2AJGM-AR1909UAmateur Radio

PREFACE Thank you for purchasing our Amateur Radio. This easy-to-use radio will deliver you secure, instant and reliable communications at peak efficiency. Please read this manual carefully before use. The information presented here, it will help you to derive maximum performance from your radio. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBIITED UNDER FCC RULES AND FEDERRAL LAW. ATTENTION! When programming the radio, start by reading the factory software data, and then rewrite this data with your frequency etc., to a new saved code plug, otherwise errors may occur. You can use the programming cable with a PC to program the authorized frequency, bandwidth, power, etc. your programming must comply with your FCC (or EU other country) license certification. ATTENTION! Before using this product, read the RF Energy Exposure and Product Safety Guide that ship with the radio which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation. Table of Contents 1. GETTING STARTED 1.1 Regulations and Safety Warnings 1.2 Maintenance 1.3 Content of the packaging 1.4 Main features 2. BATTERY RECHARGE 2.1 Charging the Battery Pack 2.2 Charger Supplied 2.3 Use Caution with the Li-ion Battery 2.4 How to Charge 2.5 LED Indicator 3. INSTALLATION OF ACCESSORIES 3.1 Installing the belt clip 3.2 Installing the battery pack 3.3 Additional Speaker/Microphone (Optional) 4. RADIO OVERVIEW 5. BASIC OPERATIONS 5.1 Power on/off and volume adjustment 5.2 Transmission 5.3 Monitor 5.4 VOX 5.5 FM Radio (FM) 5.6 Prompt voice switch settings 5.7 English/Chinese language switch 5.8 Squelch 5.9 CTCSS/DCS tones 5.10 Scan 6. ON-LINE SERVICE AND SUPPORT 1. GETTING STARTED 1.1 Regulations and Safety Warnings ■FCC Regulatory Conformance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the the following two conditions: (1) This device may not cause harmful interference, and ■EU Regulatory Conformance (2) this device must accept any interference received, including interference that may cause undesired operation. As certified by the qualified laboratory, the product is in compliance with the essential requirements and other relevant 2012/19/EU). NOTE: It can be operating under 2000m. Please note that the above information is applicable to EU countries only. ■Compliance with RF Exposure Standards The radio complies with the following RF energy exposure standards and guidelines: • United States Federal Communications Commission, Code of Federal Regulations; 47 CFR § 1.1307, 1.1310 and 2.1093 • American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005; Canada RSS102 Issue 5 March 2015 • Institute of Electrical and Electronic Engineers (IEEE) C95.1:2005 Edition RF Exposure Compliance and Control Guidelines and Operating Instructions To control your exposure and ensure compliance with the occupational/ controlled environmental exposure limits, always adhere to the following procedures. Guidelines: • Do not remove the RF Exposure Label from the device. • User awareness instructions should accompany device when transferred to other users. • Do not use this device if the operational requirements described herein are not met. Operating Instructions: • Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the [PTT] key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance). provisions of the Directive 2014/53/EU. All applicable EU regulations are regarded (2006/66/EC, 2011/65/EU,(EU)2015/863, • Keep the radio unit at least 2.5cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes. • When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC's occupational/ controlled environmental RF exposure limits. • Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines. • Contact your local dealer for the product's optional accessories. ■Precautions for Portable Terminals Operating Prohibitions To protect you against any property loss, bodily injury or even death, be sure to observe the following safety instructions: 1. Do not operate the product in a location containing fuels, chemicals, explosive atmospheres and…

Text truncated - open the document above for the full version.

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY ADD:3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] 202 3-06-14 FEDERAL COMMUNICATIONS COMMISSIONS Autho rization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Declaration of compliance to the requirements of §15.121 FCC ID:2AJG M-AR1909U We declare that, this scanning receiver is incapable of operating (tuning), or readily being altered by the users to operate, within the frequency bands allocated to the Cellular Radiotelephone Service in part 22 of this chapter (cellular telephone bands). This device will not be able to receive transmissions in the cellular telephone bands by means of clipping the leads of, or installing, a simple component such as a diode, resistor or jumper wire; replacing a plug-in semicon ductor chip; or programming a semiconductor chip using special access codes or an external device, such as a personal computer. This device is also incapable of converting digital cellular communication transmissions to analog voice audio. This device is designed so that the tuning, control and filtering circuitry is inaccessible. Any attempts to modify the equipment to receive transmissions from the Cellular Radiotelephone Service will render the receiver in operable. This scan ning receiver rejects any signals from the Cellular Radiotelephone Service frequency bands that are 38 dB or lower based upon a 12 dB SINAD measurement. We are aware that the modification of this device to receive transmissions from Cellular Radiotelephone Service frequency bands will be considered to constitute manufacture of such equipment. This includes any individual, individuals, entity or organization that modifies one or more scanners. Any modification to receive transmissions from the Cellular Radiotelephone Service frequency bands voids the certification of the scanning receiver, regardless of the date of manufacture of the original unit. Sincerely, Signature: Typed or Printed Name: Title: Manager Peter Wang

