2AK9F-38112SMART WATCH

Issue description Incorrect step count Abnormal waggling or vibration of device Wear the watch properly to avoid abnormal vibration Possible cause Walked less than 15 steps Solution Watch failed to sync data to the App Sliding or walking in slippers The connected phone's Bluetooth is off Turn on the connected phone's Bluetooth Restart the "Fastrack Reflex World" App Out of Bluetooth signal range Make sure your watch is in close proximity to the connected phone App is shut down or has crashed Walk with normal posture/ wear something other than slippers Walk more than 15 steps continuously No display Connect to charger to charge the watch Low battery • Bluetooth BLE5.3 • Full-screen touch • 1.43" Amoled 466*466 pixel • Bluetooth call • Daily Tracking: Active/ Steps / Calories • SpO2 Blood Oxygen monitoring • Breathing training • Sleep monitoring report • Call notification • Find your phone • Music control • Camera control • Automatic recognition of motion • Pressure test • Female physical health Product Name Product Model FT_38112_XXXX Battery Capacity Working Temperature Storage Environment 300mAh 0 to 45 Temperature: -20 to 60 RelativeHumidity: ≤90%RH Bluetooth Name Frequency Range Bluetooth Transmitting Power FT_38112_XXXX 2402MHz-2480MHz < 1 dBm Charging Duration About 2 hours Waterproof RatingIP68 (1.5 meters) User Manual SMART WATCH • Matters needing attention The electronic equipment contained in the product, if improperly handled or disposed of, may damage the environment or cause harm: • Do not open the shell of the watch. • Do not replace the built-in battery by yourself. • Do not use corrosive cleaner to clean the product. • Do not charge when the product is wet. • If the product is not completely dry, do not charge. • Do not expose the product to extended periods of direct sunlight. • Do not use the product in a sauna or steam room. • Do not expose the product to extremely high or low temperatures. Regulatory Information ProcedureSettings>>Regulatory information(Label). This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. symptoms, please stop using the device and consult your doctor: - Epilepsy or sensitivity to light. - Poor blood circulation or excess bruising; heart disease or other diseases. - You are yaking any medicine that may make you sensitive to light. Warning: This Smart Watch FT_38112_XXXX is not a medical device. The Smart Watch FT_38112_XXXX and its related Apps can’ t be used to diagnose, treat, or prevent any disease or medical condition. Before performing any exercise, sleep, or nutritional changes, be sure to seek the advice of qualified medical professionals, otherwise serious injury or death may occur. This symbol means that according to local laws and regulations your product and or its battery shall be disposed of separately from household waste. When this product reaches its end of life, user has the choice to give his product to a competent recycling organization. Proper recycling of your product will protect human health and the environment. • Medical Disclaimer • Battery warning • Search the FCC ID number The built-in lithium battery of the product is forbidden to be disassembled, impacted, extruded or put into fire. The battery under the very low air pressure may result in explosion or flammable liquid or gas leakage. Avoid the battery in a high-temperature environment or being exposed to liquid or gas leakage. Avoid the battery in a high-temperature environment or being exposed to strong sunlight to avert explosion. Don't use the battery continuously in case of serious ballooning. The battery shall be handled pursuant to the local regulations and shall not be disposed as household garbage. Don't try to repair, remove or refit the battery. Explosion may happen if the battery is replaced by incorrect model. Don't compress or puncture the battery with hard object. The battery leakage, overheating or outbreak of a fire may occur if the battery is destroyed. 1.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device won't cause any harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has beentested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. • FCC statement • If the screen or shell is damaged, do not use the product. • Do not put the product in the dishwasher, washing machine or dryer. • Do not expose the product to fire, the battery…

Text truncated - open the document above for the full version.

1/1 US Agent for Service of Process LETTER OF ATTESTATION TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process: Company Name: Oasis Compliance, Inc. FRN: 0033464157 Contact Name: James He Address: 3313 Verdi Dr, San Jose, CA 95111 Telephone No: (202)602-8330 Email: [email protected] Applicant: Company name: Titan Company Limited Product Description: SMART WATCH Grantee code: 2AK9F FCC ID: 2AK9F-38112 Contact Name: Somprabh Kumar Singh Address: Integrity, #193, Veerasandra, Electronics City P.O., Off Hosur Main Road, Bangalore, India Telephone No: +918067046489 Email: [email protected] [Titan Company Limited] certifies that, as of the date of this filing of the application with the TCB, [Oasis Compliance, Inc.] is our designated US agent for service of process for the above referenced FCC ID. [Titan Company Limited] accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [Oasis Compliance, Inc.] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause § 2.911. Date: 7.22.2023 Applicant’s Name: Somprabh Kumar Singh US Agent’s Name: James He Title: CEO Title: Global Market Access Manager Signature Signature

