2ALB3AW70DECT 6.0 Headsets System - Base(BT) Unit

(For model AW70 & AW80 only) (AW70 & AW80 Base) PC (For model AW70 & AW80 only) (For model AW70 & AW80 only) (For model AW70 & AW80 only) (For model AW70 & AW80 only) Agent Headsets Inc 7901 4th Street North STE St Petersburg, Florida US 33702 Phone: +1 7272910121 Safety: EN IEC 62368-1:2020+A11: 2020 N12.2.3 (2019-11) N73.2.4 (2020-09) TSI EN 301489-6 V2.2.1 (2019-04) .2.2 (2016-09) EN 300328 V2.2.2 (2019-07) SAREN 62479: 2010 50663: 2017 EMC: E 301489- V E 301489-1 V E RF: EN 301406 V2 : EN

ŸUse only power supplies and rechargeable battery listed in below. CAUTION Power adaptor model: ZHT061U-0850500 8.5V 500mA (CHNHT INTERNATIONAL (HK) CO LIMITED) Battery model: 451645, Lithium-ion battery, 3.7V, 190mAh (OI NAN TECHNOLOGY LTD) ŸRisk of explosion if battery is replaced by incorrect type disposed of used batteries according to the instruction. ŸBattery cannot be subjected to high or low extreme temperatures, low air pressure at high altitude during use, storage or transportation. Safety Instruction ŸReplacement of a battery with an incorrect type that can result in an explosion or the leakage of flammable liquid or gas. ŸDisposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion. ŸReorient or relocate the receiving antenna For Base unit: The USB cable(s) included in this package must be used with this product to ensure compliance with the Class B FCC limits. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and ŸNOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installtion. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ŸA battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas. ŸIncrease the separation between the equipment and receiver ŸOperating, charging and storage temperatures are 32 ̊F to 104 ̊F (0 ̊C to 40 ̊C) (2) this device must accept any interference received, including interference that may cause undesired operation. ŸLeaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas. ŸConsult the dealer or an experienced radio/TV technician for help ŸFor PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall be easily accessible Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This product compliances with FCC RF radiation exposure limits set forth for an uncontrolled environment. Caution: To maintain the compliance with FCC’s RF exposure guidance, place the Base unit at least 20cm from nearby persons. ŸThe applied nameplate is located at the bottom of the product’s base. ŸConnect the equipment into an outlet on a circuit different from that to which the receiver is connected RF Radiation Exposure The USB port on base station is for data transfer only without charging function. Agent Headsets Inc St Petersbury, Florida Should you experience troubles with this equipment in the US, please contact: 7901 4th Street North STE Tel: 1-727-291-0121 Industry Canada This device contains licence-exempt transmitter(s)receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference 2. This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian requirements CAN ICES-003(B)/NMB-003 (B) US 33702 (2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ŸLa mise au rebut d'une batterie dans un feu ou un four chaud, ou l'écrasement ou la découpe d'une batterie, peut entraîner une explosion. ŸUtilisez uniquement les alimentations et la batterie rechargeable énumérées ci-dessous. ŸLaisser une batterie à des températures très élevées peut provoquer une explosion ou une fuite de liquide ou de gaz inflammable. (1) L'appareil ne doit pas produire de brouillage; CAN ICES-003 (B) / NMB-003 (B) Instructions de Sécurité ŸUne batterie sous très faible pression d'air peut causer une explosion ou une fuite de liquide ou de gaz inflammable. ŸPour l'équipement à brancher, la prise doit être proche de l'équipement et facile d'accès. Adaptateur secteur modele: ZHT061U-0850500 8.5V 500mA (CHNHT INTERNATIONAL (HK) CO LIMITED) L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : L’UNITÉ DE BASE: ŸMettre au rebut les batteries usagées conformément aux réglementations locales. Modele de batterie: 451645, Lithium-ion battery, 3.7V, 190mAh (OI NAN TECHNOLOGY LTD) ŸLa batterie ne doit pas être soumise à des températures extrêmement élevées ou basses ou à une basse pression atmosphérique à haute altitude pendant son utilisation, son entreposage ou son transport. ATTENTION: Pour maintenir la conformité aux directives d'exposition aux radiofréquences de la FCC, placez l'unité de base au moins 20 cm des personnes proches. ŸLa plaque signalétique se trouve en bas de la base du produit. ŸLes températures de fonctionnement, de charge et d’entreposage sont de 0 °C à 40 °C (32 °F à 104 °F) PRÉCAUTION ŸATTENTION: Remplacer une batterie par une batterie incorrecte peut provoquer une explosion ou une fuite de liquide ou de gaz inflammable.

