2AGGZ003B9ACA44DC 2.0Nm ARC Motor

Li-ion & DC Motor MOTOR PROGRAMMING INSTRUCTIONS SOFT STOP SOLAR OPTION FAVORITE POSITION SELECTABLE SPEED BATTERY POWERED USB CHARGE (Only for Li-ion Motor) ELECTRONIC LIMIT LEVEL CONTROL BATTERY CHECK433 MHZ BI-DIRECTIONAL AUTOMATE 5V ZERO & WIREFREE V1.0_PRGM_JULY_2022 Fav Position Live Feedback Energy ecient 2 | Automate ™ Programming Instructions | Li-ion & DC Motors ROLLEASE ACMEDA SAFETY INSTRUCTIONS WARNING: Important safety instructions to be read before installation. Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty. WARNING: Important safety instructions to be read before installation and use. It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference. WARNING: Incorrect installation or use can lead to serious injury and will void manufacturer’s liability and warranty. • Read and follow all installation and safety instructions. • This manual is also available on the website. • Do not expose to water, moisture, humid and damp environments or extreme temperatures. • Use or modification outside the scope of this instruction manual will void warranty. • This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children should not play with the appliance. Cleaning and user maintenance should not be performed by children without supervision. • Do not allow children to play with fixed controls. Keep appliance and remote controls away from children. • Assembly, installation and programming must be performed by a suitably qualified installer. • For use with motorized shading devices. • Frequently inspect the installation for improper operation, signs of wear, imbalance or damage to cables or springs. Do not use if repair or adjustment is necessary. • The appliance must be disconnected from its power source during cleaning, maintenance or when replacing parts. Maintenance and parts replacement should be performed by a suitably qualified installer/technician. • The A-weighted emission sound pressure level of the appliance is less than or equal to 70dB(A). • The appliance is for indoor use only. • Disconnect the appliance from power or switch off automatic controls when maintenance, such as window cleaning, is being carried out in the vicinity. • The appliance must be supplied only the safe, extra-low voltage corresponding to the marking on the appliance. • Keep clear of the appliance when in operation. • There are no user serviceable parts or batteries inside the appliance. • Remote batteries should be replaced with the correctly specified type only. • The mass and dimensions of the driven part must be compatible with the rated torque and rated operating time of the appliance. • The driven part must be compatible with the rated torque and operating time of the appliance as follows: For 0.5Nm motor series (MT01-1320-069001 and similar): Rated torque of 0.5Nm, rated operating time of 12 minutes and minimum tube diameter of ø20mm. For 1.1Nm motor series (MT01-1325-069002, MT01-1225-069002 and similar): Rated torque of 1.1Nm, rated operating time of 12 minutes and minimum tube diameter of ø25mm. For 2.0Nm motor series (MT01-1328-069001, MT01-1228-069002 and similar): Rated torque of 2.0Nm, rated operating time of 12 minutes and minimum tube diameter of ø28mm. • Fixed controls have to be clearly visible after installation. • The appliance is intended to be installed at a height of at least 2.5m above the floor or any other accessible level surface. • Before installing the appliance, remove any unnecessary cords or components and disable any equipment not needed for powered operation. ROLLEASE ACMEDA Automate ™ Programming Instructions | Li-ion & DC Motors | 3 COMPLIANCE STATEMENT This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. To satisfy FCC / IC RF exposure requirements, a separation distance o…

Text truncated - open the document above for the full version.

1 of 1 To whom it may concern, Letter of Declaration We, Rollease Acmeda Inc, hereby declare the models below: Model(S): MT01‐1228‐069002‐A, MT01‐1225‐069003‐A FCC ID: 2AGGZ003B9ACA44 IC: 21769‐003B9ACA44 are identical in electrical and mechanical construction except for the end‐cap adaptor. For the end cap adaptor, the only change is the adaptor’s profile as shown in the below table: Product Code Bill of Materials Adapter Fitted Image of Motor MT01‐1228‐ 069002‐A MT01‐1228‐ 069003‐A Yours sincerely, Signature: Print name: Jonny Matuichuk Title: Product Manager Date: 16/11/2022

