2AK9F-38110SMART WATCH

Issue description Incorrect step count Abnormal waggling or vibration of device Wear the watch properly to avoid abnormal vibration Possible cause Walked less than 15 steps Solution Watch failed to sync data to the App Sliding or walking in slippers The connected phone's Bluetooth is off Turn on the connected phone's Bluetooth Restart the "Fastrack Reflex World" App Out of Bluetooth signal range Make sure your watch is in close proximity to the connected phone App is shut down or has crashed Walk with normal posture/ wear something other than slippers Walk more than 15 steps continuously No display Connect to charger to charge the watch Low battery • Bluetooth BLE5.3 • Full-screen touch • 1.43" Amoled 466*466 pixel • Bluetooth call • Daily Tracking: Active/ Steps / Calories • SpO2 Blood Oxygen monitoring • Breathing training • Sleep monitoring report • Call notification • Find your phone • Music control • Camera control • Automatic recognition of motion • Pressure test • Female physical health Product Name Product Model 38110 38110 Battery Capacity Working Temperature Storage Environment 300mAh 0 to 45 Temperature: -20 to 60 RelativeHumidity: ≤90%RH Bluetooth Name Frequency Range Bluetooth Transmitting Power FT_38110_XXXX 2402MHz-2480MHz BLE:-0.62 dBm B T:5.97dBm Charging DurationAbout 2 hours Waterproof RatingIP68 (1.5 meters) User Manual SMART WATCH • Matters needing attention The electronic equipment contained in the product, if improperly handled or disposed of, may damage the environment or cause harm: • Do not open the shell of the watch. • Do not replace the built-in battery by yourself. • Do not use corrosive cleaner to clean the product. • Do not charge when the product is wet. • If the product is not completely dry, do not charge. • Do not expose the product to extended periods of direct sunlight. • Do not use the product in a sauna or steam room. • Do not expose the product to extremely high or low temperatures. Regulatory Information Procedure This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. symptoms, please stop using the device and consult your doctor: - Epilepsy or sensitivity to light. - Poor blood circulation or excess bruising; heart disease or other diseases. - You are yaking any medicine that may make you sensitive to light. Warning: This Smart Watch FT_38110_XXXX is not a medical device. The Smart Watch FT_38110_XXXX and its related Apps can’ t be used to diagnose, treat, or prevent any disease or medical condition. Before performing any exercise, sleep, or nutritional changes, be sure to seek the advice of qualified medical professionals, otherwise serious injury or death may occur. This symbol means that according to local laws and regulations your product and or its battery shall be disposed of separately from household waste. When this product reaches its end of life, user has the choice to give his product to a competent recycling organization. Proper recycling of your product will protect human health and the environment. • Medical Disclaimer • Battery warning • Search the FCC ID number The built-in lithium battery of the product is forbidden to be disassembled, impacted, extruded or put into fire. The battery under the very low air pressure may result in explosion or flammable liquid or gas leakage. Avoid the battery in a high-temperature environment or being exposed to liquid or gas leakage. Avoid the battery in a high-temperature environment or being exposed to strong sunlight to avert explosion. Don't use the battery continuously in case of serious ballooning. The battery shall be handled pursuant to the local regulations and shall not be disposed as household garbage. Don't try to repair, remove or refit the battery. Explosion may happen if the battery is replaced by incorrect model. Don't compress or puncture the battery with hard object. The battery leakage, overheating or outbreak of a fire may occur if the battery is destroyed. 1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device won't cause any harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has beentested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. • FCC statement • If the screen or shell is damaged, do not use the product. • Do not put the product in the dishwasher, washing machine or dryer. • Do not expose the product to fire, the battery may explode. • While cha…

Text truncated - open the document above for the full version.

A TTESTATION STATEMENT Titan Company Limited ADD:Integrity, #193, Veerasandra,Electronics City P.O., Off Hosur Main Road,Bangalore, India TEL: +918067046489 FAX: +918067046262 E- mail: [email protected] Date: 2023-08-09 F EDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements Part 2.911(d)(5)(i), (ii)Filling FCC ID: 2AK9F-38110 T itan Company Limited. certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. And Titan Company Limited. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Sincerely, Printed Name: S omprabh Kumar Singh Title: Mr.

