2AIOC-1661Wireless Charger Mat

Wireless Charger Mat HKWP1661-10E Manufacture: HANK ELECTRONICS CO.,LTD. Address: Floor 2nd-7th, A8, Hongye Industry City, Zhou shi Road , Baoan District ,shenzhen China LED 26.6mm 76.5mm 37.2mm Product Parameter Input Output N.W Product Size Precau�ons 1. Don't use & store this charger under humid environment. 2. Working tempreture: within 0 ~ +25 . 3. Keep it away from children. 4. Avoid thunder strike. 5. Pull out the plug a�er fully charged. DC 12V-24V Output 1: 5V/2.4A Output 2(QC 3.0): 5V/3A, 9V/2A, 12V/1.5A 27g 26.6*37.2*82.1mm 82.1mm Product Parameter Instruc�on Input Output N.W Frequency range Product Size Accessories LED IndicatorStatus Power On Standby Charging Abnormaity(OTP, FOD,OVP) Full Charge Indicator Power on for 3 seconds, then off White led off White led on White led flash quickly White led on 1. Charge: Connect the Wireless charger into car socket with cable. LED Indicator 1. LED Indicator: White 2. Lay the device on the wireless charger for charging. · Do not expose the charger to sources of excessive heat, such as sunlight, fire etc. Do not place the charger near open fire sources, such as gas burners, candles or fireplaces, and avoid contact with direct solar radia�on. Do not place any candles or other open-flame sources on the device. Make sure that the charger has sufficient ven�la�on. Accesories and So�ware Informa�on It is recommended that the following accessories should be used: The product so�ware version is REV:01 So�ware updates will be released by the manufacturer to fix bugs or enhance func�ons a�er the product has been released. All so�ware versions released by the manufacturer have been verified and are s�ll compliant with the related rules. All RF parameters(for example, frequency range and ouput power) are not accessible to the user, and cannot be changed by the user. EU regulatory conformance Frequency bands and power (a) Frequency bands 110-205 KHz. (b) Maximum radio- frequency power transmi�ed in the frequency bands in which the radio equipment operates: The maximum power for all bands is less than the highest limit value specified in the related Harmonized Standard. The frequency bands and transmi�ng power(radiated and/or conducted) nominal limits applicable to this radio equipment are as follows: 38.08 dBuA/m at 3m. DECLARATION CONFORMITY Hereby, HANK Electronics Co., Ltd. declares that the equipmemt type is in compliance with Direc�ve 2014/53/EU. The full text of the EU declara�on of conformity is available at the following internet address h�p://www.hank-tech.com Manufacturer: HANK Electronics Co., Ltd. Manufacturer's Address: Floor 2nd-7th, A8, Hongye Industry City, Lezhujiao, Zhoushi Road, Baoan District, Shenzhen,China. The Product shall be powered by external power supply or other 5V DC source, which shall comply with LPS requirement of IEC/EN 62368-1. This product can be powered through a micro USB from any CE compliant power source that implement the European interface as requested by (EN 301 489-52) Warning Fire and Electric Shock Hazard · Do not expose the charger to liquid, moisture, humidity, or rain. Do not use the charger near a bathtub, sink, sauna, pool, or steam room, Exposing of the charger to moisture could result in electric shock. · Do not drop, disassemble, open, crush, bend, deform, puncture, shred, microwave, incinerate, paint or insert foreign objects into the charger. Such ac�ons could result in electric shock. · Clean the charger only with a dry cloth. · Do not expose the charger wot extreamly high or low tempretures. DC 5V/2A, 9V/1.67A 10W Max 300g 110-205KHz 188.5*103.5*24.9mm Car charger, cable Precau�ons 1. Only charge mobile phones that are Qi-compa�ble. 2. Don't disassemble this charger privately. 3. Handle with care and avoid falling on the ground. 4. Don't place heavy objects on it. 5. Children should be supervised to use these products. 6. Charger working temperature : 025. Envir onment that has direct sunlight, near hea�ng equipment or in high temperature is forbidden. 7. Don't place metal foreign material between mobile phone and this charger. 103.5mm 24.9mm 188.5mm Car cigarette lighter DC12-24V Car Charger HKDP0019-30Q 3. the wireless mat Put it on the front of the car or on the central console. Hereby, HANK Electronics Co.,Ltd. declares that the equipment type HKWP1661-10E in compliance with Direc�ve 2014/53/EU. The full text of the EU declara�on of conformity is available at the following internet address: h�p://www.hank-tech.com Importer: XXX Address : XXX FCC NOTICE(for USA) This device complies with 15 of the FCC Rules. Opera�on is subject to the following two condi�ons: (1) This device may not cause harmful interference (2) This device must accept any interference received. including interference that may cause undesired opera�on. The manufacturer is not responsilble for any radio or tv interference caused by unauthorized modifica�ons or change to this equipment. Such modifica�ons or change could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a class B digital device. pursuant to part 15 of the FCC Rules. These limits are designed to provided reasonable protec�on against harmful interference in a residen�al installa�on. This equipment generates, users and can radiate radio frequency energy and, if not installed and used in accordance with the instruc�ons, may cause harmful interference to radio communica�ons. However, there is no guarantee that interference will not occur in a par�cular installa�on. If this equipment does cause harmful interference to radio or televison recep�on, which can be determined by turning the euipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separa�on between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the…