ExternalPhotosDocumentation Manufacturer:Rollease Acmeda IncPage1of2 Product:DC 2.0Nm ARC Motor FCC ID:2AGGZ003B9ACA44 IC: 21769-003B9ACA44 ExternalPhotosDocumentation Manufacturer:Rollease Acmeda IncPage2of2 Product:DC 2.0Nm ARC Motor FCC ID:2AGGZ003B9ACA44 IC: 21769-003B9ACA44 MT01-1228-069003-Aouter cover MT01-1228-069002-Aouter cover

label position

Internal Photos Documentation Manufacturer: Rollease Acmeda Inc Page 1 of 8 Product: DC 2.0Nm ARC Motor FCC ID: 2AGGZ003B9ACA44 IC: 21769-003B9ACA44 Internal Photos Documentation Manufacturer: Rollease Acmeda Inc Page 2 of 8 Product: DC 2.0Nm ARC Motor FCC ID: 2AGGZ003B9ACA44 IC: 21769-003B9ACA44 Internal Photos Documentation Manufacturer: Rollease Acmeda Inc Page 3 of 8 Product: DC 2.0Nm ARC Motor FCC ID: 2AGGZ003B9ACA44 IC: 21769-003B9ACA44 Internal Photos Documentation Manufacturer: Rollease Acmeda Inc Page 4 of 8 Product: DC 2.0Nm ARC Motor FCC ID: 2AGGZ003B9ACA44 IC: 21769-003B9ACA44 Internal Photos Documentation Manufacturer: Rollease Acmeda Inc Page 5 of 8 Product: DC 2.0Nm ARC Motor FCC ID: 2AGGZ003B9ACA44 IC: 21769-003B9ACA44 Internal Photos Documentation Manufacturer: Rollease Acmeda Inc Page 6 of 8 Product: DC 2.0Nm ARC Motor FCC ID: 2AGGZ003B9ACA44 IC: 21769-003B9ACA44 Internal Photos Documentation Manufacturer: Rollease Acmeda Inc Page 7 of 8 Product: DC 2.0Nm ARC Motor FCC ID: 2AGGZ003B9ACA44 IC: 21769-003B9ACA44 Internal Photos Documentation Manufacturer: Rollease Acmeda Inc Page 8 of 8 Product: DC 2.0Nm ARC Motor FCC ID: 2AGGZ003B9ACA44 IC: 21769-003B9ACA44 Antenna

