2AJGM-BF88AFRS TWO WAY RADIO

User Manual（FCC&IC） Draft Model: BF-88A ATTENTION Your BF-88A is a multi-task FRS transceiver. Combining the latest technology in radio communication along with a sturdy mechanical frame, BF-88A is the ideal and effective solution for the professionals who need to stay in touch with the working team (in construction sites, buildings, shows, trade fairs or hotels) or for leisure users that just want to keep up with friends and family. To help you ward off bodily injury or property loss that may arise from improper operation, please read all the information carefully before using our products. Intended Use Our products are designed to provide reliable wireless communication services for users across many industry sectors. In order to use the products safely and to achieve the best performance, they must be used as intended. The operator of the product is responsible for damage to the product or damage caused by the product if the product was used beyond the intended use instructions. Intended use includes that: • The product is used by users who have full knowledge of its RF exposure and can exercise control over their RF exposure to meet the occupational limits in FCC/ICNIRP and international standards. • All the security instructions set forth in this document are always heeded. • The general, national and in-house safety regulations are heeded. • The product is exclusively used with the frequencies licensed by the respective authority. • The product is configured appropriately by the dealer. Besides, intended use also requires the product operator to be well-trained and to be familiar with the applicable standards, regulations and provisions. REGULATORY Information Important: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. Your radio is set up to transmit a regulated signal on an assigned frequency. It is against the law to alter or adjust the settings inside the radio to exceed those limitations. Any adjustments to your radio must be made by qualified technicians. To be safe and sure: • Never open your radio’s case. • Never change or replace anything in your radio except the battery. • Any attempt to change frequencies or output power of the radio invalidates the approval Your radio might cause TV or radio interference even when it is operating properly. To determine whether Your radio is causing the interference, turn it off. If the interference goes away, your radio is causing it. Try to eliminate the interference by moving your radio away from the receiver. If you cannot eliminate the interference, the FCC requires that you stop using the radio. Hazardous Environments: Do not operate the radio in hazardous environments. Explosion or fire may result. Do not operate the radio near unshielded electrical blasting caps. Under certain conditions, radios can interfere with blasting operations and may cause an explosion. Turn your radio OFF to prevent accidental transmission when in a blasting area or in areas posted: "Turn off two-way radio." Construction crews often use remote control RF devices to set off explosives. Note: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited. RF EXPOSURE INFORMATION WARNING! Read this information before using the radio. In August 1996 the Federal Communications Commission (FCC) of the United States with its action in Report and Order FCC 96-326 adopted an updated safety standard for human Exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters.Those guidelines are consistent with the safety standard previously set by both U.S. and International standards bodies. The design of the radio complies with the FCC guidelines and these international standards.Never allow children to operate the radio without adult supervision and the knowledge of the following guidelines. WARNING! It is up to the user to properly operate this radio transmitter to insure safe operation. Please adhere to the User Manual（FCC&IC） Draft Model: BF-88A following: Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or Attachments could impair call quality, damage the radio, or result in violation of FCC regulations. Do not use the radio with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for a replacement antenna. Any attempt to change frequencies or output power of the radio invalidates the approval. ■ FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Our radio generators RF electromagnetic energy during transmit mode. This radio is designed for and classified as " General Population”,meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways To Minimize Such hazards. This radio is NOT intended for use by the” Occupational Use Only” in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for“General Population”. In addition, our radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: ---IEEE Std. 1528:2013 and KDB447498, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. ---American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. ---American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields-RF and Microwave. The information listed above provides the user with the information needed to …

Text truncated - open the document above for the full version.

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Agent Authorization Company: PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Address: 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Product Name: TWO WAY RADIO Model Number(s): BF-88A, BF-888S, BF-666S, BF-777S, GT-1, BF-888Splus, BF- 888SA, F8S, BF-888H Product Description: FRS TWO WAY RADIO We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: Jan. 14, 2021 Name: Peter Wang Title: General Manager Company: PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Jan. 14, 2021 To: Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation statement regarding the Mobile Radio frequency Applicant: PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong TYPE OF QEUIPMENT: Family Radio Face Held Transmitter FCC ID: 2AJGM-BF88A Dear Sir or Madam I attest that the product has one antenna, one battery capacity, one body-worn and audio accessory. And that the product could program the frequency on computer through interface by manufacturer, is incapable of tuning, or readily being altered, by the end-user. Please contact the undersigned if you have any questions or need any further information. Regards Signature: Name, Job Title and Dept.: Peter Wang / General Manager