Text truncated - open the document above for the full version.

HANK ELECTRONICS CO., LTD. Date: 2019-11-5 TO: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID:2AIOC-1661 To whom it may concern: We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branchand Joyce Shi in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branchto act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides withHANK ELECTRONICS CO., LTD. This authorization is valid until further written notice from the applicant. Print Name: GuangCan YangTitle: Program Manager Signature: On behalf of Company: HANK ELECTRONICS CO., LTD. Telephone: 0755-82024967 Fax: 0755-82025852 E-mail: [email protected]

HANK ELECTRONICS CO., LTD. To: SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia United States From:HANK ELECTRONICS CO., LTD. Floor 2nd-7th,A8,Hongye Industry City Lezhujiao, Zhoushi Road,Baoan District, Shenzhen, China Regarding: Confidentiality Request regarding application for FCC ID: 2AIOC-1661 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commission’s rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic Block Diagram Operational Description The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. Sincerely, Print Name: GuangCan YangTitle: Program Manager Signature: On behalf of Company: HANK ELECTRONICS CO., LTD. Telephone: 0755-82024967 E-mail: [email protected]

HANK ELECTRONICS CO., LTD. Cover Letter-Wireless Charger Approval FCC ID: 2AIOC-1661Date: 2019-11-05 Gentlemen: There’s a Wireless Charger Mat that would like to have your authorization as an Inductive wireless power transfer applications approval. The specific product as below, Wireless Charger Mat, with its designed features and specified description, meets special requirements for KDB 680106 D01 section 5.2 requirements. Company:HANK ELECTRONICS CO., LTD. Product Name: Wireless Charger Mat Model Number: HKWP1661-10E FCC ID:2AIOC-1661 KDB 680106 D01 Section 5.2 Requirements:Product Technical Specification：Result: a) Power transfer frequency is less than 1 MHzComplied b) Output power from each primary coil is less than or equal to 15 watts. Complied c) The transfer system includes only single primary and secondary coils. This includes charging systems that may have multiple primary coils and clients that are able to detect and allow coupling only between individual pairs of coils Complied d) Client device is placed directly in contact with the transmitter. Complied e) Mobile exposure conditions only (portable exposure conditions are not covered by this exclusion) Complied f) The aggregate H-field strengths at 15 cm surrounding the device and 20 cm above the top surface from all simultaneous transmitting coils are demonstrated to be less than 50% of the MPE limit. Please refer to RF exposure reportComplied Sincerely, Print Name: GuangCan YangTitle: Program Manager Signature: On behalf of Company: HANK ELECTRONICS CO., LTD. Telephone: 0755-82024967 E-mail: [email protected] 111.058-140.545 kHz 10 watts Max

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 7 External Photos for SZEM1910019770CR FCC ID: 2AIOC-1661 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 7 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 6 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 7 of 7

Wireless Charger Mat HKWP1661-10E Input: DC 5V/2A, 9V/1.67A Output: 10W Max Made in China FCC ID:2AIOC-1661 This device complies with part 15 of the FCC Rules.Operation is subject to the following two condions: (1) This device may not cause harmful interference,and (2) This device must accept any interference received, including interference that may cause undesired operation.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 5 Internal Photos for SZEM1910019770CR FCC ID: 2AIOC-1661 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 5 1 EUT Constructional Details SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 5 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 5 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 5

