2AHCR-R20AV5Door Phone

About This Manual Thank you for choosing Akuvox R20A V5.0 door phone. This manual is intended for the administrators who need to properly configure the door phone. This manual applies to320.30.3.18 and it provides all the configurations for the functions and features of Akuvox door phone. Please visit Akuvox forum or consult technical support for any new information or latest firmware. Introduction of Icons and Symbols Note:  Informative information and advice from the efficient use of the device. Caution:  Always abide by this information in order to prevent the damages to the device. Warning:  Always abide by this information in order to prevent the persons from injury. Related Documentation You are advised to refer to the related documents for more technical information via the link below: https://knowledge.akuvox.com Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator&you body. Table of Contents 1. Product Overview ...................................................................................... 1 2. Change Log .............................................................................................. 2 3. Model Specification ................................................................................... 3 4. Introduction to Configuration Menu ............................................................ 4 5. Access the Device .................................................................................... 8 5.1. Obtain Device IP Address .................................................................. 8 5.2. Access the Device Setting on the Web Interface ............................... 9 6. Language and Time Setting .................................................................... 10 6.1. Language Setting ............................................................................. 10 6.2. Time Setting ..................................................................................... 11 7. LED Setting ............................................................................................ 13 7.1. Infrared LED Setting ........................................................................ 13 7.2. LED Display Status .......................................................................... 14 7.3. Setup LED Display from HTTP URL ................................................ 16 7.4. LED Setting on Card Reader Area ................................................... 17 8. Volume and Tone Configuration .............................................................. 19 8.1. Volume Configuration ...................................................................... 19 8.2. IP Announcement ............................................................................ 21 8.3. Open Door Tone Configuration ........................................................ 21 8.4. Upload Tone Files ............................................................................ 23 8.4.1. Upload Ringback Tone .......................................................... 23 8.4.2. Upload Open Door Tone ........................................................ 23 9. Network Setting ...................................................................................... 26 9.1. Network Status ................................................................................ 26 9.2. Device Network Configuration ......................................................... 26 9.3. Device Deployment in Network ........................................................ 28 9.4. Device Local RTP configuration ....................................................... 30 9.5. NAT Setting ..................................................................................... 31 9.6. SNMP Setting .................................................................................. 33 9.7. VLAN Setting ................................................................................... 34 9.8. TR069 Setting .................................................................................. 35 9.9. Device Web HTTPSetting ................................................................ 37 10. Intercom Call Configuration .............................................…

Text truncated - open the document above for the full version.

QA-FR-170-B Company: AKUVOX (XI AMEN) NETWORKS CO., LTD. Add: 10/F, No.56 Guanri Road, Software Park II, Xiamen 361009, China Tel: 086-0591-83057798 Fax: 086-0591-83057798 Email: [email protected] FCC Authorization Date: 2022-09-02 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , AKUVOX (XIAMEN) NETWORKS CO., LTD., Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s signature Printed Name: Bo Yang Title: Manager

QA -FR-171-A AKUVOX (XIAMEN) NETWORKS CO., LTD. Add: 10/F, No.56 Guanri Road, Software Park II, Xiamen 361009, China Tel: 086-0591-83057798 Fax: 086-0591-83057798 Email: [email protected] FCC Confidential Authorization D ate: 2022-09-02 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 S ubject: Confidentiality Request regarding application for certification of FCC ID: 2AHCR-R20AV5 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, AKUVOX (XIAMEN) NETWORKS CO., LTD. hereby requests long-term confidential treatment of information accompanying this application as outlined below: •Block Diagram •Schematics •Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. S incerely, S ignature: Printed Name: Bo Yang Title: Manager

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS Port RFID Antenna NFC Antenna Chip1 Chip2 Chip3