Report No:709502211928-00B EMC_SHA_F_R_02.06E TÜV SÜDCertification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page1of4 Rev. 171.00 RFExposureEstimation 1.Introduction Applicant:Rollease Acmeda Inc Address:7th Floor / 750 East Main Street, Stamford, CT 06902, USA Product:DC2.0Nm ARC Motor FCC ID:2AGGZ003B9ACA44 IC:21769-003B9ACA44 Model No.:MT01-1228-069002-A, MT01-1228-069003-A Reference RF report # 709502211928-00A 2.B.2 Blanket 1 mW Blanket Exemption The 1 mW Blanket Exemption of § 1.1307(b)(3)(i)(A) applies for single fixed, mobile, and portable RF sources with available maximum time-averaged power of no more than 1 mW, regardless of separation distance. The 1 mW blanket exemption applies at separation distances less than 0.5 cm, including wherethere is no separation. This exemption shall not be used in conjunction with other exemption criteria other than those for multiple RF sources in paragraph § 1.1307(b)(3)(ii)(A). The 1 mW exemption is independent of service type and covers the full range of 100 kHz to 100 GHz, but it shall not be used in conjunction with other exemption criteria or in devices with higher-power transmitters operating in the same time-averaging period. Exposure from such higher-power transmitters would invalidate the underlying assumption that exposure from the lower-power transmitter is the only contributor to SAR in the relevant volume of tissue. 3.RF Exposure Evaluation Per the test report included herein,for 433.925MHz According to ANSI C63.10-2013 (9.5Equations to calculate EIRP), Report No:709502211928-00B EMC_SHA_F_R_02.06E TÜV SÜDCertification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page2of4 Rev. 171.00 Frequency (MHz) Max. Field Strength (dBuV/m)@3m Max. Output Power (dBm) Max. Output Power (mW) Min. test separation distance (mm) 433.92583.48 (Note 1) -11.68 (Note 2) 0.068 (Note 3) 5mm Note: 1. FieldStrength (dBuV/m@3m) test result please refer to test report709502211928-00A. 2. Output power (dBm) = Field Strength (dBuV/m)@3m+20log(Distance=3meter)–104.7. 3. Output power (mW) = 10^ (Max power (dBm)/10) We used the maximum ERP/EIRP toperform RF exposure exemption evaluation. Evaluation methodExempt Limit(mW)Verdict n Blanket 1 mW Blanket Exemption1mWYes o MPE-based Exemption(ERP)7mW(ERP)N/A o SAR-based Exemption(Pth)3060mWN/A So, the device is qualified for SARtest exemption, the exemption report is in lieu of the SAR report. Report No:709502211928-00B EMC_SHA_F_R_02.06E TÜV SÜDCertification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page3of4 Rev. 171.00 Innovation, Science and Economic DevelopmentCanada (ISED) MPE / Health Hazard Requirement for the433.925MHz According to Innovation, Science and Economic DevelopmentCanada (ISED) RSS-102 Issue 5, Section 2.5.1, SAR evaluation is required if the separation distance between the user and/or bystander and the antenna and/or radiating element of the device is less than or equal to 20 cm, except when the device operates at or below the applicable output power level (adjusted for tune-up tolerance) for the specified separation distance defined in Table 1. RESULTS Per the test report included herein,for433.925MHz According toRSS-GEN(6.12 Transmitter output power), If the antenna is not detachable, field strength measurements shall be made using a test site that complies with the appropriate normative reference. Report No:709502211928-00B EMC_SHA_F_R_02.06E TÜV SÜDCertification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page4of4 Rev. 171.00 Frequency (MHz) Max.Field Strength (dBuV/m)@3m Antenna Gain (dBi) Maximum Antenna Gain (numeric) Max. Output Power (mW) Min. test separation distance (mm) 433.92583.48 (Note 1) 0.51.120.060 (Note 3) 5mm Note: 1. Field Strength (dBuV/m@3m) test result please refer to test report709502211928-00A. 2. Output power (dBm) = where D is the distance in metres between the measurement antenna and the transmit antenna (of the EUT) and G is the numerical gain of the transmit antenna, referenced to isotropic gain, in dBi. 3. Output power (mW) = 10^ (Max power (dBm)/10) EIRP (PK)=0.060mW <52mW (At separation distance of ≤5 mm) -TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch Reviewed by:Prepared by:Tested by: ________________________________________________________________ Hui TONGWenqiang LUHuili CHENG EMCSectionManagerEMCProjectEngineerEMCTest Engineer Date:Dec.02,2022Date:Dec.02,2022Date:Dec.02, 2022 -------------------------------------------------------End of Test Report--------------------------------------------------------------------

