2AJGM-GMT8GMRS Two Way Radio

FRS TWO WAY RADIO OWNER’S MANUAL ATTENTION! The radio is a multitask FRS transceiver. Combining the latest technology in radio communication along with a sturdy mechanical frame, the radio is the ideal and effective solution for the professionals who need to stay in touch with the working team (in construction sites, buildings, shows, trade fairs or hotels) or for leisure users that just want to keep up with friends and family. To help you ward off bodily injury or property loss that may arise from improper operation, please read all the information carefully before using our products. Before operating the radio, please read all safety and operating instructions. Save all instructions in a safe place for future reference. FCC Part 15.21 Warning Statement NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. Content of the packaging Note: The number of the above materials may be depending on the number of packages. Package Content 2 PACK 6 PACK Radio 2 6 Li-ion Battery 2 6 Belt Clip 2 6 Owner’s Manual 1 1 Radio Overview 1. Antenna 2. PTT (Push-To-Talk) Button 3. Channel UP Button 4. Channel Down/Monitor Button 5. Battery release latch 6. Type-C USB Charging Port 7. Power switch/ Volume control 8. LED: TX red light, RX green light 9. Speaker 10. Type-C charging LED 11. Accessory Port Main features • FRS transceiver • Output power: 29.86dBm/23.61dBm • 22 FRS channels • Channel monitor • Channel scan • 260 Privacy Codes (50 CTCSS Codes & 210 DCS codes) • Vocal tuning • Battery save • Battery low alert • TOT (Time out timer) • 2Pin Kenwood accessory jack • Micro USB connector for charging • Li-Ion 1500mAh battery pack • Up to 5 km range* • Battery Life: up to 18 hours (under typical use conditions) Note: *Range may vary depending on environmental and/or topographical conditions. Installation of Accessories 1. Installing the battery pack Before attaching or removing the battery make sure your radio is turned off by turning the power/volume knob all the way counter-clockwise. a. Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio. b. Once aligned with the guide-rails, slide the battery upward until you hear a click as the battery locks in place. Remove the battery pack To remove the battery, press the battery release above the battery pack, as you slide the battery downward. 2.Installing the Belt Clip To install the Belt Clip, slide the clip down into the slot on the back of the radio until the Belt Clip-latch clicks. To remove the Belt Clip, press the Lock-tab down, and then gently pull the belt clip up toward the top of the radio. 3.External Speaker/Microphone Jack Each radio can be used with an optional external speaker/microphone or headset, freeing your hands for other tasks. To use an optional speaker / microphone or headset: a. Open the rubber cap on the side of the radio. b. Insert the plug(s) into the SPK/MIC jacks. c. Place the ear bud into your ear, and adjust the Microphone into your desired position. 4.Using a Headset You can use a headset (#480_5R) for more private communications. To use a headset, lift the rubber cover from over the headset jack, and then plug in the headset. Important: Your radio is not submersible or waterproof when using a headset jack. When you remove the headset, be sure to fully press the jack cover into place to restore its waterproof capability. Charging the Battery 1.Charging the Battery (1) Connect the USB port of the attached USB charger to the USB output port, such as a power bank or mobile phone adapter. (2) Charge the battery for 6 hours. Note: • Use only the supplied batteries, charger, and AC adapter or approved accessories. • Charge time may vary depending on the battery life remaining. • The batteries must be installed for the unit to operate, even if the unit is also connected to external power. • If battery power is low, you cannot operate the radio even using external power. Allow the batteries to charge before using. *If you try to transmit while power is low, the radio will automatically turn off. Warning: Do not charge alkaline batteries. The radio will not be used for a long time, please take out and keep the battery properly. 2. Using the Type-C USB Charger The Type-C USB charger is a handy port that allows you to conveniently charge your Li-ion battery pack. 1. Make sure your radio is turned OFF. 2. Plug the Type-C USB cable into the Type-C USB charging port on your battery. The other end of the data line is connected to the output port of the power bank or the adapter of the mobile phone. 3. An empty battery will be fully charged in 4 hours. Note: • It is recommended to power OFF your radio while charging. However, if power is turned on while charging, you may not be able to transmit a message if the battery is completely empty. • For optimal battery life, remove the radio from the charger within 6 hours. Do not store the radio while connected to the charger. Operations Power on/off and volume adjustment Rotate the Power/Volume knob clockwise to turn the radio on. Rotate the control clockwise /counter-clockwise to adjust the volume level as you prefer. To turn the radio off, rotate the control counter-clockwise till hearing a mechanical “click”. Channel selection In standby mode, directly press the Channel Up (+)/ Down(-) key to step down or down to select the channel. When the voice prompt function is turned on, the corresponding channel is broadcast by voice. Transmission To communicate, all radios in your group must be set to the same channel. Briefly press the Channel Down (-) to enable the Monitor feature in order to make sure that the frequency is not busy, and then press the [PTT] key. Release the [PTT] key to receive. Only one user at a time can talk during radio communications. Therefor…

Text truncated - open the document above for the full version.