U.S. AGENT LETTER OF ATTESTATION Date: 2023-08-10 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: Attestation Statements CFR 47 §2.911(d)(7) Filing FCC ID: 2AK9F-38110 Titan Company Limited. certifies that, as of the date of the filing of the application, Iconsigh Inc. is our designated U.S. agent for service of process for the above referenced FCC ID. Titan Company Limited. accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Iconsigh Inc. accepts, as of the date of the filing of the application, the obligation of the designated U.S. agent for service of process for the above referenced FCC ID. Designated U.S. Agent Information: Name: Iconsigh Inc. Address: 2310 Homestead Road, Suite C1, Los Altos, CA 94024, USA FRN: 0033398652 Tel.: +1 (408) 320-9867 Email: [email protected] Signed by (printed name): Benjamin Kaur Signature: Titan Company Limited Address:Integrity, #193, Veerasandra,Electronics City P.O., Off Hosur Main Road, Bangaloe, India FRN: 0026283705 Tel: +918067046489 Email: [email protected] Signature: Printed Name: Somprabh Kumar Singh

Titan Company Limited ADD:Integrity, #193, Veerasandra,Electronics City P.O., Off Hosur Main Road,Bangalore, India TEL: +918067046489 FAX: +918067046262 E- mail: [email protected] FCC Authorization Date: 2023-08-09 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We , Titan Company Limited, Hereby authorizes China Certification ICT Co., Ltd (Dongguan) to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by China Certification ICT Co., Ltd (Dongguan) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Client’s signature Printed Name: Somprabh Kumar Singh Title: Mr. QA-FR-170-B

Titan Company Limited ADD: Integrity, #193, Veerasandra, Electronics City P.O., Off Hosur Main Road, B angalore, India T EL: + 918067046489 FAX: +918067046262 E- mail: S [email protected] FCC Co nfidential Authorization Date: 2023-08-09 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: 2AK9F-38110 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, (Titan Company Limited) hereby requests long-term confidential treatment of information accompanying this application as outlined below: •Block Diagram •Schematics •Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Signature: Printed Name: Somprabh Kumar Singh Title: Mr. QA-FR-171- A

Titan Company Limited ADD: Integrity, #193, Veerasandra,Electronics City P.O., Off Hosur Main Road,Bangalore, India TEL: +918067046489 FAX: +918067046262 E-mail: [email protected] DECL ARATION OF SIMILARITY Date: 2023-08-09 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: We, Titan Company Limited , hereby declare that the product:SMART WATCH FCC ID: 2AK9F-38110. model: 38111 is electrically identical with the model:38110 which was tested by China Certification ICT Co., Ltd (Dongguan) with the same electromagnetic emissions and electromagnetic compatibility characteristics. A description of the differences between those models and that are declared similar are as follows: They are the same product, but the model are different, and the rest are the same. Best Regards, Signature: Printed Name: Somprabh Kumar Singh Title: Mr.

EXHIBIT B - EUT EXTERNAL PHOTOGRAPHS Page 1 of 4 EUT Page 2 of 4 Page 3 of 4 Page 4 of 4

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS Page 1 of 7 Uncover Page 2 of 7 Page 3 of 7 Page 4 of 7 Chip Page 5 of 7 Chip Antenna Page 6 of 7 Battery Page 7 of 7

China Certification ICT Co., Ltd (Dongguan) Report No.: CR230744309-00B Page 58 of 58 5. RF EXPOSURE EVALUATION 5.1 Applicable Standard According to§15.247(i) and §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensure that the public is not exposed to radio frequency energy level in excess of the Commission’s guideline. According to KDB447498 D01 General RF Exposure Guidance v06: The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where • f(GHz) is the RF channel transmit frequency in GHz • Power and distance are rounded to the nearest mW and mm before calculation • The result is rounded to one decimal place for comparison • 3.0 and 7.5 are referred to as the numeric thresholds in the step 2 below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 5) in section 4.1 is applied to determine SAR test exclusion. 5.2 Measurement Result The max conducted power including tune-up tolerance is 6 dBm (3.68 mW). [(max. power of channel, mW)/(min. test separation distance, mm)][√f(GHz)] =3.98/5*(√2.480) = 1.3< 3.0 Result: Compliant. The stand-alone SAR evaluation is not necessary. ===== END OF REPORT =====

AntennaSampleConfirmation Designer： Shenzhen Kaipushen Communication Technology Co., Ltd Add ： 2 Floor, Yulong Office building,Longcheng Industrial Zone,440 Longguan Road,Longhua District, Shenzhen,China Customer Shenzhen Taiji Internet of Things Technology Co., Ltd Shenzhen Kaipushen Communication Technology Co., Ltd Project Name OY722023-06-20 Date Project NO.
Bluetooth wire 0.8*20mm Notes Customer Material No G0115010002 Frequency Range BT Designed By RF Engineer StructuralEngineer Checked By EngineeringManager Client’s Approval 1.
Overview of specifications This specification describes the condition of OY72 built-in wire antenna,Its frequency band is BT. 2.
Antenna appearance 3.
Electrical 3.1.
Antenna band BT (MHz) 2402MHz-2480MHz 3.2.
Matching circuit The test point is the bonding pad of antenna,as shown below. 1.BT
Matched antenna 。 ElementValue E11.2PF E20R E30.75PF RFModule E1E3 Antenna E2 3.3.
Return Loss BTVSWR+Return (MHz)(MHz)/(dB) 2400-2500 24002480 VSWR 2.1551.626 Returnloss -11.08-14.36 3.4
Antenna gain Channel03978 Gain-6.28dBi-4.08dBi-3.85dBi Gaindiagram Free space dBi MHz