Report Number: 709502211928-00A EMC_SHA_F_R_02.05E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 1 of 20 Rev. 171.00 FCC/IC – TEST REPORT Report Number:709502211928-00ADate of Issue: October 12, 2022 Model:MT01-1228-069002-A, MT01-1228-069003-A Product Type:DC 2.0Nm ARC Motor Applicant:Rollease Acmeda Inc Address:7th Floor / 750 East Main Street, Stamford, CT 06902, USA Production Facility:Ningbo Dooya Mechanic & Electronic Technology Co.,Ltd Address: No.168 Shengguang Road,Luotuo,Zhenhai, 315202 Ningbo,Zhejiang Province :People'sRepublic of China Test Result:nPositiveoNegative Total pages including Appendices: 20 TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch is a subcontractor to TÜV SÜD Product Service GmbH according to the principles outlined in ISO 17025. TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch reports apply only to the specific samples tested under stated test conditions. Construction of the actual test samples has been documented. It is the manufacturer's responsibility to assure that additional production units of this model are manufactured with identical electrical and mechanical components. The manufacturer/importer is responsible to the Competent Authorities in Europe for any modifications made to the production units which result in non-compliance to the relevant regulations. TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch shall have no liability for any deductions, inferences or generalizations drawn by the client or others from TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch issued reports. This report is the confidential property of the client. As a mutual protection to our clients, the public and ourselves, extracts from the test report shall not be reproduced except in full without our written approval. dc Report Number: 709502211928-00A EMC_SHA_F_R_02.05E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 2 of 20 Rev. 171.00 1 Table of Contents 1 Table of Contents ................................................................................................ 2 2 Details about the Test Laboratory ....................................................................... 3 3 Description of the Equipment Under Test ........................................................... 4 4 Summary of Test Standards ............................................................................... 5 5 Summary of Test Results .................................................................................... 6 6 General Remarks ................................................................................................ 7 7 Systems test configuration .................................................................................. 8 8 Test Setups ......................................................................................................... 9 9 Test Methodology .............................................................................................. 10 9.1 Radiated Emission....................................................................................... 10 9.2 Bandwidth Measurement & 99% Occupied Bandwidth .............................. 14 9.3 Deactivation Time ........................................................................................ 16 10 Test Equipment List .......................................................................................... 17 11 System Measurement Uncertainty ................................................................. 18 12 Photographs of Test Set-ups ......................................................................... 19 13 Photographs of EUT ....................................................................................... 20 Report Number: 709502211928-00A EMC_SHA_F_R_02.05E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 3 of 20 Rev. 171.00 2 Details about the Test Laboratory Details about the Test Laboratory Test Site 1 Company name: TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch No.16 Lane, 1951 Du Hui Road, Shanghai 201108, P.R. China FCC Registration Number: 820234 Designation Number: CN1183 IC Company Number: 25988 CAB identifier:CN0101 Telephone:+86 21 6141 0123 Fax:+86 21 6140 8600 Report Number: 709502211928-00A EMC_SHA_F_R_02.05E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 4 of 20 Rev. 171.00 3 Description of the Equipment Under Test Product:DC 2.0Nm ARC Motor Model no./HVIN:MT01-1228-069002-A, MT01-1228-069003-A FCC ID:2AGGZ003B9ACA44 IC:21769-003B9ACA44 Rating:12VDC RF Transmission Frequency: 433.925MHz Modulation:FSK Antenna Type:Line antenna Antenna Gain:0.5 dBi max (Declared by manufacturer) Description of the EUT:The Equipment Under Test (EUT) is a transceiver operated at 433.925MHz. Test sample no.:SHA-665325-3 Report Number: 709502211928-00A EMC_SHA_F_R_02.05E TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch 3-13, No.151, Heng Tong Road, Shanghai, 200070, P.R. China Phone: +86 21 61410123, Fax:+86 21 61408600 Page 5 of 20 Rev. 171.00 4 Summary of Test Standards Test Standards FCC Part 15 Subpart CPART 15 - RADIO FREQUENCY DEVICES Subpart C - Intentional Radiators RSS-Gen Issue 5 Amendment 2 February 2021 General Requirements for the Certification of Radio Apparatus RSS-210 Issue 10 December 2019 RSS-210 — Licence-exempt Radio Apparatus (All Frequency Bands): Category I Equipment All the test methods were according to ANSI C63.10-2013. Report Number: 7095022…

Text truncated - open the document above for the full version.

 Antenna Information To whom it may concern, Product name:DC 2.0Nm ARC Motor Model:MT01-1228-069002-A, MT01-1228-069003-A FCC ID: 2AGGZ003B9ACA44, IC: 21769-003B9ACA44 The applicable FCC and ISED rule part of this product is § 15.231 and RSS-210,radi- ated measurements are used to show compliance with FCC and ISED limits for fundamental and spurious emissions. The Antenna information as below for your reference. Antenna photo: Antenna transmission frequency: 433.925MHz Antenna type: Line antenna Antenna Gain: 0.5dBi Yours sincerely, Name:JonnyMatuichuk Companyname: RolleaseAcmeda Inc Address: 750 East Main Street, 7th Floor, Stamford CT 06902, USA Title: Product Manager -Motorization E‐mail: [email protected] Tel:+1 2038326756

Manufacturer: Rollease Acmeda Inc Product: DC 2.0Nm ARC Motor FCC ID: 2AGGZ003B9ACA44 IC: 21769-003B9ACA44 2022 Not to be reproduced, except in its entirety,Page 1 of 1 without the Permission of TÜV SÜD Certification and Testing (China) Co., Ltd. Shanghai Branch PHOTOGRAPHS OF TEST SET UP Field Strength and Harmonics Test Setup Radiated Emission Setup 30MHz ~ 1GHz Above 1GHz