IPN Headsets

INTERTEK TESTING SERVICES External Photos FCC ID: 2ALB3AW70 IC: 23665-HS021 INTERTEK TESTING SERVICES External Photos FCC ID: 2ALB3AW70 IC: 23665-HS021 INTERTEK TESTING SERVICES External Photos FCC ID: 2ALB3AW70 IC: 23665-HS021

CM US C Intertek 5008497 A/V C.I. T.E. CM US C Intertek 5008497 A/V C.I. T.E. CM US C Intertek 5008497 A/V C.I. T.E. Model: AW60 Model: AW70 Model: AW80 IC: 23665-HS020 IC: 23665-HS021 IC: 23665-HS021 FCC ID: 2ALB3AW50 FCC ID: 2ALB3AW70 FCC ID: 2ALB3AW70 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. 5 060447 341550 5 060447 341567 5 060447 341574 Agent AW60 Wireless DECT Binaural Headset Agent AW70 Wireless DECT Monaural Headset Agent AW80 Wireless DECT Binaural Headset P/N: AG22-0701 P/N: AG22-0702 P/N: AG22-0703 009043 009043 009043 009043 MC YA 009043 MC YA 009043 MC YA Serial No. Serial No. Serial No. Date Date Date Made in China Made in China Made in China CM US C Intertek 5008497 A/V C.I. T.E. Model: AW50 IC: 23665-HS020 FCC ID: 2ALB3AW50 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. 5 060447 341543 Agent AW50 Wireless DECT Monaural Headset P/N: AG22-0700 009043 009043 MC YA Serial No.Date Made in China CM US C Intertek 5008497 A/V C.I. T.E. Model: AW50 IC: 23665-HS020 FCC ID: 2ALB3AW50 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. 5 060447 341543 Agent AW50 Wireless DECT Monaural Headset P/N: AG22-0700 009043 009043 MC YA Serial No.Date Made in China Label Dimension: 52 x 52mm Label Dimension: 52 x 52mm Label Dimension: 52 x 52mm Label Dimension: 52 x 52mm Show Label Location only

INTERTEK TESTING SERVICES Internal Photos FCC ID: 2ALB3AW70 IC: 23665-HS021 INTERTEK TESTING SERVICES Internal Photos FCC ID: 2ALB3AW70 IC: 23665-HS021 INTERTEK TESTING SERVICES Internal Photos FCC ID: 2ALB3AW70 IC: 23665-HS021 INTERTEK TESTING SERVICES Internal Photos FCC ID: 2ALB3AW70 IC: 23665-HS021 INTERTEK TESTING SERVICES Internal Photos FCC ID: 2ALB3AW70 IC: 23665-HS021 INTERTEK TESTING SERVICES Internal Photos FCC ID: 2ALB3AW70 IC: 23665-HS021 INTERTEK TESTING SERVICES Internal Photos FCC ID: 2ALB3AW70 IC: 23665-HS021 INTERTEK TESTING SERVICES Internal Photos FCC ID: 2ALB3AW70 IC: 23665-HS021 INTERTEK TESTING SERVICES Internal Photos FCC ID: 2ALB3AW70 IC: 23665-HS021 INTERTEK TESTING SERVICES Internal Photos FCC ID: 2ALB3AW70 IC: 23665-HS021

