________________ ___________________________________________ Hui TONGWenqiang LUYiquan WANG EMCSectionManagerEMCProjectEngineerEMCTest Engineer Date: Dec. 02, 2022 Date: Dec. 02, 2022 Date: Dec. 02, 2022 -------------------------------------------------------End of Test Report--------------------------------------------------------------------

Report Number: 709502211930-00 EMC_SHA_F_R_02.05E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 1 of 20 Rev. 171.00 FCC/IC – TEST REPORT Report Number:709502211930-00Date of Issue: December 02, 2022 Model:MT02-0101-067008-A, MT02-0101-050008-A Product Type:AUTOMATE|Push15 Channel Remote Applicant: RolleaseAcmeda Inc Address: 7th Floor / 750 East Main Street, Stamford, CT 06902, USA Production Facility:Ningbo Dooya Mechanic & Electronic Technology Co.,Ltd Address: No.168 Shengguang Road,Luotuo,Zhenhai, 315202 Ningbo,Zhejiang province, :People's Republic of China Test Result:nPositiveoNegative Total pages including Appendices: 20 TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch is a subcontractor to TÜV SÜD Product Service GmbH according to the principles outlined in ISO 17025. TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch reports apply only to the specific samples tested under stated test conditions. Construction of the actual test samples has been documented. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. The manufacturer/importer is responsible to the Competent Authorities in Europe for any modifications made to the production units which result in non-compliance to the relevant regulations. TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch shall have no liability for any deductions, inferences or generalizations drawn by the client or others from TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch issued reports. This report is the confidential property of the client. As a mutual protection to our clients, the public and ourselves, extracts from the test report shall not be reproduced except in full without our written approval. dc Report Number: 709502211930-00 EMC_SHA_F_R_02.05E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 2 of 20 Rev. 171.00 1 Table of Contents 1 Table of Contents ................................................................................................ 2 2 Details about the Test Laboratory ....................................................................... 3 3 Description of the Equipment Under Test ........................................................... 4 4 Summary of Test Standards ............................................................................... 5 5 Summary of Test Results .................................................................................... 6 6 General Remarks ................................................................................................ 7 7 Systems test configuration .................................................................................. 8 8 Test Setups ......................................................................................................... 9 9 Test Methodology .............................................................................................. 10 9.1 Radiated Emission....................................................................................... 10 9.2 Bandwidth Measurement & 99% Occupied Bandwidth .............................. 14 9.3 Deactivation Time ........................................................................................ 16 10 Test Equipment List .......................................................................................... 17 11 System Measurement Uncertainty .................................................................... 18 12 Photographs of Test Set-ups ......................................................................... 19 13 Photographs of EUT ....................................................................................... 20 Report Number: 709502211930-00 EMC_SHA_F_R_02.05E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 3 of 20 Rev. 171.00 2 Details about the Test Laboratory Details about the Test Laboratory Test Site 1 Company name: TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch No.16 Lane, 1951 Du Hui Road, Shanghai 201108, P.R. China FCC Registration Number: 820234 Designation Number: CN1183 IC Company Number: 25988 CAB identifier:CN0101 Telephone:+86 21 6141 0123 Fax:+86 21 6140 8600 Report Number: 709502211930-00 EMC_SHA_F_R_02.05E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 4 of 20 Rev. 171.00 3 Description of the Equipment Under Test Product: AUTOMATE | Push15 Channel Remote Model no./HVIN: MT02-0101-067008-A, MT02-0101-050008-A FCC ID:2AGGZ003B9ACA41 IC:21769-003B9ACA41 Rating:3VDC RF Transmission Frequency: 433.92MHz Modulation:FSK Antenna Type:PCB antenna Antenna Gain:3.0 dBi max (Declared by manufacturer) Description of the EUT:The Equipment Under Test (EUT) is a transmitter operated at 433.92MHz. Test sample no.:SHA-631950-1 Report Number: 709502211930-00 EMC_SHA_F_R_02.05E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 5 of 20 Rev. 171.00 4 Summary of Test Standards Test Standards FCC Part 15 Subpart CPART 15 - RADIO FREQUENCY DEVICES Subpart C - Intentional Radiators RSS-Gen Issue 5 Amendment 2 February 2021 General Requirements for the Certification of Radio Apparatus RSS-210 Issue 10 December 2019 RSS-210 — Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment All the test methods were according to ANSI C63.10-201…

Text truncated - open the document above for the full version.

Antenna Information To whom it may concern, Product name: AUTOMATE | Push15 Channel Remote Model: MT02-0101-067008-A, MT02-0101-050008-A FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 The applicable FCC and ISED rule part of this product is § 15.231 and RSS-210, radiated measurements are used to show compliance with FCC and ISED limits for fundamental and spurious emissions. The Antenna information as below for your reference. Antenna photo:PCB Layout Antenna transmission frequency: 433.92MHz Antenna type: PCB antenna Antenna Gain: 3.0dBi Yours sincerely, Name: Jonny Matuichuk Company name: Rollease Acmeda Inc Address: 750 East Main Street, 7th Floor, Stamford CT 06902, USA Title: Product Manager - Motorization E‐mail: [email protected] Tel: +1 203 832 6756 Signature:

Manufacturer: Rollease Acmeda Inc Product: AUTOMATE | Push15 Channel Remote FCC ID: 2AGGZ003B9ACA41 IC: 21769-003B9ACA41 2023 Not to be reproduced, except in its entirety,Page 1 of 1 without the Permission of TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch PHOTOGRAPHS OF TEST SET UP Field Strength and Harmonics Test Setup Radiated Emission Setup 30MHz ~ 1GHz Above 1GHz