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191001977002 Page: 1 of 23 Keny Xu EMC Laboratory Manager 1 COVER PAGE Human Exposure Report Application No.: SZEM1910019770CR Applicant: HANK ELECTRONICS CO., LTD. Address of Applicant: Floor 2nd-7th, A8, Hongye Industry City Lezhujiao, Zhoushi Road, Baoan District, Shenzhen, China Manufacturer: HANK Electronics Co., Ltd. Address of Manufacturer: Floor 2nd-7th, A8, Hongye Industry City, Lezhujiao, Zhoushi Road, Baoan District, Shenzhen, China Factory: HANK Electronics Co., Ltd. Address of Factory: Floor 2nd-7th, A8, Hongye Industry City, Lezhujiao, Zhoushi Road, Baoan District, Shenzhen, China Equipment Under Test (EUT): EUT Name: Wireless Charger Mat Model No.: HKWP1661-10E FCC ID: 2AIOC-1661 Standards: 47 CFR PART 1, Subpart I, Section 1.1310 Date of Receipt: 2019-10-31 Date of Test: 2019-11-11 to 2019-11-14 Date of Issue: 2019-11-19 Test Result : Pass* * In the configuration tested, the EUT complied with the standards specified above SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191001977002 Page: 2 of 23 Revision Record Version Chapter Date Modifier Remark 01 2019-11-19 Original Authorized for issue by: Bill Chen /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191001977002 Page: 3 of 23 2 Contents 1 COVER PAGE ......................................................................................................................................................... 1 2 CONTENTS .............................................................................................................................................................. 3 3 GENERAL INFORMATION ................................................................................................................................... 4 3.1 DETAILS OF E.U.T. ................................................................................................................................................. 4 3.2 DESCRIPTION OF SUPPORT UNITS ........................................................................................................................... 4 3.3 TEST LOCATION ...................................................................................................................................................... 5 3.4 TEST FACILITY ....................................................................................................................................................... 5 3.5 DEVIATION FROM STANDARDS ............................................................................................................................... 5 3.6 ABNORMALITIES FROM STANDARD CONDITIONS .................................................................................................... 5 4 EQUIPMENTS USED DURING TEST .................................................................................................................. 6 5 TEST RESULTS ...................................................................................................................................................... 7 5.1 RF EXPOSURE TEST ................................................................................................................................................ 7 5.1.1 E.U.T. Operation ........................................................................................................................................ 7 6 PHOTOGRAPHS- RF EXPOSURE SETUP ...................................................................................................... 23 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191001977002 Page: 4 of 23 3 General Information 3.1 Details of E.U.T. Power Supply: Car charger： Input:DC 12V-24V Output:DC 5V2.4A Output QC 3.0:DC 5V3A,9V2A,12V1.5A Wireless Charger Mat： Input:DC 5V/2A,9V/1.67A Output:10W Max Cable: USB cable:100cm unshielded Antenna Type: Loop Antenna Antenna Gain: 0dBi Modulation Type: Load Modulation Operation Frequency: 111.058kHz to 140.545kHz Remark: This device has been tested the worst status of full load and the device has been tested with load at 5W,7.5W and 10W,the worst case 10W is reported only.The EUT has two coils,but the two coils cannot work at the same time. 3.2 Description of Support Units Description Manufacturer Model No. Serial No. iPhone 8 Apple A1863 F4GVQ656JC6D Rechargeable Battery Gadlee DP00027 REF. No.SEA2800 SAMSUNG Galaxy S8 SAMSUNG SM-G9500 R28J9140LPB SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191001977002 Page: 5 of 23 3.3 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen Branch E&E Lab, No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong,China 518057. Tel: +86 755 2601 2053 Fax: +86 755 2671 0594 No tests were sub-contracted. 3.4 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Innovation, Science and Economic Develop…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191001977001 Page: 1 of 25 Keny Xu EMC Laboratory Manager TEST REPORT Application No.: SZEM1910019770CR Applicant: HANK ELECTRONICS CO., LTD. Address of Applicant: Floor 2nd-7th, A8, Hongye Industry City Lezhujiao, Zhoushi Road, Baoan District, Shenzhen, China Manufacturer: HANK Electronics Co., Ltd. Address of Manufacturer: Floor 2nd-7th, A8, Hongye Industry City, Lezhujiao, Zhoushi Road, Baoan District, Shenzhen, China Factory: HANK Electronics Co., Ltd. Address of Factory: Floor 2nd-7th, A8, Hongye Industry City, Lezhujiao, Zhoushi Road, Baoan District, Shenzhen, China Equipment Under Test (EUT): EUT Name: Wireless Charger Mat Model No.: HKWP1661-10E FCC ID: 2AIOC-1661 Standard(s) : 47 CFR Part 15, Subpart C Date of Receipt: 2019-10-31 Date of Test: 2019-11-11 to 2019-11-14 