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] Attestation Letter Date: 2023-06-14 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements for Amateur TX Frequencies FCC ID: 2AJGM-AR1909U PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the applicant”) certifies that the equipment for transmitter frequencies can be programmed for only amateur frequencies (channels). Sincerely, Signature Printed Name: Peter Wang Title: Manager

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED CFR 47 §2.911(d)(5)(i)(ii) Attestation Letter Attestation Letter Date: 06-14-2023 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i)(ii) Filing FCC ID: 2AJGM-AR1909U PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the applicant”) certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature Contact Person: Peter Wang Title: Manager Company Name: PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Address: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong

QA-FR-170-B PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] FCC Authorization Date: 2023-06-14 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED, Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s signature Printed Name: Peter Wang Title: Manager

QA-FR-171-A PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] FCC Confidential Authorization Date: 2023-06-14 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AJGM- AR1909U In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Printed Name: Peter Wang Title: Manager  Internal Photo

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] DECLARATION OF SIMILARITY Date: 2023-06-14 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: We, PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED, hereby declare that the product: Amateur Radio, FCC ID: 2AJGM- AR1909U. model: AT-1909B is electrically identical with the model: AR-1909U which was tested by China Certification ICT Co., Ltd (Dongguan) with the same electromagnetic emissions and electromagnetic compatibility characteristics. A description of the differences between those models and that are declared similar are as follows: They are the same product, just different model name, the rest are the same. Please contact me should there be need for any additional clarification or information. Best Regards, Signature: Printed Name: Peter Wang Title: Manager

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS Antenna

TEST REPORT Applicant: PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Address: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong FCC ID: 2AJGM-AR1909U Product Name: Amateur Radio Standard(s): 47 CFR Part 15 Subpart B ANSI C63.4-2014 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR230311938-00A Date Of Issue: 2023/6/30 Reviewed By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230311938-00A Page 2 of 46 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR230311938-00A Page 3 of 46 CONTENTS TEST FACILITY ............................................................................................................................................................ 2 DECLARATIONS ........................................................................................................................................................... 2 DOCUMENT REVISION HISTORY ......................................................................................................................... 4 1. GENERAL INFORMATION .................................................................................................................................. 5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 5 1.2 DESCRIPTION OF TEST CONFIGURATION ................................................................................................................ 6 1.2.2 Support Equipment List and Details.............................................................................................................. 6 1.2.3 Support Cable List and Details ...................................................................................................................... 6 1.2.4 Block Diagram of Test Setup ........................................................................................................................ 7 1.3 MEASUREMENT UNCERTAINTY ............................................................................................................................. 9 2. SUMMARY OF TEST RESULTS ........................................................................................................................ 10 3. REQUIREMENTS AND TEST PROCEDURES ................................................................................................. 11 3.1 AC LINE CONDUCTED EMISSIONS ....................................................................................................................... 11 3.1.1 EUT Setup ................................................................................................................................................... 11 3.1.2 EMI Test Receiver Setup ............................................................................................................................ 11 3.1.3 Test Procedure ............................................................................................................................................. 12 3.1.4 Corrected Amplitude & Margin Calculation ............................................................................................... 12 3.2 RADIATION SPURIOUS EMISSIONS ....................................................................................................................... 13 3.2.1 EUT Setup ................................................................................................................................................... 13 3.2.2 Equipment Setup ......................................................................................................................................... 14 3.2.3 Test Procedure ............................................................................................................................................. 14 3.2.4 Corrected Amplitude & Margin Calculation ............................................................................................... 14 3.3 ANTENNA POWER CONDUCTION LIMITS FOR RECEIVERS .................................................................................... 15 3.3.1 Applicable Standard .................................................................................................................................... 15 3.3.2 Block Diagram of Test Setup ..............................................…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions Front View-M2 Conducted Emissions Side View-M2 Conducted Emissions Front View-M1 Conducted Emissions Side View-M1 Radiated Emission Below 1GHz Front View-M2 Radiated Emission Below 1GHz Rear View- M2 Radiated Emission Below 1GHz Front View-M1 Radiated Emission Below 1GHz Rear View-M1 Radiated Emission Above 1GHz Front View-M2 Radiated Emission Above 1GHz Rear View-M2 Radiated Emission Above 1GHz Front View-M1 Radiated Emission Above 1GHz Rear View-M1