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED CFR 47 §2.911(d)(5)(i)(ii) Attestation Letter Attestation Letter Date: 06-14-2023 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i)(ii) Filing FCC ID: 2AJGM-FR31S PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the applicant”) certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature Contact Person: Peter Wang Title: Manager Company Name: PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Address: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong

QA-FR-170-B PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] FCC Authorization Date: 2023-06-14 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED, Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s signature Printed Name: Peter Wang Title: Manager

QA-FR-171-A PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] FCC Confidential Authorization Date: 2023-06-14 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AJGM-FR31S In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED hereby requests long-term confidential treatment of information accompanying this application as outlined below:  Block Diagram  Schematics  Operation Description  Bom  Tune Up Procedure The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Printed Name: Peter Wang Title: Manager

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] DECLARATION OF SIMILARITY Date: 2023-06-14 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: We, PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED, hereby declare that the product: FRS TWO WAY RADIO, FCC ID: 2AJGM- FR31S. model: FR-S31, FR-W31 is electrically identical with the model: FR-31S which was tested by China Certification ICT Co., Ltd (Dongguan) with the same electromagnetic emissions and electromagnetic compatibility characteristics. A description of the differences between those models and that are declared similar are as follows: They are the same product, just different model name, the rest are the same. Please contact me should there be need for any additional clarification or information. Best Regards, Signature: Printed Name: Peter Wang Title: Manager

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS EUT Port

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS Uncover Port Chip Chip Antenna

TEST REPORT Applicant: PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Address: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong FCC ID: 2AJGM-FR31S Product Name: FRS TWO WAY RADIO Model Number: FR-31S, FR-S31, FR-W31 Standard(s): 47 CFR Part 15 Subpart B ANSI C63.4-2014 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR230311926-00B Date Of Issue: 2023/4/26 Reviewed By: Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230311926-00B Page 2 of 27 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR230311926-00B Page 3 of 27 CONTENTS TEST FACILITY ............................................................................................................................................................. 2 DECLARATIONS ............................................................................................................................................................ 2 DOCUMENT REVISION HISTORY ......................................................................................................................... 4 1. GENERAL INFORMATION ................................................................................................................................... 5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ............................................................................... 5 1.2 DESCRIPTION OF TEST CONFIGURATION ................................................................................................................ 6 1.2.2 Support Equipment List and Details .............................................................................................................. 6 1.2.3 Support Cable List and Details ...................................................................................................................... 6 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 7 1.3 MEASUREMENT UNCERTAINTY .............................................................................................................................. 8 2. SUMMARY OF TEST RESULTS ........................................................................................................................... 9 3. REQUIREMENTS AND TEST PROCEDURES ................................................................................................. 10 3.1 AC LINE CONDUCTED EMISSIONS ........................................................................................................................ 10 3.1.1 EUT Setup.................................................................................................................................................... 10 3.1.2 EMI Test Receiver Setup ............................................................................................................................. 10 3.1.3 Test Procedure ............................................................................................................................................. 11 3.1.4 Corrected Amplitude & Margin Calculation ................................................................................................ 11 3.2 RADIATION SPURIOUS EMISSIONS ........................................................................................................................ 12 3.2.1 EUT Setup.................................................................................................................................................... 12 3.2.2 EMI Test Receiver Setup ............................................................................................................................. 13 3.2.3 Test Procedure ............................................................................................................................................. 13 3.2.4 Corrected Amplitude & Margin Calculation ................................................................................................ 13 4. TEST DATA AND RESULTS ................................................................................................................................ 14 4.1 AC LINE CONDUCTED EMISSIONS ........................................................................................................................ 14 4.2 RADIATION SPURI…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions Front View Conducted Emissions Side View Radiated Emission Below 1GHz Front View Radiated Emission Below 1GHz Rear View Radiated Emission Above 1GHz Front View Radiated Emission Above 1GHz Rear View