C5266091_X24_Ed.2 1/1 “Attestation Statements” TO: Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for “covered” telecommunications equipment and video surveillance equipment produced by entities identified on the Commission’s Covered List 1 , which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name: Titan Company Limited Grantee code: 2AK9F FCC ID: 2AK9F-38112 Contact Name: Somprabh Kumar Singh Address: Integrity, #193, Veerasandra, Electronics City P.O., Off Hosur Main Road, Bangalore, India Telephone No: +918067046489 Fax No: +918067046262 Email: [email protected] i. [Titan Company Limited] (“the applicant”) certifies that the equipment for which authorization is sought is not “covered” equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii. [ Titan Company Limited] (“the applicant”) certifies that, as of the date of the filing of the application, the applicant is not (as a specifically named entity or any of its subsidiaries or affiliates) identified on the Covered List as an entity producing “covered” equipment. The applicant must sign this certification. Titan Company Limited. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Date: 7.2 2.2023 Applicant’s Name: Somprabh Kumar Singh Title: CEO Signature 1 The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist

C5266091_X8_Ed.1 1/1 Letter of Authorization Company: Titan Company Limited Address: Integrity, #193, Veerasandra, Electronics City P.O., Off Hosur Main Road, Bangalore, India Product Name: SMART WATCH Model Number: 38112 FCC Identifier: 2AK9F-38112 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, is allowed to forward all information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. Name: Somprabh Kumar Singh Date: 7/22/2023 Title: CEO Signature of applicant:

C5266091_X10_Ed.1 1/1 Titan Company Limited Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Date: 7/22/2023 Subject: Request for Confidentiality FCC ID: 2AK9F-38112 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits Long-Term Confidentiality Short-Term Confidentiality ID Label/Location No No Attestation Statement No No External Photos No Block Diagram Schematics Test Report No No Test Setup Photos No User’s Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) No No SDR Software / Security Info No Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Name: Somprabh Kumar Singh Date: 7/22/2023 Title: CEO

Page 1 of 4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel : (8 6-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Photographs of the EUT (External Photos) Model: 38112 Page 2 of 4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel : (8 6-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Page 3 of 4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel : (8 6-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Page 4 of 4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel : (8 6-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected]

Page 1 of 4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel : (8 6-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Photographs of the EUT (Internal Photos) Model: 38112 Page 2 of 4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel : (8 6-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] ANT Page 3 of 4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel : (8 6-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Page 4 of 4 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel : (8 6-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected]

Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] RF EXPOSURE Test Report Report No.: MTi230621014-04E3 Date of issue: 2023-07-17 Applicant: Titan Company Limited Product: SMART WATCH Model(s): 38112 FCC ID: 2AK9F-38112 Shenzhen Microtest Co., Ltd. http://www.mtitest.com - Page 2 of 6- Report No.: MTi230621014-04E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Instructions 1. The report shall not be partially reproduced without the written consent of the laboratory; 2. The test results of this report are only responsible for the samples submitted; 3. This report is invalid without the seal and signature of the laboratory; 4. This report is invalid if transferred, altered or tampered with in any form without authorization; 5. Any objection to this report shall be submitted to the laboratory within 15 days from the date of receipt of the report. - Page 3 of 6- Report No.: MTi230621014-04E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Applicant: Titan Company Limited Address: Integrity, #193, Veerasandra, Electronics City P.O., Off Hosur Main Road, Bangalore, India. Manufacturer: FUHONGDA Technology Co. Ltd. Address: No. 222, 1st Floor, Building A, South Gate, Wanliye Science and Technology Park, No. 4, Fuyong Chongqing Road, Baoan District， Shenzhen, Guangdong, China. Product description Product name: SMART WATCH Trademark: FASTRACK Model name: 38112 Serial Model: N/A Standards: N/A Test method: KDB 447498 D01 v06 Date of Test Date of test: 2023-06 -30 to 2023-07 -10 Test result: Pass Test Engineer : (Maleah Deng) Reviewed By: : (Leon Chen) Approved By: : (Tom Xue) - Page 4 of 6- Report No.: MTi230621014-04E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Table of Contents 1. STANDALONE SAR TEST EXCLUSION CONSIDERATIONS ............................................................................................ 5 2. SAR TEST EXCLUCSION THRESHOLDS ........................................................................................................................ 6 - Page 5 of 6- Report No.: MTi230621014-04E3 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China. Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] 1. Standalone SAR test exclusion considerations Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Test Exclusion Threshold condition(s), listed below, is (are) satisfied. These test exclusion conditions are based on source-based time-averaged maximum conducted output power of the RF channel requiring evaluation, adjusted for tune-up tolerance, and the minimum test separation distance required for the exposure conditions. The minimum test separation distance defined in 4.1 f) is determined by the smallest distance from the antenna and radiating structures or outer surface of the device, according to the host form factor, exposure conditions and platform requirements, to any part of the body or extremity of a user or bystander. To qualify for SAR test exclusion, the test separation distances applied must be fully explained and justified, typically in the SAR measurement or SAR analysis report, by the operating configurations and exposure conditions of the transmitter and applicable host platform requirements, according to the required published RF exposure KDB procedures. When no other RF exposure testing or reporting are required, a statement of justification and compliance must be included in the equipment approval, in lieu of the SAR report, to qualify for SAR test exclusion. When required, the device specific conditions described in the other published RF exposure KDB procedures must be satisfied before applying these SAR test exclusion provisions. a) For 100 MHz to 6 GHz and test separation distances ≤ 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following: [(max. power of channel, including tune-up tolerance, mW) / (min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR, and ≤ 7.5 for 10-g extremity SAR, where  f (GHz) is the RF channel transmit frequency in GHz  Power and distance are rounded to the nearest mW and mm before calculation  The result is rounded to one decimal place for comparison  The values 3.0 and 7.5 are referred to as numeric thresholds in step b) below The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm, and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm according to 4.1 f) is applied to determine SAR test exclusion. b) For 100 MHz to 6 GHz and test separation distances > 50 mm, the 1-g and 10-g SAR test exclusion thresholds are determined by the following (also illustrated in Appendix B): 1) {[Power allowed at numeric threshold for 50 mm in step a)] + [(test separation distance – 50 mm)·(f(MHz)/150)]} mW, for 100 MHz to 1500 MHz 2) {[Power allowed at numeric threshold for 50 mm in step a)] + [(test separation distance – 50 mm)·10]}…

Text truncated - open the document above for the full version.

第 1 页 / 共计 5 页 天线样品承认书 AntennaSampleConfirmation 设计单位：深圳市凯普深通讯科技有限公司 Designer ： ShenzhenKaipushenCommunicationTechnologyCo.,Ltd 地 址：深圳市龙华区龙观大道 440 号龙城工业区御龙办公楼二楼 Add ： 2Floor,YulongOfficebuilding,LongchengIndustrialZone,440LongguanRoad,LonghuaDistrict, Shenzhen,China 客户名称 Customer 深圳市泰辑物联网科技有限公司 ShenzhenTaijiInternetofThingsTechnologyCo.,Ltd 深圳市凯普深通讯科技有限公司 ShenzhenKaipushenCommunicationTechnologyCo.,Ltd 项目名称 ProjectName OY70T 日期 2023-06-20 Date 物料编号 ProjectNO. 备注 蓝牙导线 Bluetoothwire 0.8*20mm Notes 客户料号 CustomerMaterialNo G0115010002 频段 FrequencyRange BT 设计 DesignedBy RF Engineer StructuralEngineer 审核 CheckedBy EngineeringManager 客户确认 Client’sApproval 第 3 页 / 共计 5 页 目 录 Catalogue 封面 Frontcover ............................................................................................................................. 1 目录 Catalogue ................................................................................................................................ 3 1. 规格书概述 Overviewofspecifications ...............................................................................................4 2.LDS 天线外观 Antennaappearance ....................................................................................................4 3. 电性能 Electrical .................................................................................................................................4 3.1. 天线频段 Antennaband .........................................................................................................................4 3.2. 匹配电路 Matchingcircuit .......................................................................................................................4 3.3. 回波损耗 ReturnLoss .............................................................................................................................5 3.4. 天线增益 AntennaGain ......................................................................................................5 4. 外观结构 Skinstructure .....................................................................................................................6 4.1.LDS 天线材质 Antennamaterial ...........................................................................................................6 5. 备注 Remarks .......................................................................................................................................6 6. 附录一 Appendix1 ：结构图纸 Structuraldrawings ..........................................................................7 第 4 页 / 共计 5 页 1. 规格书概述 Overviewofspecifications 该规格书描述 OY70T 内置式导线天线的状况，其频段为 BT 。 ThisspecificationdescribestheconditionofOY70Tbuilt-inwireantenna,ItsfrequencybandisBT. 2. 天线外观 Antennaappearance 3. 电性能 Electrical 3.1. 天线频段 Antennaband BT 发射频段 (MHz) 2400MHz-2480MHz 3.2. 匹配电路 M atchingcircuit 测试点是天线焊盘，见下图 Thetestpointisthebondingpadofantenna,asshownbelow. 1. BT 天线匹配 M atchedantenna 。 ElementValue E12.2PF E20R E30.75PF 第 5 页 / 共计 5 页 3.3. 回波损耗 ReturnLoss BTVSWR+Return 谐振点范围 (MHz) 频点 (MHz)/ 最大回波损耗 (dB) 2400-2500 24002480 VSWR 1.042.01 Returnloss -12.38-10.54 3.4 天线增益 Antennagain Channel03978 Gain-2.69dBi-2.54dBi-2.98dBi Gaindiagram 自由空间 手模 FreespaceHandMold 第 6 页 / 共计 5 页 4. 外观结构 Appearanceandstructure 4.1. 天线材质 Antennamaterial 导线天线 Wireantenna 5. 备注