TEST REPORT Applicant: AKUVOX (XIAMEN) NETWORKS CO., LTD. Address: 10/F, No.56 Guanri Road, Software Park II, Xiamen 361009, China FCC ID: 2AHCR-R20AV5 Product Name: Door Phone Model Number: R20A Standard(s): 47 CFR Part 15, Subpart C ANSI C63.10-2013 The above equipment has been tested and found compliance with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR22060019-00B Date Of Issue: 2022-08-25 Reviewed By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR22060019-00B Page 2 of 38 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR22060019-00B Page 3 of 38 CONTENTS TEST FACILITY ............................................................................................................................................................. 2 DECLARATIONS ............................................................................................................................................................ 2 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 4 1.2 DESCRIPTION OF TEST CONFIGURATION ................................................................................................................ 5 1.2.2 Support Equipment List and Details .............................................................................................................. 5 1.2.3 Support Cable List and Details ...................................................................................................................... 5 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 6 1.2.2 Support Equipment List and Details .............................................................................................................. 6 1.2.3 Support Cable List and Details ...................................................................................................................... 6 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 7 1.3 MEASUREMENT UNCERTAINTY .............................................................................................................................. 9 2. SUMMARY OF TEST RESULTS ......................................................................................................................... 10 3. REQUIREMENTS AND TEST PROCEDURES ................................................................................................. 11 3.1 AC LINE CONDUCTED EMISSIONS ........................................................................................................................ 11 3.1.1 Applicable Standard ..................................................................................................................................... 11 3.1.2 EUT Setup.................................................................................................................................................... 12 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 12 3.1.4 Test Procedure ............................................................................................................................................. 13 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 13 3.2 RADIATION SPURIOUS EMISSIONS ........................................................................................................................ 14 3.2.1 Applicable Standard ..................................................................................................................................... 14 3.2.2 EUT Setup.................................................................................................................................................... 14 3.2.3 EMI Test Receiver & Spectrum Analyzer Setup ......................................................................................... 15 3.2.4 Corrected Amplitude & Margin Calculation ...................................…

Text truncated - open the document above for the full version.

TEST REPORT Applicant: AKUVOX (XIAMEN) NETWORKS CO., LTD. Address: 10/F, No.56 Guanri Road, Software Park II, Xiamen 361009, China FCC ID: 2AHCR-R20AV5 Product Name: Door Phone Model Number: R20A Standard(s): 47 CFR Part 15, Subpart C(15.225) ANSI C63.10-2013 The above equipment has been tested and found compliance with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR22060019-00C Date Of Issue: 2022-08-25 Reviewed By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR22060019-00C Page 2 of 49 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR22060019-00C Page 3 of 49 CONTENTS T EST FACILITY .......................................................................................................................................... 2 DECLARATIONS .......................................................................................................................................... 2 1. GENERAL INFORMATION .................................................................................................... 4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................... 4 1.2 DESCRIPTION OF TEST CONFIGURATION ........................................................................................... 5 1.2.2 Support Equipment List and Details .............................................................................................................. 5 1.2.3 Support Cable List and Details ...................................................................................................................... 5 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 6 1.3 MEASUREMENT UNCERTAINTY .......................................................................................................... 8 2. SUMMARY OF TEST RESULTS ............................................................................................ 9 3. REQUIREMENTS AND TEST PROCEDURES .................................................................. 10 3.1 AC LINE CONDUCTED EMISSIONS .................................................................................................... 10 3.1.1 Applicable Standard ..................................................................................................................................... 10 3.1.2 EUT Setup.................................................................................................................................................... 11 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 11 3.1.4 Test Procedure ............................................................................................................................................. 12 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 12 3.2 RADIATED EMISSIONS ....................................................................................................................... 13 3.2.1 Applicable Standard ..................................................................................................................................... 13 3.2.2 EUT Setup.................................................................................................................................................... 13 3.2.3 EMI Test Receiver & Spectrum Analyzer Setup ......................................................................................... 14 3.2.4 Corrected Amplitude & Margin Calculation ................................................................................................ 14 3.3 20 DB EMISSION BANDWIDTH: .......................................................................................................... 15 3.3.1 Applicable Standard ..................................................................................................................................... 15 3.3.2 EUT Setup.................................................................................................................................................... 15 3.3.3 Test Procedure ..................................................................................................................................…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions Front View –Adapter mode Conducted Emissions Side View –Adapter mode Conducted Emissions Front View –POE mode Conducted Emissions Side View –POE mode Radiated Emission 9kHz-30MHz Parallel View –Adapter mode Radiated Emission 9kHz-30MHz Perpendicular View –Adapter mode Radiated Emission 9kHz-30MHz Ground-parallel View –Adapter mode Radiated Emission 30MHz-1GHz View –Adapter mode Radiated Emission 9kHz-30MHz Parallel View –POE mode Radiated Emission 9kHz-30MHz Perpendicular View –POE mode Radiated Emission 9kHz-30MHz Ground-parallel View –POE mode Radiated Emission 30MHz-1GHz View –POE mode