INTERTEK TESTING SERVICES FCC ID: 2ALB3AW80 RF exposure - 1 of 1 For Maximum Permissible Exposure (MPE) evaluation of the base unit, the maximum power density at 20 cm from this mobile transmitter shall be less than the General Population / Uncontrolled MPE limit in OET Bulletin 65 and meet the requirement listed in KDB447498. For the 1.9GHz DECT Transmission of tested model: AW80, the measured powers among all the measured channels were within its production tolerance: +10 dBm (Minimum) and +20 dBm (Maximum). The antenna gain of AW80 is 1.3 dBi = 1.35 (num gain) and its maximum source-based time-averaging duty factor is 12.5% (3/24 x100%). From these data and its operating configuration – Mobile device, the exposed power density at a distance (R) of 20cm from the center of radiation of the antenna can be calculated according to OET Bulletin 65 as follow: The Conducted Power = 20 dBm = 100.0 mW The Conducted Power source-based time-averaging output power = (100.0 * 0.125) mW = 12.5 mW The power density at 20cm = 12.5 *1.35/ 4πR 2 = 0.0034 mW cm -2 For the 2.4GHz Bluetooth Transmission of tested model: AW80, the measured powers among all the measured channels were within its production tolerance: +0 dBm (Minimum) and +7 dBm (Maximum). The antenna gain of AW80 is -2.18 dBi = 0.61 (num gain) and its maximum source-based time-averaging duty factor is 100.0% (6/6 x100%). From these data and its operating configuration – Mobile device, the exposed power density at a distance (R) of 20cm from the center of radiation of the antenna can be calculated according to OET Bulletin 65 as follow: The Conducted Power = 7 dBm = 5.0 mW The Conducted Power source-based time-averaging output power = (5.0 * 1.000) mW = 5.01 mW The power density at 20cm = 5.01 *0.61/ 4πR 2 = 0.0006 mW cm -2 INTERTEK TESTING SERVICES FCC ID: 2ALB3AW80 RF exposure - 1 of 1 Per KDB 447498 D01 v06, simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on calculated or measured field strengths or power density, is ≤ 1.0. The MPE ratio for DECT Transmission can be calculated as follow: = The power density at 20cm / MPE limit = 0.0034 mW cm -2 / 1.0 mW cm -2 = 0.0034 The MPE ratio for Bluetooth Transmission can be calculated as follow: = The power density at 20cm / MPE limit = 0.0006 mW cm -2 / 1.0 mW cm -2 = 0.0006 The sum of the MPE ratios for all simultaneous transmitting antennas = 0.0034 + 0.0006 = 0.0040 As the sum of MPE ratios for all simultaneous transmitting antennas is ≤ 1.0, simultaneous transmission MPE test exclusion will be applied. Conclusion In frequency range of 1,500 - 100,000MHz, the MPE limit is 1.0 mWcm -2 for general population and uncontrolled exposure. As simultaneous transmission MPE test exclusion is applied and the measured power density at 20cm from all the standalone transmissions is lower than the MPE limit, the compliance to the MPE limit can be ensured by indicating the minimum 20cm separation between the transmitter's radiating structures and body of the user or nearby persons. The following RF exposure statement is proposed to be included in the user manual: “ FCC RF Radiation Exposure Statement Caution: To maintain compliance with the FCC’s RF exposure guidelines, place the base unit at least 20cm from nearby persons.”