The test report is only u sed for customer scientific research, teaching, internal quality control and other purposes, and is for internal reference only. Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Test Report Report No.: MTi230621014-04E1 Date of issue: 2023-07-17 Applicant: Titan Company Limited Product: SMART WATCH Model(s): 38112 FCC ID: 2AK9F-38112 Shenzhen Microtest Co., Ltd. http://www .mtitest.com Page 2 of 79 Report No.: MTi230621014-04E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Instructions 1. This test report shall not be partially reproduced without the written consent of the laboratory. 2. The test results in this test report are only responsible for the samples submitted 3. This test report is invalid without the seal and signature of the laboratory. 4. This test report is invalid if transferred, altered, or tampered with in any form without authorization. 5. Any objection to this test report shall be submitted to the laboratory within 15 days from the date of receipt of the report. Page 3 of 79 Report No.: MTi230621014-04E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] Table of contents 1 General Description ........................................................................................................................... 5 1.1 Description of the EUT ............................................................................................................................... 5 1.2 Description of test modes .......................................................................................................................... 5 1.3 Environmental Conditions .......................................................................................................................... 8 1.4 Description of support units ....................................................................................................................... 8 1.5 Measurement uncertainty .......................................................................................................................... 8 2 Summary of Test Result .................................................................................................................... 9 3 Test Facilities and accreditations ................................................................................................... 10 3.1 Test laboratory ......................................................................................................................................... 10 4 List of test equipment ...................................................................................................................... 11 5 Evaluation Results (Evaluation) ..................................................................................................... 14 5.1 Antenna requirement ............................................................................................................................... 14 6 Radio Spectrum Matter Test Results (RF) ..................................................................................... 14 6.1 Conducted Emission at AC power line .................................................................................................... 14 6.2 Occupied Bandwidth ................................................................................................................................ 18 6.3 Maximum Conducted Output Power ........................................................................................................ 20 6.4 Channel Separation ................................................................................................................................. 22 6.5 Number of Hopping Frequencies ............................................................................................................. 24 6.6 Dwell Time ............................................................................................................................................... 26 6.7 Emissions in non-restricted frequency bands .......................................................................................... 28 6.8 Band edge emissions (Radiated)............................................................................................................. 30 6.9 Emissions in restricted frequency bands (below 1GHz) .......................................................................... 35 6.10 Emissions in restricted frequency bands (above 1GHz) ......................................................................... 39 Photographs of the test setup ............................................................................................................... 46 Photographs of the EUT ........................................................................................................................ 47 Appendix A: 20dB Emission Bandwidth .............................................................................................. 48 Appendix B: Maximum conducted output power ................................................................................ 52 Appendix C: Carrier frequency separation .......................................................................................... 56 Appendix D: Time of occupancy ........................................................................................................... 58 Appendix E: Number of hopping channels .............................................…

Text truncated - open the document above for the full version.

Page 51 of 79 Report No.: MTi230621014-04E1 Address: 101, No. 7, Zone 2, Xinxing Industrial Park, Fuhai Avenue, Xinhe Community, Fuhai Street, Bao’an District, Shenzhen, Guangdong, China Tel: (86-755)88850135 Fax: (86-755) 88850136 Web: www.mtitest.com E-mail: [email protected] 3DH5_Ant1_2441 3DH5_Ant1_2480 Page 52 of 79 Report No.: MTi23…

Text truncated - open the document above for the full version.