TEST REPORT Applicant: Titan Company Limited Address: Integrity, #193, Veerasandra, Electronics City P.O., Off Hosur Main Road, Bangalore, India FCC ID: 2AK9F-38110 Product Name: SMART WATCH Standard(s): 47 CFR Part 15, Subpart C(15.247) ANSI C63.10-2013 KDB 558074 D01 15.247 Meas Guidance v05r02 The above equipment has been tested and found compliant with the requirement of the relative standards by China Certification ICT Co., Ltd (Dongguan) Report Number: CR230744309-00B Date Of Issue: 2023/8/14 Reviewed By: Calvin Chen Title: RF Engineer Approved By:Sun Zhong Title: Manager Test Laboratory: China Certification ICT Co., Ltd (Dongguan) No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China Tel: +86-769-82016888 China Certification ICT Co., Ltd (Dongguan) Report No.: CR230744309-00B Page 2 of 58 Test Facility The Test site used by China Certification ICT Co., Ltd (Dongguan) to collect test data is located on the No. 113, Pingkang Road, Dalang Town, Dongguan, Guangdong, China. The lab has been recognized as the FCC accredited lab under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 442868, the FCC Designation No. : CN1314. The lab has been recognized by Innovation, Science and Economic Development Canada to test to Canadian radio equipment requirements, the CAB identifier: CN0123. Declarations China Certification ICT Co., Ltd (Dongguan) is not responsible for the authenticity of any test data provided by the applicant. Data included from the applicant that may affect test results are marked with a triangle symbol “▲”. Customer model name, addresses, names, trademarks etc. are not considered data. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested. This report cannot be reproduced except in full, without prior written approval of the Company. This report is valid only with a valid digital signature. The digital signature may be available only under the Adobe software above version 7.0. This report may contain data that are not covered by the accreditation scope and shall be marked with an asterisk “★”. China Certification ICT Co., Ltd (Dongguan) Report No.: CR230744309-00B Page 3 of 58 CONTENTS T EST FACILITY .......................................................................................................................................... 2 DECLARATIONS .......................................................................................................................................... 2 DOCUMENT REVISION HISTORY .......................................................................................... 5 1. GENERAL INFORMATION .................................................................................................... 6 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................... 6 1.2 DESCRIPTION OF TEST CONFIGURATION ........................................................................................... 7 1.2.1 EUT Operation Condition: ............................................................................................................................. 7 1.2.2 Support Equipment List and Details .............................................................................................................. 7 1.2.3 Support Cable List and Details ...................................................................................................................... 7 1.2.4 Block Diagram of Test Setup ......................................................................................................................... 8 1.3 MEASUREMENT UNCERTAINTY .......................................................................................................... 9 2. SUMMARY OF TEST RESULTS .......................................................................................... 10 3. REQUIREMENTS AND TEST PROCEDURES .................................................................. 11 3.1 AC LINE CONDUCTED EMISSIONS .................................................................................................... 11 3.1.1 Applicable Standard ..................................................................................................................................... 11 3.1.2 EUT Setup.................................................................................................................................................... 12 3.1.3 EMI Test Receiver Setup ............................................................................................................................. 12 3.1.4 Test Procedure ............................................................................................................................................. 13 3.1.5 Corrected Amplitude & Margin Calculation ................................................................................................ 13 3.2 RADIATED SPURIOUS EMISSIONS ...................................................................................................... 14 3.2.1 Applicable Standard ..................................................................................................................................... 14 3.2.2 EUT Setup.................................................................................................................................................... 14 3.2.3 EMI Test Receiver & Spectrum Analyzer Setup ......................................................................................... 15 3.2.4 Test Procedure ............................................................................................................................................. 15 3.2.5 Corrected Amplitude & Margin Calculation ................................................................................................ 15 3.3 20 DB EMISSION BANDWIDTH ...........................................................................…

Text truncated - open the document above for the full version.

EXHIBIT D - TEST SETUP PHOTOGRAPHS Conducted Emissions Front View Conducted Emissions Side View Radiated Emission Below 1GHz View Radiated Emission Above 1GHz View