TEST REPORT 2/F., Garment Centre, 576 Castle Peak Road, Kowloon, Hong Kong SAR, China. Telephone: (852) 2173 8888 Facsimile: (852) 2785 5487 www.intertek.com Intertek’s standard Terms and Conditions can be obtained at our website http://www.intertek.com/terms/. The test report only allows to be revised within the retention period unless further standard or the requirement was noticed. This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. © 2017 Intertek Page 1 of 24 Report No.: 22080645HKG-003 IPN Headsets Application For Original Grant of 47 CFR Part 15 Certification DECT 6.0 Headset System - Base (BT) Unit FCC ID: 2ALB3AW70 Prepared and Checked by: Approved by: Signed on File Wong Cheuk Ho, Herbert Wong Kwok Yeung, Kenneth Assistant Supervisor Assistant Manager Date: May 12, 2023 TEST REPORT IPN Headsets Intertek Report No: 22080645HKG-003 Page 2 of 24 GENERAL INFORMATION Grantee: IPN Headsets Grantee Address: Bijsterhuizen 2414, 6604 LL Wijchen, The Netherlands. FCC Specification Standard: FCC Part 15, October 1, 2021 Edition FCC ID: 2ALB3AW70 FCC Model(s): AW80, AW70, AWX0 Type of EUT: Transceiver Description of EUT: DECT 6.0 Headset System - Base (BT) Unit Sample Receipt Date: August 16, 2022 Date of Test: August 16, 2022 to April 04, 2023 Report Date: May 12, 2023 Environmental Conditions: Temperature: +10 to 40°C Relative Humidity: 10 to 90% Conclusion: Test was conducted by client submitted sample. The submitted sample as received complied with the 47 CFR Part 15 Certification. TEST REPORT IPN Headsets Intertek Report No: 22080645HKG-003 Page 3 of 24 SUMMARY OF TEST RESULT Test Items FCC Part 15 Section Results Transmitter Power Line Conducted Emissions 15.207 Complied Radiated Emission 15.249, 15.209 Complied Radiated Emission on the Bandedge Complied Radiated Emission in Restricted Bands 15.205 Complied The equipment under test is found to be complying with the following standards: FCC Part 15, October 1, 2021 Edition Note: 1. The EUT uses a permanently attached antenna which, in accordance to section 15.203, is considered sufficient to comply with the previsions of this section. 2. Pursuant to FCC Part 15 Section 15.215(c), the 20dB bandwidth of the emission was contained within the frequency band designated (mentioned as above) which the EUT operated. The effects, if any, from frequency sweeping, frequency hopping, other modulation techniques and frequency stability over expected variations in temperature and supply voltage were considered. TEST REPORT IPN Headsets Intertek Report No: 22080645HKG-003 Page 4 of 24 TABLE OF CONTENTS 1.0 GENERAL DESCRIPTION ................................................................................................ 5 1.1 Product Description .................................................................................................. 5 1.2 Related Submittal(s) Grants ...................................................................................... 5 1.3 Test Methodology ..................................................................................................... 5 1.4 Test Facility ................................................................................................................ 5 2.0 SYSTEM TEST CONFIGURATION .................................................................................... 6 2.1 Justification ............................................................................................................... 6 2.2 EUT Exercising Software............................................................................................ 6 2.3 Special Accessories .................................................................................................... 6 2.4 Measurement Uncertainty........................................................................................ 6 2.5 Support Equipment List and Description .................................................................. 7 3.0 EMISSION RESULTS ...................................................................................................... 8 3.1 Field Strength Calculation ......................................................................................... 8 3.2 Radiated Emission Configuration Photograph .......................................................... 9 3.3 Radiated Emission Data ............................................................................................ 9 3.4 Conducted Emission Configuration Photograph ...................................................... 9 3.5 Conducted Emission Data ......................................................................................... 9 4.0 EQUIPMENT PHOTOGRAPHS...................................................................................... 15 5.0 PRODUCT LABELLING ................................................................................................. 15 6.0 TECHNICAL SPECIFICATIONS ...................................................................................... 15 7.0 INSTRUCTION MANUAL ............................................................................................. 15 8.0 MISCELLANEOUS IN…

Text truncated - open the document above for the full version.