Date of Issue: 2019-11-19 Test Result: Pass* * In the configuration tested, the EUT complied with the standards specified above. SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191001977001 Page: 2 of 25 Revision Record Version Chapter Date Modifier Remark 01 2019-11-19 Original Authorized for issue by: Bill Chen /Project Engineer Eric Fu /Reviewer SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191001977001 Page: 3 of 25 2 Test Summary Radio Spectrum Technical Requirement Item Standard Method Requirement Result Antenna Requirement 47 CFR Part 15, Subpart C N/A 47 CFR Part 15, Subpart C 15.203 Pass Radio Spectrum Matter Part Item Standard Method Requirement Result 20dB Bandwidth 47 CFR Part 15, Subpart C ANSI C63.10 (2013) Section 6.9.2 47 CFR Part 15, Subpart C 15.215 Pass Restricted Bands 47 CFR Part 15, Subpart C ANSI C63.10 (2013) Section 6.10.5 47 CFR Part 15, Subpart C 15.205 Pass Radiated Emissions (9kHz-30MHz) 47 CFR Part 15, Subpart C ANSI C63.10 (2013) Section 6.4 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass Radiated Emissions (30MHz-1GHz) 47 CFR Part 15, Subpart C ANSI C63.10 (2013) Section 6.5 47 CFR Part 15, Subpart C 15.205 & 15.209 Pass SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM191001977001 Page: 4 of 25 3 Contents Page 1 COVER PAGE ............................................................................................................................................ 1 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 4 4 GENERAL INFORMATION ........................................................................................................................ 5 4.1 DETAILS OF E.U.T. ............................................................................................................................... 5 4.2 DESCRIPTION OF SUPPORT UNITS ......................................................................................................... 5 4.3 MEASUREMENT UNCERTAINTY .............................................................................................................. 5 4.4 TEST LOCATION .................................................................................................................................... 6 4.5 TEST FACILITY ...................................................................................................................................... 6 4.6 DEVIATION FROM STANDARDS ............................................................................................................... 6 4.7 ABNORMALITIES FROM STANDARD CONDITIONS ..................................................................................... 6 5 EQUIPMENT LIST ...................................................................................................................................... 7 6 RADIO SPECTRUM TECHNICAL REQUIREMENT ............................................................................... 10 6.1 ANTENNA REQUIREMENT .................................................................................................................... 10 6.1.1 Test Requirement: ....................................................................................................................... 10 6.1.2 Conclusion ................................................................................................................................... 10 7 RADIO SPECTRUM MATTER TEST RESULTS ..................................................................................... 11 7.1 20DB BANDWIDTH .............................................................................................................................. 11 7.1.1 E.U.T. Operation .......................................................................................................................... 11 7.1.2 Test Setup Diagram ..................................................................................................................... 11 7.1.3 Measurement Procedure and Data............................................................................................. 11 7.2 RESTRICTED BANDS ........................................................................................................................... 13 7.2.1 E.U.T. Operation .......................................................................................................................... 13 7.2.2 Test Setup Diagram ..................................................................................................................... 13 7.2.3 Measurement Procedure and Data............................................................................................. 14 7.3 RADIATED EMISSIONS (9KHZ-30MHZ) ................................................................................................. 15 7.3.1 E.U.…

Text truncated - open the document above for the full version.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 2 Setup Photos for SZEM1910019770CR FCC ID: 2AIOC-1661 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 2 1 Photographs 1.1 Radiated Emissions (9kHz-30MHz) Test Setup 1.2 Radiated Emissions (30MHz-1GHz) Test Setup

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 1 of 7 RF Exposure Setup Photos for SZEM1910019770CR FCC ID: 2AIOC-1661 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 2 of 7 1 Photographs 0-2-4-6-8-10-15cm SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 3 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 4 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 5 of 7 0cm SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 6 of 7 SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Page: 7 of 7