2AJGM-NA26GBAmateur Radio

202 4-08-28 FEDERAL COMMUNICATIONS COMMISSIONS Autho rization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Declaration of compliance to the requirements of §15.121 We declare that, this scanning receiver is incapable of operating (tuning), or readily being altered by the users to operate, within the frequency bands allocated to the Cellular Radiotelephone Service in part 22 of this chapter (cellular telephone bands). This device will not be able to receive transmissions in the cellular telephone bands by means of clipping the leads of, or installing, a simple component such as a diode, resistor or jumper wire; replacing a plug-in semicon ductor chip; or programming a semiconductor chip using special access codes or an external device, such as a personal computer. This device is also incapable of converting digital cellular communication transmissions to analog voice audio. This device is designed so that the tuning, control and filtering circuitry is inaccessible. Any attempts to modify the equipment to receive transmissions from the Cellular Radiotelephone Service will render the receiver in operable. This scan ning receiver rejects any signals from the Cellular Radiotelephone Service frequency bands that are 38 dB or lower based upon a 12 dB SINAD measurement. PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] FCC ID:2AJGM-NA26GB We are aware that the modification of this device to receive transmissions from Cellular Radiotelephone Service frequency bands will be considered to constitute manufacture of such equipment. This includes any individual, individuals, entity or organization that modifies one or more scanners. Any modification to receive transmissions from the Cellular Radiotelephone Service frequency bands voids the certification of the scanning receiver, regardless of the date of manufacture of the original unit. Sincerely, Signature: Typed or Printed Name: Title: Manager Peter Wang

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] Attestation Letter Date: 2024-08-28 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements for Amateur TX Frequencies FCC ID: 2AJGM-NA26GB PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the applicant”) certifies that the equipment for transmitter frequencies can be programmed for only amateur frequencies (144-148MHz, 420-450MHz) Also, equipment programming is the responsibility of Authorized Service Personnel, in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Sincerely, Signature Contact Person: Peter Wang Title: Manager

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] Attestation Letter Date: 2024-08-28 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD21046 Dear Sir or Madam: We, PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED t ype of Equipment: Amateur Radio, Model name:AR26, NA26GB, GBD26 FCC ID: 2AJGM-NA26GB The product, only support TX: 144-148MHz, 420-450MHz and BT(2402-2480 MHz), RX:108-136MHz,136-174MHz,220-260MHz,350-390MHz,400-520MHz for the purpose of marketing, other frequencies has been shielded by software, the end user has no capability to activate it. Best Regards, Sincerely Yours, Signature: Contact Person: Peter Wang Title: Manager

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] CFR 47 §2.911(d)(5)(i)(ii) Attestation Letter Attestation Letter Date: 2024-08-28 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(5)(i)(ii) Filing FCC ID: 2AJGM-NA26GB PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED (“the applicant”) certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Signature: Contact Person: Peter Wang Title: Manager

PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED ADD: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong TEL: 00852-90831684 FAX: 00852-90831684 E-mail: [email protected] DECLARATION OF SIMILARITY Date: 2024-08-28 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: We, PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED, hereby declare that the product: Amateur Radio, FCC ID: 2AJGM-NA26GB model:NA26GB,GBD26 are electrically identical with the model: AR26 which was tested by Bay Area Compliance Laboratories Corp. (Dongguan) with the same electromagnetic emissions and electromagnetic compatibility characteristics. A description of the differences between those models and that are declared similar are as follows: They are the same product, but due to different e-commerce sales channels, the models are different Please contact me should there be need for any additional clarification or information. Best Regards, Signature: Printed Name: Peter Wang Title: Manager

TEST REPORT Applicant: PO FUNG ELECTRONIC (HK) INTERNATONAL GROUP COMPANY LIMITED Address: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong Product Name: Amateur Radio FCC ID: 2AJGM-NA26GB Standard(s): FCC Part 15B ANSI C63.4-2014 Report Number: 2402V60428E-RF-00B Report Date: 2024/8/14 The above device has been tested and found compliant with the requirement of the relative standards by Bay Area Compliance Laboratories Corp. (Dongguan). Reviewed By: Gavin Xu Approved By: Ivan Cao Title: RF Engineer Title: EMC Manager Bay Area Compliance Laboratories Corp. (Dongguan) No.12, Pulong East 1 st Road, Tangxia Town, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Note: The information marked ▲ is provided by the applicant, the laboratory is not responsible for its authenticity and this information can affect the validity of the result in the test report. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with ★. Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: 2402V60428E-RF-00B Report Template Version: FCC-Part 15B-V1.2 Page 2 of 67 CONTENTS DOCUMENT REVISION HISTORY ......................................................................................................................... 3 1. GENERAL INFORMATION .................................................................................................................................. 4 1.1 GENERAL DESCRIPTION OF EQUIPMENT UNDER TEST ........................................................................................... 4 1.2 ACCESSORY INFORMATION .................................................................................................................................... 4 1.3 EQUIPMENT MODIFICATIONS ................................................................................................................................. 4 2. SUMMARY OF TEST RESULTS .......................................................................................................................... 5 3. DESCRIPTION OF TEST CONFIGURATION ................................................................................................... 6 3.1 OPERATION FREQUENCY AND TEST CHANNEL: ..................................................................................................... 6 3.2 DESCRIPTION OF TEST CONFIGURATION ................................................................................................................ 6 3.3 EUT EXERCISE SOFTWARE .................................................................................................................................... 6 3.4 SUPPORT EQUIPMENT LIST AND DETAILS .............................................................................................................. 6 3.5 SUPPORT CABLE LIST AND DETAILS ...................................................................................................................... 6 3.6 BLOCK DIAGRAM OF TEST SETUP .......................................................................................................................... 7 3.7 TEST FACILITY ...................................................................................................................................................... 8 3.8 MEASUREMENT UNCERTAINTY ............................................................................................................................. 8 4. REQUIREMENTS AND TEST RESULTS ............................................................................................................ 9 4.1 AC LINE CONDUCTED EMISSIONS ......................................................................................................................... 9 4.1.1 Applicable Standard ...................................................................................................................................... 9 4.1.2 EUT Setup ..................................................................................................................................................... 9 4.1.3 EMI Test Receiver Setup ............................................................................................................................ 10 4.1.4 Test Procedure ............................................................................................................................................. 10 4.1.5 Corrected Amplitude & Margin Calculation ............................................................................................... 10 4.1.6 Test Data and Result ................................................................................................................................... 11 4.2 RADIATION SPURIOUS EMISSIONS ....................................................................................................................... 16 4.2.1 Applicable Standard .................................................................................................................................... 16 4.2.2 Test System Setup ....................................................................................................................................... 16 4.2.3 EMI Test Receiver Setup ............................................................................................................................ 17 4.2.4 Test Procedure ............................................................................................................................................. 17 4.2.5 Corrected Result & Margin Calculation ...............................................…

Text truncated - open the document above for the full version.