NOTE:ThisdocumentisissuedbyShenzhenMorlabCommunicationsTechnologyCo.,Ltd.,thetestreportshallnotbereproducedexceptin fullwithoutpriorwrittenpermissionofthecompany.Thetestresultsapplyonlytotheparticularsample(s)testedandtothespecifictestscarried outwhichisavailableonrequestforvalidationandinformationconfirmedatourwebsite. MORLAB SHENZHENMORLABCOMMUNICATIONSTECHNOLOGYCo.,Ltd. FL1-3,BuildingA,FeiYangSciencePark,No.8LongChangRoad, Block67,BaoAnDistrict,ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page1of 12 REPORTNo.：SZ22100214E02 TESTREPORT APPLICANT:OrchidElectronicsLimited PRODUCTNAME:BluetoothModuleAntenna MODELNAME:OEL_ANT_002 TRADENAME:N/A BRANDNAME:N/A STANDARD(S):IEEEStd149-2021 RECEIPTDATE:2022-10-24 TESTDATE:2022-10-25 ISSUEDATE:2022-12-26 Editedby: : FangJinshan(Rapporteur) Approvedby: : ChiShide(Supervisor) Testedby MORLAB SHENZHENMORLABCOMMUNICATIONSTECHNOLOGYCo.,Ltd. FL1-3,BuildingA,FeiYangSciencePark,No.8LongChangRoad, Block67,BaoAnDistrict,ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page2of12 REPORTNo.：SZ22100214E02 DIRECTORY 1.TechnicalInformation ........................................................................................................3 1.1.ApplicantandManufacturerInformation ....................................................................3 1.2.EquipmentUnderTest(EUT)Description...................................................................3 2.TestResults........................................................................................................................4 2.1.AppliedReferenceDocuments.....................................................................................4 2.2.TestConditions...............................................................................................................4 2.3.MeasurementUncertainty.............................................................................................4 2.4.TestResults.....................................................................................................................5 AnnexATestSetupPhotos..................................................................................................6 AnnexBFigures .....................................................................................................................7 1 ． 2DRadiationPattern ......................................................................................................7 2 ． 3DRadiationPattern ......................................................................................................8 AnnexCEUTPhotos ...........................................................................................................10 AnnexDGeneralInformation .............................................................................................12 1.1IdentificationoftheResponsibleTestingLaboratory..............................................12 1.2IdentificationoftheResponsibleTestingLocation..................................................12 1.3TestEquipmentsUtilized..............................................................................................12 ChangeHistory VersionDateReasonforchange 1.02022-12-26Firstedition MORLAB SHENZHENMORLABCOMMUNICATIONSTECHNOLOGYCo.,Ltd. FL1-3,BuildingA,FeiYangSciencePark,No.8LongChangRoad, Block67,BaoAnDistrict,ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page3of12 REPORTNo.：SZ22100214E02 1.TechnicalInformation Note:Providebymanufacturer. 1.1.ApplicantandManufacturerInformation Applicant:OrchidElectronicsLimited ApplicantAddress:Unit702,7/Fl.,OneHungToRoad,KwunTong,HongKong Manufacturer:OiNanTechnologyLimited ManufacturerAddress:4YinShaLu2Jie,XiaBin,CheungOn,DongGuan,Guangdong, China 1.2.EquipmentUnderTest(EUT)Description WirelessType Bluetooth Frequency N/A IMEI N/A SampleNo.2# Dimensions: MORLAB SHENZHENMORLABCOMMUNICATIONSTECHNOLOGYCo.,Ltd. FL1-3,BuildingA,FeiYangSciencePark,No.8LongChangRoad, Block67,BaoAnDistrict,ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page4of12 REPORTNo.：SZ22100214E02 2.TestResults 2.1.AppliedReferenceDocuments Leadingreferencedocumentsfortesting: No.IdentityDocumentTitle 1 IEEEStd149-2021 IEEERecommendedPracticeforAntenna Measurements 2.2.TestConditions TestEnvironmentConditions ： RelativeHumidity:25...75% Temperature:+10°Cto+30°C 2.3.MeasurementUncertainty Theuncertaintyiscalculatedusingthemethodssuggestedinthe"GuidetotheExpressionof UncertaintyinMeasurement"(GUM)publishedbyISO.Whenthetestresultisacriticalvalue,we willusethemeasurementuncertaintygivethejudgmentresultbasedonthe95%Confidence intervals. ItemMeasurementUncertainty(dB) Gain±0.5 VSWR±0.2 MeasurementUncertainty(95%ConfidenceInterval)K=2 MORLAB SHENZHENMORLABCOMMUNICATIONSTECHNOLOGYCo.,Ltd. FL1-3,BuildingA,FeiYangSciencePark,No.8LongChangRoad, Block67,BaoAnDistrict,ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page5of12 REPORTNo.：SZ22100214E02 2.4.TestResults Frequency (MHz) Gain(dBi) 2400 -3.39 2410-2.94 2420 -2.79 2430-2.73 2440 -2.45 2450-2.27 2460 -2.18 2470-2.20 2480 -2.45 2490-2.67 2500 -2.76 MORLAB SHENZHENMORLABCOMMUNICATIONSTECHNOLOGYCo.,Ltd. FL1-3,BuildingA,FeiYangSciencePark,No.8LongChangRoad, Block67,BaoAnDistrict,ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page6of12 REPORTNo.：SZ22100214E02 AnnexATestSetupPhotos MORLAB SHENZHENMORLABCOMMUNICATIONSTECHNOLOGYCo.,Ltd. FL1-3,BuildingA,FeiYangSciencePark,No.8LongChangRoad, Block67,BaoAnDistrict,ShenZhen,GuangDongProvince,P.R.China Tel:86-755-36698555Fax:86-755-36698525 Http://www.morlab.cnE-mail:[email protected] Page7of12 REPORTNo.：SZ22100214E02 AnnexBFig…

Text truncated - open the document above for the full version.

INTERTEK TESTING SERVICES The Worst Case Configuration Photographs FCC ID: 2ALB3AW70 IC: 23665-HS021 Radiated Emission – Base(BT) Unit Front View Rear View The EUT is placed at the center of turntable INTERTEK TESTING SERVICES The Worst Case Configuration Photographs FCC ID: 2ALB3AW70 IC: 23665-HS021 AC Conducted Emission Front View Side View 1 INTERTEK TESTING SERVICES The Worst Case Configuration Photographs FCC ID: 2ALB3AW70 IC: 23665-HS021 AC Conducted Emission Side View 2