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: Jan. 14, 2021 Subject; Request for Confidentiality FCC ID: 2AJGM-BF88A To Whom It May Concern, Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. Schematic Diagram Block Diagram Parts List Operational Description Tune-up Procedure It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Peter Wang Title: General Manager

PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Jan. 14, 2021 Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Subject: Explanation of differences between product types FCC ID: 2AJGM-BF88A Models: BF-88A, BF-888S, BF-666S, BF-777S, GT-1, BF-888Splus, BF-888SA, F8S, BF-888H To Whom It May Concern: We, The PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY hereby declare that the model : BF-888S, BF-666S, BF-777S, GT-1, BF-888Splus, BF-888SA, F8S, BF-888H is identical with the model : BF-88A, except the model name. Except for the different above, no other modification is performed. Sincerely, PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Signature: [Peter Wang, General Manager]

External Photos WHOLE VIEW OF EUT TOP VIEW OF EUT BOTTOM VIEW OF EUT FRONT VIEW OF EUT BACK VIEW OF EUT LEFT VIEW OF EUT RIGHT VIEW OF EUT

FCC ID Label Location 15mm*10mm FCC ID: 2AJGM-P51UV

Internal Photos OPEN VIEW-1 OF EUT OPEN VIEW-2 OF EUT OPEN VIEW-3 OF EUT INTERNAL VIEW-1 OF EUT Antenna INTERNAL VIEW-2 OF EUT INTERNAL VIEW-3 OF EUT INTERNAL VIEW-4 OF EUT INTERNAL VIEW-5 OF EUT INTERNAL VIEW-6 OF EUT

Page: 1 of 28 TEST REPORT Report No. ...................................... : CHTEW21010031 Report verificaiton: Project No. ...................................... : SHT2101000402EW FCC ID ............................................. : 2AJGM -BF88A Applicant’s name ........................... : PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Address ............................................. : 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Test item description .................... : TWO WAY RADIO Trade Mark ....................................... : POFUNG,BAOFENG Model/Type reference ....................... : BF-88A Listed Model(s) ................................. : BF-888S,BF-666S,BF-777S,GT-1,BF-888Splus,BF-888SA， F8S, BF-888H Standard ......................................... : FCC 47 CFR Part2.1093 IEEE Std C95.1, 1999 Edition IEEE 1528: 2013 Date of receipt of test sample.........: Jan.04, 2021 Date of testing.............................: Jan.05, 2021- Jan.11, 2021 Date of issue...............................: Jan.12, 2021 Result .................. ........................: PASS Compiled by ( position+printed name+signature) .. : File administrators: Fanghui Zhu Supervised by ( position+printed name+signature) .. : Test Engineer: Patrick Qiu Approved by ( position+printed name+signature) .. : Manager: Hans Hu Testing Laboratory Name ............. : Shenzhen Huatongwei International Inspection Co., Ltd Address ............................................. : 1/F, Bldg 3, Hongfa Hi-tech Industrial Park, Genyu Road, Tianliao, Gongming, Shenzhen, China Shenzhen Huatongwei International Inspection Co., Ltd. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the Shenzhen Huatongwei International Inspection Co., Ltd is acknowledged as copyright owner and source of the material. Shenzhen Huatongwei International Inspection Co., Ltd takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. The test report merely correspond to the test sample. Report No.: CHTEW21010031 Page: 2 of 28 Issued: 2021-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V03 (2021-01) Contents 1. Statement of Compliance 3 2. Test Standards and Report version 4 2.1. Test Standards 4 2.2. Report version 4 3. Summary 5 3.1. Client Information 5 3.2. Product Description 5 3.3. Radio Specification Description 5 3.4. Test frequency list 6 3.5. Testing Laboratory Information 7 3.6. Environmental conditions 7 4. Equipments Used during the Test 8 5. Measurement Uncertainty 9 6. SAR Measurements System Configuration 10 6.1. SAR Measurement Set-up 10 6.2. DASY5 E-field Probe System 11 6.3. Phantoms 12 6.4. Device Holder 12 7. SAR Test Procedure 13 7.1. Scanning Procedure 13 7.2. Data Storage and Evaluation 15 8. Position of the wireless device in relation to the phantom 17 8.1. Front-of-face 17 8.2. Body Position 17 9. Dielectric Property Measurements & System Check 18 9.1. Tissue Dielectric Parameters 18 9.2. SAR System Validation 19 9.3. System Check 20 10. SAR Exposure Limits 23 11. Radiated Power Measurement Results 23 12. Maximum Tune-up Limit 23 13. SAR Measurement Results 24 14. Test Setup Photos 25 15. External Photos of the EUT 26 Report No.: CHTEW21010031 Page: 3 of 28 Issued: 2021-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V03 (2021-01) 1. Statement of Compliance Maximum Reported SAR (W/kg @1g) RF Exposure Conditions FRF Front of face(Dist.= 25mm) 0.525 Body-worn(Dist.= 0mm) 1.082 This device is in compliance with Specific Absorption Rate (SAR) for general population/uncontrolled exposure limits (1.6 W/kg) specified in FCC 47 CFR part 2 (2.1093) and ANSI/IEEE C95.1-1992, and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528-2013 and FCC KDB publications. Report No.: CHTEW21010031 Page: 4 of 28 Issued: 2021-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V03 (2021-01) 2. Test Standards and Report version 2.1. Test Standards The tests were performed according to following standards: FCC 47 Part 2.1093: Radiofrequency Radiation Exposure Evaluation:Portable Devices IEEE Std C95.1, 1999 Edition: IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz IEEE Std 1528™-2013: IEEE Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques. FCC published RF exposure KDB procedures: KDB 865664 D01 SAR Measurement 100 MHz to 6 GHz v01r04: SAR Measurement Requirements for 100 MHz to 6 GHz KDB 865664 D02 RF Exposure Reporting v01r02: RF Exposure Compliance Reporting and Documentation Considerations KDB 447498 D01 General RF Exposure Guidance v06: Mobile and Portable Device RF Exposure Procedures and Equipment Authorization Policies TCB workshop: April, 2019; Page 19, Tissue Simulating Liquids (TSL) 2.2. Report version Revision No. Date of issue Description N/A 2021-01-12 Original Report No.: CHTEW21010031 Page: 5 of 28 Issued: 2021-01-12 Shenzhen Huatongwei International Inspection Co., Ltd. Report Template Version: V03 (2021-01) 3. Summary 3.1. Client Information Applicant: PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Address: 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Manufacturer: PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Address: 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Factory: PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Address: 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong 3.2. Product Description Main unit Name of EUT: TWO WAY RADIO Trade mark: POFUNG,BAOFENG Model/Type reference: BF-88A Listed model(s): BF-888S,BF-666S,BF-777S,GT-…

Text truncated - open the document above for the full version.

Appendix B: DAE and Probe Calibration Certificate 1 of 12 1.1. DAE4 Calibration Certificate Appendix B: DAE and Probe Calibration Certificate 2 of 12 Appendix B: DAE and Probe Calibration Certificate 3 of 12 Appendix B: DAE and Probe Calibration Certificate 4 of 12 1.2. Probe Calibration Certificate-3842 Appendix B: DAE and Probe Calibration Certificate 5 of 12 Appendix B: DAE and Probe Calibration Certificate 6 of 12 Appendix B: DAE and Probe Calibration Certificate 7 of 12 Appendix B: DAE and Probe Calibration Certificate 8 of 12 Appendix B: DAE and Probe Calibration Certificate 9 of 12 Appendix B: DAE and Probe Calibration Certificate 10 of 12 Appendix B: DAE and Probe Calibration Certificate 11 of 12 Appendix B: DAE and Probe Calibration Certificate 12 of 12 Appendix C: Dipole Calibration Certificate 1 of 9 1.1. D450V3 Dipole Calibration Certificate Appendix C: Dipole Calibration Certificate 2 of 9 Appendix C: Dipole Calibration Certificate 3 of 9 Appendix C: Dipole Calibration Certificate 4 of 9 Appendix C: Dipole Calibration Certificate 5 of 9 Appendix C: Dipole Calibration Certificate 6 of 9 Appendix C: Dipole Calibration Certificate 7 of 9 Appendix C: Dipole Calibration Certificate 8 of 9 Appendix C: Dipole Calibration Certificate 9 of 9 Extended Dipole Calibrations Referring to KDB865664 D01, if dipoles are verified in return loss (<-20dB, within 20% of prior calibration), and in impedance (within 5 ohm of prior calibration), the annual calibration is not necessary and the calibration interval can be extended. Head Date of measurement Return-loss (dB) Delta (%) Real Impedance (ohm) Delta (ohm) Imaginary impedance (ohm) Delta (ohm) 2018-02-23 -21.1 59.6 -0.2 2019-02-15 -21.8 -3.32 59.1 0.5 -0.8 0.6 2020-01-22 -21.8 -3.32 58.8 0.8 -0.5 0.3 The return loss is <-20dB, within 20% of prior calibration; the impedance is within 5ohm of prior calibration. Therefore the verification result should support extended calibration.

Page 1 of 47 FCC Test Report Report No.:AGC02294200803FE10 FCC ID : 2AJGM-BF88A PRODUCT DESIGNATION : TWO WAY RADIO BRAND NAME : POFUNG, BAOFENG MODEL NAME : BF-88A, BF-888S, BF-666S, BF-777S, GT-1, BF-888Splus, BF-888SA, F8S, BF-888H APPLICANT : PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY DATE OF ISSUE : Dec. 11, 2020 STANDARD(S) : FCC Part 95 Rules REPORT VERSION : V 1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd Report No.: AGC02294200803FE10 Page 2 of 47 Report Revise Record Report Version Revise Time Issued Date Valid Version Notes V1.0 / Dec. 11, 2020 Valid Initial release Report No.: AGC02294200803FE10 Page 3 of 47 VERIFICATION OF COMPLIANCE Applicant PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Address 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong manufacturer PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Address 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Factory PO FUNG ELECTRONIC(HK) INTERNATIOANL GROUP COMPANY Address 3/F FULOK BLDG 131-133 WING LOK ST SHEUNG WAN, Hong Kong Product Designation: TWO WAY RADIO Brand Name: POFUNG,BAOFENG Test Model BF-88A Series Model BF-888S, BF-666S, BF-777S, GT-1, BF-888Splus, BF-888SA, F8S, BF-888H Difference Description All the same except the model name. Deviation No any deviation from the test method Condition of Test Sample Normal Date of Test: Nov. 01, 2020~Dec. 11, 2020 Test Result PASS Report Template AGCRT-US-PTT/RF WE HEREBY CERTIFY THAT: The above equipment was tested by Attestation of Global Compliance (Shenzhen) Co., Ltd. The data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in TIA/EIA 603. The sample tested as described in this report is in compliance with the FCC Rules Part 95 requirements. The test results of this report relate only to the tested sample identified in this report. Prepared By Donjon Huang (Project Engineer) Dec. 11, 2020 Reviewed By Calvin Liu (Reviewer) Dec. 11, 2020 Approved By Forrest Lei Authorized Officer Dec. 11, 2020 Report No.: AGC02294200803FE10 Page 4 of 47 TABLE OF CONTENTS 1. GENERAL INFORMATION ............................................................................................................................. 6 1.1 PRODUCT DESCRIPTION ......................................................................................................................... 6 1.2 RELATED SUBMITTAL(S)/GRANT(S) ....................................................................................................... 8 1.3 TEST METHODOLOGY .............................................................................................................................. 8 1.4 ADDRESS OF THE TEST LABORATORY .................................................................................................. 8 1.5 TEST FACILITY ........................................................................................................................................... 8 1.6 SPECIAL ACCESSORIES ........................................................................................................................... 9 1.7 EQUIPMENT MODIFICATIONS .................................................................................................................. 9 1.8 ANTENNA REQUIREMENT ........................................................................................................................ 9 2. SYSTEM TEST CONFIGURATION ................................................................................................................ 10 2.1 EUT CONFIGURATION ........................................................................................................................... 10 2.2 EUT EXERCISE ........................................................................................................................................ 10 2.3 CONFIGURATION OF TESTED SYSTEM .............................................................................................. 10 2.4 MEASUREMENT UNCERTAINTY ............................................................................................................ 11 3. SUMMARY OF TEST RESULTS .................................................................................................................... 12 4. DESCRIPTION OF TEST MODES ................................................................................................................. 14 5. FREQUENCY TOLERANCE .......................................................................................................................... 15 5.1 PROVISIONS APPLICABLE ..................................................................................................................... 15 5.2 MEASUREMENT PROCEDURE .............................................................................................................. 15 5.3 TEST SETUP BLOCK DIAGRAM ............................................................................................................. 16 5.3 TEST RESULT ......................................................................................................................................... 17 6. EMISSION BANDWIDTH ............................................................................................................................... 18 6.1 PROVISIONS APPLICABLE ..................................................................................................................... 18 6.2 MEASUREMENT PROCEDURE .............................................................................................................. 18 6.3 TEST SETUP BLOCK DIAGRAM ............................................................................................................. 18 6.4 MEASUREMENT RESULT ........................................................................................................................ 20 7. UNWANTED RADIATION ......................................…

Text truncated - open the document above for the full version.

Test Setup Photos RADIATED EMISSION BELOW 1G TEST SETUP RADIATED EMISSION ABOVE 1G TEST SETUP

Test Setup Photos Front-of-face(25mm) Body-worn(0mm)